English dropdown-ico

Heat & Glo Everest manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Heat & Glo Everest, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Heat & Glo Everest one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Heat & Glo Everest. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Heat & Glo Everest should contain:
- informations concerning technical data of Heat & Glo Everest
- name of the manufacturer and a year of construction of the Heat & Glo Everest item
- rules of operation, control and maintenance of the Heat & Glo Everest item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Heat & Glo Everest alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Heat & Glo Everest, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Heat & Glo service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Heat & Glo Everest.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Heat & Glo Everest item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    Heat & Glo • Everest • 750-900 Rev . o • 10/08 1 Model: Everest • DO NOT store or use gasoline or other fl am- mable vapors and liquids in the vicinity of this or any other appliance. • What to do if you smell gas - DO NOT try to light any appliance. - DO NOT touch any electrical switch. DO NOT use any phone in your building. - Immed[...]

  • Page 2

    Heat & Glo • Everest • 750-900 Rev . o • 10/08 2 ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! Safety and W arning Information ! ! DO NOT place furniture or any other combustible household objects within 36 inches of the fi replace front. Any safety screen or guard removed for servicing must be replaced before operating this appliance. Turn off the [...]

  • Page 3

    Heat & Glo • Everest • 750-900 Rev . o • 10/08 3 T able of Contents Safety and W arning Information . .................................... 2 Service Parts Lists . .......................................................... 4 Section 1: Approvals and Codes . ................................... 7 Appliance Certi fi cation ..................[...]

  • Page 4

    Heat & Glo • Everest • 750-900 Rev . o • 10/08 4 Service Parts Diagram Service Parts EVEREST Beginning Manufacturing Date: Aug. 2000 Ending Manufacturing Date: ______ 7 8 9 10 11 12 13 14 15 Part number list on following page. Log Set Assembly 2 6 5 4 3[...]

  • Page 5

    Heat & Glo • Everest • 750-900 Rev . o • 10/08 5 Service Parts List EVEREST IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may be ordered from an authorized dealer . Stocked at Depot ITEM DESCRIPTION C[...]

  • Page 6

    Heat & Glo • Everest • 750-900 Rev . o • 10/08 6 2 3 3 5 4 6 10 9 8 11 17 18 19 V alve Assembly Parts List 1 2 3 3 4 5 6 7 8 9 10 11 12 13 14 15 16 IPI V alve Assembly Post Serial #5000 Standing Pilot V alve Assembly Pre Serial #5000 Service Parts EVEREST Beginning Manufacturing Date: Aug. 2000 Ending Manufacturing Date: ______ IMPORT ANT[...]

  • Page 7

    Heat & Glo • Everest • 750-900 Rev . o • 10/08 7 Installation Codes The fi replace installation must conform to local codes. Before installing the fi replace, consult the local building code agency to ensure that you are in compliance with all applicable codes, including permits and inspections. In the absence of local codes, the fi re[...]

  • Page 8

    Heat & Glo • Everest • 750-900 Rev . o • 10/08 8 2 Getting Started Introducing the Heat & Glo Gas Fireplaces Heat & Glo direct vent gas fi replaces are designed to op- erate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside. The information contained in this Installers Gui[...]

  • Page 9

    Heat & Glo • Everest • 750-900 Rev . o • 10/08 9 Figure 1. Diagram of the Everest TOP ST ANDOFFS TOP VENT COLLARS TRIM DOOR RA TING PLA TE AND LABELS GAS CONTROLS ELECTRICAL ACCESS GAS LINE ACCESS Ø8 (203.1) 8 (203 mm) 8-15/16 (227 mm) 20-7/8 (531 mm) ELECTRICAL ACCESS 4-1 1/16 (1 19 mm) 2-5/16 (59 mm) 49-7/8 (1266 mm) 4-1 1/16 (1 18 mm)[...]

  • Page 10

    Heat & Glo • Everest • 750-900 Rev . o • 10/08 10 3 Installing the Fireplace Step 1. Locating the Fireplace The diagram below shows space and clearance require- ments for locating a fi replace within a room. A B C D E 35 1/2” 21 3/4” 30 1/2” 43 1/4” 61 3/16” (902 mm) (552 mm) (775 mm) (1099 mm) (1554 mm) Minimum Clearances from[...]

