Gigabyte GA-MA785GT-UD3H manual

GA-MA785GT -UD3H AM3 socket motherboard for AMD Phenom ™ II processor/AMD Athlon ™ II processor User's Manual Rev . 1 101 12ME-MA785T3-1 101R[...]

Motherboard GA-MA785GT -UD3H Jul. 8, 2009 Jul. 8, 2009 Motherboard GA-MA785GT-UD3H[...]

Copyright © 2009 GIGA-BYTE TECHNOLOGY CO., L TD. All rights reserved. The trademarks mentioned in this manual are legally registered to their respective owners. Disclaimer Information in this manual is protected by copyright laws and is the property of GIGABYTE. Changes to the specications and features in this manual may be made by GIGABYTE wit[...]

- 4 - T able of Contents Box Contents ................................................................................................................... 6 Optional Items ................................................................................................................. 6 GA-MA785GT -UD3H Motherboard Layout ...........................[...]

- 5 - Chapter 3 Drivers Installation ........................................................................................ 61 3-1 Installing Chipset Drivers ............................................................................... 61 3-2 Application Software ..................................................................................[...]

- 6 - Box Contents GA-MA785GT -UD3H motherboard Motherboard driver disk User's Manual Quick Installation Guide One IDE cable T wo SA T A 3Gb/s cables I/O Shield Optional Items Floppy disk drive cable (Part No. 12CF1-1FD001-7*R) 2-port USB 2.0 bracket (Part No. 12CR1-1UB030-5*R) 2-port IEEE 1394a bracket (Part No. 12CF1-1IE008-0*R) 2-port SA T [...]

- 7 - GA-MA785GT -UD3H Motherboard Layout KB_USB CPU_F AN Socket AM3 A TX GA-MA785GT -UD3H CD_IN F_AUDIO AUDIO LPT PCIEX4_1 PCIEX1_1 IDE DDR3_1 DDR3_3 DDR3_2 DDR3_4 BA TTERY F_P ANEL PWR_LED F_1394_1 COM IT8718 A TX_12V_2X4 AMD 785G AMD SB710 SA TA2_0 SA TA2_4 SA TA2_2 SA TA2_1 SA TA2_5 SA TA2_3 PCI1 PCI2 USB_1394 CODEC PWR_F AN SYS_F AN2 SYS_F AN1[...]

- 8 - Block Diagram PS/2 KB or Mouse Floppy LPT Port COM Port Hyper T ransport 3.0 AMD 785G AMD SB710 PCI Express Bus IT8718 CPU CLK+/- (200 MHz) GFX CLK (100 MHz) A T A-133/100/66/33 IDE Channel Dual BIOS 12 USB Ports LPC Bus DDR3 1666(O.C.)/1333/1066 MHz Dual Channel Memory Center/Subwoofer Speaker Out Line Out MIC Line In S/PDIF In S/PDIF Out Si[...]

- 9 - Hardware Installation 1- 1 Installation Precautions Th e m ot her bo ar d c on ta in s n um er ou s d el ic at e e le ct ro ni c c ir cu it s a nd comp one nt s w hi ch can become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read the user's manual and follow these procedures: • Prio r to ins[...]

Hardware Installation - 10 - 1- 2 Product Specications CPU  Support for AM3 processors: AMD Phenom ™ II processor/ AMD Athlon ™ II processor (Go to GIGABYTE's website for the latest CPU support list.) H yp e r T r an sp o rt B us  5200 MT/s Chipset    North Bridge: AMD 785G    South Bridge: AMD SB7[...]

- 1 1 - Hardware Installation IEEE 1394  T .I. TSB43AB23 chip  Up to 3 IEEE 1394a ports (1 on the back panel, 2 via the IEEE 1394a brackets connected to the internal IEEE 1394a headers) Internal  1 x 24-pin A TX main power connector Connectors  1 x 8-pin A TX 12V power connector  1 x oppy disk drive connector  1 x IDE connector[...]

Hardware Installation - 12 - (Note 1) Due to Windows 32-bit operating system limitation, when more than 4 GB of physical memory is installed, the actual memory size displayed will be less than 4 GB. (Note 2) The DVI-D port does not support D-Sub connection by adapter. (Note 3) Simultaneous output for DVI-D and HDMI is not supported. (Note 4) If you[...]

- 13 - Hardware Installation 1-3 Installing the CPU and C PU Cooler 1-3 -1 I nst all ing t he CPU A. Locate the pin one (denoted by a small triangle) of the CPU socket and the CPU. Read the following guidelines before you begin to install the CPU: • Make sure that the motherboard supports the CPU. (Go to GIGABYTE's website for the latest [...]

