Husqvarna 326RX manual

114 00 18-93 326R X-SERIES Operator's Manual (CARB II, EP A II) Read through the Operator's Manual carefully and understand the content before using the machine.[...]

2 – English Symbols SYMBOL EXPLANA TION W ARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can r esult in serious or fatal injury to the operator or others. Read through the O perator‘ s Manual carefully and understand the content before using the machine. • Use anti-slip and stable boots. • Alway[...]

English – 3 CONTENTS List of contents SYMBOL EXPLANA TION Symbols ............................................................................... 2 CONTENTS List of contents .................................................................... 3 SAFETY INSTRUCTIONS P ersonal pr otective equipment ............................................. 4 The[...]

4 – English The machine‘s safety equipment This section describes the machine ‘ s safety equipment, its function and how checks and maintenance ar e carried out to ensure that it operates correctly . (See the chapter “What is what“ to locate where this equipment is positioned on your machine.) Personal protective equipment SAFETY INSTR UC[...]

English – 5 2. Stop switch The stop switch should be used to stop the engine. 3. Cutting attachment guard This guard is intended to prevent objects from being thrown to wards the operator and to protect the operator from unintentionel contact with the cutting attachment. 4. Anti-vibration system Y our machine is equipped with an anti-vibration sy[...]

6 – English SAFETY INSTR UCTIONS 6. Muffler The muffler is designed to give the lowest possible noise level and to direct the engine ‘ s exhaust fumes away from the operator . Muffler fitted with catalytic converter is also designed to reduce harmful exhaust components. In countries that have a warm and dry climate the risk of fire is obvious. [...]

English – 7 SAFETY INSTR UCTIONS 1. Throttle trigger lock • Check that the throttle is locked in the “ idling position “ when the throttle trigger lock is in its original position. • Press in the throttle trigger lock and make sure it returns to its original position when released. • Ensure that the throttle and throttle trigger lock mo[...]

8 – English SAFETY INSTR UCTIONS 3. Cutting attachment guard • Check that the guard is undamaged and not cracked. • Replace the guard if it has been exposed to impact or is cracked. • Always use the prescribed blade an guard combination, see chapter "Technical data" . 5. Muffler 1. Never use a machine that has a defective muffler.[...]

English – 9 7. Quick-release • Check that the harness straps are correctly positioned. When the harness and machine are adjusted, check the harness ‘ safety release catch to ensure it works correctly. SAFETY INSTR UCTIONS 6. Cutting equipment This section describes how through corr ect maintenance and through using the right type of cutting e[...]

10 – English SAFETY INSTR UCTIONS Cutting equipment Sharpening the grass blade • See the cutting equipment ’ s packaging for correct filing instructions. • The blades are sharpened using a single cut flat file. • Sharpen all edges equally to maintain the balance of the blade. Trimmer head • Only use a trimmer head and trimmer cord that [...]

English – 11 SAFETY INSTR UCTIONS General safety instructions IMPORT ANT INFORMA TION • This machine is intended solely for trimming and clearing grass and for light brush-cutting. • The only accessories to be used with the engine unit as a drive source are the cutting units we recommend in the chapter “ T echnical data “ . • Never use [...]

12 – English General working instructions SAFETY INSTR UCTIONS Basic safety precautions 1. Observe your surroundings: • To ensure that people, animals or other things cannot affect your control of the machine. • To ensure that the above mentioned do not come into contact with the cutting equipment or objects that can be thrown by the cutting [...]

English – 13 SAFETY INSTR UCTIONS Adjusting the harness and clearing saw Designations • Use a saw blade for cutting woody growth with thin stems. • Use a grass knife or grass blade for clearing grass. • Use a trimmer head or plastic blades for lighter clearing work, for example along verges or around trees. Basic clearing techniques • Alw[...]

