Integra DTR-5.6 manual

DTR-5.6 Instr uction Manual AV Receiv er DTR-5.6.book Page 1 Thursday, September 22, 2005 5:07 PM[...]

2 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follo w all instructions. 5. Do not use this apparatus near water . 6. Clean only with dry cloth. 7. Do not block any v entilation openings. Install in accordance with the manufacturer’ s instructions. 8. Do not install near an y heat [...]

3 Precautions 1. Recording Copyright —Unless it’ s for personal use only , recording copyrighted material is illegal with- out the permission of the copyright holder . 2. A C Fuse —The A C fuse inside the unit is not user - serviceable. If you cannot turn on the unit, contact the dealer from whom you purchased this unit. 3. Care —Occasional[...]

4 Thank you for purchasing an Integra A V Receiv er . Please read this manual thoroughly before making con- nections and plugging in the unit. Follo wing the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your ne w A V Receiv er . Please retain this manual for future reference. Supplied Access[...]

5 Contents Introduction Important Safety Instructions .................... 2 Precautions ................................................. 3 Supplied Accessories ................................. 4 Features ....................................................... 6 Before Using the AV receiver ....................7 Getting to Know the AV Receiver ..[...]

6 Features Amplifier • 90 watts per channel into 8 ohms, 20 Hz to 20 kHz, less than 0.08% total harmonic distortion (FTC rating) • 7-channel amplifier • Optimum Gain V olume Circuitry • WRA T (W ide Range Amplifier T echnology) • Massiv e High Current Power Supply (H.C.P .S.) trans- former • Color-coded speak er terminal posts • VL[...]

7 Bef ore Using the A V receiver Notes: • If the remote controller doesn’t w ork reliably , try replacing the batteries. • Don’t mix ne w and old batteries or different types of batteries. • If you intend not to use the remote controller for a long time, remov e the batteries to prev ent damage from leakage or corrosion. • Expired batte[...]

8 Getting to Kno w the A V Receiver For detailed information, see the pages in parentheses. A Standby/On b utton (36) Sets the A V receiver to On or Standby . B Standby indicator (36) Lights up when the A V receiver is on Standby and flashes while a signal is being receiv ed from the remote controller . C Zone 2 indicator (75) Lights up when Zone [...]

9 Getting to Know the A V Receiver —Continued T Input selector buttons (44) Select the following input sources: Multi CH, D VD, V ideo 1, V ideo 2, V ideo 3, V ideo 4, T ape, T uner , or CD. The [Multi CH] button selects the multichannel D VD input. U Setup Mic (37) The automatic speaker setup microphone connects here. V Video 4 Input (30, 57) Us[...]

10 Getting to Know the A V Receiver —Continued A OPTICAL DIGIT AL These optical digital audio inputs are for connecting components with optical digital audio outputs, such as CD players and D VD players. The optical digital audio output is for connecting a digital recorder with an optical digital input, such as a CD recorder . B CO AXIAL DIGIT AL[...]

11 Getting to Know the A V Receiver —Continued O CD IN This analog audio input is for connecting a CD player’ s analog audio output. P T APE IN/OUT This analog audio input and output are for connect- ing a recorder with an analog audio input and out- put, such as a cassette deck, MD recorder , etc. Q VIDEO 3 IN A VCR for playback only , or a ca[...]

12 Remote Contr oller Including the A V receiver, the remote controller can be used to control up to nine different components. The remote controller has a specific operating mode for use with each type of component. Modes are selected by using the eight Remote Mode buttons. ■ Receiver/T ape Mode In Receiv er/T ape mode, you can control the A V [...]

13 Remote Controller —Continued For detailed information, see the pages in parentheses. A Standby b utton (36) Sets the A V receiver to Standby . B On button (36) T urns on the A V receiv er. C Input Selector buttons (44) Used to select the input sources. D Multi CH button (51) Selects the multichannel D VD input. E Dimmer button (52) Adjusts the[...]

