Honda BF2.3D (2014) manual

00X31-ZW6-6300 BF2.3D Cover1-4 PANTONE 288CVC DIC F101 Black 31ZW6630 00X31-ZW6-6300 K2 N 2eY1 1000.2011.10 Printed in China Includes US and Canadian Models BF2.3D 00X31-ZW6-6300_BF2.3D_Cover(AH).1 1 00X31-ZW6-6300_BF2.3D_Cover(AH).1 1 2011/09/17 18:28:18 2011/09/17 18:28:18 Click to Save As[...]

Keep this Owner ’ s Manual handy , so you can refer to it at any time. This Owner ’ s Manual is considered a permanent part of the outboard motor a nd should remain with the outboard motor if resold. © 2013 Honda Mot or Co., Ltd. – All Rights Reserved The information and specifications included in this publication were in ef fect at the time[...]

1 INTRODUCTION Congratulations on your selection of a Honda outboard motor . W e are certain you will be pleased with your purchase of one of the finest outboard motors on the market. W e want to help you get the best results from your new outboard motor and to operate it safely . This manual contains information on how to do that; please read it c[...]

2 INTRODUCTION A FEW WORDS ABOUT SAFETY Y our safety and the safety of others are very important. And using this outboard motor safely is an important responsibility . T o help you make informed decisions ab out safety , we have prov ided operating procedures and oth er information on labels and in this manual. This information alerts you to potent[...]

CONTENTS 3 OUTBOARD MOTOR SAFETY ................... ................ 6 IMPORTANT SAFETY INFORMATION .............. 6 SAFETY LABEL LOCATIONS ................... ........... 8 CONTROLS AND FEATURES ..................... .............. 11 CONTROL AND FEATURE IDENTIFICATION CODES ............................... 11 COMPONENT AND CONTROL LOCATIO NS ... [...]

CONTENTS 4 OPERATION ................... ...................... ....................... 24 SAFE OPERATING PRECAUTIONS ................... 24 BREAK-IN PROCEDURE ............................ ......... 24 TRANSOM ANGLE ADJUSTMENT .................... 24 INFREQUENT OR OCCASIONAL USE .............. 25 STARTING THE ENGINE .................. .............[...]

CONTENTS 5 STORAGE .......... ....................... .................. .................. 53 STORAGE PREPARATION .................................. 53 Cleaning ..................... ....................... .................. 53 Fuel ................ ...................... .................. .............. 53 Adding a Fuel Stabilizer .............[...]

6 OUTBOARD MOT OR SAFETY IMPOR T ANT SAFETY INFORMA TION The Honda BF2.3D outboa rd motor is designed for use with boats that have a suitable manufacturer ’ s power recommendation. Other uses can result in injury to the operator or damage to the outboard motor and other property . Most injuries or property damage can be prevented if you follow al[...]

7 OUTBOARD MOTOR SAFETY Refuel With Car e • Gasoline is extremely flammable, and gasoline vapor can explode. Refuel outdoors, in a well-ventilated area, with the eng ine stopped. Never smoke near gasoline, and keep other flames and sparks away . • Refuel carefully to avoid spilling fuel. A void overfilling the fuel tank. • After refueling, ti[...]

8 OUTBOARD MOT OR SAFETY SAFETY LABEL LOCA TIONS US, Puerto Rico, and US V irgin Islands T ypes The labels shown here contain importan t safety information. Please read them carefully . These labels are considered permanent parts of your outb oard motor . If a label comes off or becomes hard to read, contact an authorized Honda Marine dealer for a [...]

9 OUTBOARD MOTOR SAFETY Canadian T ypes The labels shown here contain importan t safety information. Please read them carefully . These labels are considered permanent parts of your outb oard motor . If a label comes off or becomes hard to read, contact an authorized Honda Marine dealer for a replacement. HOT CAUTION READ OWNER’S MANUAL 31ZW66320[...]

