Jensen Mobile Multimedia AM/FM/DVD Receiver VM9510 manual

7-INCH TFT 7-INCH TFT MODE VM9510 MUTE AS/PS BAND DISP PWR ENTER AM/FM/DVD/MP3 RECEIVER 7-INCH DIGITAL TFT OPEN Push Push AV AUX IN Introduction Congratulations on your purchase of the Jensen VM9510 Mobile Multimedia AM/FM/DVD Receiver . Features • Motorized 7” digital TFT screen • AM/FM stereo tuner • TV tuner w/diversity antenna input •[...]

VM9510 2 Manual del Usuario Guide d'Utilisateur ¡Gracias! Gracias por elegir los productos Jensen. Esperamos que encuentre en este manual instrucciones claras y fáciles de seguir. Si se toma unos pocos minutos para leerlo, aprenderá cómo utilizar todas las funciones de su nuevo AM/FM/DVD Multimedia Móvil Jensen VM9510 para su máximo entr[...]

VM9510 3 Pre-installation 1. Press the metal levers on both sides to remove the half-sleeve from the radio. 2. Rem o ve the tr im ring . 3. Install the half-sleeve. a. Install adapter if necessary (optional). b. Install half-sleeve into adapter or dashboar d (only use the supplied screws). Do not force the sleeve into the opening or cause it to ben[...]

VM9510 4 Wi r in g Wiring Connections 1. TV T UNER 2. ANTENNA 3. POWER A NTEN N A WIRE (Blue) – Connect to a mot o rized ( powe r ) antenna and/or to a remote turn-on lead for an amp lifier . 4. CONS T A NT POWER WIRE (Yellow) – Conn e ct the 12V PLUS c o ns t a nt power wire to a live 12 volt wire in the vehicle. Before making a co nnection, c[...]

VM9510 5 Cableado Conexiones de Cableado 1. SINTONIZADOR DE TV 2. ANTENA 3. CABLE DE CONEXIÓN DE ANTENA (azul) - Conectar a una antena motorizada (encendida) y/o a una toma remota de encendido para un amplificador . 4. CABLE DE ENERGÍA PERMANENTE (amarillo) - Conectar el cable de energía permanente 12V PLUS a un cable vivo con 12 voltios en el v[...]

VM9510 6 Installation After completing the wiring connections, turn the unit on to confirm operation (ignition switch must be on). If unit does not operate, recheck all wi ring until problem is corr ected. Once proper operation is achieved, turn off the ignition sw itch and proceed with final mounting of the chassis. NOTE: For proper operation of t[...]

VM9510 7 Final ISO-DIN Installation 1. Remove trim ring. 2. Mount factory brackets on new radio using existing screw s from old radio. 3. Slide radio chassis into dash opening and secure. 4. Reinstall dash panel. Instalación Final ISO-DIN 1. Quite el anillo ornamental del frente del radio. 2. Monte en el nuevo radio los soportes de fábrica usando[...]

VM9510 8 6 2 15 16 17 1 3 4 7 5 7-INCH TFT 7-INCH TFT MODE VM9510 MUTE AS/PS BAND DISP PWR ENTER AM/FM/DVD/MP3 RECEIVER 7-INCH DIGITAL TFT OPEN Push Push AV AUX IN 8 9 10 11 12 13 14 MODE PWR ENTER VM9510 VM9510 MUTE Push Push AV AUX IN 1.15 MEGA-PIXELS 7-INCH DIGITAL TFT DISP 7-INCH DIGITAL TFT OPEN DVD AM/FM/DVD/MP3 RECEIVER TILT ASPECT V. S E L [...]

VM9510 9 Remote Controls The VM9510 has two remote controls: A full- featured hand-held remote control, and a limited featu r e "Kid Z one" r e mote c o ntrol for r ear seat passengers. Both remotes use a CR2025 Lithium battery . T he battery compartment is located on the back of the remote control near the bottom edge. T o replace the ba[...]

VM9510 10 Operation (continued) NO TE: Some D VDs require specific oper ation or allow only limited operatio n during playback which may not respond to all operating commands. When this occurs, the symbol appears on the TFT screen, indicating tha t the operation is not permitted by the play er or the disc. Power Press the PWR button (1) to turn the[...]