14 Remote Controller —Continued To set the remote controller to D VD mode, pr ess the [D VD] Remote Mode button. A Standby b utton Sets the D VD player to Standby . B On button T urns on the D VD player . C Number buttons Used to enter title, chapter , and track numbers, and to enter times for locating specific points. D T op Menu button Selects[...]

15 Remote Controller —Continued To control an Integra CD player or a CD/MD recorder made by another manufactur er , press the [CD] Remote Mode button to select the CD r emote controller mode. To control an Integra MD recorder or CD r ecorder , press the [MD] or [CDR] Remote Mode b utton to select the MD or CDR remote contr oller mode. In order to[...]

16 Remote Controller —Continued HDD mode is for controlling Integra’ s next generation HDD-compatible components. As of 2005, it can be used with the Onkyo DS-A1 Remote Interacti ve Dock and Apple iPod connected via . When Using the Onky o DS-A1: • Connect the DS-A1 to the T APE IN or VIDEO 3 IN jacks. • Set the DS-A1’ s RI MODE switch to[...]

17 Connecting Y our Speakers Thanks to the A V receiver’ s superb capabilities, you can enjoy surround sound with a real sense of mov ement in your own home—just lik e being in a movie theater or concert hall. Y ou can enjoy D VDs featuring DTS and Dolby Digital. W ith analog and digital TV , you can enjoy Dolby Pro Logic IIx and Onkyo’ s own[...]

18 Connecting Y our Speakers —Continued Speaker Configuration F or the best surround-sound e xperience, you should con- nect sev en speakers and a po wered subwoofer . The following table sho ws which channels you should use based on the number of speakers you ha ve. *If you’re using only one surround back speaker, connect it to the left (L) S[...]

19 Connecting Y our Speakers —Continued Speaker Connection Precautions Read the following before connecting your speak ers: • American model only: Only connect speakers with an impedance of 6 ohms or higher . If you use speakers with a lower impedance, and use the amplifier at high volume le vels for a long period of time, the b uilt-in protec[...]

20 Connecting Antenna This section explains ho w to connect the supplied indoor FM antenna and AM loop antenna, and ho w to connect commercially av ailable outdoor FM and AM antennas. The A V receiver w on’t pick up any radio signals without any antenna connected, so you must connect the antenna to use the tuner . The supplied indoor FM antenna i[...]

21 Connecting Antenna —Continued If you cannot achiev e good reception with the supplied indoor FM antenna, try a commercially av ailable out- door FM antenna instead. Notes: • Outdoor FM antennas work best outside, b ut usable results can sometimes be obtained when installed in an attic or loft. •F or best results, install the outdoor FM ant[...]

22 Connecting Y our Components • Before making any A V connections, read the manuals supplied with your other A V components. • Don’t connect the po wer cord until you’ ve completed and double-checked all A V connections. Optical Digital Jacks The A V receiver’ s optical digital jacks have shutter -type cov ers that open when an optical p[...]

23 Connecting Y our Components —Continued By connecting both the audio and video outputs of your D VD player and other A V components to the A V receiver, you can switch the audio and video signals simultaneously simply by changing the input source on the A V receiver. The A V receiver supports se veral connection formats for compatibility with a[...]

24 Connecting Y our Components —Continued •W ith connection , you can listen to and record audio from your TV and listen in Zone 2. •T o enjo y Dolby Digital and DTS, use connection or . (For Zone 2, use and , or and .) Hint! If your TV has no audio outputs, connect an audio output from your VCR to the A V receiver and use its tuner to lis- t[...]

25 Connecting Y our Components —Continued •W ith connection , you can listen to and record audio from a DVD and listen in Zone 2. •T o enjo y Dolby Digital and DTS, use connection or . (For Zone 2, use and , or and .) • If your D VD player has main left and right outputs and multichannel left and right outputs, be sure to use the main left [...]

26 Connecting Y our Components —Continued Hooking Up the Multichannel D VD Input If your D VD player supports multichannel audio formats such as D VD-Audio or SA CD, and it has a multichannel analog audio output, you can connect it to the A V receiver’ s multichannel D VD input. Use a multichannel analog audio cable, or sev eral normal audio ca[...]

