Go to page of
Similar user manuals
-
Printer
HP Photosmart D7200 Series
169 pages 7.13 mb -
Printer
HP DeskJet Portable
202 pages 1.71 mb -
Printer
HP Color LaserJet Pro MFP M177
122 pages 4.55 mb -
Printer
HP LaserJet Pro MFP M228
214 pages 3.32 mb -
Printer
HP 9050
218 pages 3.37 mb -
Printer
HP PageWide Enterprise Color MFP 586 serie
252 pages 4.95 mb -
Printer
HP LaserJet 4050 T
260 pages -
Printer
HP Deskjet 3000
8 pages
A good user manual
The rules should oblige the seller to give the purchaser an operating instrucion of HP 5L (C3941A), along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.
What is an instruction?
The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of HP 5L (C3941A) one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.
Unfortunately, only a few customers devote their time to read an instruction of HP 5L (C3941A). A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.
What should a perfect user manual contain?
First and foremost, an user manual of HP 5L (C3941A) should contain:
- informations concerning technical data of HP 5L (C3941A)
- name of the manufacturer and a year of construction of the HP 5L (C3941A) item
- rules of operation, control and maintenance of the HP 5L (C3941A) item
- safety signs and mark certificates which confirm compatibility with appropriate standards
Why don't we read the manuals?
Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of HP 5L (C3941A) alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of HP 5L (C3941A), and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the HP service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of HP 5L (C3941A).
Why one should read the manuals?
It is mostly in the manuals where we will find the details concerning construction and possibility of the HP 5L (C3941A) item, and its use of respective accessory, as well as information concerning all the functions and facilities.
After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.
Table of contents for the manual
-
Page 1
Service Manual HP LaserJet 5L (C3941A)[...]
-
Page 2
© Copyright He wlett-Packard Company 1995 All Rights Reserv ed. Reproduction, adaptation, or translation without p rior written permission is prohibited, except as allo wed under the copyright la ws. Publication number C3941-90987 First edition, September 1 995 W arranty The information contained in this document is subject to change without notic[...]
-
Page 3
Con ventions This manual uses the following con ventions: Color is used to emphasize items which are important to the material under discussion. The names of major printer parts and assemblies are CAPIT ALIZED. Bold is used for emphasis, particularly in situations where italic type would be confusing. Italic type is used to indicate related documen[...]
-
Page 4
Chapter Descriptions 1 Product Inf ormation Orientation to the printer , as well as the service and repair philosophy , is discussed. Information on obtaining assistance and warranty is also here. 2 Site Requirements Here are recommendations pertaining to installation requirements. 3 Operating Overview This chapter has detailed information about th[...]
-
Page 5
List of Figur es Figure 1-1 HP LaserJet 5L Model and Serial Numbers . . . . . . . . . . . 1-4 Figure 1-2 Front/Side V ie ws of the Printer . . . . . . . . . . . . . . . . . . 1-6 Figure 1-3 Front Door Assemblies . . . . . . . . . . . . . . . . . . . . . . 1-7 Figure 1-4 Back V ie w of the Printer . . . . . . . . . . . . . . . . . . . . . 1-8 Figure[...]
-
Page 6
Figure 6-23 Pickup Roller Assembly Remov al (1 of 2) . . . . . . . . . . . 6-27 Figure 6-24 Pickup Roller Assembly Remov al (2 of 2) . . . . . . . . . . . 6-28 Figure 6-25 Paper Pickup Roller Assembly Replacement (Inside/Front V ie w) 6-29 Figure 6-26 Paper Feed Frame Remo v al . . . . . . . . . . . . . . . . . . . 6-30 Figure 6-27 Paper Feed Frame[...]
-
Page 7
List of T ables T able 1-1 Printer Features . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 T able 1-2 Paper Capacities and Sizes . . . . . . . . . . . . . . . . . . . . 1-3 T able 1-3 Performance Specifications . . . . . . . . . . . . . . . . . . . 1-5 T able 1-4 Electrical Specifications . . . . . . . . . . . . . . . . . . . . . 1-5 T abl[...]
-
Page 8
viii[...]
-
Page 9
1 Pr oduct Inf ormation Contents Printer Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Paper Capacities and Sizes . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 Model and Serial . . . . . . . . . . . . . . . . . . . . . . .[...]
-
Page 10
1-2 Product Information[...]
-
Page 11
Printer F eatur es Paper Capacities and Sizes Features HP LaserJet 5L (C3941A) Print Speed 4 ppm T ext & Gr aphics Resolution 300 or 600 dpi Printer Language Enhanced PCL 5 Monthly Usage (pages) 4,000 pages Memory: Standard 1 Maximum Memory Capacity 1 Mbyte RA M 9 Mbyte total (a v ailable in i ncrements of 1, 2, 4, and 8 Mbytes) 5 V JEDIA card [...]
-
Page 12
Identif ication Model and Serial The model number and serial numbers are listed on identification labels located on the bottom of the printer . The model number is alphanumeric, such as C3941A for the HP LaserJet 5L printer . The serial number contains information about the Country of Origin, the Revision Lev el, the Production Code, and production[...]
-
Page 13
Specif ications Category Specification Print Speed* 4 ppm Monthly Usage (Duty Cy cle) 4,000 pages Lif e Expectancy of T oner Car tridge (pages)** 2,500 pages @ 5% cov erage First Print A4 <23 sec onds Letter <23 seconds * Actual s peed depends on data complexity and software handling efficiency. ** Toner cartri dge life can be extended by us [...]
-
Page 14
Pr oduct Over view Front/Side Views of the Printer 1. P aper Input Suppor t 7. Front P anel Button 13. Front Output S lot (face-up) 2. P aper Output Suppor t 8. P aper Output Bin 3. P aper Guides 9. P aper Path Le v er 4. Error (top) Light 10. Serial and Model Number (under printer) 5. Data (middle) Light 11. P aper Input Bin 6. Ready (bottom) Ligh[...]
-
Page 15
Front Door Assemblies 14. P aper Release Le ver 16. T ransf er Rol ler 15. T oner Car tridge Compar tment 17. EP Door Figure 1-3 Product Information 1-7[...]
-
Page 16
Back View of the Printer 18. P ower Cab le Connector 20. Memor y Expansion Cov er 19. P arallel Cab le Connector Figure 1-4 I 1-8 Product Information[...]
-
Page 17
Service A ppr oach Repair of the printer normally begins with the use of the printer’ s internal diagnostics in conjunction with the troubleshooting procedures in Chapter 7. Once a faulty part is located, repair is generally accomplished by assembly le v el replacement of Field Replaceable Units (FR Us). Some mechanical assemblies may be repaired[...]
-
Page 18
Print Utilities HP provides se veral utilities for enhancing use of the LaserJet printers in MS-DOS and W indows en vironments. More information on specific utilities is included with each of the dri v ers listed in T able 1-6. Description Part Number SMO SME HPD HP LaserJet F amily Quick Reference S er vice Guide 5010-3991 X X HP LaserJet 5L P rin[...]
-
Page 19
T echnical Assistance HP ASAP HP ASAP (Automated Support Access Program) provides free user technical support information 24 hours a day , 7 days a week. The ASAP system includes HP A UDIO-TIPS and HP FIRST , both explained belo w . The ASAP service requires a touchtone phone. HP A UDIO-TIPS HP A UDIO-TIPS is an interactive v oice response system p[...]
-
Page 20
Customer Inf ormation Centers (North America Only) For presales information, contact the nearest He wlett-Packard Customer Information Center , 1-800-752-0900 in North America. Customer Support Center (Assist Line) The HP Customer Support Center , (208-323-2551) is av ailable to answer technical questions regarding setup, conf iguration, installati[...]
-
Page 21
W arranty This warranty gi v es you specif ic le gal rights. Y ou may also have other rights, which may va ry from area to area. He wlett-P ackard warrants the 5L LaserJet printer against defects in materials and workmanship for a period of one year from the date of purchase by the end user and is not transferable. During the warranty period, He wl[...]
-
Page 22
If you are using a mechanical switchbox, ensure that it is equipped with a surge protector . Damage to your printer could occur from the use of unprotected mechanical switchboxes. The warranty period begins either on the date of deli very or , where the purchase price includes installation by He wlett-P ackard, on the date of installation. W arrant[...]
