Go to page of
Similar user manuals
-
Indoor Fireplace
Heatiator NB3630M
68 pages 3.66 mb -
Indoor Fireplace
Heatiator C40
71 pages 7.53 mb -
Indoor Fireplace
Heatiator CD4236IR-C
73 pages 4.45 mb -
Indoor Fireplace
Heatiator BH42A
23 pages 7.62 mb -
Indoor Fireplace
Heatiator ECO-WINS18
48 pages 4.87 mb -
Indoor Fireplace
Heatiator ADI60S
41 pages 1.84 mb -
Indoor Fireplace
Heatiator I80
56 pages 4.5 mb -
Indoor Fireplace
Heatiator CB4236IR
40 pages 4.25 mb
A good user manual
The rules should oblige the seller to give the purchaser an operating instrucion of Heatiator HEIR36H, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.
What is an instruction?
The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Heatiator HEIR36H one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.
Unfortunately, only a few customers devote their time to read an instruction of Heatiator HEIR36H. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.
What should a perfect user manual contain?
First and foremost, an user manual of Heatiator HEIR36H should contain:
- informations concerning technical data of Heatiator HEIR36H
- name of the manufacturer and a year of construction of the Heatiator HEIR36H item
- rules of operation, control and maintenance of the Heatiator HEIR36H item
- safety signs and mark certificates which confirm compatibility with appropriate standards
Why don't we read the manuals?
Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Heatiator HEIR36H alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Heatiator HEIR36H, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Heatiator service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Heatiator HEIR36H.
Why one should read the manuals?
It is mostly in the manuals where we will find the details concerning construction and possibility of the Heatiator HEIR36H item, and its use of respective accessory, as well as information concerning all the functions and facilities.
After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.
Table of contents for the manual
-
Page 1
1 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 • DO NOT store or use gasoline or other fl am- mable vapors and liquids in the vicinity of this or any other appliance. • What to do if you smell gas - DO NOT try to light any appliance. - DO NOT touch any electrical switch. DO NOT use any phone in your building. - Immediate[...]
-
Page 2
2 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 Listing Label Information/Location Model Name: ___________________________________________ Date purchased/installed: __________________ Serial Number: __________________________________________ Location on fi replace: _____________________ Dealership purchased from: ____________[...]
-
Page 3
3 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 Safety Alert Key: • DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury . • W ARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury . • CAUTION! Indicates a hazardous situation [...]
-
Page 4
4 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 = Contains updated information. 14 Appliance Setup A. Remove Fixed Glass Assembly . . . . . . . . . . . . . . . . . . . . 53 B. Remove the Shipping Materials . . . . . . . . . . . . . . . . . . . . 53 C. Clean the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . [...]
-
Page 5
5 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 B. Limited Lifetime W arranty 4021-645C 12-29-10 Page 1 of 2 Hearth & Home T echnologies Inc. LIMITED LIFETIME W ARRANTY Hearth & Home T echnologies Inc., on behalf of its hearth brands (”HHT”), extends the following warranty for HHT gas, wood, pellet, coal and electr[...]
-
Page 6
6 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 4021-645C 12-29-10 Page 2 of 2 W ARRANTY CONDITIONS: 7KLVZDUUDQWRQOFRYHUV++7DSSOLDQFHVWKDWDUHSXUFKDVHGW KURXJKDQ++7 DXWKRUL]HGGHDOHURUGLVWULEXWRU $ OLVWRI ++7DXWKRUL]HGGHDOHUVLVDYDLODEOHRQWKH?[...]
-
Page 7
7 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 C. BTU Speci fi cations This product is listed to ANSI standards for “V ented Gas Appliance Heaters” and applicable sections of “Gas Burn- ing Heating Appliances for Manufactured Homes and Recreational V ehicles”, and “Gas Fired Appliances for Use at High Altitudes”.[...]
-
Page 8
8 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 H. Requirements for the Commonwealth of Massachusetts For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes, including those owned or operated by the Commonwealth and where t[...]
