Ford 2005 F-150 manual

Introduction 4 Instrument Cluster 10 W arning and control lights 10 Gauges 15 Entertainment Systems 18 AM/FM stereo 18 AM/FM stereo with CD 20 AM/FM stereo cassette with CD 23 AM/FM stereo with in-dash six CD 26 Climate Controls 32 Heater only 32 Manual heating and air conditioning 33 Automatic temperature control 36 Rear window defroster 41 Lights[...]

Locks and Security 85 Keys 85 Locks 85 Anti-theft system 96 Seating and Safety Restraints 100 Seating 100 Safety restraints 105 Airbags 124 Child restraints 132 Tires, Wheels and Loading 149 T ire Information 151 T ire Inflation 154 Changing tires 157 Lug Nut T orque 163 V ehicle loading 172 T railer towing 179 Recreational towing 187 Driving 189 S[...]

Customer Assistance 237 Reporting safety defects (U.S. only) 245 Cleaning 246 Maintenance and Specifications 254 Engine compartment 256 Engine oil 259 Battery 263 Engine Coolant 265 Fuel information 271 Air filter(s) 289 Part numbers 291 Refill capacities 292 Lubricant specifications 295 Accessories 304 Index 307 All rights reserved. Reproduction b[...]

CALIFORNIA Proposition 65 W arning W ARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemic[...]

W arning symbols on your vehicle When you see this symbol, it is imperative that you consult the relevant section of this guide before touching or attempting adjustment of any kind. Protecting the environment W e must all play our part in protecting the environment. Correct vehicle usage and the authorized disposal of waste, cleaning and lubricatio[...]

Service Data Recording Service data recorders in your vehicle are capable of collecting and storing diagnostic information about your vehicle. This potentially includes information about the performance or status of various systems and modules in the vehicle, such as engine, throttle, steering or brake systems. In order to properly diagnose and ser[...]

Front seat mounted rear -facing child or infant seats should NEVER be placed in front of an active passenger air bag. Using your vehicle with a snowplow For more information and guidelines for using your vehicle with a snowplow , refer to the Driving chapter . F150 SuperCrew Owners: Snowplowing Y our vehicle is not recommended for snowplowing. Ford[...]

These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner’ s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat Installation W arning Child Seat Lower Anchor Child Seat T ether Anchor Brake System Anti-Lock Brake System Brake Fluid - Non-Petroleum Based Powertrain Malfunction[...]

V ehicle Symbol Glossary Power W indows Front/Rear Power W indow Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant T emperature Do Not Open When Hot Battery A void Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan W arning Power Steering Fluid Maintain Corr[...]

W ARNING LIGHTS AND CHIMES Base instrument cluster Base with T achometer instrument cluster Mid instrument cluster 2005 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus) Instrument Cluster 10[...]

Luxury instrument cluster W arning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’ s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works. If any light remains o[...]

On vehicles equipped with a message center , “ENGINE F AILSAFE MODE” will be displayed, refer to Message Center in the Driver Controls chapter . Brake system warning light: T o confirm the brake system warning light is functional, it will momentarily illuminate when the ignition is turned to the ON position when the engine is not running, or in[...]

Safety belt: Reminds you to fasten your safety belt. A chime will also sound to remind you to fasten your safety belt. Charging system: Illuminates when the battery is not charging properly . Door ajar: Illuminates when the ignition is in the ON position and any door is open. Overdrive off (if equipped): Illuminates when the overdrive function of t[...]

MINI MESSAGE CENTER WARNING DISPLAYS (IF EQUIPPED) Door ajar: Displays when the ignition is in the ON position and any door is open. Low fuel: Displays when the fuel level in the fuel tank is at or near empty (refer to Fuel gauge in this chapter). Check fuel cap: Displays when the fuel cap may not be properly installed. Continued driving with this [...]

GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the e[...]

• W ith Full Message Center Refer to Message Center in the Drivers Controls chapter on how to switch the display from Metric to English. T rip odometer: Registers the miles (kilometers) of individual journeys. • W ith Mini Message Center Press and release the button on top of the cluster to toggle between odometer and trip odometer display . ?[...]

Engine oil pressure gauge: Indicates engine oil pressure. The needle should stay in the normal operating range (between “L” and “H”). If the needle falls below the normal range, stop the vehicle, turn off the engine and check the engine oil level. Add oil if needed. If the oil level is correct, have your vehicle checked at your authorized d[...]

FORD AM/FM STEREO SYSTEM (IF EQUIPPED) 1. / T une: Press to manually go up or down the radio frequency . Also use in menu mode to select various settings. 2. Audio: Press to access select various settings. T reble: Press to adjust the treble setting. Use / / SEEK, SEEK . Bass: Press to adjust the bass setting. Use / / SEEK, SEEK . Balance: Press to[...]

Setting the clock: Press until HR or Mn is displayed. Press // SEEK to adjust the hours/minutes. 3. Seek: Press to access the next/previous strong station. 4. Memory presets: T o set a station: Select frequency band AM/FM; tune to a station, press and hold a preset button until sound returns. 5. AM/FM: Press to select AM/FM frequency band. 6. ON/OF[...]

FORD SINGLE CD SOUND SYSTEM (IF EQUIPPED) 1. / T une: Press to manually go up or down the radio frequency . Also use in menu mode to select various settings. 2. Phone/mute: Press to mute the playing media. Press again to return to the playing media. 3. Menu: Press to toggle through the following modes: T reble: Press to adjust the treble setting. U[...]

Fade: Press to adjust the audio between the front and rear speakers. Use / / SEEK, SEEK . Speed sensitive volume: Radio volume automatically changes slightly with vehicle speed to compensate for road and wind noise. Use / / SEEK, SEEK to adjust. Autoset: Allows you to set the strongest local radio stations without losing your original manually set [...]

10. Fast forward: Press to manually advance in a CD track. 11. Rewind: Press to manually reverse in a CD track. 12. Memory presets: T o set a station: Select frequency band AM/FM; tune to a station, press and hold a preset button until sound returns. 13. Scan: Press for a brief sampling of radio stations or CD tracks. Press again to stop. 14. Seek:[...]

FORD DUAL MEDIA SOUND SYSTEM (IF EQUIPPED) 1. / T une: Press to manually go up or down the radio frequency . Also use in menu mode to select various settings. 2. Seek: Press to access the next strong station or track. 3. Phone/mute: Press to mute the playing media. Press again to return to the playing media. 4. Menu: Press to toggle through the fol[...]

Balance: Press to adjust the audio between the left and right speakers. Use / / SEEK, SEEK . Fade: Press to adjust the audio between the front and rear speakers. Use / / SEEK, SEEK . Speed sensitive volume: Radio volume automatically changes slightly with vehicle speed to compensate for road and wind noise. Use / / SEEK, SEEK to adjust. Autoset: Al[...]

10. Repeat: Press to repeat the current CD track. 11. Fast forward: Press to manually advance in a tape or CD track. 12. Rewind: Press to manually reverse in a tape or CD track. 13. Memory presets: T o set a station: Select frequency band AM/FM; tune to a station, press and hold a preset button until sound returns. 14. Cassette door : Insert a tape[...]

21. Seek: Press to access the previous strong station or track. 22. Scan: Press for a brief sampling of radio stations or CD tracks. Press again to stop. PREMIUM/AUDIOPHILE IN-DASH SIX CD/MP3 SOUND SYSTEM (IF EQUIPPED) 1. / T une/Disc selector: Press to manually go up or down the radio frequency or to select a desired disc. Also use in menu mode to[...]

3. Menu: Press to toggle through the following modes: Autoset: Allows you to set the strongest local radio stations without losing your original manually set preset stations for AM/FM1/FM2 . Use // , SEEK to turn on/off. When the six strongest stations are filled, the station stored in preset 1 will begin playing. If there are less than six strong [...]

Compression: A vailable only in CD mode, compression brings soft and loud CD passages together for a more consistent listening level. Repeat: A vailable only in CD mode. Press to repeat the current CD track. RDS (A vailable on Audiophile radios only): RDS is available in FM mode, and allows you to search RDS-equipped stations for a certain category[...]

9. FOLDER: press to access the previous folder on MP3 discs, if folders are available. 10. Fast forward: Press to manually advance in a CD track. 11. Rewind: Press to manually reverse in a CD track. 12. Memory presets: T o set a station: Select frequency band AM/FM; tune to a station, press and hold a preset button until sound returns. 13. Scan: Pr[...]

19. CD eject: Press to eject a CD. Press and hold to auto eject all CDs present in the system. If there is no CD present, the display will read NO CD. 20. CD slot: Insert a CD label side up. FAMILY ENTERTAINMENT SYSTEM (IF EQUIPPED) Y our vehicle may be equipped with a Family Entertainment System (FES). Refer to the DVD Supplement Guide for further[...]

• Clean the cassette player head with a cassette cleaning cartridge after 10–12 hours of play to maintain good sound/operation. Don’t: • Expose tapes to direct sunlight, extreme humidity , heat or cold. • Leave tapes in the cassette player for a long time when not being played. CD/CD PLAYER CARE Do: • Handle discs by their edges only . [...]

HEATER ONLY SYSTEM (IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. T emperature selection: Controls the temperature of the airflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief description on each control. : Distributes outs[...]

T o aid in side window defogging/demisting in cold weather: 1. Select . 2. Adjust the temperature control to maintain comfort. 3. Set the fan speed to the highest setting. 4. Direct the outer instrument panel vents towards the side windows. T o increase airflow to the outer instrument panel vents, close the vents located in the middle of the instru[...]

: Distributes air through the windshield defroster vents and floor vents. : Distributes outside air through the windshield defroster vents. 3. R Rear defroster (if equipped): Press to defrost the rear window . Refer to Rear window defroster (if equipped) later in this chapter for more information. Heated mirrors (if equipped): Press to activate/dea[...]

• For maximum cooling performance (Max A/C): Max A/C mode: • Move the temperature control to the coolest setting. • Set the fan to the highest speed initially , then adjust to maintain comfort. Panel ( ) and panel/floor ( ) modes: • Move the temperature control to the coolest setting. • Select A/C and recirculated air ( ). Use recirculate[...]

AUTOMATIC T EMPERATURE CONTROL (A TC) SYSTEM (IF EQUIPPED) T emperature conversion: T o switch between Fahrenheit and Celsius: If your vehicle is equipped with a full message center , refer to Setup menu in the Message center section of the Driver Controls chapter for more information. If your vehicle is equipped with a mini message center , see yo[...]

1. Defrost : Distributes outside air through the windshield defroster vents and demister vents. Can be used to clear the windshield of fog and thin ice. 2. Fan speed control: Press to manually increase or decrease the fan speed. T o return to automatic fan operation, press AUTO. 3. A. R Rear defroster: Press to defrost the rear window . Refer to Re[...]

