Go to page of
Similar user manuals
A good user manual
The rules should oblige the seller to give the purchaser an operating instrucion of Hobie 18 SX, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.
What is an instruction?
The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Hobie 18 SX one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.
Unfortunately, only a few customers devote their time to read an instruction of Hobie 18 SX. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.
What should a perfect user manual contain?
First and foremost, an user manual of Hobie 18 SX should contain:
- informations concerning technical data of Hobie 18 SX
- name of the manufacturer and a year of construction of the Hobie 18 SX item
- rules of operation, control and maintenance of the Hobie 18 SX item
- safety signs and mark certificates which confirm compatibility with appropriate standards
Why don't we read the manuals?
Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Hobie 18 SX alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Hobie 18 SX, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Hobie service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Hobie 18 SX.
Why one should read the manuals?
It is mostly in the manuals where we will find the details concerning construction and possibility of the Hobie 18 SX item, and its use of respective accessory, as well as information concerning all the functions and facilities.
After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.
Table of contents for the manual
-
Page 1
[...]
-
Page 2
WELCOME T O THE HOBIE W A Y OF LIFE Congratulations on the purchase of your new HOBIE 18’ and welcome to the HOBIE® sailing family. The HOBIE 18 cannot be outgrown. A single adult can sail it at top performance - and a crew of four can cruise in comfort. We offer this manual as a guide to increased safety and enjoyment of your new boat. The purp[...]
-
Page 3
1 This assembly manual takes you step- by-step through the setting-up and sailing of your new HOBIE 18. This manual will help you understand each part in det ail. Note that this manual applies for both Hobie 18 SE and SX models. Setting up your HOBIE 18 P AGE Packaging Layout ................................. 2 Framing the Hulls ...................[...]
-
Page 4
2 Packaging Layout 1. Port Hull 2. Starboard Hull 3. Back Bar 4. Boom 5. Tiller Cross Bar 6. Front Bar 7. Battens 8. Rigkit Box #1 9. Rigkit Box # 2 10. Rudders 11. Daggerboards 12. Sail Main and Jib 13. Trampoline 14. Mast (not shown) Hobie Cat 18 SE Rig Kit Box #1 (fig 2) Description Quantity 1. Shrouds, Forestay 2,1 2. 7/16” Mainsheet 48’ 1 [...]
-
Page 5
3 Framing the Hulls (Recommend two people) Tools- HEX wrench (provided) and a screwdriver with a 1 /4" head. Retaining Channel 8 Front Bar Inboard Bolt 3 3/4" 2 Front Bar Outboard Bolt 2" 2 Rear Cross Bar Inboard Bolt 2 1/ 2" 2 Rear Cross Bar Outboard Bolt 2" 2 Lock Nuts for 802-359 Outboard Bolts 4 1. Place the boxes on le[...]
-
Page 6
11. Install all four outboard bolts in the manner described in step 10. To insert the bolts in the front corner castings it will be necessary to remove the cover plates. Be careful when extracting the cover plate retaining screw. It is made of aluminum and can be galled. See Figure 6. 12. Use the hex drive to tighten the bolts. Follow this order to[...]
-
Page 7
Figure 9 Figure 8 5[...]
-
Page 8
6 5. Insert the aft outboard corner of the trampoline into the extrusion on the inside of the hull and pull the trampoline as far aft as it will go. 6. Repeat steps 2-5 for installing the starboard trampoline. 7. In front of the rear cross bar there is a hole in either inboard rail. Insert the port aft lacing line into this hole on the port hull an[...]
-
Page 9
7 MAST ASSEMBL Y 1. Support mast at both ends on saw horses or other such devices. Ref: Illus. #1, Pg. 20. 2. Spreaders. In the rig kit you will find all the parts of the spreader assembly. 3. The larger of the two pairs of aluminum rods (1-1), is the spreader arm. Attach it to the aft tab of the spreader root (1-2). Use a 3/16" x 11/16" [...]
-
Page 10
8 19. Slip the port diamond wire into the tip of the port spreader arm. Make sure that the anti-chafing roller on the diamond wire is above the spreader tip. Secure the diamond wire by installing one of the long cotter pins (1- 8) through the tip of the spreader. 20. Repeat this procedure for the starboard diamond wire. 21. Tighten the nut (1-15) o[...]
-
Page 11
STEPPING THE MAST . DANGER - Do not attempt to step the mast in an area of low overhead wires. A mast contacting an electrical wire could be fatal. 1. Secure the four trapeze wires near the bottom of the mast so that they will be out of the way while the mast is being raised. 2. Attach the jib halyard line to each end of the jib halyard wire to for[...]
