Jacuzzi J-DREAM II manual

J-DREAM II Shower System OWNER’S MANUAL Assembly, Installation & Operating Instructions TM[...]

IMPORT ANT SAFETY INFORMA TION READ ALL INST ALLA TION INSTRUCTIONS Save These Instructions for Future Use. Owner's Record Jacuzzi Whirlpool Bath does not recommend prolonged periods of use of the steamer. Prolonged use of the steam system can raise the internal human body temperature excessively and impair the body's ability to regulate [...]

Part I Assembly & Installation Specifications _______________________________________________________________________ 2 General Information __________________________________________________________________ 3-4 Packaging __________________________________________________________________________ 5 Hardware Identification ________________________[...]

WHIRLPOOL B ATH R J-Dream II Owner's Manual FRONT VIEW PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. SPECIFICATIONS 2 TOP VIEW DIMENSIONS 60" (1524mm)L 42" (1067mm)W 83" (2108mm)H TOTAL WEIGHT/ FLOOR LOADING 833 lb (379 kg) 47.6 lb/ft 2 (233 kg/m 2 ) REQUIRED WATER SUPPLY 6 gpm (23 liter/min) @ 30-65 psi (2.1-4.6 [...]

Read all instructions before beginning assembly and installation. General Assembly Information The J-Dream II shower unit is installed into a niche with the drain towards the left hand side of the unit as you face the shower door. This manual details the assembly, installation and operation. After the drain, water supply stub-out, and electrical su[...]

Electrical requirements Your J-Dream II, as it comes from the factory, requires a GFCI protected 240 VAC 3- wire 20 AMP 50-60 Hz circuit (2 conductor with ground) for single (1) phase electrical service, and must be in a separate circuit having no other appliance connected in that circuit. If you do not have this kind of circuit, a qualified electr[...]

J-Dream II Packaging 6 cartons packed together on a wooden crate. Contents of cartons: • Wall Panels • Door Frame • Base/Cover (includes product accessory pack and owners manual) • Back Wall • Seat Wall • Equipment/Seat Wall 5 J-Dream II Owner's Manual[...]

J-Dream II Owner's Manual Letters (A) are used in the illustrations of the assembly procedure. 6 FLA T W ASHER 1/4" P AN HEAD SCRE W #10-24 x 3/4 " LO CK NUT 10-24 C W ASHER SCREW B NUT D FLA T HEAD SCRE W M4x10mm SCREW E P AN HEAD SCRE W #12 x 1/2 SCREW F HEX BOL T 1/4-20 x 1.5" BOL T G SELF-T APPING M6x50mm BOL T H U-CLIP 10-2[...]

7 Rough-in W ASHING MACHINE OUTLET BOX CONNECT #8 GAUGE (10mm 2 ) MINIMUM SOLID COPPER BOND WIRE T O THE HOUSE ELECTRICAL P ANEL OR APPROVED LOCAL GROUND. AN APPROVED GROUND MA Y BE AN 8 FOOT LONG GROUND ROD (3 METER LONG EARTH ROD), A PLA TE ELECTRODE, OR OTHER ACCEPT ABLE BOND. CHECK YOUR LOCAL BUILDING CODE FOR REQUIREMENTS. (SEE P AGE 22 FOR BO[...]

8 Locate Base to provide assembly access to all sides Remove Base from carton labeled Base/Top . Place Clear Top in carton to prevent damage. (The Clear Top will not be installed until the unit has been fully assembled and plumbed). Position the J-Dream base on the floor so that you have work access to all four sides of the unit during assembly. (A[...]

9 Drain Fitting (provided with unit) Leave enough flexibility in the waste line to allow the end of the stub-out to be blocked temporarily in a position under flush with the floor surface. This will allow the shower unit to slide across the floor into position without having to lift the shower unit. Remove the block and pull the drain assembly up t[...]

