English dropdown-ico

JAI CV-M532 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of JAI CV-M532, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of JAI CV-M532 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of JAI CV-M532. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of JAI CV-M532 should contain:
- informations concerning technical data of JAI CV-M532
- name of the manufacturer and a year of construction of the JAI CV-M532 item
- rules of operation, control and maintenance of the JAI CV-M532 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of JAI CV-M532 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of JAI CV-M532, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the JAI service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of JAI CV-M532.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the JAI CV-M532 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    Opera tion Manual Remote Head Monochrome CCD Camera (Rev.E) CV -M532[...]

  • Page 2

    CV -M53 2 DECL ARA TION OF CONFORMIT Y AS D EFINE D B Y T HE C O UNC IL D IREC T IV E 89/336/EEC E MC (E LECTR O MAG N E TIC C OMP A TI B ILITY ) WE HE R E WITH DECLAR E THA T TH IS PRODUCT C OM PLI E S WITH THE FOLL OWI NG PR OVISIONS APPL YI NG T O IT . E N-50081-1 E N-50082-1[...]

  • Page 3

    - 2 - CV -M53 2 T able of Contents T able of Contents .............................................................................................................. ......................... 2 1 . General ................................................................................................................................................ [...]

  • Page 4

    - 3 - CV -M53 2 1. General The model CV -M532 is a new remote micro-head camera system featuring virtually identical performance and function of the popular CV -M50 standard machine vision camera. Precisely installed CCD imager (1/3") and miniature size (ø12mm) allows access to very contained spaces. The remote micro-head weights only 5g (0.0[...]

  • Page 5

    - 4 - CV -M53 2 3. Main F eatures • Miniature-sized remote head - ø12mm (0.47") • 1/3" Hyper HAD interline transfer CCD imager , 768(H) x 494(V) for E IA and 752(H) x 582(V) for CCI R • High resolution - horizontal 570 TV lines for EIA • Excellent S/N - better than 56dB • High sensitivity - 0.2 lx minimum illumination on CCD im[...]

  • Page 6

    - 5 - CV -M53 2 4. Locations and F unctions 4-1. CCU 4-2. HEAD 1 12P connector : T o connect camera head with camera control unit (For Camera Head) 2 Video output connector : T o output video VS1.0Vp-p (BNC connector) 3 SW1 switch : T o set shutter speed and function modes 4 6-pin Multi connector : Output WEN/EEN signal and input external trigger p[...]

  • Page 7

    - 6 - CV -M53 2 5. Pin Assignment 5.1. 12-pin Multi-connector (DC-IN/SYNC.) T ype: HR10A-10R-12PB (Hirose) male Seen from rear. Notes: *1 ) Signals on pin no. 6, 7 and 9 can be changed by jumper setting. See “7.3. Jumper Settings” for more information. *2 ) In Edge Pre-select and Pulse Width Control mode do not input ext. VD signal. 5.2. 6-pin [...]

  • Page 8

    - 7 - CV -M53 2 6. F unctions and Operations 6.1. Input/Output of HD/VD Signal 6.1.1. Input of External HD/VD Signal As factory setting the camera can be synchronized by external HD/VD signals. The signal level must be 4.0V p-p +/- 2.0V at the input with the 75 Ohm termination ON. T o change to non-terminated input, see instructions in “7. Mode S[...]

  • Page 9

    - 8 - CV -M53 2 T o use this mode Set: SW1-4 to ON for ext. trigger shutter SW1-5 to OFF for field accumulation SW1-6 to ON for non-interlaced SW1-1,2 and 3 to shutter speed Input: Ext. trigger to pin 5 on 6 pin multi connector. Ext. HD to pin 6 on 12-pin multi connector. (If used). 75 Ohm termination is done with SW2-1 (HD) and SW2-2 (ext.trigger)[...]

  • Page 10

    - 9 - CV -M53 2 6.3.2. Pulse Width Control Mode The pulse width control mode will only work in non-interlaced field accumulation mode. The exposure is controlled by the low period of the ext. trigger pulse. The exposure starts at the first HD pulse after the falling edge of the ext. trigger pulse. The exposure ends at the first HD pulse after the r[...]

  • Page 11

    - 10 - CV -M53 2 Cautions in the Pulse Width Control Mode. 1. Pulse width control mode is effective only in non-interlaced field accumulation mode. 2. The exposure start may be delayed up to 1H max., when the falling edge of ext. trigger pulse is not synchronized with the falling edge of ext. H D signal. T o avoid this 1H jitter and delay, the fall[...]

  • Page 12

    - 11 - CV -M53 2 6.3.3. Star t/Stop T rigger Mode The Start /Stop trigger will work in 3 modes: 1. Interlaced with frame accumulation. 2. Interlaced with field accumulation. 3. Non-interlaced with field accumulation. The exposure time is controlled by the interval between the ext. trigger pulse and the ext. VD signal. The exposure starts at the fir[...]