10 OUTBOARD MOT OR SAFETY Canadian T ypes • Honda outboard motor is designed to give safe and dependable service if operated according to instructions. Read and understand the Owner’s Manual befor e operating the outboard motor . Failur e to do so could r esult in personal injury or equipment damage. • The engine system will be heated during [...]

11 CONTROLS AND FEA TURES CONTROL AND FEA TURE IDENTIFICA T ION CODES Refer to this chart for an explan ation of the T ype Codes used in this manual to identify c ontrol and feature applications. TYPE CODE (example) Model BF2.3D T ype SCHA SCHC LCHA LCHC Shaft Length S ● L ● Throttle Grip ● ● Centrifugal Clutch ● ● SC H A Destination A=[...]

12 CONTROLS AND FEA TURES CO MP O NENT A ND CO NTR O L L OCA TI O N S [LCH type is shown] EMERGENCY STOP SWITCH ST AR TER GRIP THROTTLE GRIP TILLER HANDLE EMERGENCY STOP SWITCH LANY ARD CLAMP SCREW TRANSOM ANGLE ADJUSTING BOL T AND WING NUT GEAR OIL LEVEL SCREW GEAR OIL DRAIN/FILL SCREW PROPELLER ANTIVENTILA TION PLA TE ANODE STEERING FRICTION BOL [...]

13 CONTROLS AND FEA TURES CONTROLS Emergency S top Switch Clip and Emergency S top Switch The emergency stop switch clip must be inserted in the emer gency stop switch in order for the engine to start and run. The emergency stop switch lanyard must be attached securely to the operator or to the operator ’ s PFD (Personal Flotation Devic e). When [...]

14 CONTROLS AND FEA TURES Thrott le Grip The throttle grip controls engine speed. An index mark on the tiller arm shows throttle position and is helpful for setti ng the throttle correctly when starting (p. 26 ). Throttle Grip Friction Knob The throttle grip friction knob adjusts resistance to throttle grip rotation. T urn the knob clockwise to inc[...]

15 CONTROLS AND FEA TURES Fuel V alve Lever The fuel valve opens and closes the passage between the fuel tank and the carburetor . The fuel valve lever must be in the ON position for the engine to run. When the engine is not in use, leave the fuel valve lever in the OFF position to prevent carbur etor flooding and to reduce the possibility of fuel [...]

16 CONTROLS AND FEA TURES T ransom Angle Adjusting Bolt The transom angle adjusting bolt is used to adjust the angle of the outboard motor in the normal operating position (see page 34 ). Loosen the wing nut to free the adj usting bolt. Adjust the angle of the outboard motor , and tighten the wing nut. Be sure that the bolt head and wing nut are se[...]

17 CONTROLS AND FEA TURES S teering Friction Bolt The steering friction bolt adjusts steering resistance. Less friction allows the outboard motor to turn more easily . More friction helps to hold a steady course while cruising or to prevent the outboard motor from swinging while trailering the boat. Clamp Screws Use the clamp screws to secure the o[...]

18 CONTROLS AND FEA TURES OTHER FEA TUR ES Centrifugal Clutch The centrifugal clutch automatically engages and transmits power when engine speed is increased above approximately 2,700 rpm. At idle speed, the clutch is disengaged. Oil Level Inspection Window Use the oil level inspection window to check the engine oil level with the engine stopped an[...]

19 INST ALLA TION Correct and secure installation is essential for safe boating and good performance. Follow the installation instructions provided in this manual. POWER REQUIREMENT S Before installation, check to be sure that the outboard motor does not exceed the recommended maximum horsepower for the bo at on which it is to be installed. Refer t[...]

20 INST ALLA TION When the outboard motor is installed extremely low , wate r may enter into the engine under case and negatively affect the performance and durability . When installing, check that the outboard motor is high enough from the water level to keep the engine under case from waves, splash, etc. when the engine is stopped with the boat f[...]

21 INST ALLA TION TRANSOM ANGLE ADJUSTMENT Use the transom angle adjusting bolt (p. 24 ) to adjust the angle of the outboard motor so the propeller is pe rpendicular to the surface of the water . 31ZW66320.book 21 ページ ２０１３年１０月４ 日　金曜日　午後３時４８分[...]

