English dropdown-ico

HP COI 2180206H manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of HP COI 2180206H, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of HP COI 2180206H one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of HP COI 2180206H. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of HP COI 2180206H should contain:
- informations concerning technical data of HP COI 2180206H
- name of the manufacturer and a year of construction of the HP COI 2180206H item
- rules of operation, control and maintenance of the HP COI 2180206H item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of HP COI 2180206H alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of HP COI 2180206H, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the HP service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of HP COI 2180206H.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the HP COI 2180206H item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    Installation and operating instructions Combi HP Thermostatic mixer shower T00219 2180206H March 2007 I nstallers please note these InstructIons are t o b e left wIth the user[...]

  • Page 2

    Combi HP ther mostatic mixer shower Introduction 1 Safety warnings 1 Main components 2 Siting requirements 3 T ypical suitable installations 4 Preparing the mixer valve 6 Siting of the shower 6 Fitting the shower to the wall - Exposed 7 Rising and falling supplies 7 Rear entry supplies 1 0 Fitting the shower to the wall - Built-in 1 3 Solid wall 1 [...]

  • Page 3

    1 Combi HP ther mostatic mixer shower INTRODUCTION SAFETY W ARNINGS C-006-A INTRODUCTION T his book contains all the necessary fitting and operating instructions for your T riton high pressure thermostatic mixer shower . Please read them carefully . Please read through the whole of this book before beginning your installation. T he installation MU[...]

  • Page 4

    2 Combi HP ther mostatic mixer shower 1. Inlet nuts and olives 2. Inlet elbows 3. V alve housing 4. Outlet adaptor 5. Outlet nut and olive 6. Outlet blanking plug 7. Cartridge assembly 8. Flow knob 9. T emperature knob 10. Knob trim 11. Max. temperature override button 12. Cover 13. Inlet trims 14. Outlet trim 15. Outlet blanking trim 16. Flush mou[...]

  • Page 5

    3 Combi HP ther mostatic mixer shower SITING REQUIREMENTS D-003-A SITE REQUIREMENTS The installation must be in accordance with W ater Regulations/Bylaws. Minimum running water pressure: 1 bar . Maximum running water pressure: 5 bar . Maximum static water pressure: 10 bar . For the best performance within the specified pressure range both hot and [...]

  • Page 6

    4 Combi HP ther mostatic mixer shower a) Instantaneous gas-heated showers, e.g. combination boilers (fig.2) The shower control MUST be installed with a multipoint gas water heater or combination boiler of a fully modulating design (i.e. where the water draw-off rate indirectly controls the gas flow to the burner). A drop tight pressure reducing val[...]

  • Page 7

    5 Combi HP ther mostatic mixer shower packages with a cold take off after the pressure reducing valve to the cylinder . The layout and sizing of pipework must be such that nominally equal inlet supply pressures are achieved and the effects of other draw-offs are minimised. d) Mains pressurised thermal store (fig.5) Packages of this type, fitted wit[...]

  • Page 8

    6 Combi HP ther mostatic mixer shower Height of showerhead and shower to suit user ’s requirement. Shower can be mounted either side of the riser rail T00225 Before starting the installation, make sure all the openings on the valve are carefully covered to prevent ingress of any debris etc. Note: It is not necessary to remove the control knobs at[...]

  • Page 9

    7 Combi HP ther mostatic mixer shower Exposed Note: The outlet of the shower must not be connected to anything other than the hose and showerhead supplied. DO NOT use jointing compounds on any pipe fittings for the installation. DO NOT solder fittings near of the shower unit, as heat transfer can damage components. Note: Suitable isolating valves ([...]

  • Page 10

    8 Combi HP ther mostatic mixer shower T00022 Hose end (flat) Pipe end (chamfered) screws are slack allowing the inlet elbows to rotate to the correct position and move freely in and out of the valve housing (fig.8) . Place the valve housing centrally between the two pipes, and mark the two diagonal fixing holes (figs.9 and 1 0) . Remove the valve. [...]

  • Page 11

    9 Combi HP ther mostatic mixer shower If installing a riser rail, fit the outlet adaptor into the bottom outlet hole in the valve housing. The adaptor is sealed with an ‘O’ ring. Make sure the adapter is fitted with the pipe end in the valve housing (fig.17) Fit the blanking plug into the top outlet hole using an ‘O’ ring to seal it (fig.18[...]