27 Connecting Y our Components —Continued In addition to video playback, with this hookup, you can use your VCR’ s tuner to listen to your favorite TV programs via the A V receiver, useful if your TV has no audio outputs. If you hav e two video recorders (e.g., a VCR and a D VD recorder), connect one recorder to the VIDEO 1 IN jacks, as shown h[...]

28 Connecting Y our Components —Continued If you hav e two video recorders (e.g., a VCR and a D VD recorder), connect one recorder to the VIDEO 1 OUT jacks, as shown here, and connect the other recorder to the VIDEO 2 OUT jacks in the same way . Connecting a VCR or DVD Recor der f or Recording Connection A V receiver Signal flow VCR or D VD reco[...]

29 Connecting Y our Components —Continued •W ith connection , you can listen to and record audio from the video source and listen in Zone 2. •T o enjo y Dolby Digital and DTS, use connection or . (For Zone 2, use and , or and .) Connecting a Satellite, Cable, Set-top bo x, or Other Video Source Connection A V receiver Signal flow Video sourc[...]

30 Connecting Y our Components —Continued Connecting a Camcorder , Games Console, or Other Device Connection A V receiver Signal flow Camcorder or console Video 4 Input S Video ⇐ S-Video output Video 4 Input Video ⇐ Composite video output Video 4 Input L/R ⇐ Analog audio L/R output Video 4 Input Digital ⇐ Digital optical output Step 1: V[...]

31 Connecting Y our Components —Continued •W ith connection , you can listen to and record audio from the CD player and listen in Zone 2. •T o connect the CD player digitally , use connection or . (For Zone 2, use and , or and .) Connecting a CD Play er Connection A V receiver Signal flow CD player CD IN L/R ⇐ Analog audio L/R output DIGIT[...]

32 Connecting Y our Components —Continued ■ T urntable with a Built-in Phono Preamp Use an analog audio cable to connect an unused audio input on the A V receiver to the audio outputs on your turntable, as shown. ■ T urntable without a Built-in Phono Preamp Use an analog audio cable to connect an unused audio input on the A V receiver to the [...]

33 Connecting Y our Components —Continued •W ith connection , you can play and record and listen in Zone 2. •T o connect the recorder digitally for playback, use connections and , or and . •T o connect the recorder digitally for recording, use connection . If you want to use a more po werful power amplifier and use the A V receiver as a pr[...]

34 Connecting Y our Components —Continued W ith (Remote Interactiv e), you can use the following special functions: Auto P o wer On/Standby When you start playback on a component connected via , if the A V receiver is on Standby , it will automatically turn on and select that component as the input source. Similarly , when the A V receiv er is se[...]

35 Connecting Y our Components —Continued The A V receiver has A C outlets on its rear panel that can be used to connect the power cords of other components that you intend to use with the A V receiver. These com- ponents can then be left turned on so that they turn on and off as and when the A V recei ver is turned on and set to Standby . Cautio[...]

36 T urning On the A V Receiver Standby/On On Receiver Standby Standby indicator T urning On and Standby Press the [Standby/On] b utton. Alternatively , press the remote contr oller’ s [Receiver] b utton, followed b y the [On] button. The A V receiver comes on, the display lights up, and the Standby indicator goes of f. Pressing the remote contro[...]

37 Fir st Time Setup This section explains the settings that you need to make before using the A V receiver for the v ery first time. W ith the supplied speaker setup microphone, the Auto- matic Speaker Setup function can measure the test tone output by each speaker and automatically determine the number of speakers connected, the crossov er frequ[...]

38 First Time Setup —Continued Tip: •Y ou can cancel the automatic speaker setup at anytime by disconnecting the microphone. 3 Press [Enter]. The automatic speaker setup starts. The test tone is output by each speaker in turn. The microphone picks up the sound and feeds it back to the A V receiv er, where it’ s used to calculate the optimum s[...]

