English dropdown-ico

Holland Hitch XL-FW232-02 manual

1
2
3
4
5
6
7
8
9
10
11
12

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Holland Hitch XL-FW232-02, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Holland Hitch XL-FW232-02 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Holland Hitch XL-FW232-02. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Holland Hitch XL-FW232-02 should contain:
- informations concerning technical data of Holland Hitch XL-FW232-02
- name of the manufacturer and a year of construction of the Holland Hitch XL-FW232-02 item
- rules of operation, control and maintenance of the Holland Hitch XL-FW232-02 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Holland Hitch XL-FW232-02 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Holland Hitch XL-FW232-02, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Holland service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Holland Hitch XL-FW232-02.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Holland Hitch XL-FW232-02 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    XL-FW232-02 GO THE DIST ANCE. FIF TH WHEELS HITCH XA-71 Series Fifth Wheel T op Plates TROUBLESHOOTING AND REBUILD PROCEDURES XA-71-DA 2” SAE Kingpin (Rebuild Kit RK-65014) XA-71-DA-03705 2” SAE Kingpin for FW2570-7103 SERIES or FW2570-7113 SERIES - RK-65014-1 XA-71-OA-03713 3 1 ⁄ 2 ” SAE Kingpin for FW2570-7103 SERIES or FW2570-7113 SERIES[...]

  • Page 2

    2 XL-FW232-02 TROUBLESHOOTING HINTS Fifth Wheel is Hard to Hook Up to T railer: ✔ POSSIBLE CAUSE REMEDY ■ ■ The trailer may be too high; the kingpin Lower the trailer landing gear . is not entering the locks properly . ■ ■ Locks are closed. Pull the secondary and primar y release handles to the unlocked position and force the hinged lock [...]

  • Page 3

    XL-FW232-02 3 1 XA-71-D 1 Fifth wheel top plate for 2 ˝ kingpin 1A XA-71-O 1 Fifth wheel top plate for 3.5 ˝ kingpin 1B XA-71-03706 1 Fifth wheel top plate - 2 ˝ kingpin for FW2570-7103 series or FW2570-7113 series only 1C XA-03711 1 Fifth whl. top plate - 3.5 ˝ kingpin for FW2570-7103 or FW2570-7113 series only 2 XB-5 1 Cotter pin 1/4 ˝ x 2 ?[...]

  • Page 4

    4 XL-FW232-02 REBUILDING PROCEDURES 1. Before attempting to rebuild, review each trouble- shooting hint on page 2 of this manual. Y ou may find that rebuilding is not necessary . 2. If rebuilding is required, check the front page of this manual to be sure you have the correct kit for the fifth wheel you are about to rebuild. 3. T otally disassemble[...]

  • Page 5

    Plunger and Adjustment Wedge Installation 1. Install the adjusting screw ( 20 ) through the hole locat- ed in the throat of the fifth wheel casting. Install the compression spring ( 23 ) over the screw , then slide the adjusting wedge ( 22 ) over the screw (see FIGURE 6 ). Compress the spring and install a lock nut ( 21 ). T ighten the screw with a[...]

  • Page 6

    6 XL-FW232-02 REBUILDING PROCEDURES continued Release Arm and Release Lever Installation 1. Check the fit of the release lever ( 15 ) inside the slot in the plunger ( 17 ). The rounded end of the release lever must fit freely into the slot in the plunger . If the parts do not fit together freely , it will be necessar y to deburr the rounded end of [...]

  • Page 7

    XL-FW232-02 7 REBUILDING PROCEDURES continued Swinging Lock Installation 1. Place the swinging lock ( 6 ) into position, compressing spring ( 7 ). For spring position, see FIGURE 3 . NOTE: The lock pin ( 5 ) has a hole for a grease fitting ( 25 ). Position the pin so that the hole faces the front of the casting. Drive the lock pin ( 5 ) through the[...]

  • Page 8

    8 XL-FW232-02 REBUILDING PROCEDURES continued Adjust the Fifth Wheel Locks: 1. Using a ratchet with 1/2˝ Allen wrench, tighten the adjustment screw ( 20 ) in the throat in the fifth wheel, by turning the screw clockwise until tight. 2. Check that the kingpin on the lock tester is square to the swinging lock ( 6 ) and that the stationary lock is sq[...]

  • Page 9

    XL-FW232-02 9 CHECKING THE OPERA TION OF THE FIFTH WHEEL continued Check the Mounting Brackets Before Remounting the T op Plate: 1. Inspect the brackets for cracks or damage, and replace if necessary . 2. Check the rubber bushings for wear . Replace if necessary . 3. Apply grease to the top bearing surface of the mounting bracket before remounting [...]

  • Page 10

    10 XL-FW232-02 T AB ON SWING LOCK LOCK ARM WITH STEP END NO ADJUSTMENT BLOCK AL TERNA TIVE “SECONDARY LOCK INST ALLA TION” FIGURE A ADJUSTMENT BLOCK .25 B 3/16 ± 1/16 A FIGURE B For fifth wheel models ORIGINALL Y equipped with a tab on the swing lock and a step end on the lock arm, follow the instructions below and refer to FIGURE A , at right[...]

  • Page 11

    XL-FW232-02 11[...]

  • Page 12

    12 XL-FW232-02 HOLLAND USA, INC. 1 950 Industrial Blvd. • P .O. Box 425 • Muskegon, MI 49443-0425 Phone 888-396-6501 • Fax 800-356-3929 www .thehollandgroupinc.com Copyright © August 2002 • The Holland Group, Inc. Holland USA, Inc. Facilities: Denmark, SC Muskegon, MI Dumas, AR Warrenton, MO Holland, MI Wylie, TX Ph: 888-396-6501 Fax: 800-[...]