Hardware Installation - 14 - B. Follow the steps below to correctly install the CPU into the motherboard CPU socket. • Before installing the CPU, make sure to turn off the computer and unplug the power cord from the power outlet to prevent damage to the CPU. • Do not force the CPU into the CPU socket. The CPU cannot t in if oriented in[...]

- 15 - Hardware Installation 1-3 -2 I nst all ing t he CPU Cool er Follow the steps below to correctly install the CPU cooler on the CPU. (The following procedure uses the GIGABYTE cooler as the example.) Step 1: Apply an even and thin layer of thermal grease on the surface of the installed CPU. Step 2: Place the CPU cooler on the CPU. Step 3: Ho o[...]

Hardware Installation - 16 - 1- 4 Installin g the Me mor y DDR3_1 DDR3_2 DDR3_3 DDR3_4 If two memory modules are to be i nstalled, it is rec- ommended that you install them in the DDR3_1 and DDR3_2 sockets. Due to CPU limitations, read the following guidelines before installing the memory in Dual Channel mode. 1. Dual Channel mode cannot be enabled[...]

- 17 - Hardware Installation 1- 4 -2 Inst all ing a M emo r y Notch DDR3 DIMM A DDR3 memory module has a notch, so it can only t in one direction. Follow the steps below to correctly install your memory modules in the memory sockets. Step 1: Note the orienta tion of t he memo ry modul e. Sprea d the ret aining clips at both ends of the memory so[...]

Hardware Installation - 18 - 1-5 Installing an Expansion Card Read the following guidelines before you begin to install an expansion card: • Make sure the motherboard supports the expansion card. Carefully read the manual that came with your expansion card. • Always turn off the computer and unplug the power cord from the power outlet before in[...]

- 19 - Hardware Installation 1-6 Setup of the A TI Hybrid CrossFire X ™ Conguration Combining the onboard GPU with a discrete graphics card, A TI Hybrid CrossFireX can provide signicantly advanced display performance for AMD platform. This section give instructions on conguring an A TI Hybrid CrossFireX system. A. System Requirements - W[...]

Hardware Installation - 20 - 1- 7 Back Panel Con nectors USB Port The USB port supports the USB 2.0/1.1 specication. Use this port for USB devices such as a USB key - board/mouse, USB printer , USB ash drive and etc. PS/2 Keyboard or PS/2 Mouse Port Use this port to connect a PS/2 keyboard or PS/2 mouse. D-Sub Port The D-Sub port supports a 1[...]

- 21 - Hardware Installation Activity LED: State Description Blinking Data transmission or receiving is occurring Off N o dat a tr ansm iss ion or r ece ivin g is oc curr ing Connection/Speed LED: State Description Orange 1 Gbps data rate Green 100 Mbps data rate Off 10 Mbps data rate Activity LED Connection/ Speed LED LAN Port Optical S/PDIF Out C[...]

Hardware Installation - 22 - Center/Subwoofer Speaker Out Jack (Orange) Use this audio jack to connect center/subwoofer speakers in a 5.1/7.1-channel audio conguration. Rear Speaker Out Jack (Black) Use this audio jack to connect rear speakers in a 7.1-channel audio conguration. Side Speaker Out Jack (Gray) Use this audio jack to connect side[...]

- 23 - Hardware Installation 1-8 Internal Connec tors 1 5 3 2 8 19 7 9 11 4 18 6 12 14 10 4 16 13 15 17 20 1) A TX_12V_2X4 2) A TX 3) CPU_FAN 4) SYS_FAN1/SYS_F AN2 5) PWR_FAN 6) FDD 7) IDE 8) SA T A2_0/1/2/3/4/5 9) PWR_LED 10) BA TTERY 11) F_P ANEL 12) F_AUDIO 13) CD_IN 14) SPDIF_IO 15) F_USB1/F_USB2/F_USB3 16) F_1394_1/F_1394_2 17) LPT 18) COM 19)[...]

Hardware Installation - 24 - G.QBOFM A TX_12V_2X4: A TX_12V_2X4 4 1 8 5 G.QBOFM 13 1 24 12 A TX A TX: Pin No. Denition 13 3.3V 14 -12V 15 GND 16 PS_ON (soft On/Off) 17 GND 18 GND 19 GND 20 -5V 21 +5V 22 +5V 23 +5V (O nly for 2x12-pi n A TX) 24 GN D ( Only for 2 x12-p in A TX) Pin No. Denition 1 3.3V 2 3.3V 3 GND 4 +5V 5 GND 6 +5V 7 GND 8 Powe[...]

