English dropdown-ico

Husqvarna 325LDX manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Husqvarna 325LDX, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Husqvarna 325LDX one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Husqvarna 325LDX. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Husqvarna 325LDX should contain:
- informations concerning technical data of Husqvarna 325LDX
- name of the manufacturer and a year of construction of the Husqvarna 325LDX item
- rules of operation, control and maintenance of the Husqvarna 325LDX item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Husqvarna 325LDX alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Husqvarna 325LDX, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Husqvarna service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Husqvarna 325LDX.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Husqvarna 325LDX item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    E E E E n n n n g g g g l l l l i i i i s s s s h h h h 323L 323LD 325CX 325LX 325LDX Oper ator ′ s manual Please r ead the operator’ s manual carefull y and make sur e you understand the instructions before using the machine.[...]

  • Page 2

    2 – English KEY T O SYMBOLS Symbols W ARNING! Clear ing saws , brushcutters and trimmers can be dangerous! Careless or incorrect use can result in serious or fatal injur y to the operator or others . Please read the oper ator’ s manual carefully and make sure y ou understand the instructions before using the machine . Alwa ys wear : • A prote[...]

  • Page 3

    English – 3 CONTENTS Contents Note the f ollowing bef ore star ting: Please read the oper ator’ s manual carefully . KEY T O SYMBOLS Symbols ....................................................................... 2 CONTENTS Contents ...................................................................... 3 Note the f ollowing bef ore star ting: .[...]

  • Page 4

    4 – English INTR ODUCTION Dear Customer , Cong ratulations on y our choice to buy a Husqv arna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Charles XI ordered the construction of a factory on the banks of the Husqvarna River , for production of musk ets. T he location was logical, since w ater power w [...]

  • Page 5

    English – 5 WHA T IS WHA T? What is what? 1 T rimmer head 2 Grease fi ller cap , be vel gear 3 Be vel gear 4 Cutting attachment guard 5 Shaft 6 Loop handle 7 Throttle control 8 Stop s witch 9 Throttle lock 10 Cylinder cov er 11 Star ter handle 12 Fuel tank 13 Choke control 14 Air purge 15 Air fi lter cov er 16 Handle adjustment 17 Shaft couplin[...]

  • Page 6

    6 – English GENERAL SAFETY PRECA UTIONS Impor tant P ersonal pr otective equipment HEARING PR O TECTION W ear hearing protection that provides adequate noise reduction. EYE PRO TECTION Alwa ys wear approved e ye protection. If you use a visor then you m ust also wear approv ed protective goggles. Approved protective goggles m ust comply with stan[...]

  • Page 7

    English – 7 GENERAL SAFETY PRECA UTIONS FIRST AID KIT Alw a ys hav e a fi rst aid kit nearby . Mac hine ′′ ′ ′ s safety equipment This section descr ibes the machine ′ s saf ety equipment, its pur pose, and ho w checks and maintenance should be carried out to ensure that it operates correctly . See the ”What is what?” section to lo[...]

  • Page 8

    8 – English GENERAL SAFETY PRECA UTIONS Cutting attachment guar d This guard is intended to pre vent loose objects from being thrown to wards the operator . The guard also protects the operator from accidental contact with the cutting attachment. Check that the guard is undamaged and not cr ack ed. Replace the guard if it has been e xposed to imp[...]

  • Page 9

    English – 9 GENERAL SAFETY PRECA UTIONS If the muf fl er on y our machine is fi tted with a spark arrestor mesh this must be cleaned regularly . A block ed mesh will cause the engine to ov erheat and ma y lead to serious damage. Loc king nut A locking n ut is used to secure some types of cutting attachment. When fi tting, tighten the nut in th[...]

  • Page 10

    10 – English ASSEMBL Y Fitting the loop handle (325Cx) • P osition the handle on the shaft. Note that the handle must be mounted below the arro w on the shaft. • Fit the screw , secur ing plate and wing nut as shown in the diagram. • Tighten the wing nut. Fitting the loop handle (323L, 323LD, 325Lx, 325LDx) • Clip the loop handle onto the[...]

  • Page 11

    English – 11 ASSEMBL Y Fitting the trimmer head Fitting a trimmer guar d and Superauto II 1” trimmer head (323L, 323LD, 325Lx, 325LDx) • Fit the correct trimmer guard (A) for use with the trimmer head. Hook the guard onto the fi tting on the shaft and secure it with the bolt (L). • Fit the drive disc (B) on the output shaft. • T ur n the[...]

  • Page 12

    12 – English ASSEMBL Y Fitting the trimmer guar d and trimmer head (325Cx) Guar d • Fit the guard as shown in the diagr am. Tighten securely . T rimmer head • Fit the dust cup on the shaft. The nut must be completely cov ered by the dust cup . • Hold the dust cup with a spanner to pre vent the shaft from rotating. • Screw the trimmer head[...]

  • Page 13

    English – 13 FUEL HANDLING Fuel safety Ne ver start the machine: 1 If you ha v e spilt fuel on it. Wipe off the spillage and allo w remaining fuel to e vapor ate. 2 If you ha v e spilt fuel on yourself or y our clothes, change your clothes . W ash any part of your body that has come in contact with fuel. Use soap and water . 3 If the machine is l[...]

  • Page 14

    14 – English FUEL HANDLING Mixing • Alwa ys mix the petrol and oil in a clean container intended f or fuel. • Alwa ys star t b y fi lling half the amount of the petrol to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of petrol. • Mix (shake) the fuel mixture thoroughly bef ore fi lling [...]

  • Page 15

    English – 15 ST AR TING AND ST OPPING Chec k bef ore star ting • Check the b lade to ensure that no crac ks hav e formed at the bottom of the teeth or by the centre hole . The most common reason wh y cracks are f or med is that shar p corners have been f or med at the bottom of the teeth while shar pening or that the blade has been used with du[...]