-
Page 23
2 Site Requir ements Contents Site Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Operating En vironment . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Printer Space Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 The HP C3906A T oner Cartridge . . . . . . . . . . . . . . . . . . . . .[...]
-
Page 24
2 -2 Site Requirements[...]
-
Page 25
Site Requir ements Operating En vironment The en vironmental requirements listed in the table below must be maintained to ensure the proper operation of this printer . Consider the following points before installing the printer: • • Install in a well-ventilated, dust-free area. • • Install on a hard, flat and continu ous surface , with all [...]
-
Page 26
Printer Space Requir ements Printer Space Requirements Figure 2-1 Description Dimension Width 13.2 in. (335.5 mm) Depth 12.3 in. (311.2 mm) Height (storage) (operational) 8.9 in. (227.5 mm) 14.6 in. (372.7 mm)* W eight (with toner car tridge) 15.9 lbs. (7.2 kg) T oner car tridge weight** 1.5 lbs. (.7 kg) * With letter i nput assembly extended. ** S[...]
-
Page 27
The HP C3906A T oner Cartridge T oner cartridges contain components that are sensiti ve to light, temperature, and humidity . Follo w the recommendations in this section to ensure the highest quality and longest life of HP toner cartridges. Keep the printer within the follo wing environmental conditions for optimum performance. Storage Conditions T[...]
-
Page 28
T oner Cartridge Handling Suggestions • • Before installing a cartridge, distribute the toner evenly by rotating the cartridge back and forth five to six times. (See Figure 2-2.) Repeat this action when toner begins to run low. Toner Cartridge Distribution • • Do not touch the surface of the photosensitive drum in the cartridge. Protect the[...]
-
Page 29
3 Installation and Conf iguration Contents Unpacking and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 Step 1: Choose the best location . . . . . . . . . . . . . . . . . . . . . . 3-3 Step 2: Unpack the printer . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 Step 3: Check package contents . . . . . . . . . . . . . . .[...]
-
Page 30
3-2 Installation and Configuration[...]
-
Page 31
Unpacking and Installation Before unpacking the printer , inspect the shipping container for signs of physical damage. Since a damaged shipping box is an indication of improper handling during shipping, the printer may also be damaged. Note If the shipping container has any sign of damage, unpack the printer and plug it in with the carrier’ s age[...]
-
Page 32
Step 4: Install the toner cartridge 1 Open the EP Cartridge door . 2 Remov e toner cartridge from its box and cut it open. Sa ve the packing materials for possible cartridge storage. 3 Shake the cartridge vigorously to distrib ute the toner e venly inside the cartridge. (See Figure 2-2.) 4 Grasp the toner sealing tab on the right side of the cartri[...]
-
Page 33
Note If your system does not meet these minimum requirements, only the PCL dri v er software will be installed. Minimum System Requirements • • 486 or above PC with 8 Mbytes DRAM (minimum) • • Fully functional bi-directional cable (IEEE 1284-compliant cable recommended) • • HP LaserJet 5L printer connected and powered on To install the [...]
-
Page 34
If you would like to connect another de vice to the LPT port you have conf igured to use with the HP LaserJet 5L, select the other device from the Microsoft W indows Control Panel and restart windo ws. The HP LaserJet printer is capable of receiving and processing both PCL commands and host-based generated data. Host-Based Printer Settings T o sele[...]
-
Page 35
Host-Based Printing Status T o vie w your printer’ s status, open the HP LaserJet 5L Printer group within Program Manager and select Status W indow . As sho wn in Figure 3-2 belo w , the status window reports your printer’ s current status. In this case, the printer is Ready . Host-Based Printing Status This host-based status window is only com[...]
-
Page 36
PCL Printer Settings T o change printer settings, select Contr ol P anel , Printers , HP LaserJet 5L (PCL) , Setup . The printer settings window will appear . (See Figure 3-3.) Select from the following options: • • Paper —Select Paper Size, Paper Source (manual feed), Copies, Orientation (portrait or landscape), and Set Custom Paper Size. ?[...]
-
Page 37
PCL Printing Status T o vie w your printer’ s status, open the HP LaserJet 5L PCL Printer group within Program Manager and select Status W indow . As sho wn in Figure 3-4 belo w , the status window reports your printer’ s current status. In this case, the printer is Ready . PCL Printing Status As with the host-based software, the PCL software h[...]
-
Page 38
Using the Contr ol Panel Control P anel Lay out The Control Panel consists of three status lights and a Front Panel Button located at the front of the printer . The Control Panel consists of one button and three status lights. ERR OR (Y ellow) DA T A (Green) READ Y (Green) These lights can be in only one of the following states: OFF ON Blinking 3-1[...]
-
Page 39
LED Lights The LED lights provide a quick w ay to check the printer’ s status. When this Indicator: Looks like this: It means this: Do this: On Blinking Ready Ready to print. Print job in progress . Let job finish printing. On Form Feed There is unprinted data in the buff er. Briefly press the F ront P anel Button to print the remaining data. Bli[...]
-
Page 40
When this indicator: Looks like this: It means this: Do this: Blinking Error (light b linking) P age T oo Comple x The page may be too c omplex for the printer’ s memor y capacity or the printer may not be ab le to create the image f ast enough to keep pac e with the engine printing process . Briefly press and release the F ront P anel Button to [...]
-
Page 41
The Front P anel Button Depending on what state the printer is in, pressing the Front Panel Button allo ws you to control printing tasks by either starting or resuming a printer function. Use the Front Panel Button to accomplish the follo wing tasks: Function Action Lights Result W ake Up Briefly push and release the button. All l ights are off whi[...]
-
Page 42
Printing a Self-T est Page A self-test page can be useful in troubleshooting printer problems and determining which fonts hav e been do wnloaded to the printer . Self-test Page The self-test page includes an internal font listing showing all 26 pro vided fonts (1) and a listing of the current printer configuration (2). (If an y fonts ha ve been dow[...]
-
Page 43
Continuous Self T est A continuous self test can be useful for troubleshooting paper path and other problems. T o print a continuous self test: 1 Disconnect the printer from the power source. 2 Press and hold down the Front P anel Button while connecting power . 3 Continue holding the button for about f iv e seconds. All lights will illuminate at o[...]
-
Page 44
Printing an Engine T est The engine test print can be used to verify that the print engine is functioning correctly . The Formatter PCA is completely bypassed during an engine test. Consequently , this test is useful for isolating engine printer problems. The engine test prints a full page of vertical lines do wn the entire printable area. This pag[...]
-
Page 45
Resetting the Printer Resetting the printer accomplishes the following: • • Clears all data from the printer’s memory (including unprinted data, downloaded fonts, and macros). • • Stops any printing that is taking place and ejects the page. • • Removes some error conditions. • • Resets the printer to its factory default settings. [...]
-
Page 46
3-18 Installation and Configuration[...]
-
Page 47
4 Printer Maintenance Contents Life Expectancy of Consumables . . . . . . . . . . . . . . . . . . . . . . . 4-3 T oner Cartridge Life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4 Saving T oner with EconoMode . . . . . . . . . . . . . . . . . . . . . . 4-4 Refilled T oner Cartridges . . . . . . . . . . . . . . . . . . . . . . . . [...]
-
Page 48
4-2 Printer Maintenance[...]
-
Page 49
Life Expectancy of Consumables Alw ays inspect the components listed in T able 4-1 for wear when servicing the printer . Replace these components as needed, based on printer failures or wear , not strictly on usage. Description Par t No. Est Life (pgs) Remarks T oner Car tr idge (user replaceab le) C3906A 2,500* When print becomes f aint, shake c a[...]
-
Page 50
T oner Cartridge Life The toner cartridge has been designed to simplify the replacement of the printer’ s major “consumable” parts. The toner cartridge contains the printing mechanism and a supply of toner . When using a typical word-processing application, a toner cartridge will print approximately 2500 pages where the text cov ers about 5% [...]
-
Page 51
proofs. EconoMode can be set through your printer dri v er . See Chapter 3 for information. Notes Some software applications may refer to this as “draft mode." Ref illed T oner Cartridges While He wlett-P ackard does not prohibit the use of refilled toner cartridges during the warranty period or while under a maintenance contract, we do not [...]