14 – English SAFETY INSTR UCTIONS Clearing ‘ s ABC A. Always use the correct equipment. B. Always have well adjusted equipment. C. Follow the safety instructions. D. Organise the work well. E. Always use full throttle when applying the blade. F. Always use a sharp blade. G. Avoid stones. ! W ARNING! A v oid cutting in the cutting region between[...]

English – 15 SAFETY INSTR UCTIONS Grass clearing using the trimmer head and plastic blades. • Hold the trimmer head just above the ground at an angle. It is the end of the cord that carries out the work. Let the cord work at its own pace. Do not press the cord into the area to be cut. • The cord can easily remove grass and weeds up against wa[...]

16 – English WHA T IS WHA T? What is what on the brushcutter? 1. Blade 2. Gr ease filler cap 3. Angle gear 4. Combination guard 5. Shaft 6. Handlebars 7. Throttle 8. Stop switch 9. Throttle trigger lock 10. Hanging ring 11. C ylinder cover 12. S tar ter handle 13. F uel tank 14. Choke 15. Air purge 16. Air filter co ver 17. Clutch co ver 18. Hand[...]

English – 17 ASSEMBL Y Assembling the handlebars • Remove the screw at the rear of the throttle handle. • Slide on the throttle handle on the right-hand side of the handlebars, (see the diagram). • Align the hole in the throttle handle for the fixing screw with the hole on the handlebars. • Refit the screw in the rear of the throttle hand[...]

18 – English ASSEMBL Y Assembly of the blade and trimmer head Assembling the blade guard and clearing blade • Remove the mounting plate (H). Fit the adapter (I) and bracket (J) with the two screws (K) as shown. Fit the blade guard (A) to the adapter using the 4 screws (L) as shown. NOTE! Use the recommended blade guard. “ See Technical data ?[...]

English – 19 ASSEMBL Y Assembling the spray guard and trimmer head Superauto II • Fit the appropriate guard (A) for use with the trimmer head. Hook the guard onto the shaft fitting and secure it with the bolt (L). • Fit the disc drive (B) on the output axle. • Turn the blade axle until one of the disc drive ’ s holes aligns with the corre[...]

20 – English ASSEMBL Y Adjusting the harness and clearing saw Quick release On the front is an easily accessible, quick release catch. U se this if the engine should catch fire or in any other emergency situation when you quickly need to take off the harness and machine. Even load on the shoulders A well-adjusted harness and clearing saw signific[...]

English – 21 FUEL HANDLING Fuel mixture • Clean around the fuel cap. Contamination in the tank can disrupt operations. • Ensure that the fuel is well mixed by shaking the container before filling the tank. W ARNING! Always provide good ventilation when handling fuel. ! Fuelling W ARNING! The following precautions reduce the risk of fire: Do n[...]

22 – English ST AR T AND ST OP Control before starting Cold engine IGNITION: Set the stop switch to the start position. CHOKE: Set the choke control in the choke position. AIR PUR GE: P ress the air purge diaphragm repeatedly until fuel begins to fill the diaphragm. The diaphragm need not be completely filled. Warm engine U se the same starting p[...]

English – 23 Carburetor Y our Husqvarna pr oduct has been designed and manufactured to specifications that r educe harmful emissions. After your unit has been run 8-10 tanks of fuel the engine has broken in. T o ensure that y our unit is at peak performance and producing the least amount of harmful emissions after br eak in, have your authorized [...]

24 – English Final setting of the idling speed T Adjust the idling speed with the screw T , If it is necessar y to readjust. F irst turn the idle speed adjusting screw T clockwise until the cutting attachment starts to rotate/ mo ve. Then turn, counter- clockwise until the cutting attachment stops. A correctly adjusted idle speed setting occurs w[...]

English – 25 MAINTENANCE Cooling system T o maintain as low opera- ting temperature as possible the engine is equipped with a cooling system. The cooling system consists of: 1. An air intake on the starter unit. 2. Cooling fins on the flywheel. 3. Cooling fins on the cylinder 4. Cylinder cover (leads cold air onto the cylinder). Clean the cooling[...]

