English dropdown-ico

Kraftware Corporation DS-16M2 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Kraftware Corporation DS-16M2, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Kraftware Corporation DS-16M2 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Kraftware Corporation DS-16M2. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Kraftware Corporation DS-16M2 should contain:
- informations concerning technical data of Kraftware Corporation DS-16M2
- name of the manufacturer and a year of construction of the Kraftware Corporation DS-16M2 item
- rules of operation, control and maintenance of the Kraftware Corporation DS-16M2 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Kraftware Corporation DS-16M2 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Kraftware Corporation DS-16M2, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Kraftware Corporation service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Kraftware Corporation DS-16M2.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Kraftware Corporation DS-16M2 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    1 This document explains the power , cooling, w eight, and rack placemen t requirements for the EMC departmental switch es listed below . It also describes the kits available for m ounting them in EMC and non- EMC racks and incl udes insta llation instruction s as well. Major s ection s are • Device Power , Cooling, and W eight Information ......[...]

  • Page 2

    2 EMC Depar tmen tal Switches DS-16M 2 and DS-32 M2 Installatio n Guide Device P ow er , Cooling, and W eight Inf ormation De vice P o w er , Co oling, and W eight Information De vice Di mensions De vice P lacement Re quirements The DS-16M2 switches must be located at the top of the rack/cabinet, because the power cor d routing for these switches r[...]

  • Page 3

    EMC Depar tm ental Switches DS-16M2 and DS -32M2 Install ation Guide 3 Switch Mounting Kit (DS-16M or DS-32M) Switch Mounting Kit (DS-1 6M or DS-32M) The DS1 6- and DS32- CRKH kits cont ain the 16- or 32-po rt st andar d swi tch rail moun ting k its, and the DS16 - and DS32 - CRKL kits cont ain t he 16- or 32-port low protru sion rai l mounting kit[...]

  • Page 4

    4 EMC Depar tmen tal Switches DS-16M 2 and DS-32 M2 Installatio n Guide Switch Mounting Kit (DS-16M or DS-32M) T oo ls Required f or Ins tallat ion Y ou will n eed to have the foll owing tool s available to com plete the installatio n of the rails an d switch(es). ◆ # 1 Phillip s head screwdriver ◆ 1/4-i n. nut driver ◆ 5/16-i n. nut drive r [...]

  • Page 5

    EMC Depar tm ental Switches DS-16M2 and DS -32M2 Install ation Guide 5 Installing the DS-16M and DS-32M Rails Installing the DS-16M and DS-32M Rails This secti on describes the install ation procedures for the D S-16M an d DS-32M ra ils. The fig ures bel ow show a fro nt and r ear view of four sets of rails ins talled in a 39U rack. Note that the r[...]

  • Page 6

    6 EMC Depar tmen tal Switches DS-16M 2 and DS-32 M2 Installatio n Guide Installing the DS-16M and DS-32M Ra ils DS-16M Rails Installatio n There are two dif f er ent length rails: The short rails range between 20.5 inches to 27 inches. The long rails range fr o m 27 inches to 34 inches. Each kit contains two diff er ent length r ear rail mounts. Us[...]

  • Page 7

    EMC Depar tm ental Switches DS-16M2 and DS -32M2 Install ation Guide 7 Installing the DS-16M and DS-32M Rails 1. Assemble the rails. The rails assembl y consis ts of an adjust able rai l, a C cha nnel, and two washers and kep nuts. See the figure below . a. Ins ert the t hread ed p ost s on th e C channel in to the slot on th e adjustable ra il. b.[...]

  • Page 8

    8 EMC Depar tmen tal Switches DS-16M 2 and DS-32 M2 Installatio n Guide Installing the DS-16M and DS-32M Ra ils 3. Adjust the length o f the rail to fit between the channels in the rack/cabinet. NOTE: The rail flanges go to the in side of the channels. 4. Once the rails ar e adjusted to the correct length, tighten the kep nuts on the rai l assembly[...]

  • Page 9

    EMC Depar tm ental Switches DS-16M2 and DS -32M2 Install ation Guide 9 Installing the DS-16M and DS-32M Rails M5 x 16 mm flat head screw s (see the table on page 3 ). Leave the screws finger-tight, and tighten them after the switch is installed. See the figur e below . If you ar e installing the switch in a 40U cabinet , install a key plate s pacer[...]

  • Page 10

    10 EMC Depar tmen tal Switches DS-16M 2 and DS-32 M2 Installatio n Guide Installing the DS-16M and DS-32M Ra ils 7. If you are installing the switch in a 39U cabinet, position t he #10 washer and ball stud in the center hole, between the two M5 x 12 mm screws. Hand- tighten the ball stu d. NOTE: The ball studs s upport th e bezel. If you are instal[...]