  • Page 12

    10 Combi HP ther mostatic mixer shower Rear entr y supplies Note: The final separation between pipe centres needs to be about 153 mm but absolute accuracy is not essential as the inlet elbows are adjustable between 146 mm and 160 mm (fig.23) . Using a spirit level, mark the route of incoming hot and cold water supply pipes at a distance of 153 mm c[...]

  • Page 13

    11 Combi HP ther mostatic mixer shower Remove the valve. Drill and plug the holes using the wall plugs supplied. Using two hexagonal nuts (supplied), refit the valve to the pipework. Make sure the hot inlet port (marked with the letter ‘H’ on the valve housing) is connected to the hot pipework which must be on the left. Tighten the inlet nuts w[...]

  • Page 14

    12 Combi HP ther mostatic mixer shower where it is required i.e. bottom outlet for fixed head, top outlet for a hose (fig.20) . Fit the inlet blanking trims on the underside of the cover (fig.28) . Fit the outlet trim over the outlet adaptor and slide the cover on (fig.19) . Secure the cover with two screws (fig.21) . Locate the lugs on the trim ri[...]

  • Page 15

    13 Combi HP ther mostatic mixer shower FITTING THE SHOWER TO THE WALL - BUIL T -IN FITTING THE SHOWER TO THE W ALL Opening needs to be at the bottom if using a bulkhead 200 m m 10 - 12.5 m m 48 m m 50 mm 35 m m 77.5 m m 65 mm 220 mm T00249 Fig.29 T00250 Fig.30 Flush fit Note: The outlet of the shower must not be connected to anything other than the[...]

  • Page 16

    14 Combi HP ther mostatic mixer shower T00251 T00253 Seal tight up to shroud T00252 Fig.31 Fig.32 Fig.33 shower from the top (falling), the bottom (rising) or the rear . Mark the route of the incoming and outgoing pipework. Note: The final separation between pipe centres needs to be about 153 mm but absolute accuracy is not essential as the inlet e[...]

  • Page 17

    15 Combi HP ther mostatic mixer shower Where this is not possible refer to the ‘flushing procedure’ on page 20. Refit the valve to the mounting bracket/wall surface and pipework (fig.32) . Tighten the inlet nuts and inlet elbow grub screws. If fitting a fixed head, refer to the ‘Fitting the fixed head’ section and complete the outlet pipewo[...]

  • Page 18

    16 Combi HP ther mostatic mixer shower Fit the flush mount cover (fig.37) . Locate the lugs on the trim ring in the holes on the cover (fig.38) and twist clockwise. Complete the fitting of your shower accessories. Hollow wall The wall mounting bracket supplied with the shower is suitable for use on a plasterboard wall of 9.5 mm or 12.5 mm in thickn[...]

  • Page 19

    17 Combi HP ther mostatic mixer shower washer . Make sure the inlet elbows are positioned the correct way . Offer the valve up to the mounting bracket and secure using the screws provided (fig.42) . Complete the pipework to the shower marking off the length to enter the elbows. Remove the valve and cut the pipes to length. Flush pipework to clear t[...]

  • Page 20

    18 Combi HP ther mostatic mixer shower T00253 Seal tight up to shroud drill and plug the holes. Note: If fitting to plasterboard, use suitable cavity fixings. Break off the alignment tabs on the flush mount plate (fig.36). Place a ring of silicon sealant round the plate so that the plate seals against the wall. Secure the plate to the wall using th[...]

  • Page 21

    19 Combi HP ther mostatic mixer shower correct way . Offer the valve up to the mounting bracket and secure using the screws provided. Secure the mounting bracket together with the valve to the panel using two bolts in the innermost fixing holes (fig.46) . Complete the pipework to the shower marking off the length to enter the elbows. Remove the val[...]

  • Page 22

    20 Combi HP ther mostatic mixer shower Removal and/or fitting of check valves for maintenance IMPORT ANT : It is preferable to flush the pipework before installing the valve. Where this is not possible, the procedure using a flushing cartridge should be followed. a. Isolate the supplies. b. Remove the trim ring by twisting anti- clockwise. c. Remov[...]

  • Page 23

    21 Combi HP ther mostatic mixer shower FITTING THE T AMPERPROOF FIXED HEAD - EXPOSED FITTING THE T AMPERPROOF FIXED HEAD (Exposed option only) Complete the outlet pipework from the valve and cut the pipe to required length. Place the fixed head unit on top of the pipe work and mark the position of the three fixing holes (fig.54) . Drill and plug th[...]