VM9510 11 Opération (continuée) A NO TER : Cer tains D VD exigent une opération spécifique ou permet une opération limitée pendant la repr o duction qui peuv ent ne pas répondre à toutes les commande d'opérations. Lor sque cela arrive, le symbole apparaît sur l'écran TFT indiquant que l'opération n'est pas permise pa[...]

VM9510 12 Operation (continued) Tr eb l e TFT Screen Closed : T o adjust the treble level, press and hold the ROTAR Y ENCODER (3) for > 2 seconds until “Sub-W” appears in the LCD. With “Sub-W” displayed, press the knob again 2 times to access the treble control. Turn the ROT A R Y ENCODER to adjust the treble from -07 (lowest) to +07 (hi[...]

VM9510 13 Operation (continued) Fader TFT Screen Clos ed : T o adjust the fader, press and hold the ROT ARY ENCODER (3) for > 2 seconds until “Sub-W” appears in the LCD panel. With “Sub-W” displayed, press the kn ob again 4 times to access the fader control. Turn the ROT ARY ENCO DER to adjust the fader between the front and rear speaker[...]

VM9510 14 Operation (continued) Clock Y ou can only view the clock or modify its settings with the TFT screen closed. CLOCK DISP LA Y Press the DISP (5) button to show the clock in the LCD panel. CLOCK ADJUSTMENT (TIME) Press and hold the DISP (5) button until the clock flashes in the LCD panel. Push the ENTER button (4) to the left or right to adj[...]

VM9510 15 Operation (continued) System Menu Options T o access the system menu, press the OSD (23) button to display the on -screen menu. Push the ENTER (4) button down to highlight “SYSTEM”, and then press the ENTER button. “AUTO” will become highlighted in red. Push the ENTER button d own to highlight the property you want to modify , and[...]

VM9510 16 T uner Oper ation Switching to Radio Mode TFT Screen Clos ed : Press the MODE button (6) to move through the available modes in the following sequence: FM1, CD, A V1, AV2, and TV1. S top on “FM1” to access radio mode. The LCD panel displays the current radio statio n, preset memory number (if applicable), and frequency . TFT Screen Op[...]

VM9510 17 T uner Oper ation (continued) Manual Tuning Push the ENTER button (4) up or down to move the radio frequency number up or dow n one step. Scanning Push the ENTER button (4) to the right to scan forward through strong stations in the current band. Push the ENTER button to the left to scan backwards . The radio pauses for five seconds at ea[...]

VM9510 18 T uner Oper ation (continued) Auto Store (AS) / Preset Scan (PS) Automatic S toring Use the Auto Store function to select six strong stations and store them in the current band. 1. Select a band (if needed). 2. Press AS/PS (8) for > 2 seconds to activate the Auto S tore function. The new stations replace stations already stored in that[...]

VM9510 19 CD Play er Operation Y ou must be familiar with the remote control (see the “Remote Controls” diagram on page 9) to perform some of the step s listed in this section. Switching to CD Mode TFT Screen Closed : Press the MODE button (6) to move through the available modes in the following sequence: FM1, CD, A V1, A V2, and TV1. Stop on ?[...]

VM9510 20 Operación del Equipo de CD (continuado) Avance Rápido/Retroceso Rápido • Presione el botón 2 (10) para avance rápido. Mantenga presionando y soltando el botón para incrementar la velocidad 2X a 4X, 8X y 32X. • Presione el botón 1 (9) para avance rápido. Mantenga presionando y soltando el botón para incrementar la velocidad 2X[...]

VM9510 21 MP3 Player Operation Instructions for Insert/Eject, Play/Pause, Stopping Play , T rack Selection, Fast Forward/Fast Reverse, Scan, and Random Play are the same for CD and MP3 operation. Please see the CD Player Operation section for information about these topics. Y ou must be familiar with the remote control (see the “Remote Contr ols?[...]

VM9510 22 MP3 Player Operation (continued) Direct Access (Requires Remote Control) Press the number buttons (1, 2, 3, 4, 5, 6, 7, 8, 9, 0) on the remote control to directly access a track in the current folder. Select Directory 1. Press the button (12) to stop MP3 play . 2. Press the P. T I M E button (40) on the remote control to display the main [...]

