Kenmore POWER MISER 153.335862 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40

Go to page of

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Kenmore POWER MISER 153.335862, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Kenmore POWER MISER 153.335862 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Kenmore POWER MISER 153.335862. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Kenmore POWER MISER 153.335862 should contain:
- informations concerning technical data of Kenmore POWER MISER 153.335862
- name of the manufacturer and a year of construction of the Kenmore POWER MISER 153.335862 item
- rules of operation, control and maintenance of the Kenmore POWER MISER 153.335862 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Kenmore POWER MISER 153.335862 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Kenmore POWER MISER 153.335862, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Kenmore service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Kenmore POWER MISER 153.335862.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Kenmore POWER MISER 153.335862 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    Owners Manual FOR POTABLE WATER HEATING ONLY NOT SUITABLE FOR SPACE HEATING NOT FOR USE IN MOBILE HOMES Model No. 153.335816 40 Gal. 153.335845 40 Gal. High Altitude L.R 153.335862 40 Gal. L.R 153.335916 50 Gal. 153.335942 50 Gal. High Altitude L.R 153.335962 50 Gal. L.R Caution: Read and Follow All Safety Rules and Operating Instructions Before Fi[...]

  • Page 2

    Safety Precautions •,WARNING I Improper installation, adjustment, alteration, service or I maintenance can cause death, serious bodily injury, or property damage. Refer to this manual for assistance or consult your local Sears Service Center for further information. _.WARNING WATER HEATERS EQUIPPED FOR ONE TYPE GAS ONLY: This water heater is equi[...]

  • Page 3

    Safety Precautions AWARNING A gas water heater cannot operate properly without the correct amount of air for combustion. Do not install in a confined area such a closet, unless you provide air as shown in the "Locating The New Water Heater" section. Never obstruct the flow of ventilation air. If you have any doubts or questions at all, ca[...]

  • Page 4

    Safety Precautions AWARNING ] The water heater wi_talled must be prop- [ erly vented to a chimney which terminates outdoors.[ Never operate the water heater unless it is vented to the [ outdoors and has adequate air supply to avoid risks of[ improper operation, explosion or asphyxiation. ] _,WARNING Minimum clearances between the water heater and c[...]

  • Page 5

    Table of Contents Safety Precautions ............................................................................................................................................ 2-4 Table of Contents ................................................................................................................................................ 5 Cus[...]

  • Page 6

    Customer Responsibilities Thank You for purchasing a Sears water heater. Properly installed and maintained, it should give you years of trouble free ser- vice. If you should decide that you want the new water heater profes- sionally installed by Sears call the local Sears Service Center or any Sears store. They will arrange for prompt, quality inst[...]

  • Page 7

    Materials and Basic Tools Needed Materials Needed To simplify the installation Sears has available the installation parts shown below. You may or may not need all of these materi- als, depending On your type of"installation. Gas Water Heater Instaflation Kit ; _ EXPANSION TANKS FOR THERMAL EXPANSION CONDITIONS AVAILABLE IN 2 GALLON AND 5 GALLO[...]

  • Page 8

    Installation Instructions Removing the Old Water Heater Turn "OFF" the gas supply to the water heater. •,WARNING ] If the main gas line shutoff serving all gas appliances is / used, also shut "off" the gas at each appliance. Leave all| gas appliances shut "off" until the water heater installation | s comp ete. QTurn [...]

  • Page 9

    Installation Instructions Locating the New Water Heater You should carefully choose an indoor location for the new water heater, because the placement is a very important consideration for the safety of the occupants in the building and for the most economical use of the appliance. This water heater is not for use in mobile homes or outdoor install[...]

  • Page 10

    Installation Instructions (cont'd) AWARNING A gas water heater cannot operate properly without the cor- rect amount of air for combustion. Do not install in a con- fined area such a closet, unless you provide air as shown in the "Locating The New Water Heater" section. Never obstruct the flow of ventilation air. If you have any doubt[...]

  • Page 11

    Installation Instructions (cont'd) Combustion Air and Ventilation for Appliances Located in Unconfined Spaces Unconfined Space is a space whose volume is not less than 50 cubic feet per 1,000 Btu per hour of the aggregate input rating of all appli- ances installed in that space. Rooms communicating directly with the space in which the applianc[...]

  • Page 12

    Installation Instructions (cont'd) Water Piping AWARNING HO'I-I'ER WATER CAN SCALD: Water heaters are intended to =reduce hot water. Water heated to a temperature which will satisfy clothes washing, dish washing, and other sanitizing needs can scald and permanently injure you upon contact. Some peo- de are more likely to be permanent[...]

  • Page 13

    Installation Instructions (cont'd) Temperature-Pressure Relief Valve _,WARNING At the time of manufacture this water heater was provided with a combination temperature-presseres relief valve certified by a nationally recognized testing laboratory that maintains _eriodic inspection of production of listed equipment or mate- rials, as meeting th[...]

  • Page 14

    Installation Instructions (cont'd) Filling the Water Heater A CAUTION J Never use this water heater unless it is completely filed with water. To prevent damage to the tank, the tank must be filled with water. Water must flow from the hot water faucet before turn ng ON' gas to the water heater. You must provide all wiring of the proper siz[...]

