English dropdown-ico

HP (Hewlett-Packard) 288048 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of HP (Hewlett-Packard) 288048, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of HP (Hewlett-Packard) 288048 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of HP (Hewlett-Packard) 288048. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of HP (Hewlett-Packard) 288048 should contain:
- informations concerning technical data of HP (Hewlett-Packard) 288048
- name of the manufacturer and a year of construction of the HP (Hewlett-Packard) 288048 item
- rules of operation, control and maintenance of the HP (Hewlett-Packard) 288048 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of HP (Hewlett-Packard) 288048 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of HP (Hewlett-Packard) 288048, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the HP (Hewlett-Packard) service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of HP (Hewlett-Packard) 288048.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the HP (Hewlett-Packard) 288048 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    311053C Instr uctions - P ar ts A utomatic Airless Spra y Guns P ar t No. 288048 For airless spraying of paints and coatings. P ar t No. 288554 For sealant stre aming applications. 4000 psi (28 MP a, 280 bar) Maximum W orking Fluid Pressure Mounting manif olds must be ordered sep arately . Ref er to Pa r ts section. Important Safety Instru ctions R[...]

  • Page 2

    Related Manua ls 2 311053C Contents Related M anuals . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 W arnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 V entilate Spray Booth . . . . . . . . . . . . . . . . . . . . . 5 Configure G un an[...]

  • Page 3

    Warnings 311053C 3 Wa r n i n g s The f ollowing warnings are f or the setup , use, g rounding, maintenance, and repair of this equipment. Th e e xclama- tion point symbol ale r ts you to a ge neral w ar ning and the hazard symbol ref ers to procedu re-specific risk. Ref er back to these wa rnings. Additional, pr oduct- specific w ar nings may be f[...]

  • Page 4

    Warnings 4 311053C PRESSURIZED EQUIPMENT HAZARD Fluid from the gun/dispense v alve , leaks, or ruptured components can spla sh in the e yes or on skin and cause serious injury . • F ollow Pressure Re lief Procedure in this manual, w hen you stop spra ying an d before cleaning, chec king, or servicing equipment. • Tighten all fluid connect ions [...]

  • Page 5

    Installation 311053C 5 Installation V entilate Spra y Booth Configure Gun and Manif old (Order manif old separately . See Accessories , page 26.) Manif olds 241161 and 241162 The gun is supplied with an int ernal fluid plug (4). See F IG . 1. T o use the gun in a circula ting system, rem ov e the internal plug. In a non-circulatin g system, lea ve [...]

  • Page 6

    Installation 6 311053C Install Air Fittings 1. Install 1/4 in. tube fit ting into the cylinder (CYL) air por t. 2. Install plugs into the atomizatio n (A TOM) air port and the f an (F AN) air por t. Gr ound System The f ollowing grounding instructions are minim um requireme nts f o r a system. Y our system may include other equipment or objects tha[...]

  • Page 7

    Installation 311053C 7 Mount Gun Reciprocating Arm Rod Mount Manif olds 241161 and 241162 T o mount the gun on a reciprocating ar m rod [0.5 in. (13 mm) diameter maxim um]: 1. Inser t the mounti ng bar (A) throug h the hole in the manif old as shown in F IG . 3. 2. Secure the gun to t he bar b y tightening the mount- ing screw (B). 3. Ensure th e t[...]

  • Page 8

    Setup 8 311053C Setup Air Line and Accessory Recommendations 1. Install an air pressure r egulator on th e gun cylinde r air supply line. A minimum of 70 psi (0.4 9 MPa, 4.9 bar) air pres- sure must be supp lied to the cylinder f or proper operat ion. Air pressure opens the v alve , a spr ing closes the v a lv e. A three-wa y air valv e, which e xh[...]

  • Page 9

    Setup 311053C 9 Manif olds 288219 and 288220 6. In a circulating system , connect an electr ically con- ductiv e fluid hose to the gun fluid outlet (G) . In a non-circulat ing system , remov e the gu n fluid outlet fitt ing (G) and plug the outlet port with the pipe plug (109 ) supplied. Manif old 244930 7. This manif old is equipped with passages [...]

  • Page 10

    Setup 10 311053C Flush Spra y Gun Bef ore r unning an y paint throug h the spra y gun: 1. Flush the gun with a solv ent that is compatib le with the fluid to be spr ay ed, using the lowest possib le fluid pressure and g rounded metal container . 2. P erfor m Pressure Relief Procedure ; see page 11. Install Spra y Tip 1. P erfor m Pressure Relief Pr[...]