- 25 - Hardware Installation 3/4/5) CPU_F AN/SYS_F AN1/SYS_FAN2/PWR_F AN (Fan Headers) The motherbo ard has a 4-pi n CPU fan head er (CPU_FAN), a 3-pin (SYS_FAN2) and a 4-pin (SYS_ F AN1) system fan headers, and a 3-pin power fan header (PWR_FAN). Most fan headers possess a foolproof insertion design. When connecting a fan cable, be sure to connect[...]

Hardware Installation - 26 - 7) IDE (IDE Connector) The IDE connector supports up to two IDE devices such as hard drives and optical drives. Before attach- ing the IDE cable, locate the foolproof groove on the connector . If you wish to connect two IDE devices, remember to set the jumpers and t he cabling accord ing to the role of the IDE device s [...]

- 27 - Hardware Installation 9) PWR_LED (System Power LED Header) This h eader can be u sed to c onne ct a sys tem po wer LE D on the chass is to i ndica te sys tem po wer status. The LED is on when the system is operating. The LED keeps blinking when the system is in S1 sleep state. The LED is off when the system is in S3/S4 sleep state or powered[...]

Hardware Installation - 28 - 1 1) F_P ANEL (Front Panel Header) Connect the power switch, reset switch, speaker and system status indicator on the chassis front panel to this header according to the pin assignments below . Note the positive and negative pins before con- necting the cables. • PW (Power Switch, Red): Connects to the power switch on[...]

- 29 - Hardware Installation 12) F_AUDIO (Front Panel Audio Header) The front panel audio header supports Intel High Denition audio (HD) an d AC'97 audio. Y ou may connect your chassis front panel audio module to this header. Make sure the wire assignments of the module con - nector match the pin assignments of the motherboard header. Incor[...]

Hardware Installation - 30 - 14) SPDIF_IO (S/PDIF In/Out Header) This header supports digital S/PDIF In/Out. Via an optional S/PDIF In and Out cable, this header can connect to an audio device that supports digital audio out and an audio system that supports digital au- dio in. For purchasing the optional S/PDIF In and Out cable, please contact the[...]

- 31 - Hardware Installation 16) F_1394_1/F_1394_2 (IEEE 1394a Headers) The headers conform to IEEE 1394a specication. The IEEE 1394a header can provide one IEEE 1394a port via an optional IEEE 1394a bracket. For purchasing the optional IEEE 1394a bracket, please con- tact the local dealer . Pin No. Denition 1 TP A+ 2 TP A- 3 GND 4 GND 5 TPB+[...]

Hardware Installation - 32 - 19) CI (Chassis Intrusion Header) This motherboard provides a chassis detection feature that detects if the chassis cover has been re- moved. This function requires a chassis with chassis intrusion detection design. 18) COM (Serial Port Header) The COM header can provide one serial port via an optional COM port cable. F[...]

- 33 - Hardware Installation 20) CLR_CMOS (Clearing CMOS Jumper) Use this jumper to clear the CMOS values (e.g. date information and BIOS congurations) and reset the CMOS values to factory defaults. T o clear the CMOS values, place a jumper cap on the two pins to temporarily short the two pins or use a metal object like a screwdriver to touch th[...]

Hardware Installation - 34 -[...]

- 35 - BIOS Setup BIOS (Ba sic Inpu t and Out put Syst em) reco rds hard ware par ameters of the sy stem in t he CMOS o n the motherboard. Its major functions include conducting the Power-On Self-T est (POST) during system startup, saving sy stem param eters and l oading op erating sy stem, etc . BIOS incl udes a BIO S Setup pro gram that allows th[...]

BIOS Setup - 36 - 2-1 Startup Screen The following screens may appear when the computer boots. A. The LOGO Screen (Default) B. The POST Screen Function Keys: <T AB>: POST SCREEN Press the <T ab> key to show the BIOS POST screen. T o show the BIOS POST screen at system start- up, refer to the instructions on the Full Screen LOGO Show ite[...]

- 37 - BIOS Setup 2-2 The Main Menu Once you enter the BIOS Setup program, the Main Menu (as shown below) appears on the screen. Use ar- row keys to move among the items and press <Enter> to accept or enter a sub-menu. (Sample BIOS V ersion: E1) Main Menu Help The on-screen description of a highlighted setup option is displayed on the bottom [...]