10 Attach Seat W alls to Base (J-Dream II with stereo shown) Bolts (8) Nuts (8) G J Align four holes on seat wall frame over base and insert bolts and tighten nuts from underneath. W ashers (8) I Equipment Seat W all Non-Equipment Seat W all J-Dream II Owner's Manual[...]

11 Attach Panel #2 to Seat W all Frame Slide in panel feeding between frame and edge of seat wall. Align to frame and fasten panel to frame. Important: do not caulk panel to seat wall as the seat wall is hinged and designed to swing open. F Screw (4) C W asher (4) T op View Move Frame Seat W all Seals When Panel #2 is installed and put in position [...]

12 Attach Panel #3 to Seat W all Frame Slide in panel feeding between frame and edge of seat wall. Align to frame and fasten panel to frame. Important: do not caulk panel to seat wall as the seat wall is hinged and designed to swing open. T op View Move Frame Seat W all C W asher (4) F Screw (4) Seals Panel #3 Y ou may want to swing the hinged seat[...]

13 Install Back W all Caulk the bottom and sides of back wall where indicated in the illustrations below. Install fasteners. Now align the back wall parallel to the pan lip to center the back wall between the seat walls. Screw (4) B W asher (8) C Nut (4) D Caulk A A Screw (4) B B Caulk W asher (8) C Nut (4) D B Seat walls not shown in this illustra[...]

B A A. Caulk W asher (10) C Nut (3) D Screw (3) B B Reinstall bolts (4) and washers (4) removed from seat wall and bracket Seat wall attaches to panel #1 and #4 in three places. Seat wall attaches to panel #1 and #4 in two places. Caulk Narrow side of panel faces toward the front Panel #1 Panel #4 14 Attach Panels #1 and #4 to Seat W alls Remove 4 [...]

15 Attach Brackets to Seat W all Frames and L Bracket to left Angle Bracket J-Dream II Owner's Manual B B A C A 17" 58-3/8" TOP O F FRAME Screw (2) Note: only the left side has this L bracket installed. An gle Bracket with V elcro ® strips K W asher (2) D Nut (2) B C L Bracket U-Clip A B Screw (2) Bolt (remove top bolt from seat wal[...]

Caulk B Screw (3) C W asher (3) Nut (3) D T op View (right side) Notch Side View (right side) B Screw (3) C W asher (3) Nut (3) D T op View (left side) Side View (left side) Notch Caulk 16 Attach Painted Angle Brackets to Panels #1 and #4 Note that each angle bracket has a notch on the top and bottom. This notch does not get screwed against the sid[...]

17 Attach Door Frame to Angle Brackets and Base Frame Before proceeding, make sure the seat walls are closed and fastened. See detail B on page 15. Align door frame over tabs on base frame and pan lip. Pan lip is to fit into corner posts of door frame. Align holes along sides of door frame with angle brackets and mark this position of the angle bra[...]

18 Attach T op Frame to Door Frame, Back W all and Seat W all Frames Press/tap top frame into door frame, aligning notch in door frame with corner of top of frame while aligning with corners of enclosure. Frame snaps down into door frame and back snaps over back wall. Install bolts (4) through top frame and into left and right seat wall frames. To [...]

19 Feed the four hoses and controller cable from the back wall and connect them as shown. The steam hose connection uses a hose clamp while the other hoses use spring clamps that are on the hoses. Also feed the CD/Radio wire bundle to the back wall. (J-Dream II with stereo only.) J-Dream II Owner's Manual Back of Left Seat W all CD/Radio conne[...]

20 J-Dream II Owner's Manual Use cable ties to attach the CD/Radio wire bundle to the cascade hose. The hoses from valves 1 and 3 and the steam hose are loosely attached to their mounting brackets to allow the slack when connecting them and when the hinged seat wall is swung open (like a door) to access equipment. After they have been connecte[...]