  • Page 15

    Installation Instructions (cont'd) USE WITHOUT POWER CORD (cont'd) 3. A standard ½" conduit opening has been made in the water beater junction box for the conduit connection. 4. Use wire nuts and connect the power supply wiring to the wires inside the water heater's junction box. 5. The water heater must be electrically "g[...]

  • Page 16

    Installation Instructions (cont'd) Venting (cont'd) AWARNING J Be sure vent pipe is properly connected to prevent escape of J dangerous flue gases which could cause deadly asphyxiation. J AWARNING Chemical vapor corrosion of the flue and vent system may occur if air for combustion contains certain chemical vapors. Spray can propellants, c[...]

  • Page 17

    Installation Instructions (cont'd) VENTING SYSTEM EXAMPLE INSTALLATIONS FOR ALL MODELS (cont'd) i - . 2. Horizontal runs require a minimum ¼ rise per foot. 7- 13"HIN. l 35' MAX. 1 3. A vertical run can be no more than 20'. 4. The total vertical and horizontal run cannot exceed 35'. 37 MIN. RISE ¼" PER FOOT ONE E[...]

  • Page 18

    Installation Instructions (cont'd) Venting (cont'd) CUTTING OPENING THROUGH AN OUTSIDE WALL AND COLLAR INSTALLATION After reading the manual and you have determined the location of the opening in the wall, (using the drawing below), cut a 3_" hole through an exterior wall. NOTE: When determining location of the opening in the outside[...]

  • Page 19

    Installation Instructions (cont'd) Gas Piping &WARNING Make sure the gas supplied is the same type listed on the model rating plate. The inlet gas pressure must not exceed 10.5 in. water column (2.6kPa) for natural gas or 13 in. water column (3.2kPa) for propane (LR) gas. The minimum inlet gas pressure listed on the model rating plate is f[...]

  • Page 20

    Installation Instructions (cont'd) Installation Checklist BEFORE LIGHTING THE PILOT: VENT PIPE TO OUTDOORS Check the gas lines for leaks. a. Use a soapy water solution• DO NOT test for gas leaks usinga match or open flame. b. Brush the soapy water solution on all gas pipes, joints and fittings. c. Check for bubbling soap. This means you have[...]

  • Page 21

    Operating Instructions This water heater is equipped with an electrically operated vent- ing system and a standing pilot. For the burner to come on, the water heater thermostat must call for heat. Then the system will begin sequencing, each section proving itself before gas is allowed to flow to the burner. BLOWER MOTOR BEFORE THE WATER HEATER WILL[...]

  • Page 22

    Operating Instructions Lighting AWARNING BEFORE LIGHTING [PROPANE (L,P.) GAS WATER HEATERS]: Propane (LR) gas is heavier than air. Should there be a leak in the system, the gas will settle near the ground. Basements, crawl spaces, skirted areas under mobile homes (even when ventilated), closets and areas below ground level wiU serve as pockets for [...]

  • Page 23

    Operating Instructions (cont'd) Lighting label on the water heater as it appears above the thermostat I FOR YOUR SAFETY READ BEFORE LIGHTING I WARNING If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance has a pilot which must be lighted by h[...]

  • Page 24

    Operating Instructions (cont'd) Temperature Regulation Due to the nature of the typical gas water heater, the water tem- perature in certain situations may vary up to 30°F higher or lower at the point of use such as, bathtubs, showers, sink, etc. Turn the water temperature dial clockwise (_-"',) to decrease the temperature, or count[...]

  • Page 25

    Service and Adjustment Tank (Sediment) Cleaning Sediment build-up on the tank bottom may create varying amounts of noise, and if leiCt in the tank will cause premature tank failure. In some water areas, you may not be able to drain all sediment deposits by simply draining the tank. In these cases Mag Erad (part no. 23600) can be used to help remove[...]

  • Page 26

    Service and Adjustment (cont'd) L.P. Gas Control Valve & Burner Assembly Replacement Information Draining The water heater should be drained if being shut down during freezing temperatures. Also periodic draining and cleaning of sediment from the tank may be necessary. AWARNING PROPANE (L.P.) GAS CONTROL VALVE AN BURNER ASSEMBLY REPLACEMEN[...]

  • Page 27

    Service and Adjustment (cont'd) Drain Valve Washer Replacement NOTE: For replacement, use a _z" x '_/_"x ¼" thick washer available at your nearest hardware store. For ordering replace- ment washers, refer to the "Repair Parts" section. Turn "OFF" gas supply to water heater. Follow "Draining" i[...]

  • Page 28

    Troubleshooting Guide Start Up Conditions THERMAL EXPANSION Water supply systems may, because of such events as high line pressure, frequent cut-offs, the effects of water hammer among others, have installed devices such as pressure reducing valves, check valves, back flowpreventers, etc...to control these types of problems. When these devices are [...]