  • Page 11

    Operation 311053C 11 Operation Pressure Relief Pr ocedure 1. Shut off the po wer to the pump . 2. T urn off the air and fluid supply to the gun. 3. Close the b leed-type master ai r v alve (required in the system). 4. T r igger the gun into a g rounded metal waste con - tainer to reliev e the fluid pre ssure. 5. Open the pump dr ain valv e (require[...]

  • Page 12

    Daily Gun Care 12 311053C Dail y Gun Care CA UTION Meth ylene chloride with formic or propionic acid is not recommended as a flushing or cleaning solv ent with this gun as it will damage aluminum and nylon compo- nents . CAUTION Solv ent left in gun air passage s could result in a poor quality pain t finish. Do not use an y cleaning method which ma[...]

  • Page 13

    Daily Gun Care 311053C 13 General System Maintenance •P e r f o r m Pressure Relief Pr ocedure , page 11. • Clean the fluid and air line f ilters daily . • Chec k for an y fluid leakage from the gun and fl uid hoses. Tighten fitting s or replace equipment as needed. • Flush the gun bef ore changing colors and whene ve r yo u are done oper a[...]

  • Page 14

    Troubleshooting 14 311053C T r oubleshooting General T roub leshooting Check all possib le remedies in the troubleshooting char ts bef ore disassembling the gu n. Some improper patte r ns are caused by the improper balance be tween air and fluid. Ref er to Spray Pattern T roub leshooting , page 16 . Prob lem Cause Solution Fluid leakage through v e[...]

  • Page 15

    Troubleshooting 311053C 15 Fluid needle will not trigger Loose or missing fluid needle stop (17) or setscrew (16). Brok en fluid needle (1 2). Air leaking around piston (21). Swollen piston o-ring (22). Insufficient air pressure on the trig - ger . Spra y tip (9) is plugged. Plug (4) is in the incorrect fl uid por t. Replace stop (17) or tighten se[...]

  • Page 16

    Troubleshooting 16 311053C Spra y Pa ttern T roub leshooting Prob lem Cause Solution Flutter ing spra y . Insufficient fluid su pply . Air in paint supply line. Adjust fluid regulator or fill fluid sup- ply tank. Chec k, tighten siphon hose connec- tions , b leed air from pa int line. Spitting spr ay . W or n seat (10, 41) or needle (12) ball. Dir [...]

  • Page 17

    Service 311053C 17 Service Disassembl y 1. Follo w Pressure Relief Pr ocedure , page 11. 2. Unscrew the four scre ws (14) and remove the gun from the ma nif o ld. 3. Unscrew the tip retainer nut (7). Re mov e the spra y tip (9) and ga ske t (8). See Figs. 8 and 9. 4. Remov e the cap (18) from th e piston housing (1). Remov e the springs (20 and 19)[...]

  • Page 18

    Service 18 311053C F IG . 13 SERVICE NOTES: Seat gasket (11) must be replaced if seat (10) is removed or replaced to avoid fluid leakage Lubricate threads with anti-seize lub ricant Lubricate with light-weight oil Do not lubricate Torque to 20-25 ft-lb (27-34 N•m) Apply semi-permanent anaerobic sealant Torque to 4-5 in-lb (0.45-0.56 N•m) Tighte[...]

  • Page 19

    Service 311053C 19 Reassembl y 1. P erf or m the f ollowing applicable ste p: • Non-circulating P a int Guns: Lubricate the backup (6) and o-r ing (5) and in stall them on th e fluid outlet port plug (4). Install the plug in the fluid outlet por t of the f luid housing (2) . See F IG . 13. Reinstall the gasket (3). • Circulating P aint Guns: Re[...]

  • Page 20

    Parts 20 311053C Pa r t s Model 288048 F IG . 14 SERVICE NOTES: Seat gasket (11) must be replaced if seat (10) is removed or replaced to avoid fluid leakage Lubricate threads with anti-sei ze lubricant Lubricate with light-weight oil Do not lubricate Torque to 20-25 ft-lb (27-34 N•m) Apply semi-permanent an aerobic sealant Torque to 4-5 in-lb (0.[...]

