Go to page of
Similar user manuals
-
Dishwasher
Hobart FT1000
44 pages 2.37 mb -
Dishwasher
Hobart C44AW ML-104082
28 pages 1.57 mb -
Dishwasher
Hobart C54A ML-104198
28 pages 1.57 mb -
Dishwasher
Hobart FT900D
28 pages 2.77 mb -
Dishwasher
Hobart AM15VLF
8 pages 1.77 mb -
Dishwasher
Hobart ML-3400-MW-1
20 pages 0.72 mb -
Dishwasher
Hobart ML-138214
60 pages 11.58 mb -
Dishwasher
Hobart ML-110975
20 pages 0.57 mb
A good user manual
The rules should oblige the seller to give the purchaser an operating instrucion of Hobart AM14F, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.
What is an instruction?
The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Hobart AM14F one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.
Unfortunately, only a few customers devote their time to read an instruction of Hobart AM14F. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.
What should a perfect user manual contain?
First and foremost, an user manual of Hobart AM14F should contain:
- informations concerning technical data of Hobart AM14F
- name of the manufacturer and a year of construction of the Hobart AM14F item
- rules of operation, control and maintenance of the Hobart AM14F item
- safety signs and mark certificates which confirm compatibility with appropriate standards
Why don't we read the manuals?
Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Hobart AM14F alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Hobart AM14F, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Hobart service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Hobart AM14F.
Why one should read the manuals?
It is mostly in the manuals where we will find the details concerning construction and possibility of the Hobart AM14F item, and its use of respective accessory, as well as information concerning all the functions and facilities.
After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.
Table of contents for the manual
-
Page 1
MODEL AM14F , AM14T , & AM14TC DISHW ASHERS MODELS AM14F ML-110975 AM14T ML-110973 AM14TC ML-110974 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 937 332-3000 www.hobartcorp.com FORM 34555 ( Dec. 2000 )[...]
-
Page 2
– 2 – POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN THE EVENT THE SMELL OF GAS IS DETECTED. THIS INFORMATION CAN BE OBTAINED FROM THE LOCAL GAS SUPPLIER. IMPORT ANT IN THE EVENT A GAS ODOR IS DETECTED, SHUT DOWN UNIT(S) AT MAIN SHUTOFF VALVE AND CONTACT THE LOCAL GAS COMPANY OR GAS SUPPLIER FOR SERVICE. FOR YOUR SAFETY DO NOT [...]
-
Page 3
– 3 – TABLE OF CONTENTS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 UNPACKING . . . . . . . . . . . . . . . . . . .[...]
-
Page 4
– 4 – Installation, Operation, and Care of MODEL AM14F , AM14T , AM14TC DISHW ASHERS SA VE THESE INSTRUCTIONS GENERAL The AM14T, AM14TC, and AM14F dishwashers are semi-automatic rack-type machines. On model AM14T (Fig. 1) the doors open on opposite sides of the machine allowing the rack to move straight through. Model AM14TC can be located in a[...]
-
Page 5
– 5 – DO NOT attempt to operate this dishwasher in the chemical sanitizing mode without a properly installed, NSF-listed, chemical sanitizer feeder (not supplied with machine). Contact an authorized detergent representative for information about a chemical sanitizer feeder. The pump motor is rated 2 HP and has thermal overload protection. The f[...]
-
Page 6
– 6 – On models AM14T and AM14TC, dish tables should be turned down and fitted into the dishwasher (Fig. 2). Use an NSF approved sealer between table and tank lip to prevent leakage. Fasten the tables to the tank lip with truss head screws. Dish tables are not required with model AM14F. High-temperature or gas heat dishwashers will probably req[...]
-
Page 7
– 7 – WATER CONNECTION A suitable water hammer arrestor should be installed in the water line just ahead of the dishwasher. Without Electric or Gas Booster Water Heater The water supply line is connected to the line strainer (Fig. 1) with 3 / 4 " pipe. A manual shut off valve and pipe union are required. The required incoming water supply [...]
-
Page 8
– 8 – Static inlet gas pressure should not exceed 14" W.C. for either natural or propane gas. The minimum value is for purpose of input adjustment. The gas valve (Fig. 3) is provided with a pressure tap to measure the gas pressure downstream, which is also the manifold pressure. Gas supply piping must have a sediment trap (supplied by othe[...]
-
Page 9
– 9 – VENTING REQUIREMENTS — WITH GAS TANK HEAT The Hobart AM14F / AM14T / AM14TC dishwasher equipped for gas tank heat is not provided with a flue collar and is not intended to have the flue directly connected to a ventilation system. However, the products of combustion must be vented to the outside air. The most common method of venting is [...]