  • Page 24

    22 Combi HP ther mostatic mixer shower FITTING THE T AMPERPROOF FIXED HEAD - BUIL T -IN FITTING THE T AMPERPROOF FIXED HEAD (Built in option only) Complete outlet pipework from the valve ending in a ½” BSP female threaded fitting (not supplied) (fig.59) . Note: The depth of thread on the fixed head unit from wall surface is 18 mm (fig.60) . It i[...]

  • Page 25

    23 Combi HP ther mostatic mixer shower FITTING THE FIXED HEAD - BUIL T -IN FITTING THE FIXED HEAD (Built in option only) The outlet pipe should protrude from the surface of the wall between 50 mm and 65 mm (fig.65) . Mark four fixing hole positions by using the fixed arm as a template. Drill and plug the wall using the plugs supplied. Care must be [...]

  • Page 26

    24 Combi HP ther mostatic mixer shower T00081 Appropriate fitting (Riser rail option only) Complete the outlet pipework ending in a ½" x 15 mm female thread fitting (fig.68) . Note: This fitting is not supplied as variations in installations needs the selection of the most suitable fitting. Screw the supplied male-thread connector into the fe[...]

  • Page 27

    25 Combi HP ther mostatic mixer shower Make sure all plumbing supplies are connected and turned on. Starting the shower T o start the shower , turn the outer knob (flow control) anti-clockwise (fig.74) . Adjusting the shower temperature T o adjust the temperature, turn the inner knob — temperature control (fig.75) . The temperature disc is number[...]

  • Page 28

    26 Combi HP ther mostatic mixer shower T00297 0D[LPXPWHPSHUDWXUHVWRSPHFKDQLVP 'HFUHDVHVWRSSRVLWLRQ,QFUHDVHVWRSSRVLWLRQ 7 5 , 7 2 1  7 5 , 7 2 1  *URRYHV 7 HPSHUDWXUHFRQWUROGLVF T00296 Fi xi ng sc re w T e mp era tu re co nt ro l k no b T e mp era tu re co nt ro[...]

  • Page 29

    27 Combi HP ther mostatic mixer shower T00298 1. HP valve cartridge (built-in valve) 83304970 2. HP cartridge and brass housing (exposed valve) 83304960 3. Outlet adaptor chrome 7031462 gold 7031463 4. Inlet elbow assembly 83303810 5. Outlet blanking plug 7031460 6. Cartridge ‘O’ rings 83303710 7. Knob set − white 83304810 8. Knob trim 705146[...]

  • Page 30

    28 Combi HP ther mostatic mixer shower T00299 SP ARE P ARTS 14. Bulkhead assembly white 83303780 chrome effect 83303770 gold effect 83303790 − T rim disc (use with flush gold effect) 7051451 15. Inlet & outlet nuts 83303660 16. Spanner 7011766 − Flow regulator 22003530 17. Check valve/sleeve assembly 83303810 18. W all bracket 7011453 19. C[...]

  • Page 31

    29 Combi HP ther mostatic mixer shower X-006-A T urn the control knob anti-clockwise. T urn the control anti-clockwise. Reduce the simultaneous demand from supply — make sure a dedicated supply to mixer . Contact Customer Service for advice on flow regulators. Clean – refer to ‘Flushing Procedure’ . T urn the temperature control clockwise.[...]

  • Page 32

    30 Combi HP ther mostatic mixer shower FAUL T FINDING Problem/Symptom Cause Action/Cure X-006-A T urn t h e contro l k no b anti-c l oc k wise. T urn the control anti-clockwise. Reduce the simultaneous demand from supply — make sure a dedicated supply to mixer . Contact Customer Service for advice on flow regulators. Clean – refer to ‘Flushi[...]

  • Page 33

    31 Combi HP ther mostatic mixer shower[...]

  • Page 34

    32 Combi HP ther mostatic mixer shower[...]

  • Page 35

    33 Combi HP ther mostatic mixer shower[...]

  • Page 36

    T riton Showers T riton Road Nuneaton W arwickshire CV11 4NR T riton is a division of Norcr os Group (Holdings) Limited TRITON reserve the right to change product specification without prior notice. E&OA. © TRITON SHOWERS 2008 Service Policy In t he e ve nt of a c om pl ai nt oc cu rr in g, t he fo ll ow in g pr oc ed ur e sh oul d be f ol lo[...]