BIOS Setup - 38 -  The Functions of the <F1 1> and <F12> keys (For the Main Menu Only)  F1 1: Save CMOS to BIOS This function allows you to save the current BIOS settings to a prole. Y ou can create up to 8 proles (Prole 1-8) and name each prole. First enter the prole name (to erase the default prole name, use[...]

- 39 - BIOS Setup 2-3 MB Intelligent T weaker(M.I.T .) • Whether the system will work stably with the overclock/overvoltage settings you made is depen - dent on your overall system congurations. Incorrectly doing overclock/overvoltage may result in damage to CPU, chipset, or memory and reduce the useful life of these components. This page is f[...]

BIOS Setup - 40 - CMOS Setup Utility-Copyright (C) 1984-2009 A ward Software Advanced Clock Calibration higf : Move Enter: Select +/-/PU/PD: V alue F10: Save ESC: Exit F1: General Help F5: Previous V alues F6: Fail-Safe Defaults F7: Optimized Defaults Item Help Menu Level  EC Firmware Selection [Normal] Advanced Clock Calibration [Disabled[...]

- 41 - BIOS Setup CPU Clock Ratio Allows you to alter the clock ratio for the installed CPU. The adjustable range is dependent on the CPU being used. CPU NorthBridge Freq. Allows you to alter the North Bridge controller frequency for the installed CPU. The adjustable range is dependent on the CPU being used. CPU Host Clock Control Enables or disabl[...]

BIOS Setup - 42 - DCT s Mode Allows you to set memory control mode. Ganged Sets memory control mode to single dual-channel. Unganged Sets memory control mode to two single-channel. (Default) DDR3 Timing Items Manual allows all DDR3 Timing items below to be congurable. Options are: Auto (default), Manual. CAS# latency Options are: Auto (default),[...]

- 43 - BIOS Setup T rfc3 for DIMM4 Options are: Auto (default), 90ns, 1 10ns, 160ns, 300ns, 350ns. Write Recovery Time Options are: Auto (default), 5T~8T , 10T , 12T . Precharge Time Options are: Auto (default), 4T~7T . Row Cycle Time Options are: Auto (default), 1 1T~42T . RAS to RAS Delay Options are: Auto (default), 4T~7T . Bank Interleaving Ena[...]

BIOS Setup - 44 - CPU V oltage Control Allows you to set the CPU voltage. Auto sets the CPU voltage as required. The adjustable range is de- pendent on the CPU being installed. (Default: Normal) Note: Increasing CPU voltage may result in damage to your CPU or reduce the useful life of the CPU. Normal CPU Vcore Displays the normal operating voltage [...]

- 45 - BIOS Setup Date (mm:dd:yy) Sets the system date. The date format is week (read-only), month, date and year . Select the desired eld and use the up arrow or down arrow key to set the date. Time (hh:mm:ss) Sets the system time. For example, 1 p.m. is 13:0:0. Select the desired eld and use the up arrow or down arrow key to set the time. I[...]

BIOS Setup - 46 - The following elds display your hard drive specications. If you wish to enter the parameters manually , refer to the information on the hard drive. Capacity Approximate capacity of the currently installed hard drive. Cylinder Number of cylinders. Head Number of heads. Precomp Write precompensation cylinder . Landing Zone Lan[...]

- 47 - BIOS Setup 2-5 Advanced BIOS Features Internal Graphics Mode Allows you to determine whether to allocate system memory for the onboard graphics controller . Disabled Disables the onboard graphics controller . UMA Allocates memory for the onboard graphics controller from the system memory . (Default) UMA Frame Buffer Size Frame buffer size is[...]

BIOS Setup - 48 - AMD K8 Cool&Quiet control Auto Lets the AMD Cool'n'Quiet driver dynamically adjust the CPU clock and VID to reduce heat output from your computer and its power consumption. (Default) Disabled Disables this function. Hard Disk Boot Priority Species the sequence of loading the operating system from the installed har[...]

- 49 - BIOS Setup 2-6 Integrated Peripherals OnChip IDE Channel Enables or disables the integrated IDE controller . (Default: Enabled) OnChip SA T A Controller Enables or disables the integrated SA T A controller . (Default: Enabled) OnChip SA T A T ype (SA T A2_0~SA T A2_3 connectors) Congures the operating mode of the integrated SA T A2_0~SA T[...]

BIOS Setup - 50 - This motherboard incorporates cable diagnostic feature designed to detect the status of the attached LAN cable. This feature will detect cabling issue and report the approximate distance to the fault or short. Refer to the following information for diagnosing your LAN cable: When No LAN Cable Is Attached... If no LAN cable is atta[...]