-
Page 9
9 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 Figure 2.1 General Operating Parts B. Y our Fireplace W ARNING! DO NOT operate fi replace before read- ing and understanding operating instructions. Failure to operate fi replace according to operating instructions could cause fi re or injury . DECORA TIVE DOORS (NOT SHOWN) SE[...]
-
Page 10
10 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 C. Clear Space W ARNING! DO NOT place combustible objects in front of the fi replace or block louvers. High temperatures may start a fi re. See Figure 2.2. Avoid placing candles and other heat-sensitive objects on mantel or hearth. Heat may damage these objects. Figure 2.2 Cle[...]
-
Page 11
11 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 J. Before Lighting Fireplace Before operating this fi replace for the fi rst time, have a quali fi ed service technician : • V erify all shipping materials have been removed from inside and/or underneath the fi rebox. • Review proper placement of logs, ember material and[...]
-
Page 12
12 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 K. Lighting Instructions (IPI) 1. This appliance is equipped with an ignition device which automatically lights the burner. DO NOT try to light the burner by hand. 2. Wait fi ve (5) minutes to clear out any gas. Then smell for gas, including near the fl oor. If you smell gas, [...]
-
Page 13
13 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 L. After Fireplace is Lit Initial Break-in Procedure • The fireplace should be run three to four hours continuously on high. • T urn the fi replace off and allow it to completely cool. • Remove fi xed glass assembly . See Section 14.H. • Clean fi xed glass assembly . [...]
-
Page 14
14 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 3 3 Maintenance and Ser vice A. Maintenance T asks-Homeowner The following tasks may be performed annually by the homeowner . If you are uncomfortable performing any of the listed tasks, please call your dealer for a service ap- pointment. More frequent cleaning may be required [...]
-
Page 15
15 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 B. Maintenance T asks-Quali fi ed Service T echnician The following tasks must be performed by a quali fi ed ser- vice technician. Glass Cleaning (Exterior and Interior of Installed Glass) Frequency: Seasonally By: Quali fi ed Service T echnician T ools Needed : Protective gl[...]
-
Page 16
16 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 Figure 3.1 IPI Pilot Flame Patterns Burner Ignition and Operation Frequency: Annually By: Quali fi ed Service T echnician T ools needed: Protective gloves, vacuum cleaner , whisk broom, fl ashlight, voltmeter , indexed drill bit set, and a manometer . • V erify burner is pro[...]
-
Page 17
17 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 A. T ypical Appliance System NOTICE: Illustrations and photos re fl ect typical installations and are for design purposes only . Illustrations/diagrams are not drawn to scale. Actual product may vary from pictures in manual. Figure 4.1 T ypical System HORIZONT AL TERMINA TION C[...]
-
Page 18
18 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 B. Design and Installation Considerations Heatilator direct vent gas appliances are designed to op- erate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside. No additional outside air source is required. Installation MUST [...]
-
Page 19
19 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 5 5 F raming and Clearances A. Selecting Appliance Location When selecting a location for the appliance it is important to consider the required clearances to walls (see Figure 5.1). W ARNING! Risk of Fire or Burns! Provide adequate clearance around air openings and for service [...]
-
Page 20
20 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 C B D A B. Constructing the Appliance Chase A chase is a vertical box-like structure built to enclose the gas appliance and/or its vent system. In cooler climates the vent should be enclosed inside the chase. NOTICE: T reatment of ceiling fi restops and wall shield fi restops [...]
-
Page 21
21 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 D. Mantel and W all Projections W ARNING! Risk of Fire! Comply with all minimum clear- ances as speci fi ed. Framing or fi nishing material closer than the minimums listed must be constructed entirely of non- combustible materials (i.e., steel studs, concrete board, etc). Comb[...]