Automatic T emperature Control (A TC) system with heated seats (if equipped) T emperature conversion: T o switch between Fahrenheit and Celsius: If your vehicle is equipped with a full message center , refer to Units (Fahrenheit/Celsius) in the Driver Controls chapter . If your vehicle is equipped with a mini message center , refer to Mini message [...]

MAX A/C: For maximum cooling performance, press , A/C, , and set the temperature to 60°F and the highest blower setting. 1. Defrost : Distributes outside air through the windshield defroster vents and demister vents. Can be used to clear the windshield of fog and thin ice. 2. Fan speed control: Press to manually increase or decrease the fan speed.[...]

12. A/C control: Press to activate/deactivate air conditioning. Use with recirculated air to improve cooling performance and efficiency . Engages automatically in AUTO, (defrost) and (floor/defrost). 13. OFF: Outside air is shut out and the fan will not operate. 14. T emperature control: Press to increase/decrease the temperature in the vehicle cab[...]

5. Direct the outer instrument panel vents towards the side windows. T o increase airflow to the outer instrument panel vents, close the vents located in the middle of the instrument panel. Do not place objects on top of the instrument panel as these objects may become projectiles in a collision or sudden stop. REAR WINDOW DEFROSTER (IF EQUIPPED) R[...]

HEADLAMP CONTROL Rotate the headlamp control clockwise to the first position to turn on the parking lamps. Rotate clockwise to the second position to also turn on the headlamps. Autolamp control (if equipped) The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control. The[...]

Foglamp control (if equipped) The headlamp control also operates the foglamps. The foglamps can be turned on only when the headlamp control is in the , or position and the high beams are not turned on. Pull headlamp control towards you to turn foglamps on. The foglamp indicator light will illuminate if the ignition is in the ON position. Daytime ru[...]

Flash to pass Pull toward you slightly to activate and release to deactivate. P ANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel and all applicable switches in the vehicle during headlamp and parklamp operation. Move the control to the full upright position, past detent, to turn on the interior lamps. Move the control to the[...]

3. T urn on the low beam headlamps to illuminate the wall or screen and open the hood. Cover one of the headlamps so no light hits the wall. 4. On the wall or screen you will observe a light pattern with a distinct horizontal edge towards the right. If this edge is not at the horizontal reference line, the beam will need to be adjusted so the edge [...]

INTERIOR LAMPS Map lamps T o turn on the map lamps, press the control next to each lamp. Rear dome lamp (if equipped) The dome lamp lights when the control is in the DOOR (left) position, any door is open, the instrument panel switch is pushed past the detent and when any of the remote entry controls are pressed while the ignition is off. The rear [...]

Dome/courtesy lamps (if equipped) The dome lamp lights when: • any door is opened. • the instrument panel dimmer switch is rotated up until the courtesy lamps come on. • any of the remote entry controls are pressed and the ignition is OFF . The reading portion, the two outer lights, can only be toggled on and off at the lamp. Courtesy/reading[...]

Using the right bulbs Replacement bulbs are specified in the chart below . Headlamp bulbs must be marked with an authorized “D.O.T .” for North America and an “E” for Europe to assure lamp performance, light brightness and pattern and safe visibility . The correct bulbs will not damage the lamp assembly or void the lamp assembly warranty an[...]

2. At the top and inboard side of the headlamp, peel the protective cover back from the lower screws and loosen the three retaining screws. 3. Once the three retaining screws have been removed, disengage the tab at the top center of the headlamp assembly by lifting it up. 4. Slide headlamp assembly forward disconnecting the snap attachment at the f[...]

Replacing front parking lamp/turn signal/sidemarker bulbs 1. Make sure the headlamp control is in the OFF position and open the hood. 2. At the top and inboard side of the headlamp, peel the protective cover back from the lower screws and loosen the three retaining screws. 3. Once the three retaining screws have been removed, disengage the tab at t[...]

3. Carefully pull the lamp assembly straight rearward from the tailgate pillar to disengage two hidden snap-in retainers. (Flare side tail lamps are not equipped with snap-in retainers.) 4. Remove bulb socket from the lamp assembly by turning it counterclockwise. 5. Pull bulb straight out of socket and press in the new bulb. Install the new bulb(s)[...]

Replacing exterior mounted mirror turn signal indicator lamp bulbs For bulb replacement, see your authorized dealer . Replacing license plate lamp bulbs The license plate bulbs are located behind the rear bumper . T o change the license plate lamp bulbs: 1. Reach behind the rear bumper to locate the bulb. 2. T wist the bulb socket counterclockwise [...]

MULTI-FUNCTION LEVER W indshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers. W indshield washer: Push the end of the stalk: • briefly: causes a single swipe of the wipers without washer fluid. • a quick push and hold: the wipers will swipe three [...]

TILT STEERING WHEEL (IF EQUIPPED) Pull the lever down to unlock the steering column. While the lever is in the down position, tilt the steering column to its desired orientation. While holding the steering column, pull the lever up to its original position to lock the steering column. Never adjust the steering column when the vehicle is moving. ILL[...]

1. T o open the bins, move the center latch forward which will allow the door to be opened. 2. The latches on the side of the bins are to enable the user to remove the bin or add a dealer purchased feature. Sliding the bins on the rails may cause damage to the headliner . The removable bins are to be snapped into place not slid. Storage compartment[...]

Bin Removal Attach and remove bins from the rail using the following instructions: Place both palms on the underside of the storage bin, avoiding the storage bin door . Push upwards with palms. 2005 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus) Driver Controls 56[...]

While pushing upwards with palms, grip the side latches with fingers and squeeze. W ith pressure applied with palms and side latches squeezed down, pull downward on the entire storage bin and remove. AUXILIARY POWER POINT Power outlets are designed for accessory plugs only . Do not hang any type of accessory or accessory bracket from the plug. Impr[...]

Do not plug optional electrical accessories into the cigarette lighter . Use the power point. Do not use the power point for operating the cigarette lighter element. The maximum power each power point can supply depends on the fuse rating. For example: a 20A fuse should supply a maximum of 240 W atts, a 15A fuse should supply a maximum of 180 W att[...]

CELL PHONE USE The use of Mobile Communications Equipment has become increasingly important in the conduct of business and personal affairs. However , drivers must not compromise their own or others’ safety when using such equipment. Mobile Communications can enhance personal safety and security when appropriately used, particularly in emergency [...]

One touch down Allows the driver’ s window to open fully without holding the control down. Press completely down on the bottom part of the rocker switch and release quickly . Press the top part of the rocker switch to stop. Window lock (if equipped) The window lock feature allows only the driver to operate the power windows. T o lock out all the [...]

Accessory delay (if equipped) W ith accessory delay , the window switches may be used for up to ten minutes after the ignition switch is turned to the OFF position or until any door is opened. MIRRORS Automatic dimming inside rear view mirror (if equipped) Y our vehicle is equipped with an inside rear view mirror with an auto-dimming function. The [...]

Heated outside mirrors (if equipped) Heated mirrors remove ice, mist and fog. T o activate the heated mirrors, press the rear defrost button R located on the climate control panel. Refer to Rear Window Defrost in the Climate Controls chapter for more information. On vehicles not equipped with rear defrost, press the heated mirror control located on[...]

Fold-away mirrors Fold the side mirrors in carefully before driving through a narrow space, like an automatic car wash. If equipped with powerfold mirrors, you can fold the side mirrors using the power mirror switch. 1. Rotate the switch to the center/neutral position. 2. Momentarily pull the switch rearward to auto fold in. 3. Momentarily pull the[...]

The adjustment allows for approximately 3 inches (76 mm) of maximum travel. Never adjust the accelerator and brake pedal with feet on the pedals while the vehicle is moving. SPEED CONTROL (IF EQUIPPED) W ith speed control set, you can maintain a speed of 30 mph (48 km/h) or more without keeping your foot on the accelerator pedal. Speed control does[...]

Resuming a set speed Press the RES/RESUME control and release it. This will automatically return the vehicle to the previously set speed. The RES/RESUME control will not work if the vehicle speed is not faster than 30 mph (48 km/h). Increasing speed while using speed control There are two ways to set a higher speed: • Press and hold the SET contr[...]

• Depress the brake pedal until the desired vehicle speed is reached, press the SET control. Turning of f speed control There are two ways to turn off the speed control: • Depress the brake pedal or the clutch pedal (if equipped). This will not erase your vehicle’ s previously set speed, if RES/RESUME is then selected, the vehicle will return[...]

In any mode: • Press VOL + or − to adjust volume. Climate control features Press TEMP + or - to adjust temperature. Press F AN + or - to adjust fan speed. MOON ROOF (IF EQUIPPED) The moon roof control is located on the overhead console. Do not let children play with the moon roof or leave children unattended in the vehicle. They may seriously h[...]

T o open the moon roof: The moon roof is equipped with a one-touch open feature. Press and release the control. The moon roof will open to the “comfort” position. Press and release the control again to fully open. T o stop the one-touch open feature press either the or control again. T o close the moon roof: Press and hold the control until the[...]

Do not use the HomeLink 威 W ireless Control System with any garage door opener that lacks safety stop and reverse features as required by U.S. federal safety standards (this includes any garage door opener model manufactured before April 1, 1982). A garage door which cannot detect an object, signaling the door to stop and reverse, does not meet c[...]

3. Simultaneously press and hold both the HomeLink 威 and hand-held transmitter button. Do not release the buttons until Step 4 has been completed. Some entry gates and garage door openers may require you to replace Step 3 with procedures noted in the “Gate Operator and Canadian Programming” in this section for Canadian residents. 4. The indic[...]

Gate Operator & Canadian Programming During programming, your hand-held transmitter may automatically stop transmitting — not allowing enough time for HomeLink 威 to accept the signal from the hand-held transmitter . After completing Steps 1 and 2 outlined in the “Programming” section, replace Step 3 with the following: Note: If programm[...]

Erasing HomeLink 姞 buttons T o erase the three programmed buttons (individual buttons cannot be erased): • Press and hold the two outer HomeLink 威 buttons until the indicator light begins to flash-after 20 seconds. Release both buttons. Do not hold for longer that 30 seconds. HomeLink 威 is now in the train (or learning) mode and can be prog[...]

Selectable features Reset Press this control to select and reset functions shown in the INFO menu and SETUP menu. Info menu This control displays the following control displays: • Odometer/Compass • T rip odometer/Odometer/Compass • Distance to Empty • A verage Fuel Economy • T rip Elapsed Drive T ime Odometer/Trip odometer Refer to Gauge[...]

Compass zone/calibration adjustment 1. Determine your magnetic zone by referring to the zone map. 2. T urn ignition to the ON position. 3. Start the engine. 4. From Info menu, select the Compass/Odometer function. (Do not select T rip, DTE, or AFE. The top of the message center must be blank). 5. Press and hold the SETUP and RESET controls until th[...]