  • Page 29

    Troubleshooting Guide (cont'd) CONDENSATION Whenever the water heater is filled with cold water, a certain amount of condensation will fornt while the burner is on. A water heater may appear to he leakingwhen in fact the water is condensation. This usually happens when: • When a new water heater is filled with cold water for the first time. [...]

  • Page 30

    Troubleshooting Guide (cont'd) Operational Conditions (cont'd) "AIR" IN HOT WATER FAUCETS WATER IS TOO HOT AWARNING HYDROGEN GAS: Hydrogen gas can be produced in a hot water system that has not been used for a long period of time (generally two weeks or more). Hydrogen gas is extremely flammable and explosive. To prevent the pos[...]

  • Page 31

    Troubleshooting Guide (cont'd) Leakage Checkpoints Use this guide to check a "Leaking" water heater. Many suspect- ed "Leakers" are not leaking tanks. Often the source of the water can be found and corrected. If you are not thoroughly familiar with your local gas codes your water heater, and safety practices, contact the S_[...]

  • Page 32

    Troubleshooting Guide (cont'd) _IWARNING I This troubleshooting guide has been supplied for use by quail- I tied service personnel who have a complete understanding of beth e ectric ty and gas. _ICAUTION I Label all wiring before disconnecting any wiring; to ensure correct reconnection. Failure to follow this instruction I could cause improper[...]

  • Page 33

    Troubleshooting Guide (cont'd) Diagram for Electrical System Check on pages 34 and 35. 120V ONIOFF SWITCH, GAS PRESSURE SWITCH @ 120V GAS SOLENOID HI-LIMIT N._ sw_c...,c AIR PRESSURE SWITCH INDICATOR LIGHT 120V 0 NC AIR PRESSURE SWITCH (_ GROUND iv R= ACK ] I I I [ ®-..._ MANUAL HI- LIMIT SWITCH '! "-----® WHITE 120V GAS SOLENOID o[...]

  • Page 34

    Troubleshooting Guide (cont'd) ELECTRICAL SYSTEM CHECK (Use diagram on page 33) _,CAUTION I Label all wiring before disconnecting an)" wiring; to ensure correct reconnection. Failure to follow this instruction I could cause improper and possible dangerous operation, I I resulting in DEATH, SERIOUS BODILY INJURY, OR I t PROPERTY DAMAGE. ] [...]

  • Page 35

    Troubleshooting Guide (cont'd) Check #5 to ground for 110/120 L.__ VO rs. I- Yes Check#9 for 110/120 volts. I No Yes Check venting manual reset switch. continued from facing page _o -t_hec_#_togrouod/r110,_20_o,ts. I-.-_o t Isindicator,_htoo? I I Yes Y I Replace indicator light. Secure air pressure line. Replace air pressure switch. Yes b t ls[...]

  • Page 36

    Parts Order List POWER MISER TM 9 POWER VENT GAS WATER HEATERS MODEL NUMBERS: 153.335816 153.335845 153.335862 153.335916 153.335942 153.335962 40 Gal. 40 Gal. High Altitude L.P. 40 Gal. L.E 5O Gal. 50 Gal. High Altitude LP. 50 Gal. L.P. 3 4 5 32 1 I 36[...]

  • Page 37

    Parts Order List (cont'd) POWER MISER TM 9 POWER VENT GAS WATER HEATERS MODEL NUMBERS: 153.335816 40 Gal. 153.335845 40 Gal. High Altitude L.E 153.335862 40 Gal. L.E 153.335916 50 Gal. 153.335942 50 Gal. High Altitude L.E 153.335962 50 Gal. L.E KEY NO. PART DESCRIPTION 1. Vent Cap w/Screen 9002120 9002120 2. Wall Collar 9001993 9001993 3. 5&ap[...]

  • Page 38

    Parts Order List POWER MISER TM 9 POWER VENT GAS WATER HEATERS MODEL NUMBERS: 153.335816 40 Gal. 153.335845 40 Gal. High Altitude L.P. 153.335862 40 Gal. L.P. 153.335916 50 Gal. 153.335942 50 Gal. High Altitude L.P. 153.335962 50 Gal. L.P. 3 4 5 P 31€._ 14 ] I 38[...]

  • Page 39

    Parts Order List (cont'd) POWER MISER TM 9 POWER VENT GAS WATER HEATERS MODEL NUMBERS: 153.335816 40 Gal. 153.335845 40 Gal. High Altitude L.P. 153.335862 40 Gal. L.P. 153.335916 50 Gal. 153.335942 50 Gal. High Altitude L.R 153.335962 50 Gal. L.P. KEY NO. PART DESCRIPTION 24. Thermostat Adjustment Knob 25. Gas Thermostat (Nat.) 25. Gas Thermos[...]

  • Page 40

    Warranty About Your Warranty THE PRICE OF YOUR WATER HEATER DOES NOT INCLUDE A FREE CHECKUP SERVICE CALL. On Water Heater Installations Arranged By Sears, Sears warrants the installation. ON INSTALLATIONS NOT MADE BY SEARS AUTHORIZED CONTRACTORS: 1. Your Sears warranty applies to the product only. 2. Sears does not warrant the installation. 3. A ch[...]