21 Connect the hoses routed from the back wall as below (grayed lines are pre-attached). Connect the controller line. The red and black leads in the CD/Radio wire bundle must be hooked up to the corresponding colored leads of the power supply. Connect the speaker leads. Connect the two SteamPro power cords after unraveling them. J-Dream II Owner&ap[...]

22 Bonding (top left hand side of right hand equipment seat wall) J-Dream II Owner's Manual Connect a #8 guage (10mm 2 ) minimum solid copper bond wire to the house electrical pannel or an approved local ground. An approved ground may be an 8 foot long ground rod (3 meter long earth rod), a plate electrode or ther acceptable bond location. Che[...]

1. Make sure electric power is OFF at main breaker. 2. Static test water supply hoses for leaks. 3. Plug power cord into GFCI protected wall outlet. 4. Move the assembled J-Dream II into final position. 5. Connect 2" shower drain (see page 9). 6. Adjust the levelling screws in the J-Dream II base feet and lock them in position. 7. Recheck fit [...]

24 Attach Front Panels to Unit Remove this screw before operation Ground Wire Speaker and power leads B An t e nna Wire Rear view of CD/radio Screw (2) T innerman ® Nuts (pre-installed) Front Panel B C D D Front Panel V elcro ® Screw (2) L Important: Attach CD/Radio ground wire here V elcro ® B A A C Frame Screw - to be removed to permit attachm[...]

25 Place cover on top of unit. Align notch in cover with the corresponding notch in the top metal frame. J-Dream II Owner's Manual T op Cover[...]

26 T urn On Electric Power at Main Breaker Operate Unit and Check for Leaks Attach Bottom Front Panel to Unit Enclosure Base Frame Panel V elcro ® V elcro ® Removable Face Panels Use finishing strip material (not provided) to cover gap between J-Dream II and finshed wall. Do not attach finishing strips to face panels. Screws Bottom Face Panel fas[...]

27 FIGURE 1. CONTROL PANEL AND DISPLAY FIGURE 2. MIXER CONTROL Part II: Operating Instructions CONTROL PANEL System control is provided by the electronic display located inside the shower cabin (see Figure 1) The display is used to start up the five functions of the unit: the shower, the cascade waterfall, the hydromassage (all jets), hydromassage [...]

Starting the Hydromassage The J-Dream allows you to enjoy the benefits of a real hydromassage. The hydromassage is created by the combined action of 16 water jets (four sets of 4 ). The action of each group of jets is either alternated or pulsed. To start the hydromassage jets, p ress the JETS button once (Figure 1). This will activate the jets on [...]

29 Care and Maintenance of SteamPros Maintenance of the Steampros includes flushing and visually inspecting for water leaks. To flush the units: 1. Turn OFF power to the unit. 2. To gain access to the SteamPros, the seat wall (equipment wall) must be swung open. To do so, remove the three screws from door frame (refer to page 17, diagram A). Then r[...]

Printed in the U.S.A. Printed on Recycled Paper PRODUCT SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE. USE INSTALLATION INSTRUCTIONS SUPPLIED WITH PRODUCT. ©1997 Jacuzzi Whirlpool Bath K922000 8/13/04 Jacuzzi Whirlpool Bath P.O. Box 702168, Dallas, TX 75370-2168 Service Support: Call (800) 288-4002 Jacuzzi Whirlpool Bath has obtained applica[...]

31[...]

32[...]

Jacuzzi Whirlpool Bath Limited W arranty Shower System Pr oduct WARRANTY COVERAGE Jacuzzi Whirlpool Bath (the “Company”) offers the following express limited warranty to the original purchaser of any Jacuzzi Whirlpool Bath Shower System product (“unit”) who purchases the product for personal or single family use (“user”). The Company wi[...]

RESPONSIBILITIES OF OTHERS Inspecting the unit prior to installation is the responsibility of the installer or building contractor who acts on behalf of the user. They are responsible for ensuring the unit is free of defect or damage. Notices are placed on and in the unit and on the shipping carton advising the installer of this responsibility. In [...]