  • Page 13

    - 12 - CV -M53 2 Cautions in the Star t/Stop T rigger Mode. 1. The input of ext. VD signal must be given continuously to synchronize with int. VD signal. It is not possible to input ext. VD signal randomly. 2. The exposure start may delay up to 1H max., when the falling edge of ext. trigger pulse is not synchronized with the falling edge of ext. H [...]

  • Page 14

    - 13 - CV -M53 2 6.3.4. Long Time Exposure Mode The Long time exposure will work in 3 modes: 1. Interlaced with field accumulation. 2. Interlaced with frame accumulation. 3. Non-interlaced with field accumulation. The exposure time is the interval between 2 ext. VD pulses sent to the camera VD input. Each ext. VD pulse will reset and restart the in[...]

  • Page 15

    - 14 - CV -M53 2 Cautions in the Long Time Exposure Mode. 1. Theoretical exposure time is as follows. EIA: 1/30 sec. to ∞ . 2. It is recommended not to use exposure > 2 sec. since visible dark-current noise may occur. 3. Ext. HD signal (4.0 Vp-p ± 2.0V at 75 Ohm terminated) has to be input continuously The falling edge of Int. HD signal and E[...]

  • Page 16

    - 15 - CV -M53 2 7. Mode Setting Caution on Mode Setting. Before making any mode or jumper setting turn the po wer OF F . 7.1.1. SW1 Switch on the Rear Panel Factory settings for SW1 are with all 8 switches in OFF position. 7.1.2. T able for SW 1 Setting 7.1.3. T able for Shutter T ime Caution on Shutter . The image can flicker when the illuminatio[...]

  • Page 17

    - 16 - CV -M53 2 7.1.4. Ext. T rigger Shutter Mode When trigger select SW1-4 is ON. The camera is in ext. trigger shutter mode. The SW1-1, SW1-2 and SW1- 3 are for selecting the shutter speed. The range is from OFF to 1/10,000 second in 8 steps. For each external trigger pulse, the camera will make an exposure with the selected shutter speed. The s[...]

  • Page 18

    - 17 - CV -M53 2 7.3. Jumper Settings Caution on Jumper Setting. Before making any mode or jumper setting turn the po wer OF F . Jumpers for mode setting are found on the boards PK8054 & PK8057. The following modes are available with jumper setting: Input/Output Mode of HD/VD signal. (HD/VD input is factory setting) Edge Pre-select Mode. (Facto[...]

  • Page 19

    - 18 - CV -M53 2 7.4. Location of SW2 and Jumpers Jumpers are shorted with a 0 Ohm resistor or by a soldering between the 2 points. T o remove the solder tin from a jumper position, use a special tin remover such as de-soldering wick. 7.4.1. Board PK8054 Side B 7.4.2. Board PK8057 Side A R127[...]

  • Page 20

    - 19 - CV -M53 2 8. Adjustment of Video Signal Output Level When an alignment of a video output signal is required, remove the camera housing and adjust potentiometers VR3, VR4 and VR5 on the PK8056 board while measuring their levels at the video output connector. This adjustment should only be done in a setup with a standard TV test chart and cont[...]

  • Page 21

    - 20 - CV -M53 2 9. External Appearance Unit : mm (inches) 9.1 CCU 9.2 HEAD[...]

  • Page 22

    - 21 - CV -M53 2 10. Specifications Scanning system EIA 525 lines 30 frames/sec. CCD sensor Monochrome "1/3" Hyper HAD IT CCD Sensing area 4.9 mm ( h) x 3.7 mm ( v) Effective pixels 768 (h) x 494 (v) Elements in video output 758 (h) x 486 (v) Cell size 6.35 (h) x 7.4 (v) µm Resolution (horizontal) 570 TV lines Resolution (vertical) 485 T[...]

  • Page 23

    - 22 - CV -M53 2 11. Appendix 11.1. Precautions Personnel not trained in dealing with similar electronic devices should not service this camera. The camera contains components sensitive to electrostatic discharge. The handling of these devices should follow the requirements of electrostatic sensitive components. Do not attempt to disassemble this c[...]

  • Page 24

    JAI America, Inc., USA Suite 450 23046 Avenida de la Carlota Laguna Hills, CA 92653 USA Phone +1 949 472 5900 Fax +1 949 472 5908 www.jai.com JAI Corporation, Japan German Industry Center 1-18-2 Hakusan, Midori-ku Y okohama, Kanagawa 226-0006, Japan Phone +81 45 933 5400 Fax +81 45 931 6142 www.jai-corp.co.jp JAI A·S, Denmark Produktionsvej 1, 260[...]