39 First Time Setup —Continued ■ Checking the Results If you selected “Check the Results” in step 4 on the pre- vious page, the following menu appears and you can check the results of the automatic speaker setup. 1. W arning— Undetected speakers and position warn- ings (see the right column). 2. Speaker Config— Connected speakers and c[...]

40 First Time Setup —Continued If you connect a video component to COMPONENT VIDEO IN 1, 2, or 3, you must assign that input to an input selector . F or example, if you connect your D VD player to COMPONENT IN 3, you must assign COM- PONENT IN 3 to the D VD input selector . To upcon vert and output composite video and S-V ideo sources from the CO[...]

41 First Time Setup —Continued If you connect a component to a digital input, you must assign that input to an input selector . F or example, if you connect your CD player to OPTICAL IN 2, you must assign OPTICAL IN 2 to the CD input selector . Here are the default assignments. * The front panel optical DIGIT AL input. Note: • This procedure ca[...]

42 First Time Setup —Continued If you connect an -capable Integra MiniDisc recorder , CD recorder , or next generation HDD-compat- ible component to the T APE IN/OUT or VIDEO 3 IN jacks, for to work properly , you must change this setting. This setting can only be changed on the A V receiver. Note: HDD can be selected for the T ape input selector[...]

43 First Time Setup —Continued Y ou must specify the TV system used in your area. Note: • This procedure can also be performed on the A V receiv er by using its [Setup] button, arro w buttons, and [Enter] button. Y ou must specify the AM frequency step used in your area. Note that when this setting is changed, all radio presets are deleted. Not[...]

44 Pla ying Y our A V Components Basic A V Receiver Operation 3 1 3 1 1 1 Use the A V receiver’ s input selector b uttons to select the input source. To select the input source with the remote controller , press the [Receiver] Remote Mode button, and then use the Input Selector b uttons. On the remote controller , the [V1], [V2], [V3], and [V4] b[...]

45 Listening to the Radio W ith the built-in tuner , you can enjoy AM and FM radio stations, and store your fa vorite stations as presets for easy selection. T uning into AM/FM Radio Stations ■ A uto T uning Mode When tuned into a station, the TUNED indicator appears. When tuned into a stereo FM station, the FM STEREO indicator also appears. ■ [...]

46 Listening to the Radio —Continued Note: Hardware and required basic monthly subscription sold separately . Premium Channels available at additional monthly cost. Installation costs and other fees and taxes, including a one-time activ ation fee may apply . Subscrip- tion fee is consumer only . All fees and programming subject to change. Channel[...]

47 Listening to the Radio —Continued Selecting XM Radio Channels There are two modes for selecting XM radio channels: Channel Search mode , which allows you to select an y channel. Category Search mode , which allows you to select channels by category . ■ Channel Searc h Mode Note: Channels cannot be selected while the indicator is flashing, a[...]

48 Listening to the Radio —Continued Selecting XM Channels from the Fr ont Panel: Displaying XM Radio Inf ormation The following information can be displayed: Note: If the category , artist, or song title is not av ailable, “- - -” will be displayed instead. ■ Displaying XM Inf ormation on Y our TV When you select a different XM channel, or[...]

49 Listening to the Radio —Continued P ositioning the XM Antenna Y ou can check the signal strength of the XM radio signal and adjust the position of the XM antenna accordingly . Note: If the signal quality is 0%, make sure that the XM antenna is connected properly . XM Radio Messages The following messages may appear while using XM radio. The XM[...]

50 Listening to the Radio —Continued Y ou can store a combination of up to 40 of your fav orite AM/FM radio stations and XM channels as presets. Selecting Presets Deleting Presets Presetting AM/FM Stations and XM Channels 1 T une into the AM/FM station or XM channel that y ou want to store as a preset. 2 Press the [Memory] button. The MEMOR Y ind[...]

51 Using the Multichannel D VD Input The multichannel D VD input is for connecting a compo- nent with a 5.1/7.1-channel analog audio output, such as a D VD player , D VD-Audio/SA CD-capable player , or an MPEG decoder . See page 26 for hookup information. Note: • While the multichannel D VD input is selected, the Speaker Configuration settings o[...]