22 BEFORE OPERA TION ARE YOU READY TO GET UNDER W A Y? Y our safety is your responsibility . A little time spent in preparation will significantly reduce your risk of injury . Knowledge Read and understand this manual. Know what the controls do and how to operate them. Familiarize yourself with the outboard motor and its operation before you get un[...]

23 BEFORE OPERA TION Maintenanc e Inspection • Check the engine oil level (p. 42 ). Running the engine with a low oil level can cause e ngine damage. • Check to be sure the propeller is un damaged (p. 52 ). • Check that the anode is securely attached to the antiventilation plate (p. 51 ) and is not excessively worn. The anode helps to protect[...]

24 OPERA TION SAFE OPERA TING PRECAUTIONS T o safely realize the full potential of this outboard motor , you need a complete understanding of its operation and a certain amount of practice with its controls. Before operating the outboard motor for the first time, please review the IMPORT ANT SAFETY INFORMA TION on page 6 and the chapter titled BEFO[...]

25 OPERA TION INFREQUENT OR OCCASIONAL USE If your outboard motor will be used on an infrequen t or intermittent basis, please refer to the fuel section of the STORAGE chapter (p. 53 ) for additional information regarding fuel de terioration. ST AR TING THE ENGINE 1. Put the emergency stop switch cli p in the emergency stop switch, and attach the e[...]

26 OPERA TION 3. Move the fuel valve lever to the ON position. 4. Move the throttle grip to the ST AR T position. Do not start the engine with the thrott le grip in the F A ST position, or the boat will move suddenly when the engine starts. FUEL V AL VE LEVER ON THROTTLE GRIP ST AR T 31ZW66320.book 26 ページ ２０１３年１０月４ 日　金[...]

27 OPERA TION 5. T o start a cold engine, pull the choke knob to the ON position. T o restart a warm engine, leave the choke knob in the OFF position. 6. Pull the starter grip lightly until you fe el resistance, then pull briskly in the direction of the arrow as shown above. Return the starter grip gently . 7. If the chok e knob was pulled to the O[...]

28 OPERA TION EMERGENCY ST AR TING If the recoil starter is not working properly , you can start the engine manually using the emergency starter rope that came with your outboard motor . 1. Remove the en gine cover . 2. Remove the three 5 mm nuts with an 8 mm wrench and remove the recoil starter . 3. Set the controls the same as for no rmal startin[...]

29 OPERA TION 5. Pull the emer gency starter rope slowly until resistan ce is felt, then pull briskly . Keep away from moving parts while pulling the rope. If necessary , rewind the rope and pull again. If the engine does not star t after several attempts, refer to T AKING CARE OF UNEXPECTED PROBLEMS, p. 58 . 6. If the choke was used to start the e[...]

30 OPERA TION STOPPING THE ENGINE Emergency Engine S topping T o stop the engine in an emergency , pull the emergency stop switch clip out of the emer gency stop switch by pulling the emer gency stop switch lanyard. W e suggest that you stop the engine this way occasionally to verify that the engine and em er gency stop switch are operating properl[...]

31 OPERA TION 3. Move the fuel valve lever to the OFF position. 4. Close the fuel tank vent by turn ing the vent knob OFF position. THROTTLE OPERA TION Use the throttle grip friction knob to help hold a constant throttle setting while cruising. T urn the knob clockwise to increase thrott le grip friction for holding a constant speed. T u rn the kno[...]

32 OPERA TION REVERSING THE OUTBOARD MOTOR Important Safety Precautions • Befor e rotating the outboar d motor (fr om either for war d to r everse or fr om r everse to forwar d) reduce the engine speed to SLOW , or the boat could capsize. • When operating in r e verse, pr oceed with caution to avoid hitting any underwater obstructions with the [...]