10. The compass is now calibrated. Distance to empty (DTE) Selecting this function from the INFO menu estimates approximately how far you can drive with the fuel remaining in your tank under normal driving conditions. Remember to turn the ignition OFF when refueling to allow this feature to correctly detect the added fuel. The DTE function will dis[...]

2. Record the highway fuel economy for future reference. It is important to press the RESET control after setting the speed control to get accurate highway fuel economy readings. Trip elapsed drive time Select this function from the INFO menu to display a timer . T o operate the T rip Elapsed Drive T ime perform the following: 1. Press and release [...]

3. OIL PRESSURE 4. BRAKE FLUID LEVEL 5. CHARGING SYSTEM Units (English/Metric) 1. Select this function from the SETUP menu for the current units to be displayed. 2. Press the RESET control to change from English to Metric. Autolocks This feature automatically locks all vehicle doors when the vehicle is shifted into any gear , putting the vehicle in[...]

Language 1. Select this function from the SETUP menu for the current language to be displayed. 2. Pressing the RESET control cycles the message center through each of the language choices. 3. Press and hold the RESET control to set the language choice. System warnings System warnings alert you to possible problems or malfunctions in your vehicle’[...]

W arning display Status Door ajar W arning can be reset Low fuel level W arning returns after 10 minutes Check charging system Low brake fluid level Low oil pressure Check engine temperature Reduced engine power Stop engine safely Check fuel cap W arning returns after the ignition key is turned from OFF to ON. Engine failsafe mode DOOR AJAR. Displa[...]

LOW BRAKE FLUID LEVEL. Indicates the brake fluid level is low and the brake system should be inspected immediately . Refer to Brake fluid reservoir in the Maintenance and Specifications chapter . LOW OIL PRESSURE. Displayed when the engine oil pressure is low . If this warning message is displayed, check the level of the engine oil. Refer to Engine[...]

Compass The compass reading may be affected when you drive near large buildings, bridges, power lines and powerful broadcast antennas. Magnetic or metallic objects placed in, on or near the vehicle may also affect compass accuracy . Usually , when something affects the compass readings, the compass will correct itself after a few days of operating [...]

Compass calibration adjustment Perform this adjustment in an open area free from steel structures and high voltage lines. For optimum calibration, turn off all electrical accessories (heater/air conditioning, wipers, etc.) and make sure all vehicle doors are shut. 1. Start the vehicle. 2. T o enter the compass calibration mode, press and hold the b[...]

5. Lift right side off of its hinge. 6. Lift tailgate to a 80–degree angle from horizontal. 7. Remove tailgate from left side hinge by sliding tailgate to the right. T o install, follow the removal procedures in reverse order . BED EXTENDER (IF EQUIPPED) Y our vehicle may be equipped with a bed extender designed to extend the pickup box for longe[...]

T o remove the bed extender: 1. Extend the bed extender . 2. Pull the round knobs on each side of the extender to unlock it. Make sure the locking clip screws are loose before removing the extender . 3. Press the locking clips below the middle bar on each side and lift the extender out of the bed. Note: Remove and store the bed extender when not in[...]

KEYS The key operates all locks on your vehicle. In case of loss, replacement keys are available from your dealer . Y ou should always carry a second key with you in a safe place in case you require it in an emergency . Refer to the SecuriLock 娂 passive anti-theft system section in this chapter for more information. POWER DOOR LOCKS (IF EQUIPPED)[...]

Childproof door locks (if equipped) • When these locks are set, the rear doors cannot be opened from the inside. • The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door . Setting the lock for one door will not automatica[...]

Y our vehicle is equipped with a remote entry system which allows you to: • unlock the vehicle doors without a key . • lock all the vehicle doors without a key . • activate the personal alarm. If there are problems with the remote entry system, make sure to take ALL remote entry transmitters with you to your authorized dealer in order to aid [...]

The (lock) and (unlock) features will work again after: • a door has become ajar , • the ignition is turned to the 3 (ON) position, or • using the UNLOCK control on your remote entry transmitter or unlocking via the keyless entry keypad. Deactivating/activating power door lock/unlock disable feature All vehicle doors must be closed before beg[...]

Activating the memory feature T o activate this feature: 1. Position the seat and adjustable pedals to the positions you desire. 2. Press the SET control on the driver’ s seat. 3. W ithin 5 five seconds, press one control on the remote transmitter and then press the 1 or 2 control on the driver’ s door panel to which you would like to associate[...]

2. Do not wipe off any grease on the battery terminals on the back surface of the circuit board. 3. Remove the old battery . Note: Please refer to local regulations when disposing of transmitter batteries. 4. Insert the new battery . Refer to the diagram inside the remote entry transmitter for the correct orientation of the battery . Press the batt[...]

T o program the transmitters yourself: • Unlock all doors using the power door lock/unlock control. Insert a key and turn the ignition from the 1 (OFF/LOCK) to the 3 (ON) position and cycle between 1 (OFF/LOCK) and 3 (ON) eight times in rapid succession (within 10 seconds) with the eighth turn ending in the 3 (ON) position. The locks will cycle t[...]

The dome lamp control (if equipped) must not be set to the off position for the illuminated entry system to operate. The inside lights will not turn off if: • they have been turned on with the dimmer control, or • any door is open. The battery saver will shut off the interior lamps 30 minutes after the last door is closed, even if the dimmer co[...]

4. W ithin five seconds, press the control two times. Note: One horn chirp should be heard, indicating the system has been disabled. Conversely , a horn chirp followed by a honk will indicate the system is enabled. Pressing the power door control two times again will turn the feature ON if it was previously OFF , or OFF if it was previously ON. Eve[...]

Power door unlock/lock procedure Y ou must complete Steps 1–5 within 30 seconds, or the procedure will have to be repeated. If the procedure needs to be repeated, you must wait a minimum of 30 seconds to begin again. 1. T urn the ignition to the 3 (ON) position, then press the control three times. 2. T urn the ignition to the 1 (OFF/LOCK) positio[...]

KEYLESS ENTRY SYSTEM (IF EQUIPPED) Y ou can use the keyless entry keypad to: • lock all vehicle doors. • unlock only the driver’ s door . • unlock all vehicle doors. • program/erase the customer keycode. • enable/disable the autolocking feature. The keypad can be operated with the factory set 5–digit entry code; this code is located o[...]

Antiscan feature The keyless entry keypad is equipped with an anti-theft function called “antiscan.” The antiscan feature provides a one-minute lockout feature, where the user is unable to enter the vehicle using the keypad; this lockout occurs when a valid entry code has not been entered by the user within 7 attempts (35 consecutive button pre[...]

Note: The SecuriLock 娂 passive anti-theft system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection. Note: Large metallic objects, electronic devices that are used to purchase gasoline or similar items, or a second coded key on the same k[...]

Automatic disarming Switching the ignition to the 3 (ON) position with a coded key disarms the vehicle. Replacement keys If your keys are lost or stolen and you don’t have an extra coded key , you will need to have your vehicle towed to an authorized dealer . The key codes need to be erased from your vehicle and new coded keys will need to be pro[...]

3. W ithin ten seconds of removing the first coded key , insert the second previously programmed coded key into the ignition and turn the ignition from the 1 (OFF/LOCK) position to the 3 (ON) position (maintain ignition in the 3 (ON) position for at least one second but no more than ten seconds). 4. T urn the ignition from the 3 (ON) position back [...]

SEATING Notes: Reclining the seatback can cause an occupant to slide under the seat’ s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop. Before returning the seatback to its original position, make sure that cargo [...]

Push control to lower head restraint. Front seat • Lift the track release bar to move the seat forward or rearward. Make sure that the seat is relatched into place. • Pull the release lever handle located on the side of the seat up to move the seat back forward or backward. Using the armrest (if equipped) Push the release control to move the ar[...]

Using the manual lumbar support For more lumbar support, turn the lumbar support control toward the front of vehicle. For less lumbar support, turn the lumbar support control toward the rear of vehicle. Adjusting the front power seat (if equipped) Never adjust the driver’ s seat or seatback when the vehicle is moving. Do not pile cargo higher tha[...]

Press the control to move the seat forward, backward, up or down. Memory seats/adjustable pedals (if equipped) This system allows automatic positioning of the driver seat and adjustable pedals to two programmable positions. The memory seat control is located on the driver’ s seat. • T o program position one, move the driver seat, and adjustable[...]

REAR SEATS Head restraints The purpose of these head restraints is to help limit head motion in the event of a rear collision. T o properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible. The head restraints can be moved up and down. Lift the head restrai[...]

1. Pull control to release seat cushion. 2. Rotate seat cushion up until it locks into vertical storage position. Returning the seat to seating position Before returning the seatback to its original position, make sure that cargo or any objects are not trapped underneath the seatback. After returning the seatback to its original position, pull on t[...]

• Restraints Control Module (RCM) with impact and safing sensors. • Restraint system warning light and back-up tone. • The electrical wiring for the airbags, crash sensor(s), safety belt pretensioners, front safety belt usage sensors, driver seat position sensor , and indicator lights. How does the Personal Safety System 姟 work? The Persona[...]

Front passenger sensing system For airbags to do their job they must inflate with great force, and this force can pose a potentially deadly risk to occupants that are very close to the airbag when it begins to inflate. For some occupants, like infants in rear -facing child seats, this occurs because they are initially sitting very close to the airb[...]

Front outboard safety belt pretensioners The safety belt pretensioners are designed to tighten the safety belts firmly against the occupant’ s body during a collision. This maximizes the effectiveness of the safety belts and helps properly position the occupant relative to the airbag to improve protection. The safety belt pretensioners can be eit[...]

Safety restraints precautions Always drive and ride with your seatback upright and the lap belt snug and low across the hips. T o reduce the risk of injury , make sure children sit in the back seat where they can be properly restrained. Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect th[...]

Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints. Safety belts and seats can become hot in a vehicle that has been closed up in sunny weather; they could burn a small child. Check seat covers and buckles before you place a child anywhere near them. Combination lap and shoulder be[...]

Center front safety belt (Regular Cab center seating position only) Always use both lap and shoulder safety belt in the Regular Cab center seating position. If you carry large cargo behind the seat or items that might damage or soil the belt, detach the belt from the seat: 1. Release the mini-buckle by inserting a key or safety belt tongue into the[...]

If the belt has been disconnected to carry large objects behind the seat, reconnect it as follows: 1. Remove the belt from the stowage clip on the back panel. 2. Buckle the small tongue on the end of the belt into the mini-buckle on the driver’ s side. The belt is now ready for use. This mini-buckle should stay buckled at all times unless cargo-c[...]

1. T o lengthen the lap belt, pull some webbing out of the shoulder belt retractor . 2. While holding the webbing below the tongue, grasp the tip (metal portion) of the tongue so that it is parallel to the webbing and slide the tongue upward. 3. Provide enough lap belt length so that the tongue can reach the buckle. How to fasten the cinch tongue ([...]