- 51 - BIOS Setup Onboard Audio Function Enables or disables the onboard audio function. (Default: Enabled) If you wish to install a 3rd party add-in audio card instead of using the onboard audio, set this item to Disabled . Onboard 1394 Function Enables or disables the onboard IEEE 1394 function. (Default: Enabled) OnChip USB Controller Enables or[...]

BIOS Setup - 52 - ACPI Suspend T ype Species the ACPI sleep state when the system enters suspend. S1(POS) Enables the system to enter the ACPI S1 (Power on Suspend) sleep state. In S1 sleep state, the system appears suspended and stays in a low power mode. The system can be resumed at any time. S3(STR) Enables the system to enter the ACPI S3 (Su[...]

- 53 - BIOS Setup (Note) Supported on Windows 7/Vista operating system only . PME Event Wake Up Allows the system to be awakened from an ACPI sleep state by a wake-up signal from a PCI or PCIe de- vice. Note: T o use this function, you need an A TX power supply providing at least 1A on the +5VSB lead. (Default: Enabled) HPET Support (Note) Enables [...]

BIOS Setup - 54 - PCI1 IRQ Assignment Auto BIOS auto-assigns IRQ to the rst PCI slot. (Default) 3,4,5,7,9,10,1 1,12,14,15 Assigns IRQ 3,4,5,7,9,10,1 1,12,14,15 to the rst PCI slot. PCI2 IRQ Assignment Auto BIOS auto-assigns IRQ to the second PCI slot. (Default) 3,4,5,7,9,10,1 1,12,14,15 Assigns IRQ 3,4,5,7,9,10,1 1,12,14,15 to the second PCI [...]

- 55 - BIOS Setup Hardware Thermal Control Enables or disables the CPU overheating protection function. When enabled, the CPU core voltage and ratio will be reduced when the CPU is overheated. (Default: Enabled) Reset Case Open Status Keeps or clears the record of previous chassis intrusion status. Enabled clears the record of previous chassis intr[...]

BIOS Setup - 56 - Current V oltage(V) Vcore/DDR3 1.5V/+3.3V/+12V Displays the current system voltages. Current System/CPU T emperature Displays current system/CPU temperature. Current CPU/SYSTEM/POWER F AN Speed (RPM) Displays current CPU/system/power fan speed. CPU Warning T emperature Se ts th e w ar n in g t hr es h ol d f or CP U t em pe r at u[...]

- 57 - BIOS Setup Press <Enter> on this item and then press the <Y> key to load the safest BIOS default settings. In case system instability occurs, you may try to load Fail-Safe defaults, which are the safest and most stable BIOS settings for the motherboard. 2-10 Load Fail-Safe Defaults CMOS Setup Utility-Copyright (C) 1984-2009 A war[...]

BIOS Setup - 58 - Press <Enter> on this item and type the password with up to 8 characters and then press <Enter>. Y ou will be requested to conrm the password. T ype the password again and press <Enter>. The BIOS Setup program allows you to specify two separate passwords: Supervisor Password When a system password is set and t[...]

- 59 - BIOS Setup Press <Enter> on this item and press the <Y> key . This saves the changes to the CMOS and exits the BIOS Setup program. Press <N> or <Esc> to return to the BIOS Setup Main Menu. 2-13 Save & Exit Setup Press <Enter> on this item and press the <Y> key. This exits the BIOS Setup without saving [...]

BIOS Setup - 60 -[...]

- 61 - Drivers Installation 3-1 Installing Chipset Drivers Chapter 3 Drivers Installation After inserting the driver disk, "Xpress Install" will automatically scan your system and then list all the drivers that are recommended to install. Y ou can click the Install All button and "Xpress Install" will install all the rec- ommend[...]

Drivers Installation - 62 - 3-2 Application Software This page displays all the utilities and applications that GIGABYTE develops and some free software. Y ou can click the Install button on the right of an item to install it. 3-3 T echnical Manuals This page provides GIGABYTE's application guides, content descriptions for this driver disk, an[...]

- 63 - Drivers Installation 3-4 Contact For the detailed contact information of the GIGABYTE T aiwan headquarter or worldwide branch ofces, click the URL on this page to link to the GIGABYTE website. 3-5 System This page provides the basic system information.[...]

Drivers Installation - 64 - 3-6 Download Center T o update the BI OS, drivers, or application s, click the Download Center button to link to the GIGABYTE website. The latest version of the BIOS, drivers, or applications will be displayed.[...]