  • Page 16

    16 – English ST AR TING AND ST OPPING CA UTION! Do not pull the star ter cord all the wa y out and do not let go of the star ter handle when the cord is fully extended. This can damage the machine. CA UTION! Do not put any part of your body in marked area. Contact can result in burns to the skin, or electrical shock if the spark plug cap has been[...]

  • Page 17

    English – 17 W ORKING TECHNIQ UES General w orking instructions Basic safety rules 1 Look around you: • T o ensure that people, animals or other things cannot aff ect your control of the machine . • T o ensure that people, animals, etc., do not come into contact with the cutting attachment or loose objects that are thrown out b y the cutting [...]

  • Page 18

    18 – English W ORKING TECHNIQ UES Grass trimming with a trimmer head T rimming • Hold the trimmer head just above the g round at an angle. It is the end of the cord that does the work. Let the cord work at its own pace. Nev er press the cord into the area to be cut. • The cord can easily remov e grass and w eeds up against walls , fences , tr[...]

  • Page 19

    English – 19 MAINTENANCE Carb urettor Y our Husqvarna product has been designed and manuf actured to speci fi cations that reduce harmful emissions. After the engine has used 8-10 tanks of fuel the engine will be run-in. T o ensure that it continues to run at peak perf or mance and to minimise harmful exhaust emissions after the running-in per i[...]

  • Page 20

    20 – English MAINTENANCE Fine adjustment of the idle speed T Adjust the idle speed using the idle adjustment screw T , if it is necessar y to readjust. First tur n the idle adjustment screw T clockwise until the cutting attachment starts to rotate. Then turn the screw anticlockwise until the cutting attachment stops. The idle speed is correctly a[...]

  • Page 21

    English – 21 MAINTENANCE Cooling system T o keep the working temperature as low as possib le the machine is equipped with a cooling system. The cooling system consists of: 1 Air intake on the starter . 2 Fins on the fl ywheel. 3 Cooling fi ns on the cylinder . 4 Cylinder cov er (directs cold air ov er the cylinder). Clean the cooling system wit[...]

  • Page 22

    22 – English MAINTENANCE Oiling the air fi lter Alw a ys use HUSQV ARNA fi lter oil, ar t. no . 531 00 92-48. The fi lter oil contains a solvent to mak e it spread ev enly through the fi lter . Y ou should therefore a v oid skin contact. Put the fi lter in a plastic bag and pour the fi lter oil ov er it. Knead the plastic bag to distribute [...]

  • Page 23

    English – 23 MAINTENANCE Maintenance sc hedule The f ollowing is a list of the maintenance that must be perf or med on the machine. Most of the items are described in the Maintenance section. The user must only carry out the maintenance and ser vice work descr ibed in this Operator’ s Manual. More e xtensive w ork must be carried out by an auth[...]

  • Page 24

    24 – English TECHNICAL D A T A T echnical data Note 1: Noise emissions in the environment measured as sound power (L W A ) in conf ormity with EC directive 2000/14/EC . Note 2: Equivalent sound pressure le vel is calculated as the time-w eighted energy total f or sound pressure lev els under various working conditions with the follo wing time dis[...]

  • Page 25

    English – 25 TECHNICAL D A T A Note 1: Noise emissions in the environment measured as sound power (L W A ) in conf ormity with EC directive 2000/14/EC . Note 2: Equivalent sound pressure le vel is calculated as the time-w eighted energy total f or sound pressure lev els under various working conditions with the follo wing time distribution: 1/2 i[...]

  • Page 26

    26 – English TECHNICAL D A T A EC-dec laration of conformity (Applies to Eur ope only) W e, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare that the clearing saws Husqvarna 323L, 323LD , 325Cx, 325Lx and 325LDx with serial numbers dating from 2002 onwards (the y ear is clearly stated on the rating plate, f ollowed b y the s[...]

  • Page 27

    1 Super Auto II Super Auto II 1 2 3 4 5 6 7 8 9 10 4,0 m 13' 2,4 mm .095" ~2,0 m 6,5 ' 6 " 6 " " 15 cm 15 cm[...]

  • Page 28

    [...]

  • Page 29

    "Clic" 1 2 3 5 6 7 10 11 8,5 m 28' 4 8 4,2 m 14' 2,4-2,7 mm .095-.106" 10 cm 4" 6" 15 cm S35[...]

  • Page 30

    1 2 4 3 2,4-2,7 mm .095-.106" 4,25 m 14' 4,25 m 14' B 6" 15 cm A 6" 15 cm S35 5[...]

  • Page 31

    T35 "Clic" 1 2 3 5 6 7 9 8,5 m 28' 4 8 4,3 m 14' 2,4-2,7 mm .095-.106" 10 cm 4" 6" 15 cm[...]

  • Page 32

    "Clic" 1 2 3 5 6 7 9 6,0 m 18' 4 8 3,05 m 9' 2,0-2,4 mm .079-.095" 10 cm 4" 6" 15 cm T25[...]

  • Page 33

    2 4 3 2,0-2,4 mm .079-0.095" 2,75 m 9' 2,75 m 9' 6" 15 cm 5 6 1 T25C[...]

  • Page 34

    ´®z+R-T¶63¨ ´®z+R-T¶63¨ "Clic" 1 2 3 5 6 7 9 2,75 m x 2 9' x 2 4 8 2,0-2,4 mm .079-0.095" 2,75 m 9' 2,75 m 9' 6" 15 cm T25C[...]

  • Page 35

    [...]

  • Page 36

    ´®z+R-T¶63¨ 2005-10-25 ´®z+R-T¶63¨ 1150135-26[...]