Energy management retractors Y our vehicle has a seat belt system equipped with energy management retractors at the driver and front outboard passenger seating positions. An energy management retractor is a device which pays out webbing in a controlled manner . This feature is designed to help further reduce the risk of force-related injuries to th[...]

How to use the automatic locking mode 1. Buckle the combination lap and shoulder belt. • Right front passenger seat • Rear seats (if equipped) 2. Grasp the shoulder portion and pull downward until the entire belt is extracted. 3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is n[...]

How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode. After any vehicle collision, the safety belt systems at all outboard seating positions (except the driver position, which doe[...]

Failure to replace the safety belt assembly under the above conditions could result in severe personal injuries in the event of a collision. Safety belt usage sensors The driver and front outboard passenger safety belt buckles are equipped with sensors that detect if the safety belts are fastened. The sensors provide information to the Personal Saf[...]

Lap belts Adjusting the lap belt The lap belt should fit snugly and as low as possible around the hips, not across the waist. The front center lap belt tongue is designed to fit only in the correct buckle. The tongue will not securely latch if you attempt to use it in any of the outboard seating position buckles. T o ensure that you have used the c[...]

Safety belt warning light and indicator chime The safety belt warning light illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts. Conditions of operation If... Then... The driver’ s safety belt is not buckled before the ignition switch is turned to the ON position... The safety belt warning[...]

If... Then... The driver’ s and front passenger’ s safety belts are buckled before the ignition switch is turned to the ON position or less than 1-2 minutes have elapsed since the ignition switch has been turned ON... The BeltMinder 娂 feature will not activate. The driver’ s or front passenger’ s safety belt is not buckled when the vehicl[...]

The following are reasons most often given for not wearing safety belts: (All statistics based on U.S. data) Reasons given... Consider ... “Crashes are rare events” 36700 crashes occur every day . The more we drive, the more we are exposed to “rare” events, even for good drivers. 1i n4o fu sw i l lb e seriously injured in a crash during our[...]

Reasons given... Consider ... “I have an airbag” Airbags offer greater protection when used with safety belts. Frontal airbags are not designed to inflate in rear and side crashes or rollovers. “I’d rather be thrown clear” Not a good idea. People who are ejected are 40 times more likely to DIE. Safety belts help prevent ejection, WE CAN?[...]

T o reduce the risk of injury , do not deactivate/activate the Belt Minder feature while driving the vehicle. 1. T urn the ignition switch to the RUN (or ON) position. (DO NOT ST ART THE ENGINE) 2. W ait until the safety belt warning light turns off. (Approximately 1 minute) • Step 3 must be completed within 50 seconds after the safety belt warni[...]

Safety belt maintenance Inspect the safety belt systems periodically to make sure they work properly and are not damaged. Inspect the safety belts to make sure there are no nicks, tears or cuts. Replace if necessary . All safety belt assemblies, including retractors, buckles, front safety belt buckle assemblies, buckle support assemblies (slide bar[...]

safety belts in impacts for which the airbags are designed to deploy , and airbags do not offer any protection in crashes for which they do not deploy . The airbag supplemental restraint system consists of: • driver and passenger dual stage airbag modules (which include the inflators and airbags). • one or more impact and safing sensors. • th[...]

The National Highway T raffic Safety Administration (NHTSA) recommends a minimum distance of at least 10 inches (25 cm) between an occupant’ s chest and the driver airbag cover . Never place your arms or feet over the airbag module as a deploying airbag can result in serious fractures or other injuries. T o properly position yourself away from th[...]

Additional equipment may affect the performance of the airbag sensors increasing the risk of injury . Please refer to the Body Builders Layout Book for instructions about the appropriate installation of additional equipment. Children and airbags For additional important safety information, read all information on safety restraints in this guide. Ch[...]

How does the airbag supplemental restraint system work? The airbag SRS is designed to activate when the vehicle sustains sufficient longitudinal deceleration. The fact that the airbags did not inflate in a collision does not mean that something is wrong with the system. Rather , it means the forces were not of the type sufficient to cause activatio[...]

If the airbag has deployed, the airbag will not function again and must be replaced immediately . If the airbag is not replaced, the unrepaired area will increase the risk of injury in a collision. Determining if the system is operational The SRS uses readiness lights in the instrument cluster or a tone to indicate the condition of the system. Refe[...]

The front passenger sensing system is designed to meet the regulatory requirements of Federal Motor V ehicle Safety Standard (FMVSS) 208 and is designed to turn off the front passenger’ s frontal airbag if: • the front passenger seat is unoccupied, or has small/medium objects in the front seat, • the system determines that an infant is presen[...]

If a person of adult-size is sitting in the front passenger’ s seat, but the “passenger airbag off” or “pass airbag off” indicator is lit, it could be that the person isn’t sitting properly in the seat. If this happens, turn the vehicle off and ask the person to place the seatback in the full upright position, then sit upright in the se[...]

In case there is a problem with the passenger sensing system, the airbag readiness light in the instrument cluster will stay lit. Do NOT attempt to repair or service the system; take your vehicle immediately to the an authorized dealer . The front passenger airbag is not designed to offer protection to an occupant in the center front seating positi[...]

Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. Always follow the instructions and warnings that come with any infant or child restraint you might use. Children and safety belts If the child is the proper size, restrain the child in a safety seat. C[...]

Booster seats should be used until you can answer YES to ALL of these questions: • Can the child sit all the way back against the vehicle seat back with knees bent comfortably at the edge of the seat without slouching? • Does the lap belt rest low across the hips? • Is the shoulder belt centered on the shoulder and chest? • Can the child st[...]

Both can be used in any vehicle in a seating position equipped with lap/shoulder belts if your child is over 40 lb. (18 kg). The shoulder belt should cross the chest, resting snugly on the center of the shoulder . The lap belt should rest low and snug across the hips, never up high across the stomach. If the booster seat slides on the vehicle seat,[...]

When installing a child safety seat: • Review and follow the information presented in the Airbag Supplemental Restraint System section in this chapter . • Use the correct safety belt buckle for that seating position (the buckle closest to the direction the tongue is coming from). • Insert the belt tongue into the proper buckle until you hear [...]

Installing child safety seats with combination lap and shoulder belts Airbags can kill or injure a child in a child seat. NEVER place a rear -facing child seat in front of an active airbag. If you must use a forward-facing child seat in the front seat, move the seat all the way back. Children 12 and under should be properly restrained in the rear s[...]

3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating position until y[...]

7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat. 8. Allow the safety belt to retract to remove any slack in the belt. 9. Before placing the child in the seat, forcibly move the seat forward and back to make sure the seat is securely held in pla[...]

1. Position the child safety seat in the Regular Cab center front seat. 2. If the center lap/shoulder safety belt has been disconnected from the seat to carry large cargo behind the seat, reconnect it by buckling the small buckle on the end of the belt into the mini-buckle on the driver’ s side. Airbags can kill or injure a child in a child seat.[...]

4. While holding both shoulder and lap portions next to the tongue, route the tongue and webbing through the child seat according to the child seat manufacturer’ s instructions. Be sure that the belt webbing is not twisted. 5. Insert the belt tongue into the proper buckle for that seating positions until you hear a snap and feel it latch. Make su[...]

8. Before placing the child into the child seat, forcibly pull the child seat forward and back to make sure that the seat is held securely in place. T o check this, grab the seat at the belt path and attempt to move it side to side and forward and back. There should be no more than one inch of movement for proper installation. 9. Check from time to[...]

7. Before placing the child into the child seat, forcibly tilt the child seat from side to side and in forward direction to make sure that the seat is held securely in place. If the child seat moves excessively , repeat Steps 5 through 7, try a different child safety seat, or properly install the child seat in a different position. Attaching child [...]

• F150 SuperCrew and SuperCab Front seat tether strap attachment 1. Position the child safety seat on the seat cushion. 2. Route the child safety seat tether strap over the back of the seat and under the head restraint. 3. Locate the correct anchor for the selected seating position. • Y ou may need to pull the seatback forward to access the tet[...]

• Front seat Regular Cab center (located on back panel) If the tether strap is clipped incorrectly , the child safety seat may not be retained properly in the event of a collision. 5. Install the child safety seat tightly using the LA TCH anchors or safety belts. Follow the instructions in this chapter . 6. T ighten the child safety seat tether s[...]

Rear seat tether strap attachment There are three loops of webbing just above the back of the rear seat (along the bottom edge of the rear window) in the SuperCab and SuperCrew . These loops are to be used as both routing loops and anchor loops for up to three child safety seat tether straps. For example, the center loop can be used as a routing lo[...]

3. Install the child safety seat tightly using the LA TCH anchors or safety belts. Follow the instructions in this chapter . 4. T ighten the tether strap according to the child seat manufacturer’ s instructions. Attaching safety seats with LA TCH (Lower Anchors and T ethers for Children) attachments for child seat anchors Some child safety seats [...]

Never attach two LA TCH child safety seats to the same anchor . In a crash, one anchor may not be strong enough to hold two child safety seat attachments and may break, causing serious injury or death. The lower anchors for child seat installation are located at the rear section of the seat between the cushion and seat back. The LA TCH anchors are [...]

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handle differently than passenger cars in the various driving conditions that are encountered on streets, highways and off-road. Utility vehicles and trucks are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to per[...]

Power is supplied to all four wheels through a transfer case or power transfer unit. 4WD vehicles allow you to select different drive modes as necessary . Information on transfer case operation and shifting procedures can be found in the Driving chapter . Information on transfer case maintenance can be found in the Maintenance and Specifications ch[...]

• Narrower — to provide greater maneuverability in tight spaces, particularly in off-road use. As a result of the above dimensional differences, SUV’ s and trucks often will have a higher center of gravity and a greater difference in center of gravity between the loaded and unloaded condition. These differences that make your vehicle so versa[...]

T readwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the ac[...]

TIRES T ires are designed to give many thousands of miles of service, but they must be maintained in order to get the maximum benefit from them. Glossary of tire terminology • T ire label: A label showing the OE (Original Equipment) tire sizes, recommended inflation pressure and the maximum weight the vehicle can carry . • T ire Identification [...]

INSPECTING AND INFLATING Y OUR TIRES Safe operation of your vehicle requires that your tires are properly inflated. Remember that a tire can lose up to half of its air pressure without appearing flat. Every day before you drive, check your tires. If one looks lower than the others, use a tire gauge to check pressure of all tires and adjust if requi[...]

Under -inflation is the most common cause of tire failures and may result in severe tire cracking, tread separation or ⬙ blowout ⬙ , with unexpected loss of vehicle control and increased risk of injury . Under -inflation increases sidewall flexing and rolling resistance, resulting in heat buildup and internal damage to the tire. It also may res[...]

when you get to the pump. It is normal for tires to heat up and the air pressure inside to go up as you drive. Never “bleed” or reduce air pressure when tires are hot. 2. Remove the cap from the valve on one tire, then firmly press the tire gauge onto the valve and measure the pressure with the tire gauge. 3. Add enough air to reach the recomme[...]