-
Page 52
Cleaning the Printer T o maintain the print quality, thoroughly clean the printer: • • Every time you change the toner cartridge. • • After printing approximately 2,500 pages. • • Whenever print quality problems occur. Clean the outside of the printer with a lightly water -dampened cloth. Clean the inside with only a dry , lint-free clo[...]
-
Page 53
Cleaning Printer Components CAUTION T o a void permanent damage to the toner cartridge, do not use ammonia-based cleaners on or around the printer . Do not touch the transfer roller with your fingers. Contaminants on the roller can cause print quality problems. COMPONENT CLEANING METHOD/NOTES Outside Cov ers Use a water-dampened cl oth. Do not use [...]
-
Page 54
Static Eliminator Teeth (located in front of the transfer roller) Cleaning Spilled T oner Defecti v e toner cartridges can dev elop leaks. In addition, after a paper jam has occurred, there may be some toner remaining on the rollers and guides inside the printer . The pages that print immediately after the jam may pick up this toner . Clean spilled[...]
-
Page 55
5 Functional Over view Contents Basic Printer Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 DC Controller/Po wer System . . . . . . . . . . . . . . . . . . . . . . . . . 5-4 Print Engine Control System . . . . . . . . . . . . . . . . . . . . . . . . 5-5 Po wer System (on DC Controller PCA) . . . . . . . . . . . . . . . . .[...]
-
Page 56
5 - 2 Functional Overvie w[...]
-
Page 57
Basic Printer Functions This chapter presents a generalized functional overvie w of the printer and the printing processes. The following printer systems are discussed: • • DC Controller System/ Power System • • Formatter System • • Image Formation System • • Paper Feed System • • Laser/Scanner Sy stem Figure 5-1 is a generalize[...]
-
Page 58
DC Controller/P ower System The DC Controller PCA coordinates all print engine activities, dri ves the laser , and coordinates print data from the Formatter PCA with the image formation process. The DC Controller also includes both A C and dc po wer supply and distribution circuitry . The DC Controller controls the following systems and functions: [...]
-
Page 59
Print Engine Control System Laser and Scanner Drive Based on information recei v ed from the Formatter , the DC Controller sends signals to the Laser/Scanner Assembly to modulate the laser diode ON and OFF and to dri ve the Laser/Scanner motor . Refer to “Image Formation System, ” later in this chapter for more information. Paper Motion Monitor[...]
-
Page 60
P ower System (on DC Contr oller PCA) The A C, dc, and high voltage po wer supply circuits are all contained within the DC Controller PCA. AC Power Distribution The A C po wer circuitry supplies A C v oltage whene ver the po wer cord is connected to the A C po wer source. A C voltage is distrib uted to the dc po wer supply circuitry and to the A C [...]
-
Page 61
• • A job is received. • • The Front Panel Button is pressed. • • The printer front door is opened. Note The printer will not enter SleepMode if there is a printer error . High Voltage Power Distribution The High V oltage Power Supply PCA applies an o v erlap of dc and A C voltage to the primary charging roller and the de veloping rolle[...]
-
Page 62
F ormatter System The Formatter PCA is responsible for the follo wing: • • Receiving and processing print data from the printer interface. • • Monitoring Front Panel Button and relaying printer status information. • • Developing and coordinating data placement and timing with the print engine. • • Storing font information. • • C[...]
-
Page 63
Control P anel Status LED Lights The Formatter uses three LEDs mounted under the printer cov er to communicate printer status to the user . Refer to “Using the Control Panel” in Chapter 3 and “Printer Error T roubleshooting” in Chapter 7 for more information on the lights. Front Panel Button The Formatter PCA is connected to a microswitch l[...]
-
Page 64
EconoMode The EconoMode setting uses approximately 50% less toner than standard mode printing by reducing the dot density . Ho we ver , EconoMode does not extend toner cartridge component life. EconoMode, which can also be thought of as “draft mode, ” is user-selectable through some softw are applications. The default setting is Off. EconoMode [...]
-
Page 65
Enhanced I/O The Enhanced I/O feature allows printer memory to be used for storing data recei v ed from the host computer . When Enhanced I/O is enabled, you can send more data to your printer in shorter amounts of time, which allows you to return to your application sooner . Enhanced I/O has the following options: • • Auto —allows the printe[...]
-
Page 66
Image F ormation System Laser printing requires the interaction of sev eral different technologies (such as electronics, optics, and electrophotographics) to provide a printed page. Each process functions independently and must be coordinated with the other printer processes. Image formation consists of six processes: • • Step 1. Drum Cleaning [...]
-
Page 67
T oner Cartridge As the “heart” of the Image Formation System, the toner cartridge houses the cleaning, conditioning, and dev eloping steps of the process. The toner cartridge contains the photosensitiv e drum, primary charging roller , developing station, toner cavity , and cleaning station. Including these components, which wear , degrade, or[...]
-
Page 68
Step 4: Image Dev eloping At this stage of the process, the latent electrostatic image is present on the drum. The toner particles obtain a negati ve surface char ge by rubbing against the dev eloping cylinder which is connected to a negati ve dc supply . The negativ ely charged toner is attracted to the dischar ged (exposed, grounded) areas of the[...]
-
Page 69
Paper F eed S ystem Both the Paper Input Bin and the Single Sheet Input Slot mer ge into one, main input area. Paper placed in either of these areas enables the Paper Out Sensor (sensor 202), which informs the DC Controller that paper is present. When the printer receiv es a print job and is ready to print, the DC Controller enables the Laser/Scann[...]
-
Page 70
Figure 5-5 shows a simplif ied paper path and the locations of the photosensors and rollers. Simplified Paper Path Figure 5-5 5 - 16 Functional Overvie w[...]
-
Page 71
Figure 5-6 shows the locations of the photosensors, switches, solenoid, and other important printer elements. T able 5-1 describes the function of each photosensor and the solenoid. Solenoid and Sensors Figure 5-6 No. Name Description SL1 P aper Pic k-up Solenoid Enables the P aper Pic kup Roller . PS201 P aper Exit Sensor Senses when paper has s u[...]
-
Page 72
Paper J am Detection The Paper Out Sensor (PS202), Paper Re gistration Sensor (PS203), and the Paper Exit Sensor (PS201) detect when paper is moving through the printer . (See Figure 5-5 for roller and sensor locations.) If a paper jam is detected, the DC Controller immediately stops the printing process and causes a paper jam indication on the fro[...]
-
Page 73
Basic Sequence of Operation The Formatter PCA and the DC Controller PCA share information during printer operation. The DC Controller-to-Formatter Connector (J201) forms a link which operates as a serial data bus. This allo ws printer status, command information, and dot-image data to be passed between the two PCAs. Figure 5-7 sho ws the general ti[...]
-
Page 74
General Timing Diagram Figure 5-7 5 - 20 Functional Overvie w[...]
-
Page 75
6 Remov al and Replacement Contents Remov al and Replacement Strategy . . . . . . . . . . . . . . . . . . . . . . 6-3 Required T ools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4 Installing Memory Cards (DRAM) . . . . . . . . . . . . . . . . . . . . . . 6-5 Covers and Doors . . . . . . . . . . . . . . . . . . . . . . . . . [...]
-
Page 76
6 - 2 Removal and Replacement[...]
-
Page 77
Remov al and Replacement Strategy This chapter documents remov al and replacement of Field Replaceable Units (FR Us) only . Exchange assemblies should be sent to SMO for repair . Replacement is generally the re v erse of remov al. Occasionally , notes are included to provide direction for dif ficult or critical replacement procedures. WARNING! Unpl[...]
-
Page 78
Requir ed T ools • • #2 Phillips Screwdriver • • 5.5 mm Hexhead Screwdriver • • Small Flathead Screwdri ver • • Needlenose Pliers. Caution A Posidri v scre wdriver will damage the printer’ s scre w heads. Use Phillips only . Figure 6-1 shows the dif ference between a Phillips and a Posidri v screwdri ver . Note that a Phillips tip[...]