33 OPERA TION 2. T o reverse dire ction, turn the outboard motor 180°, and th en pivot the tiller handle as shown. Be careful not to hold and move the throttle grip when pivoting the tiller handle. STEERING Steer by moving the tiller handle opposite the direction yo u want the boat to turn. Use the steering friction bolt to help hold a ste ady cou[...]

34 OPERA TION CRUISING Engine Speed For best fuel economy , limit the throttle opening to 80%. Use the throttle friction cont rol (p. 32 ) to help you hold a steady speed. For rough water conditions or lar g e waves, slow down to prevent the propeller from rising out of the water . T ransom Angle Install the outboard motor at the best transom angle[...]

35 OPERA TION MOORING , BEACHING, LAUNCHING T o raise the outboard motor out of the water while the boat is moored, or for maximum clearance when beaching or launching, tilt the outboard motor to the 75° position. Stop the engine before tilti ng the outboard motor . The 75° position is not an operating position. 1. Stop the engine and turn the fu[...]

36 OPERA TION 5. T o return the outboard motor to the normal running position, hold the outboard motor by th e front carrying handle on the engine case and pull the tilt leve l toward you, and then lower the outboard motor slowly . T o avoid damaging the outboar d motor , be very car eful when moor ing a boat, especially when its outboar d motor is[...]

37 SER VICING YOUR OUTBOARD MOTOR THE IMPOR T ANCE OF MAINTENANCE Proper maintenance is essential for safe, economical, and trouble-free operation. It will also help reduce air pollution. T o help you properly care for y our outboard motor , the following pages include a maintenance schedule, routine inspection procedures, and simple maintenance pr[...]

38 SER VICING YOUR OUTBOARD MOTOR MAINTENANCE SAFETY Some of the most important safety precautions follow . However , we cannot warn you of eve ry conceivable hazard that can arise in performing maintenance. Only you can decide whether or not you should perform a given task. Safety Precautions • Make sure the engine is off before you begin any ma[...]

39 SER VICING YOUR OUTBOARD MOTOR TOOL KIT AND EMERGENCY ST AR TER ROPE The following tools ar e supplied with the outboard motor for simple maintenance procedures and emer gency repairs. An emergency starter rope is also supplied. Keep these items on the boat so that they will always be available if you need them. If your tool kit needs replacemen[...]

40 SER VICING YOUR OUTBOARD MOTOR MAINTENANCE SCHEDULE Follow the MAINTENANCE SCHEDULE table and service your outboard motor accordingly . Please note, a claim for warranty coverage will not be denied simply because the maintenance schedule for your outboard motor was not followed. However , any part(s) that fails specifically due to lack of mainte[...]

41 SER VICING YOUR OUTBOARD MOTOR (1) Lubricat e more frequently when used in sa lt water . (2) These items should be serviced by your servicing dealer , unless you have the proper tools an d are mechanically proficient. R efer to the Honda shop manual for serv ice procedures. See “Honda Publications” on page 71 for orderin g information. (3) F[...]

42 SER VICING YOUR OUTBOARD MOTOR ENGINE COVER REMOV AL AND INST ALLA TION The engine cover retaining strap fastens the engine cover to the outboard motor . T o remove the engine cover , unhook th e engine cove r reta ining strap, then lift the engine cover of f the outboard motor . T o install the engine cover , place the cover on the outboard mot[...]

43 SER VICING YOUR OUTBOARD MOTOR When you check the oil level in the oil level inspection window , you might notice the engine oil appears milky or the oil level has increased. If you notice either condition, change the engine oil. See the following table for an explanation of these conditions. Operating Method Result Effe ct Running the engine be[...]

[...]

45 SER VICING YOUR OUTBOARD MOTOR Gear Case Oil Change Change the gear case oil with the engine stopped and the outboard motor in the vertical position. 1. Place a suitable container below the oil drain hole to catch the used oil, then remove the o il level screw and oil drain/fill screw . 2. Allow the used oil to drain completely , then install an[...]