-
Page 10
– 10 – The Rate of air flow required for a vent hood is calculated using the following definitions (Fig. 6): Q = Rate of Air Flow in Cubic Feet Per Minute or [ CFM ] Required for the Hood. A = Area of Hood Opening = (L x W) in Feet 2 D = Clearance Height = Distance in Feet from lower lip of hood to top of dishwasher chamber. P = Perimeter of Ho[...]
-
Page 11
– 11 – ELECTRICAL CONNECTIONS WARNING : ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES. WARNING : DISCONNECT ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE DISCONNECT SWITCH TO INDICATE THAT YOU ARE WORKING ON THE CIRCUIT. Refer to the wiring diag[...]
-
Page 12
– 12 – OPTIONAL EQUIPMENT CONNECTIONS — Vent Fan and Gas Booster WARNING : ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES. WARNING : DISCONNECT ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE DISCONNECT SWITCH TO INDICATE THAT YOU ARE WORKING ON [...]
-
Page 13
– 13 – DETERGENT, RINSE AID, OR SANITIZER DISPENSERS — Tubing Installation All detergent, rinse aid, and / or sanitizer dispensers must have all connections sealed against leakage. The dishwasher uses 1.42 gallons per rack at a flow rate of 5.67 gallons per minute at 20 psig flowing pressure (equivalent to a maximum head pressure of 46 feet o[...]
-
Page 14
– 14 – OPTIONAL EQUIPMENT CONNECTIONS — Detergent, Rinse Aid, Sanitizer Dispensers WARNING : ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES. WARNING : DISCONNECT ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE DISCONNECT SWITCH TO INDICATE THAT Y[...]
-
Page 15
– 15 – Fig. 13 PO W ER O N / O F F FILL CYCLE WASH 1 2 4 6 Power Switch Cycle Switch Wash / Fill Switch PL-52759 Fig. 11 PL-41 178-1 MANUAL / AUTO SWITCH W ASH / RINSE SWITCH POWER SWITCH READOUT / DISPLA Y CYCLE SWITCH OPERA TION PREPARATION Place the pump strainer (when equipped), overflow tube, overflow cover, end cover, slanted strainer, an[...]
-
Page 16
– 16 – Models AM14T / AM14TC In Automatic mode, the M ANUAL / A UTO switch (Fig. 12) is on A UTOMATIC and the W ASH / R INSE switch is O FF . The wash and rinse cycles begin automatically. The wash cycle begins when the machine doors are closed. The rinse cycle begins when the wash cycle is completed. In Manual mode, the M ANUAL / A UTO switch [...]
-
Page 17
– 17 – PL-40468-1 AM14T Shown Rinse Nozzle Knurled Disk Rinse Arm Wash Arm PL-40809-1 AM14T Shown Rinse Nozzle Rinse arm W ash arm Knurled Disk – Unscrew and support both arms on release. CLEANING T he machine m ust b e thoroughly cleaned at the end of each working shift or at least daily. N ever use steel wool to clean warewasher surfaces. U[...]
-
Page 18
– 18 – MAINTENANCE WARNING : DISCONNECT ELECTRICAL POWER SUPPLY (BOTH DISHWASHER AND BOOSTER IF APPLICABLE) AND PLACE A TAG(S) AT THE DISCONNECT SWITCH(ES) TO INDICATE THE CIRCUIT(S) ARE BEING WORKED ON BEFORE BEGINNING ANY MAINTENANCE PROCEDURE. Wash Arms Upper and lower wash and rinse arms (Figs. 15, 16) should turn freely and continue turnin[...]
-
Page 19
– 19 – TROUBLESHOOTING Manual Reset Button on Pump Motor The motor is equipped with a gray manual reset button near the end cover of the motor. If the pump motor becomes overheated, the thermal overload protector will cause the motor to not operate. If this occurs, press the power switch O FF and allow the motor to cool. Then press the gray man[...]
-
Page 20
– 20 – FORM 34555 ( Dec. 2000 ) PRINTED IN U.S.A. SYMPTOM POSSIBLE CAUSE Inadequate rinse or rinse water 1. Dirty line strainer causing reduced water flow. Turn off water supply, temperature is too low. remove strainer cap, withdraw and clean screen. Reassemble. 2. Low supply line pressure. 3. Excessive mineral deposits throughout wash and rins[...]