VM9510 23 D VD Player Operation Y ou must be familiar with the remote control (see the “Remote Controls” diagram on page 9) to perform some of the steps listed in this section. NOTE: When properly installed, DVD video cannot be displayed on the main TFT screen unless the parking break is applied. If you attempt to play a DVD while the vehicle i[...]

VM9510 24 D VD Oper ation (continued) Adjusting the Positi on of the TFT Scree n Moving the Screen In/Out Press the IN/OUT button (22) to move the screen in or out. Y ou will hear three beep tones. If in the “Out” position, the TFT scr een moves t o the “I n” position. If the TFT screen is “In”, it will move “Out”. If the TFT screen[...]

VM9510 25 D VD Player Operation (continued) Manually Adjusting the Angle From Left to Right T o manually adjust the left/right angle of the TFT screen, follow these steps: 1. Make sure the TFT screen in “Out”. Press the IN/OUT button ( 22) if necessary . 2. Locate the extender mechanism behind the screen. 3. Firmly grasp both sides of the scree[...]

VM9510 26 D VD Player Operation (continued) Accessing the DVD Menu Press the MENU button ( 37) on the remote control to recall the main DVD menu. Use the directional (arrow) buttons ( , , & ) to select a title from the menu. Press the TITL E button (48) on the remo te control to return to the beginning of the disc. Moving Through Chapters Press[...]

VM9510 27 D VD Oper ation (continued) Direct Search (Requires Remote Control) T i tl e Se arc h 1. Press the P. T I M E button (40) on the remote control to display the main menu. 2. Use the left/right arrows ( & ) on the remote control or the ENTER button (4) on the radio to select the Title (T) option. 3. Use the up/down arrows ( & ) on t[...]

VM9510 28 D VD Oper ation (continued) Tim e S e a r c h 1. Press the P. T I M E button (40) on the remote control to display the main menu. 2. Use the left/right arrows ( & ) on the remote control or the ENTER button (4) on the radio to select the Time Search ( ) option. 3. Use the down arrow ( ) on the remote control or the ENTE R button (4) o[...]

VM9510 29 D VD Oper ation (continued) Controlling Playback S toppi ng Playback Press the button (12) to stop DVD play . S till Playb ack Press the button (1 1) to suspend or resume disc play . Frame-by-Frame Playback 1. Press the P. T I M E button (40) on the remote control to display the main menu. 2. Use the left/right arrows ( & ) on the re [...]

VM9510 30 D VD Oper ation (continued) Repeat Play (Requires Remote Control) Repeat Chapter , Title, or Disc •P r e s s t h e REPEAT (44) button on the remote control once to repeat the current chapter. “chapt. ” appears near the top of the TFT screen. • Press the REPEAT button on the remote control twice to repeat the cur rent title. “tit[...]

VM9510 31 D VD Oper ation (continued) V iewing an Alternate Pic tu re An g le (Requ ire s Remo t e Cont ro l) For discs recorded with multiple angles, press the ANGLE button (41) on the remote contr ol to toggle available angles of the on-screen image. Zooming Use the Zoom function to enlarge and pan through the video image. 1. Press the P. T I M E[...]

VM9510 32 D VD Oper ation (continued) Setting the Asp ect Ratio Press the ASPECT button (20) to toggle between Wide, Normal, and Cinema aspects. • Wide = 16:9 ratio • Normal = 4:3 ratio • Cinema = full screen NOTE: The ASPECT button does not work in “Tuner” mode. Adjusting the V ideo Screen Settings T o adjust the video output, press the [...]

VM9510 33 D VD Oper ation (continued) Main Menu Functions A number of operations can be carried out using the main menu at the top scre en. T o access the main menu, press the P. T I M E button (40) on the rem ote control . When the menu bar is visible and an item is selected, it will be becom e highlighted and the appropriate cursor keys to operat[...]