Important: Remember to replace the spare tire when you replace the road tires on your vehicle. Even if it has never been used, the spare tire should be replaced because tires degrade over time. Important: Remember to replace the wheel air valves when the road tires are replaced on your vehicle. CHANGING THE TIRES If you get a flat tire while drivin[...]

Use of a temporary emergency spare tire at any one wheel location can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • W inter weather driving capability • W et weather driving capability Location of the spare tire and tools The spare tire and [...]

2. Fully insert the jack handle through the bumper hole and into the guide tube through the access hole in the rear bumper . 3. T urn the handle counterclockwise until tire is lowered to the ground, the tire can be slid rearward and the cable is slightly slack. 4. Slide the retainer through the center of the wheel. Tire change procedure T o help pr[...]

3. Block the diagonally opposite wheel. 4. Obtain the spare tire and jack from their storage locations. 5. Use the tip of the lug wrench to remove any wheel trim. 6. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. 7. Position the jack according to the following guides and tur[...]

• Rear T o lessen the risk of personal injury , do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire. • Never use the front or rear differential as a jacking point. 8. Remove the lug nuts with the lug wrench. 9. Replace th[...]

• Seven lug nut wheel 12. Stow the flat tire. Refer to Stowing the flat/spare tire. 13. Stow the jack and lug wrench. Make sure the jack is fastened so it does not rattle when you drive. 14. Unblock the wheels. Stowing the flat/spare tire Note: Failure to follow spare tire stowage instructions may result in failure of cable or loss of spare tire.[...]

5. Repeat this tightness check procedure when servicing the spare tire pressure (every six months, as per your scheduled maintenance information), or at any time that the spare tire is disturbed through service of other components. 6. If removed, install the spare tire lock (if equipped) into the bumper drive tube with the spare tire lock key (if e[...]

Information on “P” type tires P215/65R15 95H is an example of a tire size, load index and speed rating. The definitions of these items are listed below . (Note that the tire size, load index and speed rating for your vehicle may be different from this example.) 1. P: Indicates a tire, designated by the T ire and Rim Association (T&RA), that[...]

7. H: Indicates the tire’ s speed rating. The speed rating denotes the speed at which a tire is designed to be driven for extended periods of time under a standard condition of load and inflation pressure. The tires on your vehicle may operate at different conditions for load and inflation pressure. These speed ratings may need to be adjusted for[...]

10. T ire Ply Composition and Material Used: Indicates the number of plies or the number of layers of rubber -coated fabric in the tire tread and sidewall. T ire manufacturers also must indicate the ply materials in the tire and the sidewall, which include steel, nylon, polyester , and others. 11. Maximum Load: Indicates the maximum load in kilogra[...]

Additional information contained on the tire sidewall for “L T” type tires “L T” type tires have some additional information beyond those of “P” type tires; these differences are described below: 1. LT: Indicates a tire, designated by the T ire and Rim Association (T&RA), that is intended for service on light trucks. 2. Load Range/L[...]

Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example. 1. T: Indicates a type of tire, designated by the T ire and Rim A[...]

Tire wear Measure and inspect the tire tread on all your tires periodically . Advanced and unusual tire wear can reduce the ability of tread to grip the road in adverse (wet, snowy , etc.) conditions. Visually check your tires for uneven wear , looking for high and low areas or unusually smooth areas. Also check for signs of tire damage. When the t[...]

Safety practices Driving habits have a great deal to do with your tire mileage and safety . • Observe posted speed limits • A void fast starts, stops and turns • A void potholes and objects on the road • Do not run over curbs or hit the tire against a curb when parking If your vehicle is stuck in snow , mud, sand, etc., do not rapidly spin [...]

Tire rotation Rotating your tires at the recommended interval (as indicated in the scheduled maintenance information that comes with your vehicle) will help your tires wear more evenly , providing better tire performance and longer tire life. Unless otherwise specified, rotate the tires approximately every 5,000 miles (8,000 km). • Rear Wheel Dri[...]

SNOW TIRES AND CHAINS Snow tires must be the same size and grade as the tires you currently have on your vehicle. The tires on your vehicle have all weather treads to provide traction in rain and snow . However , in some climates, you may need to use snow tires and chains. If you need to use chains, it is recommended that steel wheels (of the same [...]

V ehicle Curb W eight – is the weight of your new vehicle when you picked it up from your authorized dealer plus any aftermarket equipment. Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be found on the T ire Label on the B-Pillar or the edge of the driver’ s doo[...]

Example only: Cargo W eight – includes all weight added to the Base Curb W eight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight. 2005 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus) Tires, Wheels and Loading 174[...]

GA W (Gross Axle W eight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. GA WR (Gross Axle W eight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label located on the B-Pi[...]

GVWR (Gross V ehicle W eight Rating) – is the maximum allowable weight of the fully loaded vehicle (including all options, equipment, passengers and cargo). The GVWR is shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’ s door . The GVW must never exceed the GVWR. Exceeding the Safety Complianc[...]

Maximum Loaded T railer W eight – is the highest possible weight of a fully loaded trailer the vehicle can tow . It assumes a vehicle with only mandatory options, no cargo (internal or external), a tongue load of 10–15% (conventional trailer) or king pin weight of 15–25% (fifth wheel trailer), and driver only (150 lb. [68 kg]). Consult your a[...]

5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. 6. If your vehicle will be towing a trailer , load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the avail[...]

Special loading instructions for owners of pickup trucks and utility-type vehicles For important information regarding safe operation of this type of vehicle, see the Preparing to drive your vehicle section in the Driving chapter of this Owner’ s Guide . Loaded vehicles may handle differently than unloaded vehicles. Extra precautions, such as slo[...]

Regular Cab 4x2 (126” wheelbase) Engine Rear axle ratio Maximum GCWR-lb. (kg) Maximum trailer weight-lb. (kg) 4.2L (with manual transmission) 3.31 7200 (3266) 2400 (1089) 3.55 8500 (3856) 3700 (1678) 4.2L (with automatic transmission) 3.55 10000 (4536) 5100 (2313) 3.73 10500 (4763) 5600 (2540) 4.6L 3.55 11500 (5216) 6500 (2948) 4.6L 3.73 12000 (5[...]

Regular Cab 4x4 (126” wheelbase) Engine Rear axle ratio Maximum GCWR-lb. (kg) Maximum trailer weight-lb. (kg) 4.6L 3.55 11500 (5216) 6200 (2812) 4.6L 3.73 12000 (5443) 6700 (3039) 5.4L (with 17” tires) 3.55 13000 (5897) 7600 (3447) 5.4L (with 18” tires) 3.55 12500 (5670) 7100 (3221) 5.4L (with 17” tires) 3.73 13500 (6123) 8100 (3674) 5.4L ([...]

SuperCab 4x2 (133” wheelbase) Engine Rear axle ratio Maximum GCWR-lb. (kg) Maximum trailer weight-lb. (kg) 4.6L 3.55 11500 (5216) 6300 (2858) 4.6L 3.73 12000 (5443) 6800 (3084) 5.4L (with 17” tires) 3.55 13000 (5897) 7600 (3447) 5.4L (with 18” tires) 3.55 12500 (5670) 7100 (3220) 5.4L (with 17” tires) 3.73 13500 (6123) 8100 (3674) 5.4L (wit[...]

SuperCab 4x4 (133” wheelbase) Engine Rear axle ratio Maximum GCWR-lb. (kg) Maximum trailer weight-lb. (kg) 4.6L 3.55 11500 (5216) 6000 (2722) 4.6L 3.73 12000 (5443) 6500 (2948) 5.4L (with 17” tires) 3.55 13000 (5897) 7300 (3311) 5.4L (with 18” tires) 3.55 12500 (5670) 6800 (3084) 5.4L (with 17” tires) 3.73 13500 (6123) 7800 (3538) 5.4L (wit[...]

Crew Cab 4x2 (139” wheelbase) Engine Rear axle ratio Maximum GCWR-lb. (kg) Maximum trailer weight-lb. (kg) 4.6L 3.55 11700 (5307) 6300 (2858) 4.6L 3.73 12200 (5534) 6800 (3084) 5.4L (with 17” tires) 3.55 14000 (6350) 8500 (3856) 5.4L (with 18” tires) 3.55 13500 (6123) 8000 (3629) 5.4L (with 17” tires) 3.73 15000 (6804) 9500 (4309) 5.4L (wit[...]

Preparing to tow Use the proper equipment for towing a trailer and make sure it is properly attached to your vehicle. See your authorized dealer or a reliable trailer dealer if you require assistance. Hitches Do not use hitches that clamp onto the vehicle’ s bumper or attach to the axle. Y ou must distribute the load in your trailer so that 10%?[...]

Do not connect a trailer’ s hydraulic brake system directly to your vehicle’ s brake system. Y our vehicle may not have enough braking power and your chances of having a collision greatly increase. The braking system of the tow vehicle is rated for operation at the GVWR not GCWR. T railer lamps T railer lamps are required on most towed vehicles[...]

• Allow more distance for stopping with a trailer attached. • The trailer tongue weight should be 10–15% of the loaded trailer weight. • After you have traveled 50 miles (80 km), thoroughly check your hitch, electrical connections and trailer wheel lug nuts. • T o aid in engine/transmission cooling and A/C efficiency during hot weather wh[...]

• Place the transfer case lever in N (Neutral). • Do not exceed 55 mph (88 km/h) vehicle speed. • The maximum recommended distance is unlimited. • The vehicle must be towed in the forward position to ensure no damage is done to the internal transfer case components. The transfer case N (Neutral) position overrides the transmission and puts [...]

STARTING Positions of the ignition 1. OFF/LOCK, locks the steering wheel, automatic transmission gearshift lever and allows key removal. Note: The ignition key cannot be removed from the ignition unless the gearshift lever is securely latched in P (Park). 2. ACCESSORY , allows the electrical accessories such as the radio to operate while the engine[...]

Do not park, idle, or drive your vehicle in dry grass or other dry ground cover . The emission system heats up the engine compartment and exhaust system, which can start a fire. Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the engine. See Guarding a[...]

If starting a vehicle with an automatic transmission: • Make sure the gearshift is in P (Park). • Make sure the parking brake is set. If starting a vehicle with a manual transmission: • Make sure the parking brake is set. • Push the clutch pedal to the floor BRAKE 2005 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus) Driving 191[...]

3. T urn the key to 3 (ON) without turning the key to 4 (ST ART). 2005 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus) Driving 192[...]

Make sure the corresponding lights illuminate or illuminate briefly . If a light fails to illuminate, have the vehicle serviced. • If the driver’ s safety belt is fastened, the light may not illuminate. Starting the engine 1. T urn the key to 3 (ON) without turning the key to 4 (ST ART). If there is difficulty in turning the key , rotate the st[...]