- 65 - Unique Features 4-1 Xpress Recovery2 Chapter 4 Unique Features Xp r es s R e co v er y 2 i s a u ti l it y t h at a l l ow s y ou to q u i ck l y co m p re s s a nd back up your system data and perform restoration of it. Supporting NTFS, F A T32, and FA T16 le systems, Xpress Recovery2 can back up data on P A T A and SA T A hard drives an[...]

Unique Features - 66 - Step 3: Wh e n pa r ti t io n in g y o ur h a rd d r i ve , m ak e s ur e t o leave unallocated space (10 GB or more is recom- mended; actual size requirements vary , depending on the amount of data) and begin the installation of the operating system. Step 1: Select BACKUP to start backing up your hard drive data. Step 4: Aft[...]

- 67 - Unique Features D. Using the Restore Function in Xpress Recovery2 E. Removing the Backup F . Exiting Xpress Recovery2 Sel ec t RESTORE to re st or e th e ba ck up t o yo ur h ar d dr ive in case the system breaks down. The RESTORE option will not be present if no backup is created before. Select REBOOT to exit Xpress Recovery2. Step 2: After[...]

Unique Features - 68 - 4-2 BIOS Update Utilities GI GA B YT E m ot h er b oa r ds p r ov i de t w o un i qu e B IO S u pd a te t o ol s , Q- F la s h ™ an d @ BI O S ™ . GI G AB Y TE Q-Flash and @BIOS are easy-to-use and allow you to update the BIOS without the need to enter MS-DOS mod e. Ad dit ion all y , t his m oth erb oar d fe atu res t he[...]

- 69 - Unique Features B. Updating the BIOS When updatin g the BIOS, ch oose the loc ation where t he BIOS le is saved. The follow ing procedur e as - sumes that you save the BIOS le to a oppy disk. Step 1: 1. Insert the oppy disk containing the BIOS le into the oppy disk driv e. In the main menu of Q-Flash, use the up or down arr[...]

Unique Features - 70 - Step 4: Press <Esc> and then <Enter> to exit Q-Flash and reboot the system. As the system boots, you should see the new BIOS version is present on the POST screen. Step 5: During the POST , press <Delete> to enter BIOS Setup. Select Load Optimized Defaults and press <Enter> to load BIOS defaults. Syste[...]

- 71 - Unique Features 4-2-2 Updating the BIOS with the @BIOS Utility A. Before Y ou Begin 1. In Windows, close all applications and TSR (T erminate and Stay Resident) programs. This helps prevent unexpected failures when performing a BIOS update. 2. During t he BIOS u pdate pr ocess, e nsure t he Inter net conn ection i s stabl e and do NO T inter[...]

Unique Features - 72 - Available functions in EasyTune 6 may differ by motherboard model. Grayed-out area(s) indicates that the item is not congurable or the function is not supported. Incorrectly doing overclock/overvoltage may result in damage to the hardware components such as CPU, chipset, and memory and reduce the useful life of these compo[...]

- 73 - Unique Features 4-4 Easy Energy Saver GIGABYTE Easy Energy Saver is a revolutionary technology that delivers unparalleled power savings with a click of the button. Featuring an advanced proprietary software design, GIGABYTE Easy Energy Saver is able to provide exceptional power savings and enhanced power efciency without sacricing comp[...]

Unique Features - 74 - C. Stealth Mode In Stealth Mode, the system continues t o work with the user-dened power saving settings, even after the system is restarted. Re-enter the application only if you want to make any changes or completely close the application. (Note 1) Maximize system power saving with Dynamic CPU Frequency Function; system p[...]

- 75 - Unique Features 4-5 Q-Share Q-Share is an easy and convenient data sharing too l. After conguring your LAN connection settings and Q-Share, you are able to share your data with computers on the same network, making full use of Internet resources. Directions for using Q-Share After installing Q-Share from the motherboard driver disk, go to[...]

Unique Features - 76 - 4-6 Time Repair Based on the Microsoft Volume Shadow Copy Services technology, Time Repair allows you to quickly back up and restore your system data in the Windows Vista operating system. Time Repair supports NTFS le system and can restore system data on P A T A and SA T A hard drives. System Restore Choose a system resto[...]

- 77 - Appendix Chapter 5 Appendix 5-1 Conguring SA T A Hard Drive(s) T o congure SA T A hard drive(s), follow the steps below: A. Install SA T A hard drive(s) in your computer . B. Congure SA T A controller mode in BIOS Setup. C. Congure a RAID array in RAID BIOS. (Note 1) D. Make a oppy disk containing the SA T A RAID/AHCI driver f[...]