46 SER VICING YOUR OUTBOARD MOTOR Apply Honda Marine Corrosion Inhibitor (or equivalent) to all areas under the engine cover and any exposed metal surfaces. Lubrication Points Apply Honda Marine waterproof grease to the parts shown below: Lubrication interval: 10 operating hours or o ne month after the date of p urchase or initial use, then every 5[...]

47 SER VICING YOUR OUTBOARD MOTOR Spark Plug Service RECOMMENDED SP ARK PLUG: CR4HSB (NGK) U14FSR-UB (DENSO) Incorr ect spark plug can cause engine damage. 1. Remove the en gine cover (p. 42 ). 2. Disconnect the spark plug cap from the sp ark plug. 3. Remove th e spark plug with a spark plug wrench and screwdriver . 4. Inspect the spark plug. Repla[...]

48 SER VICING YOUR OUTBOARD MOTOR 6. Install the spark plug carefully , by hand, to avoid cros s-threading. 7. After the spark plug seats, tighten w ith a spark plug wren ch to compress the sealing washer . If reinstalling the used spark plug, tighten 1/8 – 1/ 4 turn after the spark plug seats. If installing a new spark p lug, tighten 1/2 turn af[...]

49 SER VICING YOUR OUTBOARD MOTOR REFUELING FUEL T ANK CAP ACITY : 0.29 US gal (1.1 L) W ith the engine stopped, turn the vent knob ON position to open the fuel tank vent, then remove the fuel filler cap. Refill the fuel tank if the fuel level is low . Refuel in a well-ventilated area. Fill the tank to the maximum fuel level. After refueling, in s [...]

50 SER VICING YOUR OUTBOARD MOTOR FUEL RECOMMENDA TIONS Use unleaded gasoline with a pump octane rating of 86 or higher . Y our outboard motor is certified to operate on unleaded gasoline with an octane ratin g of 86 or higher . Never use stale or contaminated gasoline or an oil/gasoli ne mixture. A void getting dirt or water in the fuel tank. Y ou[...]

51 SER VICING YOUR OUTBOARD MOTOR Recoil S tarter Rope Inspection Inspect the recoil starter rope, and replace it if it becomes frayed. Always keep the emergency starter rope on the boat in case the recoil starter rope fails. Anode Replacement The anode is made of a sacrificial material that helps to protect the outboard motor from corrosion. Repla[...]

52 SER VICING YOUR OUTBOARD MOTOR Propeller Replacement Before replacing the propeller , remove the emergency stop switch clip from the emer gency stop switch to prevent any possibility of the engine being st arted while you are working with the propeller . The propeller blades may have sharp edges , so wear heavy gloves to protect your hands. Oper[...]

53 ST ORAGE STORAGE PREP ARA TION Proper storage preparation is e ssential for keeping your outboard mo tor trouble-free and looking good. The following steps will help to keep rust and corrosion from impairing your outboard motor ’ s function and appearance, and will make the engine easier to start when you use the outboard motor again. Cleaning[...]

54 STORAGE Adding a Fuel S tabilizer When adding a fuel stabilizer , fill the fuel tank with fresh gasoline. If only partially filled, air in the tank will promote fuel deterioration d uring storage. If you keep a container of gasoline for refueling, be sure that it contains only fresh gasoline. 1. Add Honda Marine fuel stabilizer foll owing the in[...]

55 ST ORAGE 2. W ith the engine stopped, turn the vent knob ON po sition to open the fuel vent, and then remove the fuel filler cap. 3. Loosen the carbureto r drain screw an d move the fue l valve lever to th e ON position to drain th e carburetor and the fuel tank into an approved gasoline container . 4. After draining is completed, tighten the ca[...]

56 STORAGE If storing horizontally , be sure to fold the tiller handle, and rest the outboard motor on its case protectors. Any other horizontal storage position may cause damage to th e outboar d motor or oil leakage. Cover the outboard motor to keep out dust. Do not us e plastic sheet as a dust cover . A nonporous cover will trap moisture, promot[...]