  • Page 11

    Heat & Glo • Everest • 750-900 Rev . o • 10/08 11 Figure 5. V ent Components and T erminations Step 3. Installing the V ent System A. V ent System Approvals These models are approved to use D VP-series direct vent pipe components and terminations. Approved vent system components are labeled for identi fi ca- tion. This pipe is tested and[...]

  • Page 12

    Heat & Glo • Everest • 750-900 Rev . o • 10/08 12 STRAIGHT UP VERTICAL VENTING V (FT .) 40’ MAX. (12.4 M) Figure 6. Straight Up V ertical V enting V CAP[...]

  • Page 13

    Heat & Glo • Everest • 750-900 Rev . o • 10/08 13 Figure 7. V enting with One 90° Elbow NOTE: If a 90º elbow is fi rst attached to the unit, the maximum horizontal run is 3 feet (914 mm). NOTE: For corner installations: A 6 inch (152 mm) section of straight pipe may need to be attached to the fi replace before a 90º elbow , to allow [...]

  • Page 14

    Heat & Glo • Everest • 750-900 Rev . o • 10/08 14 V H + H 1 1’ MIN. (305 mm) 10’ MAX. (3.1 m) 2’ MIN. (610 mm) 15’ MAX. (4.65 m) 4’ MIN. (1.22 m) 20’ MAX. (6.2 m) V+H+H 1 = 40’ MAX. (12.4 m) H+H 1 = 20´ MAX. (6.2 m) V+V 1 +H = 40’ MAX. (12.4 m) Figure 8. V enting with T wo 90° Elbows VENTING WITH TWO (2) 90° ELBOWS H 1 [...]

  • Page 15

    Heat & Glo • Everest • 750-900 Rev . o • 10/08 15 V H H 1 V 1 V H H 1 V 1 Figure 9. V enting with three 90° elbows VENTING WITH THREE (3) 90° ELBOWS V + V 1 H + H 1 1’ MIN. (305 mm) 10’ MAX. (3.1 m) 2’ MIN. (610 mm) 15’ MAX. (4.65 m) 4’ MIN. (1.22 m) 20’ MAX. (6.2 m) NOTE: H + H 1 = 20’ MAX. (6.2 m) V + V 1 + H + H 1 = 40?[...]

  • Page 16

    Heat & Glo • Everest • 750-900 Rev . o • 10/08 16 Figure 10. V ertical Baf fl e 1. Attach the First V ent Component to the Starting Collars T o attach the fi rst vent component to the starting collars of the fi replace: • Make sure that the fi replace gasket supplied with the fi replace seals between the fi rst component and the o[...]

  • Page 17

    Heat & Glo • Everest • 750-900 Rev . o • 10/08 17 Figure 1 1 ! DI RECTI ON UP HEAT S HI ELD COMBUSTI BLE S URF ACE 90 EL BO W 0 Figure 12 CORRECT INCORRECT COMBUSTIBLE SURF ACE HEA T SHIELD 3“ MIN. (76 MM) 3. Install Support Brackets Refer to Cinch Pipe and T ermination Cap installation in- structions. T o Install the Heat Shield: 1. De[...]

  • Page 18

    Heat & Glo • Everest • 750-900 Rev . o • 10/08 18 For Vertical Runs - One ceiling fi restop is REQUIRED at the hole in each ceiling through which the vent passes. T o install fi restops for vertical runs that pass through ceilings: • Position a plumb bob directly over the center of the verti- cal vent component. • Mark the ceiling t[...]

  • Page 19

    Heat & Glo • Everest • 750-900 Rev . o • 10/08 19 Figure 17. T rapezoid T ermination Cap 7-1/4 in. (184 mm) ! WARNING: VENTING TERMINALS SHALL NOT BE RECESSED INTO A WALL OR SIDING. VENT TERMINATION CLEARANCES MUST BE FOLLOWED TO AVOID FIRE DANGER. SEE VENT TERMINATION MINIMUM CLEARANCES DIAGRAM ON FOLLOWING PAGE. C. V ent T ermination Re[...]