-
Page 12
4. With the hinge in place over the step insert the mast step pin through the entire assembly so that it is visible on the opposite side on the hinge. 5. Attach the bridle wires to the bow tangs. Attach the roller furler mechanism between the bridle wires. Make sure the oblong hole in the roller furler is aft. See Figure 18. 6. Attach the port shro[...]
-
Page 13
13. Lace it through the rope lock and then through the thimble at the end of the trapeze wire. Now tie the line onto either end of the dogbone. See Figure 23. 14. Repeat this process for the other three trapeze wires at the respective locations. BOOM INST ALLA TION 1. Attach the gooseneck pin which extends from the front of the boom to the goosenec[...]
-
Page 14
Hobie 18 and SX18 UPDA TES INSTALLING THE RUDDER ASSEMBLY The rudders were updated after 1987. The newer rudders use a black plastic cam to lock the rudder in the down position. Locate the left and right rudder assemblies. The left one has a red dot and the right one a green dot. The tiller arms should have a slight bow towards the centerline of th[...]
-
Page 15
13 RUDDER AND TILLER CROSS BAR INST ALLA TION (Pre 1987 boat s) 1. Disengage the tiller arm from the lower casting and lock the tiller arm and rudder in the kicked up position. This will pull the rudder blade up and out of the way so the rudder pin can be installed. 2. Hold the lower casting up to the transom of the boat and fit the casting over th[...]
-
Page 16
14 RAISING THE SAILS 1. Point the boat into the wind before you begin this operation. 2. Lay the main sail out on the trampoline. Insert the battens into the batten pockets starting at the top of the sail and working your way down. The batten has a tip on each end. The end without any holes goes into the sail first. Slip the batten in until it seat[...]
-
Page 17
10. Attach the three boom blocks to the hangers on the boom. Secure the ratchet block to the top of the traveler car. Thread the mainsheet through the blocks as shown in Figure 37. Slip the other end of the mainsheet through the traveler jam cleat, then guide the line through the center of the traveler, and secure at the dead eye on the back bar. 1[...]
-
Page 18
16 Raising the Jib 1. Attach the shackle on the end of the jib halyard wire to the head of the jib. 2. Wrap the luff pocket of the jib around the forestay and engage the zipper an inch or so. Next thread the jib halyard line inside the luff pocket. See Figure 38. 3. Raise the sail by pulling on the jib halyard line and at the same time advance the [...]
-
Page 19
DAGGER BOARDS 1. Slip the shock cord through the hole in the upper portion of the dagger board, take both ends to the hole on the out board deck flange. Pass both ends through the hold and tie a knot under the rail. 2. Pass the rope handle through the same hole in the dagger board as before. Tie the two ends together to form a large loop which will[...]
-
Page 20
HOBIE CA HOBIE CA T 18 T 18 ’ ’ 18[...]
-
Page 21
19 INDEX NO. DESCRIPTION 1 Arm 2 Brace 3 Slide 4 Diamond Wire (one side) 5 Gooseneck Y oke 6 Check Block 7 Mast Rotation Line 8 Modified Swivel Block 9 Shackle 10 Mast Rotation Assembly 1 1 Pin-Pawl Bearing, 5.5. 12 Ring-Halyard Line 13 Hook for Halyard Lock Assembly 14 Jib Furling Assembly 15 Bridle Wire Assembly 16 Screw - 5.5. (1/4 x 20) 17 Back[...]
-
Page 22
20 Illustration No. 1 Mast Assembly 1-1 Spreader Arm 1-2 Spreader Root 1-3 Clevis Pin 3/16" x 11/16" 1-4 Slide 1-5 Clevis Pin 3/16" x 13/16" 1-6 Brace 1-7 Clevis Pin 3/16" x 9/16" 1-8 Cotter Pin 1-9 Mast Rotation Control Yoke 1-10 Block 1-11 Shackle 1-12 Bolt 4-1/8" Lg. 1-13 Diamond Wire 1-14 Mast Base Assembly 1-[...]
-
Page 23
21 Illustration No. 2 Jib Halyard Assembly 2-1 Jib Block Housing 2-2 Jib Halyard Wire 2-3 Luff Tensioner 2-4 Jib Halyard Line 2-5 Jib Block Sheave 2-7 Clevis Pin 2-8 A Cotter Pin 2-9 Swedge 2-10 Thimble 2-11 Block 2-12 Shackle Illustration No. 3 Tiller Connector Kit 3-1 Bolt 3-2 Half Ball 3-3 Tiller Crossbar 3-4 Plastic Washer 3-5 Tiller Arm 3-6 Wa[...]