  • Page 11

    EMC Depar tm ental Switches DS-16M2 and DS -32M2 Install ation Guide 11 Installing the DS-16M and DS-32M Rails 9. Se cure t he rail t o a r ound-hol e r ear channel with 2 M5 x 12 mm pan-head scr ews (see the table on page 3), or secur e the rail to a sq u a re - ho l e re ar c h an n e l w i t h 2 s q u are - h o le w a s h er s an d M5 x 16 mm fl[...]

  • Page 12

    12 EMC Depar tmen tal Switches DS-16M 2 and DS-32 M2 Installatio n Guide Installing the DS-16M and DS-32M Ra ils DS-32M Rails Installatio n There are two dif ferent length rails: the short rails range fr om 20.5 inches to 27 inches. The long rails range fro m 27 inches to 34 inches. Each kit contains two differ ent length rear rail mounts. Use the [...]

  • Page 13

    EMC Depar tm ental Switches DS-16M2 and DS -32M2 Install ation Guide 13 Installing the DS-16M and DS-32M Rails Select the appropriate length rails, and follo w the steps below to install th em. 1. Assemble the rails. The rails assembl y consis ts of an adjust able rai l, a C cha nnel, and two washers and nuts. See the figure be low . a. Ins ert the[...]

  • Page 14

    14 EMC Depar tmen tal Switches DS-16M 2 and DS-32 M2 Installatio n Guide Installing the DS-16M and DS-32M Ra ils 3. Adjust the length o f the rail to fit between the channels in the rack/cabinet. NOTE: The rail flanges go to the in side of the channels. 4. Once the rails ar e adjusted to the correct length, tighten the kep nuts. NOTE: If the side s[...]

  • Page 15

    EMC Depar tm ental Switches DS-16M2 and DS -32M2 Install ation Guide 15 Installing the DS-16M and DS-32M Rails If you are installing the switch in a 40U cabinet , use the appr opriate screws to install the latch bracket (ins tead of the ball stud) to the outside edge of the channel a s you secure the rail. T o attach the bottom lat ch bracke t scre[...]

  • Page 16

    16 EMC Depar tmen tal Switches DS-16M 2 and DS-32 M2 Installatio n Guide Installing the DS-16M and DS-32M Ra ils 8. Secure the rail to a round-hole rear channe l with two M 5 x 12 mm scre ws (see the table on page 3), or secur e the rail to a square-h ole r ear channe l wi th two s quar e- hole wa shers an d M5 x 16 mm scre ws (see the table on pag[...]

  • Page 17

    EMC Depar tm ental Switches DS-16M2 and DS -32M2 Install ation Guide 17 Installing the DS-16M2 an d DS-32M2 Switches Installing the DS-16M2 and DS-32M2 Switc hes This section describes the pr ocedur es for installing the DS-16M2 an d DS-32M2 sw itches in a rack/cabin et, including attachin g the brackets on the switch. Both switches are installed i[...]

  • Page 18

    18 EMC Depar tmen tal Switches DS-16M 2 and DS-32 M2 Installatio n Guide Installing the DS-16M2 an d DS-32M2 Switches CAUTION ! The kits incl ude two (2) sets of screws. T o avoid d amaging the screw holes, be sure to check the labe ling on the bag s and use the appropriate se t of screws for your chassis. The chassi s product number is locat ed on[...]

  • Page 19

    EMC Depar tm ental Switches DS-16M2 and DS -32M2 Install ation Guide 19 Installing the DS-16M2 an d DS-32M2 Switches 5. Push the switch further into the rack/cabinet un til the hole in th e front part of each bracket (the “L”-sh aped end) aligns w ith the hole on the fixed rail. See the figure below . 6. T ighten the front screws securing the r[...]

  • Page 20

    20 EMC Depar tmen tal Switches DS-16M 2 and DS-32 M2 Installatio n Guide Installing the DS-16M2 an d DS-32M2 Switches 8. Install the bez el by positioni ng and insta lling the b ezel stud receptacles on the back of the bezel over the ball studs (39U rack) or latch brackets (40U rack) on the rail ends. 9. Push the bezel onto th e ball studs or latch[...]

  • Page 21

    EMC Depar tm ental Switches DS-16M2 and DS -32M2 Install ation Guide 21 Installing the DS-16M2 an d DS-32M2 Switches NOTE: There is a 3-inch space between the front of the switch and the back of the bezel. Thi s is enough room t o loop the co rd up with out pu shing th e bezel off. 12. Wh en installin g the DS-32M 2 switch, th e 2U spacing all ows [...]

  • Page 22

    22 EMC Depar tmen tal Switches DS-16M 2 and DS-32 M2 Installatio n Guide Installing the DS-16M2 an d DS-32M2 Switches CAUTION ! If you are removing the switche s from the cabi net, you mus t remove the to p switch fr om the back of the cabinet . Y ou can remove all switches be low the top switch from the front. 15. Attach the fibre-optic cables to [...]