-
Page 79
Installing Memory Cards (DRAM) 1 Unplug the power cord from the printer. You should not install a memory card while the printer is in SleepMode. 2 Open the Printer Door, remove the toner cartridge, and close the Printer Door. Protect the toner cartridge from light while you are working on the printer. 3 Remove any paper in the paper tray. Gently ti[...]
-
Page 80
Cov ers and Doors Back Cov er 1 Unplug the power cord and remo ve the parallel cable from the back of the printer . 2 Remove the toner cartridge. 3 Lift the Input Extender assembly . Caution Y ou must lift the Input Extender when the covers are remo ved or it will break. 4 Remove the (3) scre ws (Figure 6-2, callout 1). Back Cover Removal (1 of 2) [...]
-
Page 81
5 Separate the rear panel from the main cover , pulling the lower corners a way from the printer first, then using a flathead scre wdri ver to pry the two upper corners apart (Figure 6-3, callout 1). 6 T o remo v e the cover , pull it downw ard (Figure 6-3, callout 2). Back Cover Removal (2 of 2) To reinstall Make certain the Input Extender is up. [...]
-
Page 82
EP Door Assembly 1 Unplug the power cord and remo ve the parallel cable from the back of the printer . 2 Open the EP door . 3 Remove the toner cartridge. 4 Along the door hinge, there is a flex point. Press the left tab inward to release it. The right tab will fall out easily (Figure 6-4). EP Door Assembly Removal Figure 6-4 6 - 8 Removal and Repla[...]
-
Page 83
Memory Door 1 Unplug the power cord and remo ve the parallel cable from the back of the printer . 2 Remove the toner cartridge. 3 Gently tip the printer onto its side so that the Control Panel is on top. 4 Carefully pull the door tab out (Figure 6-5, callout 1) and away from the printer in a gentle rocking motion (Figure 6-5, callout 2). Memory Doo[...]
-
Page 84
Main Cov er and Paper Input Assembly 1 Remove the toner cartridge. 2 Remov e memory door . Caution Remov e the memory door f irst. The door will break if you remove the Main Co ver without removing the memory door . 3 Remove the EP Door Assembly . 4 Remove the Back Co v er . 5 Remove the (2) scre ws from the top of the printer (Figure 6-6, callout [...]
-
Page 85
Inter nal Assemblies Control P anel 1 Remove the Printer Co v ers. 2 Release the Control Panel connector (Figure 6-7, callout 1). 3 Press the tab on the top of the Control Panel do wnward (Figure 6-7, callout 2). The Control Panel will pop out of the printer chassis. 4 Lift the Control Panel out. Control Panel Removal Figure 6-7 Remov al and Replac[...]
-
Page 86
Exit Roller Assembly 1 Remove Printer Co v ers. 2 Grasp the tabs at the lower ends of the Exit Roller b ushings and pull inward. This will release the tabs from the printer chassis (Figure 6-8, callout 1). 3 Rotate the tabs 90 degrees, clear of the printer chassis (Figure 6-8, callout 2). 4 Lift the roller out. Exit Roller Removal Figure 6-8 6 - 12[...]
-
Page 87
Deliv ery Assembly 1 Remove the Printer Co v ers and Exit Roller Assembly . 2 Remove the EP Right-Hand assembly by pressing the tab in (Figure 6-9, callout 1) and sliding the assembly tow ard the front of the printer (Figure 6-9, callout 2). Note The EP Right-Hand assembly must be removed to access any fuser components. Delivery Assembly Removal (1[...]
-
Page 88
3 Remove the (2) scre ws (Figure 6-10, callout 1). Once the screws hav e been removed, rotate the rear of the assembly up and lift it out of the printer . Delivery Assembly Removal (2 of 2) Caution Upon replacement, make certain that the positioning pins on the bottom of the assembly are properly positioned before tightening the screws. Note The ta[...]
-
Page 89
Fuser Pressur e Plate 1 Remove Printer Co v ers and Deli very Assembly (Figures 6-9 and 6-10). 2 Remove the (2) scre ws (Figure 6-11, callout 1). 3 Press the Fuser Plate retainer clips out to release the Pressure Plate (Figure 6-11, callout 2). 4 Rotate the plate around and lift up to remove it (Figure 6-11, callout 3). Fuser Pressure Plate Removal[...]
-
Page 90
To reinstall: The Fuser Pressure Plate is kept in place by four locking mechanisms in each corner . Place the rear slits in the plate over the rear brackets that hold the Fusing Assembly (Figure 6-12, callout 1). Lower the plate ov er the retaining clips, pressing on both sides of the Fuser Pressure Plate (Figure 6-12, callout, 2). It is important [...]
-
Page 91
Heating Element 1 Remove Printer Co v ers, Deli very Assembly (Figures 6-9 and 6-10), and Fuser Pressure Plate (Figure 6-11). 2 Remove the wire co ver (on the right side of the printer) for the Heating Element wires by pressing in on the tab and pulling outward (Figure 6-13, callout 1). Heating Element Removal (1 of 3) Figure 6-13 Remov al and Repl[...]
-
Page 92
3 Disconnect the A C v oltage to the Heating Element by releasing the connector located on the DC Controller . Press down on the connector release with a small, flathead scre wdri ver (Figure 6-14, callout 1). (Since this is a small space, it is much easier to reach the connector with a scre wdri ver .) Pull straight out (Figure 6-14, callout 2). H[...]
-
Page 93
4 Remov e the wire from the wire guides along the right-side of the printer . 5 Disconnect the thermistor feedback connector in the left front side of the Fusing Assembly (Figure 6-15). Heating Element Removal (3 of 3) 6 Lift the Heating Element out. Figure 6-15 Remov al and Replacement 6 - 19[...]
-
Page 94
Pressur e Roller 1 Remove Printer Cov ers, Deli very Assembly (Figur es 6-9 and 6-10), Fuser Pressur e Plate (Figure 6-11), and Heating Element (Figures 6-13 through 6-15). 2 Remove the Pressure Roller guide by lifting the edge (Figure 6-16, callout 1) and then rolling it gently backward (Figure 6-16, callout 2). Pressure Roller Removal 3 Lift the [...]
-
Page 95
F ace-Up/F ace-Down Le ver 1 Remove Printer Cov ers, Deli very Assembly (Figur es 6-9 and 6-10), Fuser Pressur e Plate (Figure 6-11), and Heating Element (Figures 6-13 through 6-15), and Pressure Roller (Figure 6-16). 2 Rotate the lev er forward 90 degrees (past the spring) and pull it straight out the front of the printer . To reinstall 1 Make sur[...]
-
Page 96
Fuser Exit Roller Assembly 1 Remove Printer Cov ers, Deli very Assembly (Figur es 6-9 and 6-10), Fuser Pressur e Plate (Figure 6-11), and Heating Element (Figures 6-13 through 6-15), Pressure Roller (Figure 6-16), and Face-Up/Face-Do wn L e v er (Figure 6-17). 2 Remove the gear from the left end of the roller shaft. 3 Remove the Exit Roller Assembl[...]
-
Page 97
Paper Exit Sensor Flag 1 Remove the Printer Covers, Deli very Assembly (Figures 6-9 and 6-10), and Fuser Pressure Plate (Figure 6-11). 2 Remove the P aper Exit Sensor flag by pressing do wn on the left side and pulling up on the right side. To reinstall Note It is important that you reinstall the flag correctly , since installing it incorrectly wil[...]
-
Page 98
T op Assemblies Laser/Scanner Assembly 1 Remove the Printer Co v ers. 2 Remove both Laser/Scanner connectors (Figure 6-20, callout 1). 3 Remove all (4) scre ws and lift the assem bly straight off (Figure 6-20, callout 2). Laser/Scanner Assembly Removal Figure 6-20 6 - 24 Removal and Replacement[...]
-
Page 99
Solenoid 1 Remove the Printer Co v ers. 2 On the left side of the printer , remove the paper pickup gear (Figure 6-21, callout 1) by pressing the tabs in the center of the gear outward and pulling the gear of f (Figure 6-21). Solenoid Removal (1 of 2) Figure 6-21 Remov al and Replacement 6 - 25[...]