-
Page 24
22 *Rudder system Pre-1987 shown Illustration No. 6 Rudder Assembly 6-1 Rudder Blade-Drilled 6-2 Lower Rudder Casting Assembly 6-3 Port Upper Rudder Housing Assembly 6-4 Nut Nylock 6-5 Bolt 2" Lg 6-6 Spring 6-7 Delrin Screw 6-8 1 / 4" I.D. Nyliner 6-9 Rudder Cam 6-10 Upper Rudder Housing Casting 6-11 Rivet 6-12 Locking Sleeve 6-13 Pin Upp[...]
-
Page 25
Illustration No. 8 T raveler Assembly 8-1 1- 1/4" Lg H.H. Bolt 8-2 Deck Plate 8-3 Sheave 8-4 Spacer 8-5 Car Assembly 8-6 Cotter Pin 8-7 H.H. Nuts-Nylock 8-8 Bearing Cylinder 8-9 Pin-Clevis 8-10 Bearing Ball Illustration No. 9 Roller Furler Assembly 9-1 Upper Retaining Ring 9-2 Top Nyliner 9-3 Bottom Nyliner 9-4 Yoke 9-5 Housing 9-6 Interior Re[...]
-
Page 26
Illustration No. 10 (old style) Dolphin Post Assembly 10-1 Screw RHMS 10-2 Internal Lock Washer 10-3 Washer 10-4 Mast Step Pad 10-5 Bushing 10-6 Mast Step Casting 10-7 Dolphin Striker Post 10-8 Dolphin Striker Sleeve Illustration No. 1 1 (new style) Dolphin Post Assembly 11-1 Screw RHMS 11-2 Washer 11-3 Bearing 11-4 Mast Step Casting 11-5 Dolphin S[...]
-
Page 27
Illustration No. 12 (new style) Tiller Connector 12-1 Tiller Connection Rod 12-2 Tiller Arm Swivel End Cap 12-3 Tiller Arm Insert 12-4 Bolt 12-5 Washer 12-6 Insert Bearing 12-7 Retainer Clip 12-8 Screw Part s Relating to Diagram on Page 2 11 Trapeze Seat Assy. 2 Trapeze Seat 2 Trapeze Hook 2 Trapeze Lacing Line 6' 12 Mast Rotation Control Yoke[...]
-
Page 28
26 SAILING YOUR HOBIE 18’ Safe and sane guideline for the beginner; and an easy review for the experienced. Always wear a life jacket when boating. BALANCING THE BOAT When sailing, sit on the upwind side of the boat (wind on your back) just in front of the tiller, facing the sail. Balance your weight further outboard as the boat begins to tip or [...]
-
Page 29
27 TURNING To tack or turn the boat into and across the wind to the opposite direction (also known as "coming about"), follow the points of sail guide illustration and take the boat to the close hauled point of sail. This is when you are nearly 35 degrees from sailing straight into the wind. With the boat moving forward and not stalling, [...]
-
Page 30
28 line while slowly leaning back away from the trampoline. Lean to approximately 45 degrees for best leverage. As the mast and sail lift out of the water and the upper hull begins to drop back into the water, drop down to your knees then into the water. Hold onto the righting line near the crossbar or the crossbar itself near the hull that you wer[...]
-
Page 31
29 6) Hobie Cat rudder blades are preset to break away from the locked down position at 17-26 pounds by testing with a line around the rudder blade seven inches above the lowest tip of the blade. Once the rake is changed, the breakaway tension should be rechecked. The tension may be adjusted by turning the 3/4" internal screw in the housing. T[...]
-
Page 32
A good anti-fouling paint can be applied for some protection from marine growth before mooring. Before painting, it is suggested that the area be masked off to ensure a clean line. No friction reducing paints or agents may be employed on a Hobie Cat during competition. HOBIE CLASS ASSOCIATION The Hobie Class Association was started by a group of Ho[...]
-
Page 33
About your Hobie 18’ There are ways of going faster on a catamaran, while still staying within the eight foot beam, trailerable size range. Basically, you put a taller mast on, use daggerboards, and go to a half round hull shape. The Hobie 18 is the end result of our efforts - mine, Phil Edwards' (my longtime friend and co-designer of the 18[...]
-
Page 34
CA UTION / SAFETY TIPS • Watch for overhead power lines. Never rig, trailer or sail the boat near overhead power lines. Contact with a power line could be fatal. • Install Drain Plugs. Even the most experienced of boaters forget to install the drain plugs sometimes. When installing the plugs, be sure that the threads and gaskets are free of san[...]