Note: If the engine does not start within five seconds on the first try , turn the key to OFF , wait 10 seconds and try again. If the engine still fails to start, press and hold the accelerator to the floor and try again; this will allow the engine to crank with the fuel shut off in case the engine is flooded with fuel. Using the engine block heate[...]

Base instrument cluster with and without tachometer Mid and Luxury instrument cluster Four-wheel anti-lock brake system (ABS) Y our vehicle is equipped with an Anti-lock Braking System (ABS). This system helps you maintain steering control during emergency stops by keeping the brakes from locking. Noise from the ABS pump motor and brake pedal pulsa[...]

Base instrument cluster with and without tachometer Mid and Luxury instrument cluster Parking brake T o set the parking brake (1), press the parking brake pedal down until the pedal stops. The BRAKE warning lamp will illuminate and will remain illuminated until the parking brake is released. Base instrument cluster with and without tachometer Mid a[...]

STEERING T o prevent damage to the power steering system: • Never hold the steering wheel at its furthest turning points (until it stops) for more than a few seconds when the engine is running. • Do not operate the vehicle with a low power steering pump reservoir fluid level (below the MIN mark on the reservoir). If the power steering system br[...]

V ehicles with a higher center of gravity such as utility and four -wheel drive vehicles handle differently than vehicles with a lower center of gravity . Utility and four -wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road[...]

3. Remove the access plug using a flat head screwdriver , then push the override button using a flat head screwdriver , apply the brake pedal and shift the transmission into N (Neutral). 4. Reinstall the access plug cover , start the vehicle and release the parking brake. Do not drive your vehicle until you verify that the brakelamps are working. A[...]

2. Open the center console bin. Using a screwdriver , carefully pry off the console finish panel surrounding the shifter mechanism by inserting a screwdriver into the latch slot as shown. 3. Remove console finish panel assembly to expose the inside of the gearshift. 4. Press and hold the white button located along side the shifter housing assembly [...]

If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly . See your authorized dealer . Understanding the gearshift positions of the 4–speed automatic transmission Y our vehicle’ s automatic transmission is equipped with a special shift strategy that insures maximum heater pe[...]

T o put your vehicle in P (Park): • Come to a complete stop • Move the gearshift lever and securely latch it in P (Park) Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn the ignition to the LOCK position and remove the key whenever you leave your vehicle. R (Reverse) W ith the gearshift lever in R (Re[...]

• Floor -shift transmission The transmission control indicator (TCIL) will illuminate on the instrument cluster . Drive (not shown) Drive is activated when the transmission control switch is pressed. • This position allows for all forward gears except overdrive. • O/D OFF lamp is illuminated. • Provides engine braking. • Use when driving [...]

1 (First) • Provides maximum engine braking. • Allows upshifts by moving gearshift lever . • W ill not downshift into 1 (First) at high speeds; allows for 1 (First) when vehicle reaches slower speeds. Forced downshifts • Allowed in D (Overdrive) or Drive. • Depress the accelerator to the floor . • Allows transmission to select an approp[...]

4. Move the gearshift lever to 1st gear , then slowly release the clutch pedal while slowly pressing on the accelerator . During each shift, the clutch pedal must be fully depressed to the floor . Failure to fully depress the clutch pedal to the floor may cause increased shift efforts, prematurely wear transmission components or damage the transmis[...]

Maximum downshift speeds 1 Shift from: T ransfer case position (if equipped) 2H or 4H 4L D (Overdrive) - 4 55 mph (89 km/h) 21 mph (34 km/h) 4 - 3 45 mph (72 km/h) 17 mph (27 km/h) 3 - 2 35 mph (56 km/h) 13 mph (21 km/h) 2 - 1 20 mph (32 km/h) 7 mph (11 km/h) 1 Downshift at lower speeds when driving on slippery surfaces. Reverse 1. Make sure that y[...]

Removing the key T urn the ignition off, push the release lever (located above the ignition), then turn the key toward you and remove the key . REVERSE SENSING SYSTEM (IF EQUIPPED) The Reverse Sensing System (RSS) sounds a tone to warn the driver of obstacles near the rear bumper when the R (Reverse) is selected and the vehicle is moving at speeds [...]

The RSS detects obstacles up to 6 feet (2 meters) from the rear bumper with a decreased coverage area at the outer corners of the bumper , (refer to the figures for approximate zone coverage areas). As you move closer to the obstacle, the rate of the tone increases. When the obstacle is less than 10 inches (25.0 cm) away , the tone will sound conti[...]

If your vehicle sustains damage to the rear bumper/fascia, leaving it misaligned or bent, the sensing zone may be altered causing inaccurate measurement of obstacles or false alarms. FOUR-WHEEL DRIVE (4WD) OPERATION (IF EQUIPPED) For important information regarding safe operation of this type of vehicle, see Preparing to drive your vehicle in this [...]

N (Neutral) – No power to either front or rear wheels. 4L (4WD Low) – Uses extra gearing to provide maximum power to all four wheels at reduced speeds. Intended only for off-road applications such as deep sand, steep grades or pulling heavy objects. 4L (4WD Low) will not engage while the vehicle is moving above 3 mph (5 km/h); this is normal an[...]

Do not leave the vehicle unattended with the transfer case in the N (Neutral) position. Always set the parking brake fully and turn off the ignition when leaving the vehicle. Using the electronic shift 4WD system (if equipped) 2H (2WD High) - Power to the rear wheels only; used for street and highway driving. Provides optimal smoothness and fuel ec[...]

3. On vehicles equipped with an automatic transmission, place the transmission in N (Neutral); on vehicles equipped with a manual transmission, depress the clutch. 4. Move the 4WD control to the desired position. • If shifting into 4L (4WD Low), wait for the 4X4 LOW light in the instrument cluster to turn on indicating the shift is complete. • [...]

If your vehicle goes off the edge of the pavement • If your vehicle goes off the edge of the pavement, slow down, but avoid severe brake application, ease the vehicle back onto the pavement only after reducing your speed. Do not turn the steering wheel too sharply while returning to the road surface. • It may be safer to stay on the apron or sh[...]

Emergency maneuvers • In an unavoidable emergency situation where a sudden sharp turn must be made, remember to avoid “over -driving” your vehicle, i.e., turn the steering wheel only as rapidly and as far as required to avoid the emergency . Excessive steering will result in less vehicle control, not more. Additionally , smooth variations of [...]

If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly . See your authorized dealer . 4WD Systems 4WD (when you select a 4WD mode) uses all four wheels to power the vehicle. This increases traction, enabling you to drive over terrain and road conditions that a conventional two-[...]

Mud and water If you must drive through high water , drive slowly . T raction or brake capability may be limited. When driving through water , determine the depth; avoid water higher than the bottom of the hubs (if possible) and proceed slowly . If the ignition system gets wet, the vehicle may stall. Once through water , always try the brakes. W et[...]

Driving on hilly or sloping terrain Although natural obstacles may make it necessary to travel diagonally up or down a hill or steep incline, you should always try to drive straight up or straight down. A void driving crosswise or turning on steep slopes or hills . A danger lies in losing traction, slipping sideways and possibly rolling over . When[...]

Driving on snow and ice 4WD vehicles have advantages over 2WD vehicles in snow and ice but can skid like any other vehicle. Should you start to slide while driving on snowy or icy roads, turn the steering wheel in the direction of the slide until you regain control. A void sudden applications of power and quick changes of direction on snow and ice.[...]

DRIVING THROUGH WATER If driving through deep or standing water is unavoidable, proceed very slowly especially when the depth is not known. Never drive through water that is higher than the bottom of the hubs (for trucks) or the bottom of the wheel rims (for cars). When driving through water , traction or brake capability may be limited. Also, wate[...]

• Rear ballast weight behind the rear axle may be required to prevent exceeding the FGA WR, and provide front-to-rear weight balance for proper braking and steering. • Front wheel toe may require re-adjustment to prevent premature uneven tire wear . Specifications are found in the Ford W orkshop Manual. • Headlight aim may require re-adjustme[...]

Never remove or defeat the “tripping mechanisms” designed into the snow removal equipment by its manufacturer . Doing so may cause damage to the vehicle and the snow removal equipment as well as possible air bag deployment. Do not attempt to service, repair , or modify the air bag supplemental restraint system (SRS) or its fuses. See your Ford [...]

GETTING ROADSIDE ASSISTANCE T o fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New V ehicle Limited W arranty . The service is available: • 24–hours, seven days a week • for the New V ehicle Limited W arranty period of three years or [...]

Canadian customers who require roadside assistance, call 1–800–665–2006. If you need to arrange roadside assistance for yourself, Ford Motor Company will reimburse a reasonable amount. T o obtain reimbursement information, U.S. Ford or Mercury vehicles customers call 1-800-241-3673; Lincoln vehicle customers call 1–800–521–4140. Canadia[...]

This switch is located in the front passenger’ s footwell, behind the kick panel access cover , to the left of the fuse box. The access cover needs to be removed to reset the fuel pump shut-off switch. T o reset the switch: 1. T urn the ignition OFF . 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset the switch by pushing in [...]

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A T an T an — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Y ellow Y ellow Y ellow Blu[...]

The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 10A* Run/Accessory - W ipers, Instrument cluster , Audio for XL/STX 2 20A* Stop/T urn lamps, Brake on/off switch 3 5A* Power mirrors, Memory seats and pedals 4 10A* DVD battery power , Power fold mirror 5 7.5A* Keep alive memory for Po[...]

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 10 20A* T railer tow back-up lamps relay (PCB1), T railer tow parklamp relay (R201) 11 10A* A/C clutch, 4x4 solenoid 12 — Not used 13 10A* Climate control module power , Flasher relay 14 10A* Back-up lamp and Daytime Running Lamps (DRL) relay coil, A/C pressure switc[...]

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 27 5A* Passenger Air bag Deactivation (P AD) warning lamp, Cluster air bag warning lamp, Cluster RUN /ST ART power 28 5A* SecuriLock transceiver (P A TS) 29 15A* PCM 4x4 power 30 15A* PCM 4x4 power 31 20A* Radio power 32 15A* V apor Management V alve (VMV), A/C clutch [...]

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 103 20A** ABS valves 104 — Not used 105 30A** Electric trailer brakes 106 30A** T railer tow battery charge 107 30A** Power door locks (BSM) 108 30A** Passenger power seat 109 30A** Driver power seat, Adjustable pedals 110 — Not used 111 30A** 4x4 relays 112 40A** [...]

Auxiliary relay box The relay box is located in the engine compartment on the left fender . • W ith Daytime Running Lamp (DRL) and 4x4 options • W ithout Daytime Running Lamp (DRL) and 4x4 options The relays are coded as follows: Fuse/Relay Location Fuse Amp Rating Description F03 5A Clockspring illumination R01 Full ISO Relay 4x4 CCW R02 Full [...]

JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Batteries contain sulfuric acid which can burn skin, eyes and clothing, if contacted. Do not attempt to push-start your vehicle. Automatic transmissions do not have push-start ca[...]

Connecting the jumper cables 1. Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery . Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery . 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery . + – + – + ?[...]

3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery . 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’ s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding [...]

Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables. Removing the jumper cables Remove the jumper cables in the rev[...]

3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery . After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle c[...]

WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member of a roadside assistance program, your roadside assistance service provider . Ford recommends your vehicle be towed with a wheel lift or flatbed. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing pr[...]

GETTING THE SERVICES YOU NEED At home Y ou must take your Ford vehicle to an authorized dealer for warranty repairs. While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction. Please note that certain warranty repair[...]

In Canada: Customer Relationship Centre Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) www .ford.ca If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the authorized dealer could provide, after following the steps described above, c[...]

In some states (in the U.S.) you must directly notify Ford in writing before pursuing remedies under your state’ s warranty laws. Ford is also allowed a final repair attempt in some states. In the United States, a warranty dispute must be submitted to the Dispute Settlement Board before taking action under the Magnuson-Moss W arranty Act, or to t[...]

THE DISPUTE SETTLEMENT BOARD (U.S. ONLY) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes. • available free to owners and lessees of qualifying Ford Motor Company vehicles. The Dispute Settlement Board may not be available in all states. Ford Motor Company reserves the right to change elig[...]

Board membership The Board consists of: • Three consumer representatives • An authorized dealer representative Consumer candidates for Board membership are recruited and trained by an independent consulting firm. The dealership Board member is chosen from authorized dealer management, recognized for their business leadership qualities. What the[...]

Oral presentations If you would like to make an oral presentation, indicate YES to question 6 on the application. While it is your right to make an oral presentation before the Board, this is not a requirement and the Board will decide the case whether or not an oral presentation is made. An oral presentation may be requested by the Board as well. [...]

UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those cases where you continue to feel that the efforts by Ford of Canada and the authorized dealer to resolve a factory-related vehicle service concern have been unsatisfactory , Ford of Canada participates in an impartial third part[...]

If you did not take advantage of the Ford Extended Service Plan at the time of purchasing your vehicle, you may still be eligible. Since this information is subject to change, please ask your authorized dealer for complete details about Ford Extended Service Plan coverage options, or visit the Ford ESP website at www .ford-esp.com. GETTING ASSIST A[...]

ORDERING ADDITIONAL OWNER’S LITERA TURE T o order the publications in this portfolio, contact Helm, Incorporated at: HELM, INCORPORA TED P .O. Box 07150 Detroit, Michigan 48207 Or call: For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website: w[...]

W ASHING THE EXTERIOR W ash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail W ash (ZC-3–A), which is available from your authorized dealer . • Never use strong household detergents or soap, such as dish washing or laundry liquid. These products can discolor and spot painted surfaces. • Ne[...]

• Do not allow paint sealant to come in contact with any non-body (low-gloss black) colored trim, such as grained door handles, roof racks, bumpers, side moldings, mirror housings or the windshield cowl area. The paint sealant will “gray” or stain the parts over time. PAINT CHIPS Y our authorized dealer has touch-up paint and sprays to match [...]

• Spray Motorcraft Engine Shampoo and Degreaser (ZC-20) on all parts that require cleaning and pressure rinse clean. • Cover the highlighted areas to prevent water damage when cleaning the engine. • 4.2L engine • 4.6L engine 2005 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus) Cleaning 248[...]

• 5.4L engine • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your authorized dealer . • For routine cleaning, use Motorcraft Detail W ash (ZC-3–A). • If tar[...]

• Do not use abrasives, as they may cause scratches. • Do not use fuel, kerosene, or paint thinner to clean any parts. • W iper blades can be cleaned with isopropyl (rubbing) alcohol or windshield washer solution. Be sure to replace wiper blades when they appear worn or do not function properly . Do not use sharp objects, such as a razor blad[...]

• If a ring forms on the fabric after spot cleaning, clean the entire area immediately (but do not oversaturate) or the ring will set. • Do not use household cleaning products or glass cleaners, which can stain and discolor the fabric and affect the flame retardant abilities of the seat materials. Do not use cleaning solvents, bleach or dye on [...]

First use a dry cloth then wipe with a damp cloth. Allow the area to dry , then apply conditioner . • Clean spills as quickly as possible. • T est any cleaner or stain remover on an inconspicuous part of the leather as cleaners may darken the leather . For more specific cleaning information, contact the King Ranch Saddle Shop at 1–800–282?[...]

quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle. Each product is made from high quality materials that meet or exceed rigid specifications. For best results, use the following products or products of equivalent quality: Motorcraft Bu[...]

SERVICE RECOMMENDATIONS T o help you service your vehicle: • W e highlight do-it-yourself items in the engine compartment for easy location. • W e provide scheduled maintenance information which makes tracking routine service easy . If your vehicle requires professional service, your authorized dealer can provide the necessary parts and service[...]

2. Block the wheels. • Manual transmission: 1. Set the parking brake, depress the clutch and place the gearshift in N (Neutral). 2. Block the wheels. Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the b[...]

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.2L V6 engine 1. Battery 2. Clutch fluid reservoir (manual transmission) 3. Power steering fluid reservoir 4. Brake fluid reservoir 5. Engine coolant reservoir 6. Air filter assembly 7. Engine oil filler cap 8. Engine oil dipstick 9. T ransmission fluid dipstick (automatic transmission) 10. W indshi[...]

4.6L V8 1. Battery 2. T ransmission fluid dipstick (automatic transmission) 3. Engine oil filler cap 4. Power steering fluid reservoir 5. Engine oil dipstick 6. Brake fluid reservoir 7. Engine coolant reservoir 8. Air filter assembly 9. W indshield washer fluid reservoir 2005 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus) Maintenance and Specif[...]

5.4L V8 1. Battery 2. T ransmission fluid dipstick (automatic transmission) 3. Air filter assembly 4. Power steering fluid reservoir 5. Engine oil dipstick 6. Brake fluid reservoir 7. Engine coolant reservoir 8. Engine oil filler cap 9. W indshield washer fluid reservoir 2005 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus) Maintenance and Specif[...]

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low . In very cold weather , do not fill the reservoir completely . Only use a washer fluid that meets Ford specification WSB-M8B16–A2. Do not use any special washer fluid such as windshield water repellent type fluid or bug wash. They may cause squeaking, chatter noise, stre[...]

4. Open the hood. Protect yourself from engine heat. • 4.2L V6 engine • 4.6L/5.4L V8 engine 5. Locate and carefully remove the engine oil level indicator (dipstick). MAX MIN 2005 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus) Maintenance and Specifications 260[...]

6. W ipe the indicator clean. Insert the indicator fully , then remove it again. • If the oil level is between the lower and upper holes or between the MIN and MAX marks (depending on application), the oil level is acceptable. DO NOT ADD OIL. • 4.2L V6 engine • 4.6L/5.4L V8 engine • If the oil level is below the lower hole or the MIN mark, [...]

Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter . 2. If the engine oil level is not within the normal range, add only certified engine oil of the recommended viscosity . Remove the engine oil filler cap and use a funnel to pour the engine oil into the opening. 3. Recheck the engine oil l[...]

Change your engine oil and filter according to the appropriate schedule listed in scheduled maintenance information. Ford production and aftermarket (Motorcraft) oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, start-up engine noises o[...]

Batteries normally produce explosive gases which can cause personal injury . Therefore, do not allow flames, sparks or lighted substances to come near the battery . When working near the battery , always shield your face and protect your eyes. Always provide proper ventilation. When lifting a plastic-cased battery , excessive pressure on the end wa[...]

• If you do not allow the engine to relearn its idle trim, the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned. If the battery has been disconnected or a new battery has been installed, the clock and the preset radio stations must be reset once the battery is reconnected. • Always dispose of au[...]

When the engine is cold, check the level of the engine coolant in the reservoir . • The engine coolant should be at the “FULL COLD” level or within the “COLD FILL RANGE” as listed on the engine coolant reservoir (depending upon application). • Refer to scheduled maintenance information for service interval schedules. • Be sure to read[...]

Do not add engine coolant when the engine is hot. Steam and scalding liquids released from a hot cooling system can burn you badly . Also, you can be burned if you spill coolant on hot engine parts. Do not put engine coolant in the windshield washer fluid container . If sprayed on the windshield, engine coolant could make it difficult to see throug[...]

T o reduce the risk of personal injury , make sure the engine is cool before unscrewing the coolant pressure relief cap. The cooling system is under pressure; steam and hot liquid can come out forcefully when the cap is loosened slightly . 1. Before you begin, turn the engine off and let it cool. 2. When the engine is cool, wrap a thick cloth aroun[...]

Coolant refill capacity T o find out how much fluid your vehicle’ s cooling system can hold, refer to Refill capacities in this section. Fill your engine coolant reservoir as outlined in Adding engine coolant in this section. Severe climates If you drive in extremely cold climates (less than –34° F [–36° C ]): • It may be necessary to inc[...]

How fail-safe cooling works If the engine begins to overheat: • The engine coolant temperature gauge will move to the red (hot) area. • The mini message center (if equipped) will indicate “Check Gauges”, refer to W arning Lights and Chimes in the Instrument Cluster chapter . • The message center (if equipped) will indicate a system warnin[...]

Never remove the coolant reservoir cap while the engine is running or hot. 5. Restart the engine and take your vehicle to a service facility . Driving the vehicle without repairing the engine problem increases the chance of engine damage. T ake your vehicle to a service facility as soon as possible. WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Impor[...]

Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before refueling your vehicle. • Always turn off the vehicle before refueling. • Automotive fuels can be harmful or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injur[...]

Refueling Fuel vapor burns violently and a fuel fire can cause severe injuries. T o help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • T urn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; • Keep sparks, flames and smoking materials away [...]

If the Digital Display reads “CHECK FUEL CAP” and stays on after you start the engine, the fuel filler cap may not be properly installed. T urn off the engine, remove the fuel filler cap, align the cap properly and reinstall it. If you must replace the fuel filler cap, replace it with a fuel filler cap that is designed for your vehicle. The cus[...]

Octane recommendations Y our vehicle is designed to use “Regular” unleaded gasoline with pump (R+M)/2 octane rating of 87. W e do not recommend the use of gasolines labeled as “Regular” that are sold with octane ratings of 86 or lower in high altitude areas. Do not be concerned if your engine sometimes knocks lightly . However , if it knock[...]

Running out of fuel A void running out of fuel because this situation may have an adverse effect on powertrain components. If you have run out of fuel: • Y ou may need to cycle the ignition from OFF to ON several times after refueling, to allow the fuel system to pump the fuel from the tank to the engine. • Y our Service engine soon indicator m[...]