-
Page 100
3 Remove the Solenoid connector (J204) from the DC Controller (Figure 6-22, callout 1). 4 Remove the self-tapping scre w that holds the Solenoid in place (Figure 6-22, callout 2). 5 Unthread the wires from the printer chassis. 6 Lift the Solenoid off. Solenoid Removal (2 of 2) Note When reinstalling this part, the Paper Pickup Gear is ke yed to go [...]
-
Page 101
Pickup Roller Assembly 1 Remove the Printer Co v ers. 2 Remov e the paper pickup gear (Figure 6-21). Note This gear is keyed to go on the shaft in only one w ay . 3 Remove the pickup roller grounding clip on the right of the printer by lifting each end up and over the tw o metal guides and sliding the clip off (6-23). Pickup Roller Assembly Removal[...]
-
Page 102
4 Using needlenose pliers, pull the bottom of the bushing out (Figure 6-24, callout 1), then turn it counter clockwise to release it (Figure 6-24, callout 2). Pickup Roller Assembly Removal (2 of 2) 5 Lift the bushing out. 6 From inside the front of the printer , slide the right side of the Pickup Roller Assembly forward, then lift the left side ou[...]
-
Page 103
To reinstall Note It is important that the Pickup Roller is placed back in with the two Idler Roller tabs up, so that they f it into the underside of the metal chassis behind the Laser/Scanner assembly (Figure 6-25). Paper Pickup Roller Assembly Replacement (Inside/Front View) Figure 6-25 Remov al and Replacement 6 - 29[...]
-
Page 104
Paper F eed Frame 1 Remove the Printer Co v ers. 2 Remove the Pickup Roller Assembly (Figures 6-23 through 6-24). 3 Release the connectors from the Laser/Scanner , T op Co ver/EP Cartridge Sensor (PS203), Switch 101, Front Control Panel (Figure 6-26). Disconnect the Solenoid from the DC Controller at J204 (Figure 6-22, callout 1). Paper Feed Frame [...]
-
Page 105
4 Remove the (4) he x head screws from the P aper Feed Frame (Figure 6-27, callout 1). 5 Remove the self-tapping scre w from the back sheet metal plate and lift it off (Figure 6-27, callout 2). Paper Feed Frame Removal (1 of 2) Figure 6-27 Remov al and Replacement 6 - 31[...]
-
Page 106
6 Release the sensor unit connector (Figure 6-28). Paper Feed Frame Removal (2 of 2) 7 Pull the frame straight back to remove it. To reinstall The Paper Feed Frame may be easier to reinstall if you place the printer on its front, so that you can apply pressure while putting the screws back in place. Figure 6-28 6 - 32 Removal and Replacement[...]
-
Page 107
T ransfer Roller Guide & T ransfer Roller 1 Remove the Printer Co v ers, Pickup Roller Assembly (Figures 6-23 through 6-25), and Paper Feed Frame (Figures 6-26 through 6-28). 2 Looking at the back of the printer , note the two small, hook-shaped release tabs on each end of the T ransfer Roller guide. Using a small, flathead scre wdri ver , care[...]
-
Page 108
Kick Plate 1 Remove the Printer Co v ers and the Pickup Roller Assembly (Figures 6-23 and 6-24). 2 Press the Separation Pad (Figure 6-30). Allow the Kick Plate to pi v ot upward (a spring underneath will push it up). Lift the Kick Plate off its mounting pins. Kick Plate Removal Figure 6-30 6 - 34 Removal and Replacement[...]
-
Page 109
To reinstall If the spring on the Kick Plate doesn’t stay on the Kick Plate, replace the spring, making certain the diameter of the spring surrounds two lo wer pins on the Kick Plate and rests inside the third pin. Use needlenose pliers to place the spring correctly . (See Figure 6-31.) Kick Plate Spring Replacement While rotating the Kick Plate [...]
-
Page 110
Separation Pad 1 Remove the Printer Co v ers, Pickup Roller Assembly (Figures 6-23 and 6-24), and Kick Plate (Figure 6-30). 2 Lift the bottom of the white plastic tab on the rear of the Paper Feed Frame up slightly and slide it up, tow ard the top of the Paper Feed Frame. This will release the Separation Pad (Figure 6-32). 3 Lift the Separation Pad[...]
-
Page 111
Subpads Note When you replace the Separation Pad, you should also replace the smaller subpads at the same time. 1 Place your index f i nger on the subpad. 2 Press tow ard the top of the printer . Subpad Removal Figure 6-33 Remov al and Replacement 6 - 37[...]
-
Page 112
F eed Assembly The Feed Assembly is located in the Paper Feed Frame. 1 Remove the Printer Co v ers, Pickup Roller Assembly (Figures 6-23 through 6-25), and Paper Feed Frame (Figures 6-26 through 6-28). 2 T urn the Paper Feed Frame upside do wn. 3 Remove the idler roller by lifting the plastic tab up (Figure 6-34, callout 1) and sliding it out the s[...]
-
Page 113
4 Remove the self-tapping scre w that holds the Feed Assembly in place (Figure 6-35, callout 1). Feed Assembly Removal (2 of 3) Figure 6-35 Remov al and Replacement 6 - 39[...]
-
Page 114
5 Remove the Feed Assembly . 6 T urn the unit ov er . Lift the paper feed roller out (Figure 6-36). Feed Assembly Removal (3 of 3) To reinstall Before securing the scre w , ensure the tabs on the Feed Assembly are positioned in their slots on the Paper Feed Frame (Figure 6-35, callout 2). Failure to do so will cause paper feed problems. Figure 6-36[...]
-
Page 115
Bottom Assemblies Memory Door Guide 1 Remove the Printer Co v ers. 2 Remove an y extra memory . 3 T wo tabs hold the memory door guide on the printer chassis. Press each tab inward (Figure 6-37). 4 Pull the memory door guide out. Memory Door Guide Removal Figure 6-37 Remov al and Replacement 6 - 41[...]
-
Page 116
Motor 1 Remove the Printer Co v ers. 2 Remove the motor connector (Figure 6-38, callout 1). 3 Remov e the memory door guide to e xpose the two motor scre ws. 4 Remove the motor scre ws (Figure 6-38, callout 2). 5 Lift the Motor out. Motor Removal Figure 6-38 6 - 42 Removal and Replacement[...]
-
Page 117
DC Controller 1 Remove the Printer Co v ers. 2 Disconnect the motor connector from the motor (Figure 6-38, callout 1). 3 Disconnect the Solenoid connector from the DC Controller (Figure 6-22, callout 1). 4 Remove the back sheet metal plate and disconnect the PS202/PS204 connector (Figure 6-28). 5 Remove the A C Cable cover and disconnect the A C Ca[...]
-
Page 118
8 Rotate the case forward slo wly , about three or four inches, until you can see the Fusing Assembly connector (J206). Release the connector (Figure 6-40, callout 1). Caution ESD SENSITIVE!!!! DC Controller Removal (2 of 3) Figure 6-40 6 - 44 Removal and Replacement[...]
-
Page 119
9 Rotate the metal case around so that the case is sitting on your work surface. 10 Remove the (7) remaining connectors (Figure 6-41, callout 1). 11 Remove the scre ws (5) that secure the DC Controller to the metal case (Figure 6-41, callout 2). DC Controller Removal (3 of 3) 12 Remove the DC Controller by lifting gently on the side opposite the fo[...]
-
Page 120
F ormatter PCA Caution ESD SENSITIVE!!! 1 Remove the Printer Co v ers and complete the DC Controller removal direction up to step 8 (Figures 6-39 and 6-40). 2 Remove the tw o cable clips (Figure 6-42, callout 1). 3 Remove all (4) scre ws from the formatter cover (Figure 6-42, callout 2). Lift the I/O shield to remove it. 4 Remove the Control P anel[...]
-
Page 121
7 T r oubleshooting Contents General T roubleshooting Flo wchart . . . . . . . . . . . . . . . . . . . . . . 7-3 Paper Path and Components . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5 DC Controller Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6 Printer Error T roubleshooting . . . . . . . . . . . . . . . . . . . . . [...]
-
Page 122
7-2 T roubleshooting[...]
