English dropdown-ico

Kaidan KiWi-L manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Kaidan KiWi-L, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Kaidan KiWi-L one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Kaidan KiWi-L. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Kaidan KiWi-L should contain:
- informations concerning technical data of Kaidan KiWi-L
- name of the manufacturer and a year of construction of the Kaidan KiWi-L item
- rules of operation, control and maintenance of the Kaidan KiWi-L item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Kaidan KiWi-L alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Kaidan KiWi-L, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Kaidan service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Kaidan KiWi-L.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Kaidan KiWi-L item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    K iW i™-L / K iw i™+ User ’ s Guide Photog r aphic VR P anor amic Tripod Head Designed f or the pr o f essio nal, pric ed f o r the novic e...[...]

  • Page 2

    Copyright Information Copyright © 2001 Kaidan Incorporated. All Rights Reserved. First Edition, March 2001. P roducts mentioned herein may be trademarks of their respective companies. Patents Pending. Information in this manual is subject to change without notice and does not represent a commitment on the part of Kaidan. No part of this manual may[...]

  • Page 3

    Page - 3 Assembling the KiWi™ UNP ACKING THE BOX The KiW i-L or the Kiwi + are shipped in a single box and con- sists of two major components. The components are detailed below . NOTE: Only the Kiwi+ is shipped with four detent discs (12,14,18, and 20 positions). Please make sure that all parts are included. Examine the parts for any signs of shi[...]

  • Page 4

    Page - 4 Assembling the KiW i ™ A TT ACHING THE VERTICAL BRACKET T o assemble the KiW i, simply slide the V ertical Bracket onto the Horizontal Bracket in the orientation shown in the various im- ages in this manual. Note: The bottom of the V ertical Bracket has a clamping mechanism with a spring-loaded nylon ball which keeps tension on the horiz[...]

  • Page 5

    Page - 5 Using the KiW i™ A TT ACHING YOUR CAMERA T o mount your camera, first select the appropriate slot in the V ertical Bracket that will best locate the tripod mounting thread on your camera. Y ou may need to reposition the Captive Camera Knob in order to achieve this. T o remove the knob simply slide the knob along the slot to the end that [...]

  • Page 6

    Page - 6 Using the KiW i™ REMOVING THE FRICTION CAP The KiW i+ needs to be disassembled in order to install or change detent discs. The detent discs come in various settings and pro- vide the different angular click-stops. (NOTE: See Disc Selec- tion Chart In Appendix A). T o start, the friction cap must be removed. Loosen the knob located on the[...]

  • Page 7

    Page - 7 W ith the components removed from the top side of the hori- zontal bracket, the lower hub and axle assembly can be slid out and removed. At this point, you’ll be able to install the detent disc into the recessed area on the bottom.[...]

  • Page 8

    Page - 8 W ith the disc removed, you can insert a different disc to change the angular detent spacing. Kaidan offers a variety of discs, with detents ranging from 2 to 22 per disk.. When changing discs, be sure the disc is seated properly and is flush with the top surface of the plate. W ith the new disc inserted, you can begin to reassemble the as[...]

  • Page 9

    Page - 9 Push the axle through the bearing and plate as shown below . Reverse the disassembly . Replace the cap by threading the cap onto the axle as shown below . Continue to thread the cap so that there is no free play in any of the pieces and to compress the rubber washer slightly . When the friction drag feels adequate, turn the Friction cap so[...]

  • Page 10

    Page - 10 The spring plunger that provides the detent action can also be adjusted to vary the force of the click action. Use a flat blade screw driver to move the plunger in and out as desired. A con- venient way to adjust the plunger is to screw the plunger all the way in, until it bottoms out. Then unscrew the plunger about one turn. Once the ind[...]

  • Page 11

    Page - 11 Using the KiW i™ HOW DO I LOCA TE MY NODAL POINT ? This is one of the most frequently asked questions when it comes to QTVR panorama creation. Once you understand the basics, you’ll be able to easily locate the nodal point for any camera and lens combination. Simply put, the nodal point is the point inside your camera where the light [...]

  • Page 12

    S TEP 1: T HE E ASY P ART - T HE S IDE - TO - S IDE A DJUSTMENT Once your cam- era is fastened to your pan head, move around to the front of the unit so you’re looking into the lens. The center of the lens should be directly over the pivot axis of the pan head. Adjust the side-to-side adjustment so the lens is centered over the pivot. W ith the K[...]

  • Page 13

    Page - 13 It may help to first locate the camera all the way to the front or rear and then move it a little bit at a time. This way you’ll more readily see the parallax effect and notice how it im- proves as you slide the bracket. S TEP 3: L EVEL THE C AMERA Once you have located the fore-aft position, you now must level the camera. If your camer[...]

  • Page 14

    Page - 14 surface, then you can use a bubble level. Y ou should be able to locate a small level at a hardware store. If your there are no level surfaces, then you may have to resort to “eyeballing”. S TEP 4: R ECORD Y OUR R ESUL TS After you’ve discovered the two location dimensions, be sure to record the settings. The KiW i has convenient in[...]

  • Page 15

    Page - 15 T AKING PHOTOS WITH THE KIWI™ H OW MUCH O VERLAP ? The amount you turn the camera for each shot varies. It is dependent on a number of factors such as the field of view (the angle) of your camera and lens, as well as which program you intend to use. For example, Apple recommends that the im- ages should overlap by anywhere from one-thir[...]

  • Page 16

    Page - 16 T AKING THE PHOTOS (CONTINUED). Y ou can use the level on your KiW i™ and observe it while you level the tripod. Of course, this task is much easier if your tri- pod also has a tilt head. Once the tripod and KiW i™ are level, now is the time to double check to see if the camera is straight up and down. If it needs to be adjusted, loos[...]

  • Page 17

    Page - 17 Appendix A List of Lens FOV versus Number of Shots Lens (35 mm equiv) 14-15 12 10 8 18-20 14 12 10 22-24 16 14 12 27 18 16 14 35 20 18 16 Disc for 50% overlap of images Disc for 33% overlap of images Disc for 25% overlap of images SHOTS DEGREES OF ANGLE 8 0 45 90 135 180 225 270 315 10 0 36 72 108 144 180 216 252 288 324 12 0 30 60 60 120[...]

  • Page 18

    Page - 18 Camera Adjustment Lug Addendum Because of the various sizes and camera body profiles, we have included a camera adjustment lug as an additional means of keeping your camera mounted in a vertical position. Shown below are examples of various ways to use the Camera Adjustment Lug to mount your camera.[...]