-
Page 22
22 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 6 12 10 18 21 FIREPLACE OPENING 1-1/4 IN. SEE SECTION 13.D 1/2 IN. NON-COMBUSTIBLE MA TERIAL HEIR36 HEIR42 MAX. MIN. Note: All measurements in inches. Note: Measurement is taken from top of the opening, NOT the top of the fi replace. Non-Combustible Mantel Projections 1 9 3 6 1[...]
-
Page 23
23 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 Figure 5.10 Non-Combustible Hearth Extension Dimensions MODEL A B in. mm in. mm HEIR36 12 305 57-1/4 1454 HEIR42 12 305 63-5/16 1608 HEIR50 12 305 71-5/16 181 1 A B NON-COMBUSTIBLE NON-COMBUSTIBLE BOARD HEARTH CLEARANCE BRACKET WOOD OR OTHER COMBUSTIBLE FLOOR OR PLA TFORM 4 IN. [...]
-
Page 24
24 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 A. V ent T ermination Minimum Clearances Roof Pitch H (Min.) Ft. Flat to 6/12...........................................................1.0* Over 6/12 to 7/12 .................................................1.25* Over 7/12 to 8/12 ...............................................[...]
-
Page 25
25 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 O N P R Q C J B D B F B A E V V V V V V M H or i V G X V H A V V H Electrical Service V K V K V L C V Figure 6.3 Minimum Clearances for T ermination X = AIR SUPPL Y INLET A = 12 inches................. clearances above grade, veranda, porch, deck or balcony B = 12 inches........[...]
-
Page 26
26 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 A. Approved Pipe This appliance is approved for use with Hearth & Home T echnologies DVP venting systems. Refer to Section 16.B for vent component information. DO NOT mix pipe, fi ttings or joining methods from differ- ent manufacturers. The pipe is tested to be run inside [...]
-
Page 27
27 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 H 1 V 1 1. T op V ent - Horizontal T ermination Figure 7.3 One Elbow Fire Risk. Explosion Risk. Do NOT pack insulation or other combustibles between ceiling fi restops. • AL W A YS maintain speci fi ed clearances around venting and fi restop systems. • Install wall shield[...]
-
Page 28
28 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 H 2 H 1 INST ALLED HORIZONT ALL Y V 1 Figure 7.4 T wo Elbows Note: Flue restrictor is permit- ted ONL Y on 30 ft. minimum vertical runs with no elbows. W ARNING! Risk of Fire! • HEIR36(NG/LP), HEIR42(NG/LP) and HEIR50(NG/LP) models require a minimum of 36 inches of vertical ve[...]
-
Page 29
29 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 1. T op V ent - Horizontal T ermination - (continued) Figure 7.5 Three Elbows HEIR36 (NG/LP), HEIR42 (NG/LP), HEIR50 (NG/LP) V 1 H 1 V 2 H 2 2 ft 610 mm 7 in 178 mm * H 2 Max = 2 X V 2 3 ft 914 mm 2 ft 610 mm * H 2 Max = 2 X V 2 4 ft 1.2 m 4 ft 1.2 m * H 2 Max = 2 X V 2 5 ft 1.5[...]
-
Page 30
30 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 2. T op V ent - V ertical T ermination No Elbow Figure 7.6 V 1 = 50 ft. Max. (15.2 m) V 1 = 2 ft. Min. (610 mm) NOTE: Flue Restrictor ships in manual bag assembly . Note: Flue restrictor is permit- ted ONL Y on 30 ft. minimum vertical runs with no elbows. V 1 FLUE RESTRICTOR Fig[...]
-
Page 31
31 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 Figure 7.8 HEIR36 (NG/LP), HEIR42 (NG/LP), HEIR50 (NG/LP) V 1 H 1 V 2 2 ft 610 mm 1 ft 305 mm * 3 ft 914 mm 3 ft 914 mm * 4 ft 1.2 m 4 ft 1.2 m * 5 ft 1.5 m 9 ft 2.7 m * 6 ft 1.8 m 12 ft 3.7 m * V 1 + V 2 + H 1 = 50 ft (15.2 m) Max. *No speci fi c restrictions on this value EXC[...]