-
Page 123
General T r oubleshooting Flowchart When the ac power is first applied to the printer: • • Both the printer motor and the laser/scanner motor rotate for 6 seconds. • • All of the LEDs illuminate for one second; the “Ready” LED will illuminate after 3 seconds. If no error message is displayed, the Printer Door is firmly closed, and the t[...]
-
Page 124
General T r oubleshooting Flo wchart (continued) Refer to the section “Image Formation Troubleshooting,” later in this chapter. If the engine test produces a clear print image, yet a Self Test is not generated by initiating the Control Panel self-test procedure, replace the Formatter PCA. Perform an Engine Test Is the Engine Test image being pr[...]
-
Page 125
Paper P ath and Components Paper Path and Components PS201 PS203 PS202 SL1 Motor Feed Roller Feed Sub Roller Pick-up Roller Paper Registration Sensor Paper Out Sensor Paper Pick-up Solenoid Photo- sensitive Drum Transfer Roller Fuser Paper Exit Sensor Fusing Unit Delivery Roller Face-up Delivery Deflector Face-down Delivery Face-down Delivery Rolle[...]
-
Page 126
DC Contr oller Diagram DC Controller PCA Components J3 Control P anel Connector (Formatter PCA) J202 Paper Registration and P aper-Out Photosensors (PS203 and PS202) J102 Fusing Assem bly J206 Fusing Assembly (thermistor feedback) J201 Formatter PCA Connection J207 Scanner Motor J204 Paper Pickup Solenoid (SL1) J208 Laser Dri ver/Beam Detect Circui[...]
-
Page 127
Printer Err or T r oubleshooting Information regarding printer status is con veyed by two methods: 1) the printer’ s Control Panel lights and 2) feedback through the bi-directional I/O that displays at the PC. The basic method of determining error messages uses patterns of lights on the Control Panel LED. Printer messages are categorized into tw [...]
-
Page 128
Printer Status Messages The following table lists printer LED messages and their meanings and describes recommended actions. For more information on the Front Panel layout, refer to “Using the Control Panel” in Chapter 3, “Installation and Conf iguration. ” LEDs Description Recommended Action P aper Out Err or . Door Open or No EP Cartridge[...]
-
Page 129
Occasionally you may add paper , close the printer door , add the toner cartridge, and clear a paper jam, only to find that the printer still displays an error message. If this happens, troubleshoot using T able 7-3 belo w . Note If the error appears and persists only after you attempt to print a page, verify that the motor is functioning. (See “[...]
-
Page 130
Service and Err or Messages Service errors prev ent further printer operation until some action is taken. When there is a service error , all of the lights will turn on in a steady state. P ress and hold the Front P a nel Button to see a pattern in the lights. (The error will only be displayed as long as this button is pressed.) Use T able 7-4, “[...]
-
Page 131
Heating Element Resistance Check Figure 7-3 LEDs Description Recommended Action Beam Err or . There are a number of causes for thi s error , and some of the causes may be transient. (They ma y disappear .) 1. P ower-cycle the printer b y unplugging the printer and plugging it bac k in. 2. Make certain the Laser/Scanner Assembly i s correctly seated[...]
-
Page 132
LEDs Description Recommended Action Scanner Err or . Caus ed by a scanner malfunction. 1. P ower-cycle the printer b y unplugging the printer and plugging it bac k in. 2. Ensure condensation c aused by mo ving the printer from a cold to a warm environment hasn’ t oc curred. Allow the printer to acclimate to the warmer room. 3. V er ify the two La[...]
-
Page 133
Image F ormation T r oubleshooting Check the T oner Cartridge Image formation defects are many times the result of toner cartridge problems. If there is any doubt, alw ays replace the toner cartridge before troubleshooting image defects. Use the following check list to ensure that the toner cartridge is still operable. • • Ensure that the toner[...]
-
Page 134
Image Defect Examples This section illustrates some image defects and their possible causes. Since there are many v ariables in the printing process, you may encounter image defects that are not illustrated in the following e xamples. If you find a defect that is not illustrated, record the probable cause along with the printing en vironmental cond[...]
-
Page 135
V ertical Lines Sometimes vertically aligned black streaks or smears can appear on successi ve pages. • The toner cartridge may be damaged. Replace it. • The printer may need cleaning. See “Cleaning Your Printer,” in Chapter 4. • Replace the heating element. Horizontal Stripes Sometimes horizontally aligned black streaks or smears can app[...]
-
Page 136
Character V oids Character voids are white areas within the parts of characters that should be solid black. • If you are using transparencies when you experience this problem, try another type of transparency. Hewlett-Packard transparencies are designed to minimize character voids. (Because of the composition of transparency media, some character[...]
-
Page 137
Dropouts Dropouts are characters that are partially printed. • The Paper Input Bin may have been loaded with too much paper. Make sure that no more than 100 sheets of paper are loaded. • A single sheet of paper may be defective. Try reprinting the job. • Try adjusting the print density through your software or printer driver. • Try cleaning[...]
-
Page 138
Blank Page (Occasional) A page is completely blank. If you get occasional blank pages: • Make sure your page length and margins are set correctly for the paper size you use. If you are printing on small media and your page is blank, try printing on larger media to see where the image is printing. Adjust margins accordingly. • Some sharing devic[...]
-
Page 139
Dots • Clean the static charge eliminator. (See Chapter 4, “Printer Maintenance.") • There may be discontinuities in the high-voltage contact points. Clean the high voltage contact points on the toner cartridge and transfer roller. • Replace the transfer roller. Dirt on the Back of the Page • Use the image defect ruler to determine i[...]
-
Page 140
Distorted Image or BD Failure • Make certain the printer is not facing the sunlight. • The paper may not meet HP’s paper specifications. Select different paper. • Clean the Laser/Scanner Assembly by blowing compressed air in the slot on the bottom of the assembly. • Make sure the two Laser/Scanner connectors are firmly seated. • Replace[...]
-
Page 141
T r oubleshooting Checks Engine T est The engine test print is used to verify that the print engine is functioning correctly . The Formatter PCA is completely bypassed during an engine test, so this test is useful for isolating printer problems. The engine test prints a full page of v e rtical lines down the entire printable area and is also useful[...]
-
Page 142
Half-Self T est Functional Check The electrophotographic process can be subdivided into the follo wing stages: • • Cleaning (removing excess toner from drum surface) • • Conditioning (placing a uniform electrical charge on drum) • • Writing (laser strikes surface of drum to create latent image) • • Development (formation of the tone[...]
-
Page 143
Drum Rotation Functional Check The photosensitiv e drum, located in the toner cartridge, must rotate for the print process to work. The photosensiti ve drum recei ves its driv e from the Main Driv e assembly . T o v erify whether the drum is rotating: 1 Open the Printer Door . 2 Remove the toner cartridge. 3 Mark the cartridge’ s driv e gear with[...]
-
Page 144
High-V oltage Po wer Supply Check The High-V oltage Power Supply PCA provides the necessary v oltages for the electrophotographic processes. A method for verifying the high-v oltage system is giv en in the table below . Toner Cartridge High Voltage Connection Points (1 of 2) • • Charging (1) • • Drum Ground (2) • • Developing Roller (3)[...]
-
Page 145
Toner Cartridge High Voltage Connection Points (2 of 2) • • Charging (1) • • Drum Ground (2) • • Developing Roller (3) Figure 7-6 T roubleshooting 7-25[...]
-
Page 146
Paper Curl Paper curl is inherent to the laser printing processes, and occurs when paper is subjected to heat. Paper curl tends to relax as the paper cools while resting on a flat surface. The specification for maximum paper curl when the paper is lying flat before print is 5 mm (0.2 inches). Although paper curl cannot be totally eliminated, some s[...]
-
Page 147
T r oubleshooting T ools Paper P ath Check If paper is not being picked up or is not mo ving through the paper path, you may want to observ e all of the paper motion acti vities. Overriding PS204 allows you to observe: • • Motor rotation • • Solenoid action • • Kick plate motion • • Paper Pickup Roller motion • • Drive Roller, T[...]
-
Page 148
Repetitive Image Defect Ruler Repetitive Image Defect Ruler Figure 7-8 7-28 T roubleshooting[...]
-
Page 149
Main Wiring Diagram Figure 7-9 Main Wiring Diagram T roubleshooting 7-29[...]