52 Common Functions This section explains functions that can be used with an y input source. Y ou can adjust the brightness of the display . Y ou can adjust the volume of each speaker while listen- ing to an input source. These temporary adjustments are cancelled when the A V receiver is set to Standby . Notes: •Y ou cannot use this function whil[...]

53 Common Functions —Continued W ith the sleep timer , you can set the A V receiver so that it turns off automatically after a specified period. To cancel the sleep timer , press the [Sleep] button repeatedly until the SLEEP indicator disappears. To check the remaining sleep time, press the [Sleep] b utton. Note that if you press the [Sleep] b u[...]

54 Using the Listening Modes F or a description of each listening mode, see “ About the Listening Modes” on page 56. Selecting on the A V Receiver ■ [Stereo] button This button selects the Stereo listening mode. ■ Listening Mode [ ]/[ ] buttons Pressing these buttons repeatedly c ycles through all of the listening modes that can be used wit[...]

55 Using the Listening Modes —Continued The following table sho ws which listening modes can be used with each input signal format. : Only a vailable on 6.1/7.1-channel playback systems. Not a vailable while the ZONE 2 SPEAKERS terminals are being used. : Only av ailable on 7.1-channel playback systems. Not av ailable while the ZONE 2 SPEAKERS te[...]

56 Using the Listening Modes —Continued The A V receiver’ s listening modes can transform your listening room into a movie theater or concert hall, with high fidelity and stunning surround sound. Direct In this mode, audio from the input source is output directly with minimal processing, providing high-fidel- ity reproduction. All of the sour[...]

57 Recor ding This section explains ho w to record the input source and how to record audio and video from separate sources. Notes: • The surround sound and DSP listening modes cannot be recorded. • Copy-protected D VDs cannot be recorded. • Sources connected to the multichannel D VD input cannot be recorded. •V arious restrictions apply to[...]

58 Onscreen Setup Menus The onscreen setup menus are displayed on the connected TV and pro vide a con venient way to change the A V receiv er’ s settings, which are arranged into two groups: Fi r st T ime Setup and Advanced Setup . To get your system up and running, you must complete the First T ime Setup settings. The Advanced Setup settings are[...]

59 Adjusting the Listening Modes W ith the Cine Filter function, you can correct a soundtrack whose high-frequency content is too harsh, making it more suitable for home theater viewing. This function can be used with the following listening modes: Dolby Digital, Dolby Digital EX, Dolby Pro Logic II Movie, Dolby Pro Logic IIx Mo vie, DTS, DTS- ES, [...]

60 Adjusting the Listening Modes —Continued T one Control Settings Y ou can adjust the bass and treble for the front speakers. The tone control circuits are bypassed in the Direct lis- tening mode. ■ Bass Y ou can boost or cut low-frequenc y sounds output by the front speakers from –10 dB to +10 dB in 1 dB steps. ■ T reble Y ou can boost or[...]

61 Adjusting the Listening Modes —Continued Dolby Digital Settings ■ Dolby EX This setting determines how Dolby Digital EX signals are handled. This setting is una vailable if no surround back speakers are connected or the ZONE 2 SPEAKERS terminals are being used (page 73). A uto: Dolby Digital EX can be selected from among the Dolby listening [...]

62 Adjusting the Listening Modes —Continued Y ou can specify a default listening mode for each signal format supported by each input selector . The A V receiver will then automatically select that listening mode based on the format of the input signal. Y ou can select other listening modes while listening to a source, but the default listening mo[...]

63 Ad v anced Setup This section explains ho w to check the speaker settings and how to set them manually , which is useful if you change a speaker after performing the automatic speaker setup. Some speaker settings are set automatically by the Auto- matic Speaker Setup function (see page 37). Speaker Configuration Here you can specify which speak[...]