-
Page 32
32 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 Three Elbows HEIR36 (NG/LP), HEIR42 (NG/LP), HEIR50 (NG/LP) V 1 H 1 H 2 V 2 H t Max. 2 ft 610 mm * * ** 7 in 178 mm 3 ft 914 mm * * ** 2 ft 610 mm 4 ft 1.2 m * * ** 4 ft 1.2 m 5 ft 1.5 m * * ** 8 ft 2.4 m 6 ft 1.8 m * * ** 12 ft 3.7 m 7 ft 2.1 m * * ** 14 ft 4.3 m 10 ft 3.0 m * [...]
-
Page 33
33 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 F . PVK-80 and PVI-SLP Information This section provides speci fi c detail for installation of HEIR36, HEIR42, and HEIR50 models with approved power vent kits. Follow instructions included with the PVK-80 or PVI-SLP power vent kits. See T able 7.1 below for approved Power V ent[...]
-
Page 34
34 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 A* B 10 in. 12 in. DO NOT P ACK WITH INSULATION OR OTHER MATERIAL A. Pipe Clearances to Combustibles W ARNING! Risk of Fire! Maintain air space clearance to vent. DO NOT pack insulation or other combustibles: • Between ceiling fi restops • Between wall shield fi restops ?[...]
-
Page 35
35 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 C. Install the Ceiling Firestop A ceiling fi restop MUST be used between fl oors and attics. • DVP pipe only - Frame an opening 10 in. by 10 in. (254 mm by 254 mm) whenever the vent penetrates a ceiling/ fl oor (see Figure 8.3). • Frame the area with the same sized lumber[...]
-
Page 36
36 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 D. Install Attic Insulation Shield W ARNING! Fire Risk. DO NOT allow loose materials or insulation to touch vent. Hearth & Home T echnologies Inc. requires the use of an attic shield. The National Fuel Gas Code ANSI Z223.1 and NFPA 54 requires an attic shield constructed of [...]
-
Page 37
37 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 9 9 Appliance Preparation A. V ent Preparation Figure 9.2 Seal Cap and Gasket Location SEAL CAP SEAL CAP GASKET GASKET CAUTION! Risk of Cuts, Abrasions or Flying Debris. Wear protective gloves and safety glasses during instal- lation. Sheet metal edges are sharp. NOTICE: This ap[...]
-
Page 38
38 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 Figure 9.3 Side Nailing T ab in Shipping Position Figure 9.4 Nailing T ab Bent Out for Installation HEA T SHIELD NAILING T AB IN SHIPPING POSITION Figure 9.5. Heat Shields and Nailing T abs in Installation Position B. Securing and Leveling the Appliance W ARNING! Risk of Fire! P[...]
-
Page 39
39 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 Figure 9.6 Shipping Location of Non-Combustible Board C. Installing Non-combustible Facing Material W ARNING! Risk of Fire! • Follow these instructions exactly . • Facing materials must be installed properly to prevent fi re. • No materials may be substituted without auth[...]
-
Page 40
40 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 1 0 10 Inst alling V ent Pipe (D VP Pipe ) A. Assemble V ent Sections Attach V ent to the Firebox Assembly Note: The end of the pipe sec tions wi t h the lanced tabs w ill face toward the appliance. Attach the fi rst pipe section to the starting collar: • Lanced pipe end of t[...]
-
Page 41
41 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 120º Figure 10.5 Securing V ertical Pipe Sections 120º Figure 10.6 Securing Horizontal Pipe Sections C. Disassemble V ent Sections • Rotate either section (see Figure 10.7) so the seams on both pipe sections are aligned as shown in Figure 10.8. • Pull carefully to separate[...]
-
Page 42
42 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 D. Install Metal Roof Flashing • See minimum vent heights for various pitched roofs (Figure 10.9) to determine the length of pipe to extend through the roof. • Slide the roof fl ashing over the pipe sections extending through the roof as shown in Figure 10.10. Roof Pitch H [...]