57 TRANSPOR TING WITH OUTBOARD MOTOR INST ALLED ON BOA T When trailering a boat with the outboard motor attached, leave the engine in the normal running position, if possible, and tighten the steering friction bolt securely (p. 33 ). If there is insufficient road clearance in the normal runn ing position, then tilt the outboard motor and use a moto[...]

58 T AKING CARE OF UNEXPECTED PROBLEMS ENGINE WILL NOT ST AR T Possible Cause Correction Clip not inserted in emer gency stop switch. Insert clip in emer gency stop switch. Choke knob in OFF position. Pull choke knob to ON pos ition, unless engine is warm (p. 27 ). Throttle grip not in ST AR T position. T urn throttle grip to ST AR T position (p. 2[...]

59 T AKING CARE OF UNEXPECTED PROBLEMS ENGINE WILL NOT ST AR T Possible Cause Correction Out of fuel. Refuel (p. 49 ). Fuel vent closed. Open the vent knob (p. 25 ). Fuel valve lever in the OFF posit ion. Move the fuel valve lever to the ON position (p. 26 ). Bad fuel; outboard motor st ored without treating or draining gasoline, or refueled with b[...]

60 T AKING CARE OF UN EXPECTED PROBLEMS HARD ST AR TING OR ST ALLS AFTER ST AR TING Possible Cause Correction Choke knob in OFF position. Pull choke knob to ON pos ition, unless engine is warm (p. 27 ). Throttle grip not in ST AR T position. T urn throttle grip to ST AR T position (p. 26 ). Fuel vent closed. Open the vent knob (p. 25 ). Bad fuel; o[...]

61 T AKING CARE OF UNEXPECTED PROBLEMS ENGINE WILL NOT DRIVE THE PROPELLER Possible Cause Correction Broken shear pin . Replace shear pin (p. 52 ). Damaged clutch, drive train, or engagement mechanism. T ake outboard motor to an authorized Honda Marine dealer , or refer to the shop manual. 31ZW66320.book 61 ページ ２０１３年１０月４ 日[...]

62 T AKING CARE OF UN EXPECTED PROBLEMS SUBMERGED OUTBOARD MOTOR A submerged outboard motor must be serviced immediately after it is recovered from the water in order to minimize corrosion. If there is a Honda Marine dealership nearby , take the outboard motor to the dealer immediately . If you are far from a deale r , proceed as follows : 1. Remov[...]

63 T AKING CARE OF UNEXPECTED PROBLEMS When cranking the engine with an open ignition cir cuit (spark plug r emoved from the ignition cir cuit), r emove the emer gency stop switch clip fr om the emergency stop switch to pr event possible damage to the ignition system. 5. Pour a teaspoon of engine oil into the sp ark plug hole, and then pull the sta[...]

64 TECHNICAL INFORMA TION Serial Number Locations Record the product identification number , the engine serial number , and the date of purchase in the space provided on this page. Y ou will need these numbers when ordering parts, and when making technical or warranty inquiries (p. 72 ). The product identification number is stamped on a pla te atta[...]

65 TECHNICAL INFORMA TION Carburetor Modif ication for High Altitude O peration At altitudes above 3,000 feet (900 meters), the standard carburetor air -fuel mixture will be too rich. Performance will decrease, and fuel consumption will increase. A very rich mixture will also foul the spark plug and cause hard startin g. Operation at an altitude th[...]

66 TECHNICAL INFORMA TION Emission Control System Information Source of Emissions The combustion process produces carbon monoxide, oxides of nitrogen, and hydrocarbo ns. Control of hydrocarbons and oxides of nitrogen is very important because, under certain conditions, they react to form photochemical smog when subjected to sunlight. Carbon monoxid[...]

67 TECHNICAL INFORMA TION Problems That May Affect Emissions If you are aware of any of the following symptoms, h ave your engine inspecte d and repaired by your servicing dealer . • Hard starting or stalling after star ting. • Rough idle. • Misfiring or backfiring under load. • Afterburning (backfir ing). • Black exhaus t smoke or high f[...]