Appendix - 78 - B. Conguring SA T A controller mode in BIOS Setup Make sure to congure the SA T A controller mode correctly in system BIOS Setup. Step 1: Turn on your com puter an d press < Delete> to enter BIOS Set up duri ng the POS T (Power-O n Self-T est). En s u r e O n C h i p S AT A C o n tr o l l e r i s e n a b l e d u n d e r [...]

- 79 - Appendix C. Conguring RAID set in RAID BIOS Enter the RAID BIOS setup utility to congure a RAID array . Skip this step and proceed with the installation of Windows operating system for a non-RAID conguration. Step 1: After the POST memory test begins and before the operating system boot begins, look for a message which says "Pr[...]

Appendix - 80 - Create Arrays Manually T o create a new array , press <2> to enter the Dene LD Menu window (Figure 4). The Dene LD selection from the Main Menu allows users to begin the process of manually dening the drive elements and RAID levels for one or multiple disk arrays. In Figure 4, use the up or down arrow key to move to a[...]

- 81 - Appendix In the following procedure, we'll create RAID 0 as an example. 1. Under the RAID Mode section, press the <SP ACE> key to select RAID 0 . 2. Set the Stripe Block size. 64 KB is the default. 3. Under the Drives Assignments section, press the up or down arrow key to highlight a drive. 4. Press the <SP ACE> key or <Y[...]

Appendix - 82 - Delete an Array The Delete Array menu option allows for deletion of disk array assignments. Deleting an existing disk array could result in loss of data. Record all array information including the array type, the disk members, and stripe block size in case you wish to undo a deletion. 1. T o delete an array , press <3> in the [...]

- 83 - Appendix 5-1-2 Making a SA T A RAID/AHCI Driver Diskette (Required for AHCI and RAID Mode) T o successfully install operating system onto SA T A hard drive(s) that is/are congured to RAID/AHCI mode, you need to install the SA T A controller driver during the OS installation. Without the driver, the hard drive may not be recognized during [...]

Appendix - 84 - 5-1-3 Installing the SA T A RAID/AHCI Driver and Operating System With the SA T A RAID/AHCI driver diskette and correct BIOS settings, you are ready to install Windows Vista/ XP onto your hard drive(s). The followings are examples of Windows XP and Vista installation. A. Installing Windows XP Step 1: Restart your system to boot from[...]

- 85 - Appendix B. Installing Windows Vista (The procedure below assumes that only one RAID array exists in your system.) Step 1: Restart your system to boot from the Windows Vista setup disk and perform standard OS installation steps. When a screen similar to that below appears (RAID hard drive will not be detected at this stage), select Load Driv[...]

Appendix - 86 - Step 3: When a screen as shown in Figure 5 appears, select AMD AHCI Compatible RAID Controller and press Next . Step 4: After the driver is loaded, the RAID drive will appear . Select the RAID drive and then press Next to continue the OS installation (Figure 6). Figure 5 Figure 6[...]

- 87 - Appendix Rebuilding an Array: Rebuilding is the process of restoring data to a hard drive from other drives in the array . Rebuilding applies only to fault-tolerant arrays such as RAID 1 or RAID 10 arrays. T o replace the old drive, make sure to use a new drive of equal or greater capacity . The procedures below assume a new drive is added t[...]

Appendix - 88 - 5-2-1 Conguring 2/4/5.1/7.1-Channel Audio The motherboard provides six audi o jacks on the b ack pan el w hi ch s upp or t 2/ 4/ 5.1 /7 .1 -ch an ne l (Note) au dio . The picture to the right shows the default audio jack assignments. The integrated HD (High Definition) audio provides jack retasking capability that allows the user[...]

- 89 - Appendix Step 2: Connect an audio device to an audio jack. The The cur- rent connected device is dialog box appears. Select the device according to the type of device you connect. Then click OK . Step 3: On the Speakers s creen, click t he Spe aker Co ngur a - tion tab. In the Speaker Conguration list, select Stereo , Quadraphonic , 5.[...]

Appendix - 90 - 5-2-2 Conguring S/PDIF In/Out The S/PDIF In and Out cable (optional) provides S/PDIF In and S/PDIF Out functionalities. (Note) The actual locations of the SPDIF In and SPDIF Out connectors may differ by model. Coaxial S/PDIF Out Optical S/PDIF Out Optical S/PDIF In Coaxial S/PDIF In Step: After connecting the S/PDIF In device, ac[...]