  • Page 20

    Heat & Glo • Everest • 750-900 Rev . o • 10/08 20 V = VENT TERMINAL X = AIR SUPPL Y INLET = AREA WHERE TERMINAL IS NOT PERMITTED Figure 18. Minimum Clearances for T ermination A = 12 inches................. clearances above grade, ver anda, porch, deck or balcony B = 12 inches................. clearances to window or door that may be open[...]

  • Page 21

    Heat & Glo • Everest • 750-900 Rev . o • 10/08 21 For V ertical T erminations - T o locate the vent and install the vent sections: • Locate and mark the vent centerpoint on the underside of the roof, and drive a nail through the centerpoint. • Make the outline of the roof hole around the centerpoint nail. • The size of the roof hole[...]

  • Page 22

    Heat & Glo • Everest • 750-900 Rev . o • 10/08 22 ! Step 4. Positioning, Leveling, and Securing the Fireplace The diagram below shows how to properly position, level, and secure the fi replace. ! ! Figure 20. Proper Positioning, Leveling, and Securing of a Fireplace Figure 21. Intermittent Pilot Ignition NAILING T ABS (BOTH SIDES) Step 5[...]

  • Page 23

    Heat & Glo • Everest • 750-900 Rev . o • 10/08 23 Figure 22. Gas Supply Line • At the gas line access hole, use insulation to re-pack the space around the gas pipe. • Insert insulation from the outside of the fi replace and pack the insulation tightly to totally seal between the pipe and the outer casing. Step 6. The Gas Supply Line [...]

  • Page 24

    Heat & Glo • Everest • 750-900 Rev . o • 10/08 24 Step 8. Wiring the Fireplace NOTE: Electrical wiring must be installed by a licensed electrician. CAUTION: DISCONNECT REMOTE CONTROLS IF YOU ARE ABSENT FOR EXTENDED TIME PERIODS. THIS WILL PREVENT ACCIDENT AL FIREPLACE OPERA TION. Intermittent Pilot Ignition (IPI) Wiring Appliance Requirem[...]

  • Page 25

    Heat & Glo • Everest • 750-900 Rev . o • 10/08 25 Step 9. Finishing The following diagram shows the minimum vertical and corresponding maximum horizontal dimensions of fi replace mantels or other combustible projections above the top front edge of the fi replace. See Figures 2 and 3 for other fi replace clearances. Only non-combustible[...]

  • Page 26

    Heat & Glo • Everest • 750-900 Rev . o • 10/08 26 Step 10. Installing T rim, Logs and Ember Material Installing the T rim Combustible materials may be brought up to the speci fi ed clearances on the side and top front edges of the fi replace, but MUST NEVER overlap onto the front face. The joints between the fi nished wall and the fi [...]

  • Page 27

    Heat & Glo • Everest • 750-900 Rev . o • 10/08 27 Step 1 1. Before Lighting the Fireplace Before lighting the fi replace, be sure to do the following: Remove all paperwork from underneath the fi replace. Review safety warnings and cautions • Read the Safety and Warning Information section at the beginning of this Installers Guide . Do[...]

  • Page 28

    Heat & Glo • Everest • 750-900 Rev . o • 10/08 28 4 Maintaining and Servicing Y our Fireplace Fireplace Maintenance Although the frequency of your fi replace servicing and maintenance will depend on use and the type of installation, you should have a quali fi ed service technician perform an appliance check-up at the beginning of each h[...]

  • Page 29

    Heat & Glo • Everest • 750-900 Rev . o • 10/08 29 Heat & Glo, a brand of Hearth & Home T echnologies Inc. 20802 Kensington Boulevard, Lakeville, MN 55044 www .heatnglo.com Contact Information Please contact your Heat & Glo dealer with any questions or concerns. For the location of your nearest Heat & Glo dealer , please vi[...]