Go to page of
Similar user manuals
-
Automobile
Honda Power Equipment CRF250X'04
118 pages 2.45 mb -
Heat Pump
Honda Power Equipment WB30XT
63 pages 5.68 mb -
Water Pump
Honda Power Equipment WT30X
64 pages 1.87 mb -
Water Pump
Honda Power Equipment WA15
7 pages 1.61 mb -
Water Pump
Honda Power Equipment WT40X
64 pages 1.87 mb -
Water Pump
Honda Power Equipment WB15
31 pages 0.61 mb -
Car Stereo System
Honda Power Equipment S2000
21 pages 0.67 mb -
Automobile Parts
Honda Power Equipment BFP8D/9.9D
108 pages 3.28 mb
A good user manual
The rules should oblige the seller to give the purchaser an operating instrucion of Honda Power Equipment L14-20R, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.
What is an instruction?
The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Honda Power Equipment L14-20R one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.
Unfortunately, only a few customers devote their time to read an instruction of Honda Power Equipment L14-20R. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.
What should a perfect user manual contain?
First and foremost, an user manual of Honda Power Equipment L14-20R should contain:
- informations concerning technical data of Honda Power Equipment L14-20R
- name of the manufacturer and a year of construction of the Honda Power Equipment L14-20R item
- rules of operation, control and maintenance of the Honda Power Equipment L14-20R item
- safety signs and mark certificates which confirm compatibility with appropriate standards
Why don't we read the manuals?
Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Honda Power Equipment L14-20R alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Honda Power Equipment L14-20R, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Honda Power Equipment service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Honda Power Equipment L14-20R.
Why one should read the manuals?
It is mostly in the manuals where we will find the details concerning construction and possibility of the Honda Power Equipment L14-20R item, and its use of respective accessory, as well as information concerning all the functions and facilities.
After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.
Table of contents for the manual
-
Page 1
Your new Emer Gen Switch will prov id e you with a wa y to safely utilize your generator power through your existing el ectrical wiring during a power outage. You’ll install your switch next t o your home’s e lectrical panel load center and then you’ll connect circ uit br eaker wires to the transfer switch’s circuits. Once you power up your[...]
-
Page 2
2 SAFETY INFORMATI ON 1. The National Electrical Code states the connection of a generator to any electrical circuit normally powered by an electrical utility, must be by means of an approved transfer switch so as to isolate the electrical circuit from the utility system when the generator is operating. Your EmerGen Switch is approved by a National[...]
-
Page 3
3 INSTALLATION INSTRUCTIONS 1. Determine where you want your EmerGen Switch located, either to the left or right of the load center. The switch should be approximately 18” from the center of the load center, making sure that there is plenty of room to properly conne ct the flex conduit whip. 2. TURN OFF POWER. The main circuit breaker in your loa[...]
-
Page 4
4 W iring the EmerGen Switch to the Load Center 1. From your plan, locate the circuit breaker that is to be connected to the EmerGen Switch circuit “A”. Turn that circuit breaker to the OFF position. Loosen the lug securing the wire and remove the wire. WARNING: Your generator must be properly grounded and the neutral un-bonded at the generator[...]
-
Page 5
5 Installing 240 V olt (2 pole) Circuits EmerGen Switch products provide circuits for the connection of 240 volt appliances that are connected to 2 pole branch circuit breakers in your load center. These EmerGen Switch circuits fo r 240 volt operation have a handle tie included with the switch that ties two circuit selecto r switches C & D toge[...]
-
Page 6
6 Completing the Installation 1) When the preceding steps have been completed for all desired circuits, the EmerGen Switch white (neutral) wire(s) needs to be installed. a. Select any unused hole on the neutral bar in the load center. b. Cut and strip the wire appropriately. Insert the wire into the hole and tighten securely. 2) The EmerGen Switch [...]
-
Page 7
7 Operation / T est Procedur e 1. Switch positions should remain in the “LINE” position under normal utility power. The “OFF” position is generally not used. The “GEN” positions are used when connecting circuits to your generator power source. 2. When testing and/or switching to generator power after a p ower outage, ensure all switches[...]
-
Page 8
8 P robl em C ause S ol uti on Generator i s runni ng but no A C output i s avai l able. 1. Generator ci rcui t breaker has t ri pped. 1. Res et ci rcui t breaker. 2. P oor connecti on or defecti ve cord set. 2. Check and repai r. 3. Connected devi ce i s bad. 3. S el ect a di f f erent l oad or appl i ance that i s i n goo d condi ti on. 4. Faul t[...]