-
Page 43
43 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 SCREWS CAULK STORM COLLAR (1 of 3) Figure 10.13 Figure 10.13 TERMINA TION CAP F . Install V ertical T ermination Cap • Attach the vertical termination cap by sliding the inner collar of the cap into the inner fl ue of the pipe section while placing the outer collar of the cap[...]
-
Page 44
44 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 A. Fuel Conversion • Make sure the appliance is compatible with available gas types. • Conversions must be made by a qualified service technician using Hearth & Home T echnologies speci fi ed and approved parts. B. Gas Pressure • Optimum appliance performance requires[...]
-
Page 45
45 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 1 2 12 Electr ical Information Figure 12.1 IPI Wiring Diagram TO JUNCTION BOX (1 10V) MODULE I S FLAME SENSE IGNITER GROUND ORANGE (PILOT) GREEN (MAIN) BROWN BLACK RED BA TTERY P ACK 6V DC FLAME MODULA TION ORANG E WHITE TO CUSTOM ER-SUPPLIED W ALL SWITCH JUMPE R WIRE BLAC K RED[...]
-
Page 46
46 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 Figure 12.3 Junction Box Detail NOTICE: DO NOT wire 1 10 V AC to wall switch. GRN wire inside box Copper ground attached to GRN screw with GRN wire WHT WHT BLK BLK 14/2WG Romex Connector D. Electrical Service and Repair W ARNING! Risk of Shock! Label all wires prior to dis- conn[...]
-
Page 47
47 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 1 3 13 Fi nishing A. Finishing T emplates T wo side fi nishing templates and one top fi nishing template are supplied with the appliance. They are fastened to the top surround. INSIDE FIT Method: The fi nishing template pieces are required for installations that require more [...]
-
Page 48
48 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 Figure 13.6. Splatter Guard Installation B. Splatter Guard The splatter guard is a piece of corrugated material used to protect the appliance during the installation process before fi nishing work on the whole hearth is complete. Splatter guards may be factory installed or acco[...]
-
Page 49
49 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 C. Mantel and W all Projections W ARNING! Risk of Fire! Comply with all minimum clear- ances as speci fi ed. Framing closer than the minimums listed must be constructed entirely of non-combustible materials (i.e., steel studs, concrete board, etc.). FIREPLACE OPENING COMBUSTIBL[...]
-
Page 50
50 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 Non-Combustible Mantel Projections Combustible Mantel Projections 1 9 3 6 12 9 12 15 18 21 FIREPLACE OPENING 1/2 IN. NON-COMBUSTIBLE MA TERIAL HEIR36 HEIR42 MAX. MIN. Note: All measurements in inches. Note: Measurement is taken from top of the opening, NOT the top of the fi rep[...]
-
Page 51
51 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 D. Facing Material • Metal front faces may be covered with non-combustible materials only . • Facing and/or fi nishing materials must not interfere with air fl ow through louvers, operation of louvers or doors, or access for service. • Facing and/or fi nishing materials[...]
-
Page 52
52 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 FINISHING MA TERIAL FINISHING MA TERIAL IF FINISHING MA TERIAL IS THICKER THAN 1-1/2 IN. DOORS WILL ONL Y OPEN AS F AR AS PICTURED 1-1/2 IN. MEASURE FROM FIREPLACE OPENING Figure 13.16 Minimum Side Clearance for Operable Doors A B COMBUSTIBLE MA TERIAL C (ARCH) DIMENSION INOPERA[...]
-
Page 53
53 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 A. Remove Fixed Glass Assembly See Section 14.H. B. Remove the Shipping Materials Remove shipping materials from inside or underneath the fi rebox. C. Clean the Appliance Clean/vacuum any sawdust that may have accumulated inside the fi rebox or underneath in the control cavity[...]