The amount of usable fuel in the empty reserve varies and should not be relied upon to increase driving range. When refueling your vehicle after the fuel gauge indicates empty , you might not be able to refuel the full amount of the advertised capacity of the fuel tank due to the empty reserve still present in the tank. For consistent results when [...]

Driving style — good driving and fuel economy habits Give consideration to the lists that follow and you may be able to change a number of variables and improve your fuel economy . Habits • Smooth, moderate operation can yield up to 10% savings in fuel. • Steady speeds without stopping will usually give the best fuel economy . • Idling for [...]

Conditions • Heavily loading a vehicle or towing a trailer may reduce fuel economy at any speed. • Carrying unnecessary weight may reduce fuel economy (approximately 1 mpg [0.4 km/L] is lost for every 400 lb [180 kg] of weight carried). • Adding certain accessories to your vehicle (for example bug deflectors, rollbars/light bars, running boar[...]

• A void running out of fuel. • Do not turn off the ignition while your vehicle is moving, especially at high speeds. • Have the items listed in scheduled maintenance information performed according to the specified schedule. The scheduled maintenance items listed in scheduled maintenance information are essential to the life and performance [...]

government emission standards. The OBD-II system also assists your authorized dealer in properly servicing your vehicle. When the indicator illuminates, the OBD-II system has detected a malfunction. T emporary malfunctions may cause your indicator to illuminate. Examples are: 1. The vehicle has run out of fuel—the engine may misfire or run poorly[...]

POWER STEERING FLUID Check the power steering fluid. Refer to the scheduled maintenance information for the service interval schedules. If adding fluid is necessary , use only MERCON 威 A TF . 1. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indicator will be near the center of [...]

BRAKE FLUID The fluid level will drop slowly as the brakes wear , and will rise when the brake components are replaced. Fluid levels between the “MIN” and “MAX” lines are within the normal operating range; there is no need to add fluid. If the fluid levels are outside of the normal operating range the performance of your brake system could [...]

1. Clean the reservoir cap before removal to prevent dirt and water from entering the reservoir . 2. Remove cap and rubber diaphragm from reservoir . 3. Add fluid until the level reaches the step in the reservoir . 4. Reinstall rubber diaphragm and cap onto reservoir . T RANSMISSION FLUID Checking automatic transmission fluid (if equipped) Refer to[...]

3. W ith the parking brake engaged and your foot on the brake pedal, start the engine and move the gearshift lever through all of the gear ranges. Allow sufficient time for each gear to engage. 4. Latch the gearshift lever in P (Park) and leave the engine running. 5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. If necessary[...]

High fluid level Fluid levels above the safe range may result in transmission failure. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. High fluid levels can be caused by an overheating condition. Adjusting automatic transmission fluid levels Before adding any fluid, make sure the correc[...]

Checking and adding manual transmission fluid (if equipped) 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Fluid level should be at bottom of the opening. 4. Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening. 5. Install and tighten the fill plug securely . Use on[...]

T ransfer case fluid (if equipped) 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level. 3. Add only enough fluid through the filler opening so that the fluid level is at the bottom of the opening. Use only fluid that meets Ford specifications. Refer to Lubricant specifications in this chapter . DRIVELINE UNIVERSAL JOINT [...]

AIR FILTER Refer to scheduled maintenance information for the appropriate intervals for changing the air filter element. When changing the air filter element, use only the Motorcraft air filter element listed. Refer to Motorcraft part numbers in this chapter . Note: Do not start your engine with the air cleaner removed and do not remove it while th[...]

• 5.4L Engine 1. Release two retainer clamps. 2. Pull air filter tray assembly out toward front of vehicle and lift air filter element up and out of housing. The air filter box needs to be free of any debris before installing a new air filter . 3. Install a new air filter element into the tray assembly . 4. Return air filter tray to original posi[...]

MOTORCRAFT PART NUMBERS Component 4.2L V6 engine 4.6L V8 engine 5.4L V8 engine Air filter element F A-1632 F A-1632 F A-1754 Battery BTX-65-650 BTX-65-650 BTX-65-650 Fuel Filter FG-986-B FG-986-B FG-986-B Oil Filter FL-400-S FL-820-S FL-820-S PCV valve 1 Spark plugs 2 1 The PCV valve is a critical emission component. It is one of the items listed i[...]

REFILL CAPACITIES Fluid Ford Part Name Application Capacity Brake fluid and clutch fluid Motorcraft High Performance DOT 3 Motor V ehicle Brake Fluid All Fill to line or step (for clutch) on reservoir Engine coolant 1 Motorcraft Premium Gold Engine Coolant (yellow-colored) 4.2L V6 engine 17.6 quarts (16.7L) 4.6L V8 engine 20.7 quarts (19.6L) 5.4L V[...]

Fluid Ford Part Name Application Capacity Power steering fluid Motorcraft MERCON 威 AT F All Fill to between MIN and MAX lines on reservoir T ransfer case fluid Motorcraft MERCON 威 AT F 4x4 vehicles 2.0 quarts (1.9L) 2 T ransmission fluid 3 Motorcraft MERCON 威 AT F 5–speed manual 3.75 quarts (3.5L) Motorcraft MERCON 威 V AT F Automatic 4R70[...]

Some transmission fluids may be labeled as dual usage, such as MERCON 威 and MERCON 威 V . These dual usage fluids are not to be used in an automatic transmission that requires use of the MERCON 威 type fluid. However , these dual usage fluids may be used in transmissions that require the MERCON 威 V type fluid. MERCON 威 and MERCON 威 V type[...]

LUBRICANT SPECIFICATIONS Item Ford part name or equivalent Ford part number Ford specification Front axle (4X4) Motorcraft SAE 80W -90 Premium Rear Axle Lubricant XY -80W -90-QL WSP-M2C197–A Rear axle Motorcraft SAE 75W -140 High Performance Synthetic Rear Axle Lube 1 XY -75W140–QL WSL-M2C192–A Brake fluid and clutch fluid Motorcraft High Per[...]

Item Ford part name or equivalent Ford part number Ford specification Hinges, latches, striker plates, fuel filler door hinge and door check arm Motorcraft Silicone Brake Caliper Grease and Dielectric Compound XG-3-A ESE-M1C171–A Lock cylinders Motorcraft Penetrating and Lock Lubricant XL-1 none T ransmission /steering/parking brake linkages and [...]

correct type. Refer to your scheduled maintenance information to determine the correct service interval. Some transmission fluids may be labeled as dual usage, such as MERCON 威 and MERCON 威 V . These dual usage fluids are not to be used in an automatic transmission that requires use of the MERCON 威 type fluid. However , these dual usage fluid[...]

V EHICLE DIMENSIONS Regular Cab V ehicle dimensions Styleside 6.5’ box - inches (mm) Flareside 6.5’ box - inches (mm) Styleside 8.0’ box - inches (mm) (1) Overall length 211.2 (5364) 211.2 (5364) 229.8 (5837) (2) Overall width 78.9 (2005) 78.9 (2005) 78.9 (2005) (3) Overall height – 4x2/4x4 73.7 (1872) / 75.6 (1921) 73.8 (1875) / 75.6 (1921[...]

SuperCab V ehicle dimensions Styleside 5.5’ box - inches (mm) Styleside / Flareside 6.5’ box - inches (mm) Styleside 8.0’ box - inches (mm) (1) Overall length 217.8 (5532) 229.8 (5837) 248.4 (6309) (2) Overall width 78.9 (2005) 78.9 (2005) 78.9 (2005) (3) Overall height – 4x2/4x4 74.1 (1881) / 76.5 (1943) 73.5 (1866) / 75.6 (1919) 73.4 (186[...]

Super Crew V ehicle dimensions Styleside 5.5’ box - inches (mm) (1) Overall length 223.8 (5685) (2) Overall width 78.9 (2005) (3) Overall height – 4x2/4x4 73.5 (1867) / 76.0 (1931) 2005 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus) Maintenance and Specifications 300[...]

Super Crew V ehicle dimensions Styleside 5.5’ box - inches (mm) (4) Wheelbase – 4x2/4x4 138.5 (3518) / 138.5 (3518) (5) T rack - Front 67.0 (1701) (5) T rack - Rear 67.0 (1701) 2005 F-150 (f12) Owners Guide (post-2002-fmt) USA (fus) Maintenance and Specifications 301[...]

IDENTIFYING YOUR VEHICLE Certification label The National Highway T raffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located. The Safety Compliance Certification Label is located on the structure by the trailing [...]

The V ehicle Identification Number (VIN) contains the following information: 1. W orld manufacturer identifier 2. Brake type and Gross V ehicle W eight Rating (GVWR) 3. V ehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence number Engine number The engine number (the last eight numbers [...]

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for your vehicle through your local authorized Ford or Ford of Canada dealer . These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance [...]

Splash guards Step bars T onneau covers T ruck caps Wheels Interior style Electrochromatic compass/temperature interior mirrors Floor mats Leather wrapped steering wheels Scuff plates Speed control Lifestyle Bedliners and bedmats Bed tents Bike racks Cargo organization and management Rear seat entertainment systems T oolboxes T owing mirrors T rail[...]

For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to your vehicle, do not exceed the total weight capacity of the vehicle or of the front or rear axle (GVWR or GA WR as indicated on the Safety Compliance Certifi[...]

A Accessory delay .......................... 61 Air cleaner filter ...............289, 291 Air conditioning ....................36, 38 Airbag supplemental restraint system ................................ 124–125 and child safety seats ............ 127 description .............................. 125 disposal .................................... 12[...]

Climate control (see Air conditioning or Heating) ........................... 32, 36, 38 Clock adjust 6-CD in dash .............................27 AM/FM Stereo ........................... 19 AM/FM/CD ................................. 21 AM/FM/T ape/CD ....................... 24 Clutch fluid .......................................... 283 operation w[...]

Engine block heater ................. 194 Engine oil .................................. 259 checking and adding ..............259 dipstick .................................... 259 filter , specifications ........ 262, 291 recommendations ................... 262 refill capacities ........................ 292 specifications ..................295, 297[...]

I Ignition ....................... 189, 297–298 Infant seats (see Safety seats) ..................... 135 Inspection/maintenance (I/M) testing ........................................ 281 Instrument panel cleaning ................................... 250 cluster ........................................ 10 lighting up panel and interior ...........[...]

P Parking brake ............................ 196 Parts (see Motorcraft parts) ....291 Passenger Occupant Classification Sensor ................. 107 Power distribution box (see Fuses) ............................... 225 Power door locks ........................ 85 Power mirrors ............................. 61 Power point ..........................[...]

Speed control .............................. 64 Starting your vehicle ....... 189–190, 193 jump starting .......................... 231 Steering wheel controls ...................................... 66 tilting ......................................... 54 T T ailgate ........................................ 82 T emperature control (see Climate con[...]