-
Page 150
Connector Signal Name Remarks J401 pin 1 MA Motor Drive S ignal J401 pin 2 /MA Motor Drive S ignal J401 pin 3 MB Motor Drive S ignal J401 pin 4 /MB Motor Drive S ignal J204 pin 1 +12 V J204 pin 2 CPUD Solenoid S L1 Pick up Drive J202 pin 1 +5V J202 pin 2 GND J202 pin 3 P APSENS “L ” when PS202 detects paper J202 pin 4 +5V J202 pin 5 GND J202 pi[...]
-
Page 151
Connector Signal Name Remarks J209 pin 3 DOSNS “H” when car tridge is not installed or the front door is open at PS204. J305 pin 1 +12A V J305 pin 2 N/U J305 pin 3 +12 V J206 pin 1 FRSTH Fusing temperature f eedback J206 pin 2 FG J102 pin 1 Fusing assemb ly drive v oltage J102 pin 2 Fusing assemb ly drive v oltage Table 7-8 Cable Pinouts T roub[...]
-
Page 152
7-32 T roubleshooting[...]
-
Page 153
8 Parts and Diagrams Contents Ho w to Use the P art Lists and Diagrams . . . . . . . . . . . . . . . . . . . . 8-3 Ordering Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3 Ordering Consumables . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4 Accessories and Supplies . . . . . . . . . . . . . . . . . . . . . . . . [...]
-
Page 154
8-2 Parts and Diagrams[...]
-
Page 155
How to Use the P art Lists and Diagrams The Figures in this chapter illustrate the major subassemblies in the printer and their component parts. A table (material list) follows each e xploded assembly diagram. Each table lists the reference designator (item number) for each part, the associated part number for the item, the quantity , and a descrip[...]
-
Page 156
Ordering Consumables Consumables and accessories such as those listed on T able 8-1 may be ordered from He wlett-Packard. The phone numbers are: U.S.: 1-800-538-8787 Canada: 1-800-387-3154 (T oronto) 516-671-8383 United Kingdom: 0734-441212 Germany: 0130-3322 Contact your local HP Parts Coordinator for other local phone numbers. Note Parts that ha [...]
-
Page 157
Accessories and Supplies The following items are a v ailable through your local authorized HP dealer . T o find a dealer near you (or if your dealer is temporarily out of stock), call the HP Customer Information Center (800) 752-0900. Note Refer to “Related Documentation” in Chapter 1 for documentation and training media product numbers. Note Y[...]
-
Page 158
Common Hardwar e Example Description Screw , Machine , T rus Head M3x4, M3x6, M3x8 Scre w , Star , 3x6 Screw , Self-tap , 4x10 Screw , Hex-head, 3x 8 Scre w , He xhead, 3x6,m 3x8, 3x10 Table 8-2 Common Fasteners Used in the Printer 8-6 Parts and Diagrams[...]
-
Page 159
Major Assembly Locations Figure 8-1 Parts and Di agra ms 8-7[...]
-
Page 160
Covers and Doors Figure 8-2 8-8 Parts and Diagrams[...]
-
Page 161
Ref. Part No. Ref. Description 1 RB1-7211-000CN 1 Input Extender 1 2 RB1-7212-000CN 1 Input Extender 2 3 RB1-7333-000CN 1 Bac k Cover 4 RB1-1995-000CN 1 Main Cov er 4A RB1-7278-000CN 1 F ace-up/F ace-down Swi tch 5 RB1-7326-000CN 1 Output Extender 1 6 RB1-7327-000CN 1 EP Door Chimney 7 RB1-7331-000CN 1 Output Extender 2 8 RF5-1501-000CN 1 EP Door A[...]
-
Page 162
Internal Components (1 of 3) Figure 8-3 8-10 Parts and Diagrams[...]
-
Page 163
Ref Part No. Qty Description 1 R Y7-5005-000CN 1 Gear K it #1 2 RB 1-7288-000CN 2 Exit Roller Bushi ng 3 RB 1-7105-000CN 1 Fus er Releas e T ab 4 RB 1-7106-000CN 1 Gear Plate 5 RB1-7107-000CN 1 F ront Gear Case 6 RY7-5007-000CN 1 Fuser Release Assemb ly 7 RH7-1282-000CN 1 Main Motor 8 RY7-5006-000CN 1 Gear Kit #2 16 RG5-1984-000CN 1 EP/Cov er Inter[...]
-
Page 164
Internal Components (2 of 3) Figure 8-4 8-12 Parts and Diagrams[...]
-
Page 165
Ref Part No. Qty Description 1 RB1-7109-000CN 1 Memory Door Guide 2 RB1-7247-000CN 1 Fuser P aper Guide 3 RB1-7344-000CN 1 A C Cable Cov er 4 RF5-1509-000CN 1 Bac k Sheet Metal 5 RB1-7343-000CN 1 Control P anel Cable Guide 6 RB1-7130-000CN 1 Fuser Cab le Guide 7 RB1-7234-000CN 1 Cap 8 RB1-7302-000CN 1 Cap 9 XA9-0724-000CN 6 Scre w , RS , M3x8 10 XA[...]
-
Page 166
Internal Components (3 of 3) Figure 8-5 8-14 Parts and Diagrams[...]
-
Page 167
Ref Part No. Qty Description 1 RB1-7223-000CN 1 Pic kup Roller Grounding Clip 2 RB1-7246-000CN 2 PR Bushing 3 RB1-7341-000CN 1 EP Right Hand Guide #2 4 RF5-1516-000CN 1 Pressure Rol ler 5 RF5-1517-000CN 1 Fuser Pres sure Plate 6 RF5-1530-000CN 1 T ransf er Roller Guide 7 RF5-1534-000CN 1 T ransf er Roller 8 RB1-7129-000CN 1 Case Ground Metal 9 RF5-[...]
-
Page 168
DC Controller/Formatter and Cables Figure 8-6 8-16 Parts and Diagrams[...]
-
Page 169
The table below lists each connector , its cable length, and the number of pins. Connector Cable Length (inches) Number of Pins Fusing Assemb ly (J206) 5.5 (14 cm) 2 Laser Driver/Beam Detec t Circuitry (J208) 21 (53 cm) 6 Door Open/No EP Car tridge (PS203) (J209) 14 (35 cm) 3 Scanner Motor (J 207) 14.5 (37 cm) 5 P aper Registration (P S202)/P aper [...]
-
Page 170
Pickup Roller Assembly Figure 8-7 8-18 Parts and Diagrams[...]
-
Page 171
Ref Part No. Qty Description 1 RB1-7177-000CN 1 P aper F eed F rame 2 RY7-5008-000CN 1 Separation P ad Assembly 3 RY 7-5009-000CN 1 Input Sensor Assembly 4 RG5-1940-000CN 1 Pic kup Roller Assembly 5 RB1-7184-000CN 1 Pic kup Roller Bushing 6 RB1-7197-000CN 1 Clutch 7 RB1-7199-000CN 1 Bac k Grounding Clip 9 RG5-1947-000CN 1 Idler Roller S haft Assemb[...]
-
Page 172
Feed Assembly Figure 8-8 8-20 Parts and Diagrams[...]
-
Page 173
Ref Part No. Qty Description RG5-1942-000CN 1 Feed Assemb ly 9 RB1-7226-000CN 1 Idler Roller Table 8-8 Parts and Di agra ms 8-21[...]
-
Page 174
Separation Guide Assembly Figure 8-9 8-22 Parts and Diagrams[...]
-
Page 175
Ref Part No. Qty Description RG5-2013-000CN 1 Separation Guide Assemb ly 2 RB1-7276-000CN 1 F ace-up/face-do wn Shaft 4 RB1-7289-000CN 1 Fuser Roller Bushi ng 7 RF5-1522-000CN 1 Fuser Exit Rol ler Assembly Table 8-9 Parts and Di agra ms 8-23[...]
-
Page 176
Delivery Assembly Figure 8-10 8-24 Parts and Diagrams[...]