-
Page 54
54 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 G. Install the Log Assembly Log Set Assembly: LOGS-HEIR36 LOGS-HEIR42 Models: HEIR36H, HEIR36S HEIR42H, HEIR42S Figure 4 CAUTION: Logs are fragile, handle with care. Log #1 (2284-701) : Locate log placement slot on the bottom of log #1. See Figure 2. Mate slot on the bottom of L[...]
-
Page 55
55 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 Figure 8 Log #4 (2284-704) : See Figure 8. Place Log #4 in appliance with burned edge facing center . The bottom of Log #4 will rest on bottom refractory . Slide bottom of Log #4 forward until it contacts back side of Log #2. Log should also be positioned as close to the burner [...]
-
Page 56
56 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 2284-935C Log #5 (2284-705) : Locate fl at areas on Log #1 and Log #3 that will be used to position Log #5. See Figure 1 1. Place Log #5 into appliance as shown in Figure 12. Log #5 should contact base refractory and rest on the fl at areas as shown in Figure 1 1. Burned porti[...]
-
Page 57
57 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 Log Set Assembly: LOGS-HEIR50 Models: HEIR50T , HEIR50H LOG PLACEMENT INSTRUCTIONS CAUTION: Logs are fragile, handle with care. Log #1 (2285-701) : Locate log placement notch on the bottom of log #1. See Figure 2. Mate notch on the bottom of Log #1 with outside grate tines. Slid[...]
-
Page 58
58 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 Log #5 (2285-705) : Locate notched area on Log #1 that will be used to position Log #5. See Figure 2. Place Log #5 into appliance with “burned” edge toward center of appliance. See Figure 1 1. Log will sit on bottom refractory and should be about 1-1/2 inches from right grat[...]
-
Page 59
59 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 2285-935 Figure 12. Log Set Installed 1 1 2 2 4 4 3 3 6 6 5 5 Log #6 (2285-706) : Place Log #6 into appliance as shown in Figure 12. Bottom corner of Log #6 should be about 1/2 inch from right hand grate tine. Log will contact right center grate tine. The top of Log #6 should re[...]
-
Page 60
60 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 Figure 14.4. Glass Clip T ool Location Figure 14.5 Inserting Glass Clip T ool Figure 14.3. Glass Clip T ool H. Fixed Glass Assembly W ARNING! Risk of Asphyxiation! Handle fi xed glass assembly with care. Inspect the gasket to ensure it is undamaged and inspect the glass for cra[...]
-
Page 61
61 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 TOP RET AINING RAIL NOTCH TOP RET AINING RAIL NOTCH GLASS FRAME NOTCH GLASS FRAME NOTCH Figure 14.6 Figure 14.8. Replacing Fixed Glass Assembly This fi xed glass assembly is held in place by two side clips, one top retaining rail and lower glass clips. The HEIR36 has three lowe[...]
-
Page 62
62 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 I. Air Shutter Setting Air shutter settings should be adjusted by a quali fi ed ser- vice technician at the time of installation. The air shutter is set at the factory for minimum vertical vent run. Adjust air shutter for longer vertical runs. See Figure 14.1 1. Flame Appearanc[...]
-
Page 63
63 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 1 5 15 T roubleshooting With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do experience a problem, this troubleshooting guide will assist a quali fi ed service technician in the diagnosis of a problem and [...]
-
Page 64
64 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 T roubleshooting (continued) Symptom Possible Cause Corrective Action 4. Pilot lights but contin- ues to spark, and main burner will not ignite. (If the pilot continues to spark after the pilot fl ame has been lit, fl ame recti fi cation has not occurred.) A. A shorted or loo[...]
-
Page 65
65 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 1 6 16 Reference Materials Appliance Dimensions T able HEIR36 A. Appliance Dimension Diagram Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 5. Figure 16.1 Appliance Dimensions (HEIR36) A B D C E I L M N [...]