26 – English Spark plug The condition of the spark plug is affected by: • An incorrect carburetor setting. • An incorrect fuel mixture (too much or faulty oil). • A dirty air filter. These factors cause deposits on the spark plug electrode that may result in malfunction or starting difficulties. If the machine is low on po wer , difficult t[...]

English – 27 MAINTENANCE NOTE : Use only HUSQ V ARNA replacement parts. Use of other brands of replacement parts can cause damage to your unit or injur y to the operator or others. Y our warranty does not cover damage or liability caused b y the use of accessories and/or attachments not specifically recommended by HUSQV ARNA. Maintenance schedule[...]

28 – English TECHNICAL D A T A T echnical data Engine Cylinder capacity , cu. in/cm 3 Cylinder bor e, inch/mm Stroke length, inch/mm Idling speed, rpm Recommended max. speed, rpm Speed of output axle, rpm Max. engine output, acc. to ISO 8893. kW/rpm Catalytic converter muffler Speed-r egulated ignition system Ignition system Manufacturer/type of [...]

English – 29 Repair or replacement of any warranted part will be performed at no charge to the owner at an approved Husqvarna Forest & Garden servicing dealer. If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized servicing dealer or call Husqvarna Forest & Garden at 1-80[...]

30 – English 1 Super Auto II Super Auto II 1 2 3 4 5 6 7 8 9 10 4,0 m 13' 2,4 mm .095" ~2,0 m 6,5 ' 6 " 6 " " 15 cm 15 cm[...]

English – 31 1 T ri Cut 2 3 4 5 6 7 8 >20mm >20mm ! B A 6 Nm X 10[...]

32 – English 1 T rimmy H II 2 3 4 5 6 7 8 9 7,5 m 25' 2,0-2,4 mm .080-.095" 1 2 15 cm 6" ~ 3,7 m 12' 15 cm 6"[...]

English – 33 1 T rimmy Hit 23 4 5 6 7 8 9 10 11 “ Click ” “ Click ” 7,0 m 23' " 12 cm 5" ~ 3,5 m 1 1' 15 cm 6 " " 2,0-2,4 mm .080-.095 ~ 15 cm 6[...]

34 – English 1 T rimmy Hit Junior 2 5 6 7 8 9 10 12 “ Click ” 3 4 5,75 m 19' 2,0-2,4 mm .080-.095" 15 cm 6" ~ 2,8 m 9' 1.) 2.) 11 15 cm 6" 15 cm 6"[...]

English – 35 1 T rimmy Hit Pro 2 5 6 7 8 9 10 12 “ Click ” 3 4 7,5 m 25' 2,0-2,4 mm .080-.095" 15 cm 6" ~ 3,7 m 12' 1.) 2.) 11 15 cm 6" 15 cm 6"[...]

36 – English 1 T rimmy Hit VI 2 5 6 3 4 7 8 9 10 11 “ Click ” 7,0 m 23' " 12 cm 5" ~ 3,5 m 1 1' 15 cm 6 " " 2,0-2,4 mm .080-.095 ~ 15 cm 6[...]

English – 37 1 2 3 4 5 6 7 8 9 35-50 NM ~ 15 cm 6' "Clic" ~ 3,5 m 11 ' 7,0 m 23' 2,4-3,3 mm .095"-.130" 12 cm 5" T rimmy SII[...]

38 – English ´+H!y¶3D¨ ~ 15 cm 6' N ~ 15 cm 6' 502 25 56-01 502 26 04-01 502 25 53-01 502 26 24-01 (x2) 740 43 14-00 502 25 52-01 502 26 01-01 735 31 19-00 729 53 27-71 (x3) 738 21 03-04 502 26 03-01 502 27 07-01 502 26 86-01 1 23 4 T rimmy SII[...]

English – 39[...]

2001W22 ´+H!y¶3D¨[...]