-
Page 177
Ref Part No. Qty Description RG5-2012-000CN 1 Delivery Assembly 1 RB1-7284-000CN 4 Delivery Roller #1 2 RB1-7285-000CN 2 Delivery Roller #2 3 RB1-7286-000CN 4 Deliv er y Spring#1 4 RB1-7287-000CN 2 Deliv er y Spring#2 6 RG5-2015-000CN 2 Spur Assemb ly Outside 7 RG5-2014-000CN 2 Spur Assemb ly Inside Table 8-10 Parts and Di agra ms 8-25[...]
-
Page 178
8-26 Parts and Diagrams[...]
-
Page 179
A Parts Index Parts Index A-1[...]
-
Page 180
Parts Index Description Part No. Fig. Ref. A C Cable Cov er RB1-7344-000CN 8-5 3 Back Cover RB1-7333-000CN 8-2 3 Back Grounding Clip RB1-7199-000CN 8-7 7 Back Sheet Metal RF5-1509-000CN 8-5 4 Cap RB1-7234-000CN 8-5 7 Cap RB1-7302-000CN 8-5 8 Case Grounding Metal RB1-7129-000CN 8-4 8 Clutch RB1-7197-000CN 8-7 6 Control P anel Cable Guide RB1-7343-00[...]
-
Page 181
Description Part No. Fig. Ref. F eed Assembly RG5-1942-000CN 8-8 Flag RB1-7293-000CN 8-4 18 Flag Cov er RF5-1524-000CN 8-6 2 Flag Spring RB1-7294-000CN 8-4 19 F or matter Shield RG5-2024-000CN 8-6 1 F or matter (Exchange) C3942-67902 110 2 F or matter (New) C3942-69002 110 2 F ront Gear Case RB1-7107-000CN 8-3 5 Fuser Cable Gui de RB1-7130-000CN 8-[...]
-
Page 182
Description Part No. Fig. Ref. Kic k Plate P a d RB1-7178-000CN 8-7 20 Kic k Plate Spring RS5-2501-000CN 8-7 14 Label (110V) RS5-8540-000CN 8-2 12 Label (240V) RS5-8541-000CN 8-2 12 Laser Cable RG5-2035-000CN 8-6 13 LaserScanner (Exchange) C3941-69003 LaserScanner (Ne w) RG5-2000-000CN 8-3 19 Left Leg RB1-7185-000CN 8-7 16 Left Pressure Roller Ho[...]
-
Page 183
Description Part No. Fig. Ref. Right Sub P ad Assembly RF5-1493-000CN 8-7 12 Rock er Arm RB1-7219-000CN 8-7 19 Rock er Holder RB1-7220-000CN 8-7 10 Scanner Cable RG5-2034-000CN 8-6 12 Screw XA9-0724-000CN 8-2 11 Screw XA9-0813-000CN 8-5 10 Screw XB1-1300-807CN 8-5 502 Screw XA9-0267-000CN 8-3 503 Screw XA9-0824-000CN 8-4 17 Screw XA9-0686-000CN 8-4[...]
-
Page 184
Part No. Description Fig. Ref. C3941-69001 DC Controller PCA (110V) Exchange 8-6 3 C3941-69002 DC Controller PCA (220V) Exchange 8-6 3 C3941-69003 Laser Scanner (Exchange) C3942-67902 Formatter (Exchange) 8-6 2 C3942-69002 Formatter (New) 8-6 2 RB1-1995-000CN Main Co ver 8-2 4 RB1-7105-000CN Fuser Releas e T ab 8-3 3 RB1-7105-000CN Fuser Releas e T[...]
-
Page 185
Part No. Description Fig. Ref. RB1-7255-000CN Left PR Housing 8-4 13 RB1-7256-000CN Right PR Hous ing 8-4 12 RB1-7276-000CN F ace-up/F ace-down Shaft 8-9 2 RB1-7278-000CN F ace-up/F ace-down Switch 8-2 4A RB1-7284-000CN Deliv ery Roller #1 8-10 1 RB1-7285-000CN Deliv ery Roller #2 8-10 2 RB1-7286-000CN Deliv ery Spr ing #1 8-10 3 RB1-7287-000CN Del[...]
-
Page 186
Part No. Description Fig. Ref. RF5-1522-000CN Fuser Exit Rol ler Assembly 8-9 7 RF5-1524-000CN Flag Co ver 8-6 2 RF5-1530-000CN T ransf er Roller Guide 8-4 6 RF5-1533-000CN PR Ground Guide 8-4 14 RF5-1534-000CN T ransf er Roller 8-4 7 RG5-1940-000CN Pickup Roller Assemb ly 8-7 4 RG5-1942-000CN Feed Assemb ly 8-8 RG5-1944-000CN Input Assembly 1 8-2 [...]
-
Page 187
Part No. Description Fig. Ref. RS5-0796-000CN PR Gear 8-4 11 RS5-2501-000CN Kic k Plate Spring 8-7 14 RS5-2502-000CN Main S eparation P ad Spring 8-7 15 RS5-8540-000CN Label (110v) 8-2 12 RS5-8541-000CN Label (240v) 8-2 12 R Y7-5005-000CN Gear Assemb ly #1 8-3 1 R Y7-5006-000CN Gear Assemb ly #2 8-3 8 R Y7-5007-000CN Fus er Release Assemb ly 8-3 6 [...]
-
Page 188
A-10 Part s Index[...]
-
Page 189
B Regulatory Inf ormation Laser Safety (U .S.A.) The Center for Devices and Radiological Health (CDRH) of the U.S. F ood and Drug Administration implemented regulations for laser products manuf actured since August 1, 1976. Compliance is mandatory for products marketed in the United States. This printer is certified as a “Class 1” laser product[...]
-
Page 190
Laser Statement (Finland) The following applies to printer operation and servicing in Finland. LASER TUR V ALLISUUS LUOKAN 1 LASERLAITE KLASS 1 LASER APP ARA T HP LaserJet(s) 4V and 4MV laserkirjoitin on käyttäjän kannalta turvallinen luokan 1 laserlaite. Normaalissa käyt"ssä kirjoittimen suojakotelointi estää lasersäteen pääsyn lait[...]
-
Page 191
T oner Safety Note In case of toner spills, skin and clothing are best cleaned by removing as much toner as possible with a dry tissue, then washing with cold water . Hot water causes toner to permanently set into clothing. MSDS Information A Material Safety Data Sheet (MSDS) for toner or any other chemical used in the printer is av ailable through[...]
-
Page 192
FCC Statement (Class B) Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency en[...]
-
Page 193
Index A A C po wer distrib ution 5-6 circuitry 5-6 accessories and supplies 8-5 acoustic emissions 1-5 assistance,technical 1-11 A UDIO-TIPS, HP 1-11 B background scatter 7-16 black page 7-16 blank page all pages 7-18 occasional 7-18 bottom a ssembies memory door guide 6-41 bottom assemblies DC Controller 6-43 formatter PCA 6-46 motor 6 -42 C cable[...]
-
Page 194
image transferring 5-12, 5 -14 image writing 5-12 - 5-13 installatio n DRAM 6-5 installing memory cards 6-5 printer 3-3 software 3-4 interfaces standard 1-3 internal as sembli es 8- 10, 8-12, 8- 14 control panel 6-11 delivery assembly 6-13 exit roller assembly 6-12 face-up/face-down lever 6-21 fuser exit ro ller 6-22 fuser pr essur e plate 6-15 hea[...]
-
Page 195
error 7-8 manual feed 7-7 memory error 7-7 paper out 7-7 Ready 7-8 self test 7-8 status 7-8 toner cartridge 7-7 troubleshooting 7-7 printer space requirements 2-4 printer timing 5-19 INTR 5-19 LSTR 5-19 PRNT 5-19 STBY 5-19 WAIT 5-19 printing self test page 3-14 priority of erro rs 7-7 PRNT , printer timing 5-19 product information 1-1 - 1-14, 3-1 -[...]
-
Page 196
print quality pro blems 7-14 printer erro rs 7-7 troubleshooting checks 7-21 troubleshooting flowchart 7-3 troubleshooting tools 7- 27 troubleshooting, prelimin ary 7-3 two-way communication, PJL 5- 11 typefaces internal 1-3 V VCCI Statement, Japan B-4 vertical lin es 7-15 vertical wh ite stripes 7-15 volta ge con versions 1-14 W W AIT , printer ti[...]