- 91 - Appendix C. Conguring S/PDIF Out: The S/PDIF Out jacks can transmit audio signals to an external decoder for decoding to get the best audio quality . T o output S/PDIF digital audio signals to an external decoder, connect a S/PDIF coaxial cable or a S/PDIF optical c able (either one ) to the optical /coxial S/PDIF o ut connector on t he m[...]

Appendix - 92 - 5-2-3 Enabling the Dolby Home Theater Function Before D olby Hom e Theater is enabled , you get only 2-c hannel p laybac k output (from th e front speakers) when playing 2-channel stereo sources. Y ou must play 4-, 5.1-, or 7.1- chan- nel content to get 4-, 5.1-, or 7.1- channel audio effects. With Dolby Home Theater enabled, 2-chan[...]

- 93 - Appendix 5-2-4 Conguring Microphone Recording Step 1: After installing the audio driver , the HD Audio Manager icon will appear in the notication area. Double-click the icon to access the HD Audio Manager . Step 2: Connect your microphone to the Mic in jack (pink) on th e ba c k pa ne l o r th e M ic i n j ac k ( pi nk ) o n th e f ro [...]

Appendix - 94 - Step 4: T o r ai s e t h e r e c o rd i n g a n d p l a yb a c k v o l um e f o r t h e microphone, click the Microphone Boost icon on the right of the Recor ding V olume slider and set the Microphone Boost level. Step 5: After co mpletin g the set tings a bove, cl ick Start , p oint to All Programs , point to Accessories , and then[...]

- 95 - Appendix Step 3: When the Stereo Mix item appears, right-click on this item and select Enable . Then set it as the default de- vice. Step 4: Now you can access the HD Audio Manager to cong - ure Stereo Mix and use Sound Recorder to record the sound. 5-2-5 Using the Sound Recorder A. Recording Sound 1. Make sure you have connected the soun[...]

Appendix - 96 - 5-3 T roubleshooting 5-3-1 Frequently Asked Questions T o read more FAQs for your motherboard, please go to the Support&DownloadsMotherboardF AQ page on GIGABYTE's website. Q: In the BIOS Setup program, why are some BIOS options missing? A: Some advanced options are hidden in the BIOS Setup program. Press <Delete> t[...]

- 97 - Appendix 5-3-2 T roubleshooting Procedure If you encounter any troubles during system startup, follow the troubleshooting procedure below to solve the problem. ST ART A Turn off the power . Remove all peripherals, connecting cables, and power cord etc. Isolate the short circuit. Secure the CPU cooler on the CPU. Connect the CPU cooler power [...]

Appendix - 98 - The power supply , CPU or CPU socket might fail. The keyboard or keyboard connector might fail. END A Turn off the computer . Plug in the keyboard and mouse and restart the computer . The graphics card, expansion slot, or monitor might fail. The IDE/SA TA device, connector , or cable might fail. No The problem is veried and solve[...]

- 99 - Appendix 5-4 Regulatory Statements Regulatory Notices This document must not be copied without our writt en permission, and the con tents there of must not be imparted to a third party nor be used for any unauthorized purpose. Contravention will be prosecuted. We believe that the information contained herein was accurate in all respects at t[...]

Appendix - 100 - Finally , we suggest that you practice other environmentally friendly actions by understanding and using the energy-saving features of this product (where applicable), recycling the inner and outer packaging (including shipping containers) this product was delivered in, and by disposing of or recycling used batteries properly . Wit[...]

- 101 - Appendix[...]

Appendix - 102 -[...]

- 103 - Appendix Contact Us • GIGA-BYTE TECHNOLOGY CO., L TD. Address: No.6, Bau Chiang Road, Hsin-Tien, T aipei 231, T aiwan TEL: +886-2-8912-4000 F AX: +886-2-8912-4003 T ech. and Non-T ech. Support (Sales/Marketing) : http://ggts.gigabyte.com.tw WEB address (English): http://www .gigabyte.com.tw WEB address (Chinese): http://www .gigabyte.tw ?[...]

Appendix - 104 - • GIGABYTE Global Service System T o su bmit a te chnic al or no n-tech nical (Sales /Mark et- ing) question, please link to: http://ggts.gigabyte.com.tw Then select your language to enter the system. • G.B.T . TECHNOLOGY TRADING GMBH - Germany WEB address : http://www .gigabyte.de • G.B.T . TECH. CO., L TD. - U.K. WEB add[...]