  • Page 21

    Parts 311053C 21 Model 288554 F IG . 15 SERVICE NOTES: Seat gasket (11) must be replaced if seat (10) is removed or replaced to avoid fluid leakage Lubricate threads with anti-sei ze lubricant Lubricate with light-weight oil Do not lubricate Torque to 20-25 ft-lb (27-34 N•m) Apply semi-permanent an aerobic sealant Torque to 4-5 in-lb (0.45-0.56 N[...]

  • Page 22

    Parts 22 311053C Pa r t s * P ar ts included in Air Seal Repair Kit 288171 (pur - chase separately). Th e kit includes some pa r ts that are not used on this gun . † P ar ts included in Fluid Seal Repair Kit 239896 (p ur- chase separately). ★ An e xtra gasket (3) is included as a spare. ✓ K eep these spare parts on hand to reduce do wn time. [...]

  • Page 23

    Parts 311053C 23 P ar t No. 241161 Nor th America Manifold P ar t No. 241162 International Manif old ❖ P ar t No. 241161 only . ◆ P ar t No. 24 1162 only . P ar t No. 244930 High Flow Ambient or T emperat ure Conditioned Man i- f old for streaming or spra ying. Ref. No. P art N o. Description Qty . 101 192441 MANIFOLD , side fluid por ts 1 103 [...]

  • Page 24

    GG0 Series Tip Selection Charts 24 311053C GG0 Series Tip Selection Char ts GG0 Series Spra y Tips Orifice Size in. (mm) * Fluid Output oz/min (lpm) at 600 psi (4.1 MP a, 41 bar) Maximum P attern Width at 12 in. (300 mm) 2 to 2.5 (50) 4 to 4.5 (100) 6 to 6.5 (150) 8 to 8.5 (200) 10 to 10.5 (250) 12 to 13 (300) 14 to 15 (350) 16 to 17 (400) 18 to 19[...]

  • Page 25

    Sealer Application Tip an d Air Cap Selection Charts 311053C 25 Sealer Application Tip and Air Cap Selection Char ts Shower Tip Streaming Tips Single Orifice F an Pattern Spra y Tips No. of Orifices Orifice Size in. (mm) Pa r t . N o . 6 0.021 (0.533 ) C08224 Orifice Size in. (mm) Pa r t . N o . Orifice Siz e in. (mm) Par t . N o. 0.025 (0.635 ) 27[...]

  • Page 26

    Accessories 26 311053C Accessories Gun Manif olds Order separa tely; not included with gun. (See Par t s , page 22.) P ar t No. 241161 Nor th America Manif old P ar t No. 241162 International Manif old P ar t No. 244930 High Flow Ambie nt or T emperature Conditioned Man i- f old for str eaming or spra ying. Grounding Clamp and Wire 222011 High Pres[...]

  • Page 27

    Dimensions 311053C 27 Dimensions F IG . 19 TI8113a TI8114a 2.0 in. (50.8 mm) 3.86 in. (98 .0 mm) 5.23 in. (139. 7 mm) 3.0 in. (76.2 mm) 1.375 in. (34.9 mm) 2.0 in. (50.8 mm) 2.245 in. (57.02 mm) 0.5 in. (12.7 mm)[...]

  • Page 28

    Mounting Hole Layout 28 311053C Mounting Hole La y out F IG . 20: Manif old Mounting Hole Lay out 0.4 in. Two M5 x 0.8 x 0.25 in. 0.805 in. ( 20.5 mm) 0.187 in. (4 .8 mm) 1.375 in. (35 mm) Two 0.128 dia meter x 0.31 in. (7. 8 mm) deep 2.125 in. (54 mm) holes (for a lignment pin ) Remove set screws when using bottom mounting patt ern. (6.3 mm) holes[...]

  • Page 29

    Technical Data 311053C 29 Te c h n i c a l D a t a T rigg ering Speed These v alues apply to a new gun with a 6 ft (1.8 m), 1/4 in. (6. 3 mm) OD cylinder air line and a 0.019 in. tip . These v alues will vary slightly with use and with v ar iations in equipment. Sound Pressure Levels (dBa) Sound pressure me asured 3.28 ft (1 m) from equipment. Soun[...]

  • Page 30

    All written and visual data contained in this document reflects the latest product information available at the time of publica tion. Graco reserves the right to make changes a t any time without notice. This manual contains English. MM 311053 Graco Headquarters: Minneapolis International Offices: Belgium, China, Japan, Korea GRACO INC. P.O. BOX 14[...]