68 TECHNICAL INFORMA TION St a r L a b e l US, Puerto Rico, and US V irgin Islands A Star label was applied to this outboard motor in accordance with the requirements of the California Air Resources Board. The S tar Label means Cleaner Marine Engine The Symbol for Cleaner Marine Engines: Cleaner Air and W ater - for healthier lifest yle and environ[...]

69 TECHNICAL INFORMA TION One S tar Low Emission T wo S tars V ery Low Emission Three S tars Ultra Low Emission Four S tars Super Ultra Low Emission The one-star label identifies engines that meet the Air Resources Board’ s Personal W atercraft and Outboard marine engine 2001 exhaust emission standards. Engines meeting these stan dards h ave 75% [...]

70 TECHNICAL INFORMA TION Specifications Tu n e u p MODEL BF2.3D Description code BA V J T ype SCH LCH Overall length 16.1 in ( 410 mm) Overal l width 1 1.2 in (28 5 mm) Overall height 38.0 in (964 mm) 44.0 in (1,1 17 mm) Tr an s om he i gh t (when transom angle at 5° ) 16.5 in (418 mm) 22.5 in (571 mm) Dry mass [wei ght]* 30.0 lbs (13. 6 kg) 31.5[...]

71 CONSUMER INFORMA TION Honda Publications (United S tates, Puerto Rico, and U.S. V irgin Islands) These publications will give you additional informati on for maintaining and repairing your outboard motor . Shop Manual This manual covers complete m aintenance and overhaul procedures. It is intended to be used by a skilled technici an. A vailable [...]

72 CONSUMER INFORMA TION Please include the following information in yo ur communication: • Y our name, addre ss and telephone number (c omplete with area code) • Model and complete serial number • Date of p urchase • Name and location of selling dealer • Name and location of servicing dealer (if dif ferent) • A detailed description of [...]

73 CONSUMER INFORMA TION W arranty Service Please remember that recommended maintenance interval servicing is not included in your warran ty coverage. Additionally , your warranty does not apply to the normal wear of items (such as spark plug(s), water pump, etc.). As the owner of a Honda pro duct, y our servicing dealer may ask you to authorize an[...]

74 CONSUMER INFORMA TION W arranty S tatements The American Honda Distributor ’ s Limite d W a rranty applies to outboards purchased in the United States, Puerto Rico, or the U.S. V irgin Islands. The Honda Canada Distributor ’ s W arran ty applies to outboards purchased in Canada. The product warranty is only valid in th e country where the pr[...]

75 CONSUMER INFORMA TION T o Qualify for This W arranty: The Honda Outboard Motor must be purchased from Ame rican Honda or a de aler authorized by American Honda to sell Honda Outboa rd Motors in the United States, Puerto Rico, or the U.S. V irgin Islands. This limited warranty applies to the first retail purchaser and each subsequent owner during[...]

76 CONSUMER INFORMA TION Exclusions: This warranty does not ex tend to the following: • Conditions caused by lack of routine maintenance or improper storage (as outlined in the Owner ’ s Manual) • Conditions caused by the use of propeller (s) that do not allow the outboard motor to run in its recommended full throttle rpm range • Operation [...]

77 CONSUMER INFORMA TION T o Qualify for This W arranty: 1. The accessories or replacement parts must be purchased from American Honda or a dealer , distributor , or distributor ’ s dealer authorized by American Honda to sell th ose products in the United S tates, Puerto Rico, and the U.S. V irgin Islands. Parts and Accessories must be purchas ed[...]

78 CONSUMER INFORMA TION T o Obtain W arranty Service: Y ou must, at your ex pense, take the Honda Outboard Motor produc t accessory or replacement part or the outboard motor or bo at on which the accessory or replacement part is installed, and proo f of purchase to any Honda Marine auth orized service f acility or dealer in the United States, Puer[...]