-
Page 66
66 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 Appliance Dimensions T able HEIR42 Figure 16.2 Appliance Dimensions (HEIR42 & HEIR50) Appliance Dimensions T able HEIR50 A B D C E I L M N O P R Q GAS ACCESS ELECTRICAL ACCESS J K HEA T -ZONE ® PORT HEA T -ZONE ® PORT H F G Location Inches Millimeters J 24 610 K 23-1/2 597[...]
-
Page 67
67 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 B. V ent Components Diagrams Figure 16.3 DVP vent components 10-1/2 in. (267 mm) 10-7/8 in. (276 mm) 45 ° 7-3/8 in. (187 mm) 11-3/8 in. (289 mm) 1-1/4 in. (32 mm) 9-1/4 in. (235 mm) 13-1/4 in. (337 mm) 1/2 in. TYP DVP90ST (90° Elbow) 10 in. (254 mm) 10 in. (254 mm) 1 in. (25 m[...]
-
Page 68
68 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 DVP-TRAP1 DVP-TRAP2 DVP-TRAPK2 DVP-TRAPK1 DVP-TRAP Horizontal T ermination Cap 15-1/8 in. (384 mm) 12 in. (305 mm) 8 in. (203 mm) Max Effective Length Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). The heat shield is designed to be used on a wall 4 in. to 7-1[...]
-
Page 69
69 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 13-1/4 in. (337 mm) 24-5/8 in. (625 mm) 27-1/2 in. (699 mm) RF6M Roof Flashing Multi-pak 31 in. (787 mm) 24-5/8 in. (625 mm) 13-1/4 in. (337 mm) RF12M Roof Flashing Multi-pak BEK Trap Ca p Brick Extension 13-3/4 in. (349 mm) 5 in. (127 mm) 13-3/4 in. (349 mm) Cap Shield DRC-RADI[...]
-
Page 70
70 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 7-1/4 in. 12 in. 305 mm (184 mm) 5-1/4 in. (133 mm) 12-1/2 in. (318 mm) DVP-TVHW VerticalTermination Cap (Highwind) PVK-80 (Approved for HEIR36, HEIR42, HEIR50) 11-1/2 in. (292 mm) 12-1/2 in. (318 mm) 16 in. (406 mm) 9 in. (229 mm) 2-3/4 in. (70 mm) 12-1/4 in. (311 mm) B. V ent [...]
-
Page 71
71 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 Service Parts IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may be ordered from an authorized dealer . Stocked at Depot ITEM DESCRIPTION CO[...]
-
Page 72
72 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 Service Parts HEIR36T , HEIR36H IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may be ordered from an authorized dealer . Stocked at Depot I[...]
-
Page 73
73 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 Service Parts IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may be ordered from an authorized dealer . Stocked at Depot ITEM DESCRIPTION CO[...]
-
Page 74
74 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 Service Parts HEIR42T , HEIR42H IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may be ordered from an authorized dealer . Stocked at Depot I[...]
-
Page 75
75 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 Service Parts IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may be ordered from an authorized dealer . Stocked at Depot ITEM DESCRIPTION CO[...]
-
Page 76
76 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 Service Parts HEIR50T , HEIR50H IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may be ordered from an authorized dealer . Stocked at Depot I[...]
-
Page 77
77 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 Service Parts IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may be ordered from an authorized dealer . Stocked at Depot ITEM DESCRIPTION CO[...]
-
Page 78
78 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 Service Parts Beginning Manufacturing Date: May 2012 Ending Manufacturing Date: Active HEIR36, HEIR42, HEIR50 IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts liste[...]
-
Page 79
79 Heatilator • HEIR36, HEIR42, HEIR50 • 2285-900 Rev . D • 8/12 Heatilator , a brand of Hearth & Home T echnologies Inc. 7571 215 th Street West, Lakeville, MN 55044 www .heatilator .com D. Contact Information Please contact your Heatilator dealer with any questions or concerns. For the location of your nearest Heatilator dealer , please[...]