VM9510 34 Operación del Equipo de DVD (continuado) Funciones de Menú Principal Un número de operaciones se pueden llevar a cabo utilizando el menú principal de la parte superior de la pantalla. Para acceder al menú principal, presione el botó P. T I M E (40) en el control remoto. Cuando una barra de menú es visible y un ítem se selecciona, [...]

VM9510 35 Operation Platine D VD (continué) Fonctions menu principal V ous pouve z exécuter de nombreuses opérati ons en utilisant le menu principal en haut de l'écran. Pour accéder au menu principal, appuyez sur le bouton P. T I M E (40) sur la télécommande. Lorsque la barre menu est visible et un article a été sélectionné il sera [...]

VM9510 36 D VD Oper ation (continued) Access Control (DVD/VCD) Child Lock Activating Child Lock 1. Press the P. T I M E button (40) on the remote control to display the main menu. 2. Use the left arrow ( ) on the remote control or the ENTER button (4) on the radio to move to select the User Preference Settings ( ) option. 3. Use the down arrow ( ) [...]

VM9510 37 CD Operation (continued) Access Control (DVD/VCD) ( c ontinued) Authorizing Discs The DVD player maintains a list of 120 author ized (child safe) disc titles. Each time an approved disc is played, the title is placed at the top of the list. Once the list becomes full, new titles are added in place of the last title in the list. T o author[...]

VM9510 38 2. Ingrese un código de 4 dígitos. 3. Utilice la flecha hacia abajo ( ) para seleccionar el Nivel Paternal. 4. Desde el menú "Nivel Paternal", utilice la flecha derecha ( ) para llegar al campo de Ajuste de V alor. 5. Utilice las flechas hacia arriba o abajo ( y ) p ara seleccionar una categoría de 1 a 8. • Una categoría [...]

VM9510 39 CD Operation (continued) Access Control (DVD/VCD) ( c ontinued) Changing the 4-digit Code 1. Display the “Access Control” menu. (See “Activating Child Lock” on page 36.) 2. Enter your 4-digit code. 3. Use the down arrow ( ) to select Change Code. 4. Use the right arrow ( ) to move to the Change Code field. 5. Enter the new 4-digit[...]

VM9510 40 Operación de TV Cambio a Modo TV Presione el botón MODE (6) para moverse a través de los modos disponibles en la secuencia siguiente: FM1, CD, A V1, A V2 y TV1. Deténgase en "TV" para acceder al modo TV . La pantalla TFT muestra la estación actual y todos lo s seis canales preconfigurados en memoria. Cambiando el Canal Busc[...]

VM9510 41 Operación de TV (continuado) Canales Preconfiguardos (continuado) Almacenando una Estación 1. Seleccione una estación. 2. Presione el botón de preselección (9-14) por tres segundos. El botón de preselección aparece en el panel LCD. Sintonizando una Estación Presione el botón de preselección (9-14) pa ra seleccionar la estación [...]

VM9510 42 T r oubleshooting Mechanical Errors If a mechanical error occurs while opening the TFT screen, t he screen stops moving and beeps three times. If a mechanical error occurs while closing th e TF T screen, the screen beeps three times and returns to the previous position. Problem Cause Corrective Action No power to unit Fuse(s) blown Check/[...]

VM9510 43 Cor r ección de Problemas Errores Mecánicos Si ocurre un error mecánico mientras esté abr iendo la pantalla TFT , la pantalla deja de moverse y hace tres sonidos. Si ocurre un error mecánico mientras se cierra la pantalla TFT , la pantalla realiza tres sonidos y retorna a su posición previa. Problema Causa Correcci on No hay energí[...]

VM9510 44 Dépannage Des erreurs mécaniques Si une erreur mécanique parvient en ouvrant l'écran TFT , l'écran s'a rrête de bouger et bipe trois fois Si une erreur mécanique parvient en fermant l'écran TFT , l'écra n bipe trois fois et revient à la position précédente. Probléme Cause Mesure à Prendre Pas de puis[...]

VM9510 45 12-Month Limited Warr anty AUDIOVOX CORPORA TION (the Company) warrants to the orig inal retail purchaser of this product that should this product or any p art thereof, under normal use and conditions, be proven defective in mat erial or workmanship within 12 months from th e date of original purchase, such defect(s) will be re paired or [...]