79 CONSUMER INFORMA TION Emission Control System W arranty Y our new Honda outbo ard engine complies with both the U.S. EP A and State of California emissi on regulations. American Hond a provides the sam e emission warranty coverage for outboard engines sold in all 50 states. In all areas of the United States your outboard engine must be designed,[...]

80 CONSUMER INFORMA TION OWNER’S W ARRANTY RESPONSIBILITIES: As the outboard engine owner , you are responsible for the performance of the required maintenance listed in your owner ’ s manual. American Honda Motor Co., Inc. recommends that you retain all receipts covering maintenance on your outboa rd engine, but American Honda Motor Co., Inc. [...]

81 CONSUMER INFORMA TION T O OBT AIN W ARRANTY SER V ICE: Y ou must take your Ho nda outboard engine, alon g with your sales registration card or other pro of of original purchase date, at your expense, to any Honda Marine dealer that is authorized by American Honda Motor Co., Inc. to sell an d service that Honda marine product during its normal bu[...]

82 CONSUMER INFORMA TION EMISSION CONTROL SYSTEM W ARRANTY P AR TS: SYSTEMS COVERED BY THIS W ARRANTY : P AR TS DESCRIPTION: Fuel Metering Carburetor assembly , Throttle body , Fuel injector , Fuel pump, Fuel pressure regulator , Throttle position sensor , Intake air temperature sensor , Engine temperature sensor , Manifold absolute pressu re senso[...]

83 CONSUMER INFORMA TION Canada Distributor’s W arranty HONDA CANADA INC., for and on behalf of Honda Motor Co. Ltd., T okyo, Japan, gives the following written warranty on each new mari ne product manufactured by Honda Motor Co. Ltd., Japan, distributed in Cana da by Honda Canada Inc. and so ld by authoriz ed Honda Marine dealers. Whenever used [...]

84 CONSUMER INFORMA TION THIS W ARRANTY DOES NOT COVER a) Any repairs required as a re sult of collision, accident, striking any object, misuse or lack of required maintenance; b) Any repairs required as a result of any attachments, parts o r devices installed by or rep airs done by a party other than an authorized Honda dealer; c) Any outboard tha[...]

85 CONSUMER INFORMA TION REPLACEMENT P ARTS AND ACCESSOR Y W A RRANTY New genuine Honda replacement parts or accessories sold to a consumer or installed by an authorized Honda Ma rine dealer which are not covered by the DISTRIBUTORS W ARRANTY are wa rranted for a pe riod of one year from date of purchase, provided, however , that this Replaceme nt [...]

86 INDEX Anode ...................... ...................... ....................... ......... 18 Replacement ..................... ....................... .................. 51 ARE YOU READY TO GET UNDER W A Y? ............... 22 A TT ACHMENT ................... ....................... .................. 20 BEFORE OPERA TION ......................[...]

87 INDEX IMPOR T ANT SAFETY INFORMA TION ...................... 6 INFREQUENT OR OCCASIONAL USE .................... 25 INST ALLA TION ....................... ...................... .............. 19 INST ALLA TION POSITION .......................... .............. 19 IS YOUR OUTBOARD MOTOR READY TO GO? .................. ...................... ....[...]

88 INDEX T AKING CARE OF UNEXPECTED PROBLEMS ..... 58 TECHNICAL INFORMA TION .................. .................. 64 THE IMPOR T ANCE OF MAINTENANCE ................ 37 Throttle Grip ..................... ........................... .................. 14 Throttle Grip Friction Kn ob ...... ...................... .............. 14 THROTTLE OPERA TI[...]

00X31-ZW6-6300 BF2.3D Cover1-4 PANTONE 288CVC DIC F101 Black 31ZW663  00X31-ZW6-63  0 K2 N 2eY1 1000.201  .10 Printed in China Includes US and Canadian Models BF2.3D 00X31-ZW6-6300_BF2.3D_Cover(AH).1 1 00X31-ZW6-6300_BF2.3D_Cover(AH).1 1 2011/09/17 18:28:18 2011/09/17 18:28:18[...]