64 Adv anced Setup —Continued Crosso ver Note: • If the crossov er frequency is set to a lo w value, and the program material doesn’t contain an y sounds below that frequency , the subwoofer will not output much sound. 6 Use the Up and Down [ ]/[ ] b uttons to select “c. Center , ” and then use the Left and Right [ ]/[ ] buttons to select[...]

65 Adv anced Setup —Continued Subwoof er Mode W ith this setting, you can boost bass output by feeding front left and right channel bass sounds to the subwoofer . This setting can only be made if the Subwoofer setting in step 4 is set to Y es, and the Front setting in step 5 is set to Large. Note: • These procedures can also be performed on the[...]

66 Adv anced Setup —Continued Note: • This procedure can also be performed on the A V receiv er by using its [Setup] button, arro w buttons, and [Enter] button. Speaker Level Calibration W ith these settings, you can adjust the lev el of each speaker while listening to the test tone so that the v olume of each speaker is the same at the listeni[...]

67 Adv anced Setup —Continued Equalizer Settings W ith these settings, you can adjust the tone of each speaker . The volume of each speaker can be set on page 66. Note: • This procedure can also be performed on the A V receiv er by using its [Setup] button, arro w buttons, and [Enter] button. 1 Press the [Receiver] Remote Mode button, f ollowed[...]

68 Adv anced Setup —Continued This section explains items on the “Input Setup” menu. Delay ■ A/V Sync When using progressiv e scanning, you may find that the picture and sound are out of sync. W ith this setting, you can correct this by delaying the audio signals from 0 to 150 milliseconds (ms) in 1 millisecond steps. Note: • This proced[...]

69 Adv anced Setup —Continued This section explains items on the “Preference” menu. Note: • This procedure can also be performed on the A V receiv er by using its [Setup] button, arro w buttons, and [Enter] button. IntelliV olume W ith this preference, you can set the input lev el for each input source. This is useful if some of your compon[...]

70 Adv anced Setup —Continued ■ Po wer On V ol / Z2 Po wer On V ol W ith these preferences, you can specify the volume set- tings to be used in the main room and Zone 2 when the AV receiv er is turned on. When the V olume Display preference is set to Absolute, the range of “Power On V ol” is 0 to 100 (“Z2 Power On V ol” is 0 to 82). Whe[...]

71 Adv anced Setup —Continued Changing the A V Receiver’ s Remote ID When sev eral Integra components are used in the same room, their remote ID codes may ov erlap. T o differenti- ate the A V receiver from the other components, you can change its remote ID from 1, the default, to 2 or 3. Note: If you change the A V receiver’ s remote ID, be [...]

72 Adv anced Setup —Continued Normally , the A V receiv er detects the signal format auto- matically . Howev er , if you experience either of the fol- lowing issues when playing PCM or DTS material, you can specify the signal format as either PCM or DTS: • If the beginnings of tracks from a PCM source are cut off, try the PCM setting. • If no[...]

73 Zone 2 W ith the Zone 2 function, you can enjoy one input source in the main room and a different input source in another room. There ar e two ways to hook up y our Zone 2 speakers: 1) Use another amp (receiv er , integrated amp, or po wer amp) in Zone 2 and connect your Zone 2 speakers to it. 2) Connect your Zone 2 speakers to this A V receiv e[...]

74 Zone 2 —Continued If you’ ve connected your Zone 2 speak ers to this A V receiv er, as explained in “Using Only Speakers in Zone 2” on page 73, you must set the Powered Zone 2 setting to Act (Acti vated) as e xplained here. If you’ ve connected your Zone 2 speak ers to a power amp with no volume control in Zone 2, as e xplained in “U[...]

75 Zone 2 —Continued This section explains ho w to turn Zone 2 on and off, how to select an input source for Zone 2, and how to adjust the volume for Zone 2. Controlling Zone 2 fr om the A V Receiver Controlling Zone 2 with the Remote Controller Note: •T o control Zone 2, you must press the remote control- ler’ s [Zone 2] Remote Mode b utton [...]

76 Zone 2 —Continued Adjusting the V olume for Zone 2 To Mute Zone 2: Press the remote controller’ s [Zone 2] b utton, followed by the [Muting] button. T o unmute Zone 2, press the remote controller’ s [Zone 2] b utton again, followed by the [Muting] button, or adjust the v olume for Zone 2. Notes: • Only analog input sources are output by [...]

77 Zone 2 —Continued When the A V receiver’ s 12 V TRIGGER OUT A/B/C jack is connected to the 12 V trigger input on a con- nected component, you can specify whether or not a 12- volt trigger signal is output when that component is selected as the source for the main room, Zone 2, or either . Hookup • Use a miniplug cable to connect the A V re[...]

78 Zone 2 —Continued To control the A V receiver with the remote controller while you’ re in the Zone 2 room, you’ll need a commer - cially av ailable multiroom remote control kit. • Multiroom kits are made by Niles and Xantech. These kits can also be used when there isn’t a clear line of sight to the A V receiver’ s remote sensor , suc[...]

79 Contr olling Other Components Y ou can control your other components, including those made by other manufacturers, with the remote controller . This section explains ho w to: • Enter the remote control code for a component that you want to control (e.g., D VD, TV , VCR). • Learn commands directly from another component’ s remote controller[...]

80 Controlling Other Components —Continued Remote Control Codes f or Integra Components Connected via Integra components that are connected via are con- trolled by pointing the remote controller at the A V receiv er, not the component. This allo ws you to control components that are out of view , in a rack, for example. If you want to control an [...]

81 Controlling Other Components —Continued To control another component, point the remote contr oller at it and use the buttons explained below . (Y ou must select the appropriate r emote control mode first.) With some A V components, certain buttons may not work as expected, and some may not work at all. ■ Controlling a TV A [On], [Standby], [...]

82 Controlling Other Components —Continued The A V receiver’ s remote controller can receiv e and learn commands from other remote controllers. By trans- mitting, for example, the Play command from your CD player’ s remote controller , the remote controller can learn it and then transmit the exact same command when its Play [ ] button is pres[...]

83 Controlling Other Components —Continued Y ou can program the remote controller’ s Macro buttons to perform a sequence of actions. Example: To play a CD, you typically need to perform the follow- ing actions: 1. Press the [Receiv er] Remote Mode button to select the Receiv er remote controller mode. 2. Press the [On] button to turn on the A V[...]

84 Tr oubleshooting If you hav e any trouble using the A V receiv er, look for a solution in this section. If you can’t resolv e the issue yourself, contact the dealer from whom you purchased. Can’t turn on the A V receiver • Make sure that the po wer cord is plugged into the wall outlet properly . • Unplug the power cord from the w all out[...]

85 Tr oubleshooting —Continued The Zone 2 speakers pr oduce no sound • The Zone 2 speakers only output sources that are con- nected to an analog input. Check to see if the source is connected to an analog input. There’ s no sound with a certain signal format • Check the digital audio output setting on the con- nected device. On some g ames [...]

86 Tr oubleshooting —Continued The remote controller doesn’t w ork • Make sure that the batteries are installed with the cor - rect polarity (page 7). • Make sure that the remote controller is not too far aw ay from the A V receiver, and that there’ s no obstruction between the remote controller and the A V receiv er’ s remote control s[...]

87 Specification Amplifier Section Video Section T uner Section ■ FM ■ AM General ■ Video Inputs ■ Video Outputs ■ A udio Inputs ■ A udio Outputs Specifications and features are subject to change without notice. Power Output 2 channels driv en: 90 W + 90 W (8 Ω , 20 Hz–20 kHz, FTC) 155 W + 155 W (6 Ω , 1 kHz, JEIT A) Dynamic Po[...]

88 SN 29344101 (C) Copyright 2005 ONKY O CORPORA TION Japan. All rights reserved. I0509-1 Integra Division of ONKYO U.S.A. CORPORATION 18 park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 201-785-2600 Fax: 201-785-2650 http://www.integrahometheater.com Integra Division of ONKYO CORPORATION Sales & Product Planning Div.: 2-1, Nisshin-cho, Ne[...]