KTM 990 SUPER DUKE, 990 SUPER DUKE R manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92

Go to page of

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of KTM 990 SUPER DUKE, 990 SUPER DUKE R, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of KTM 990 SUPER DUKE, 990 SUPER DUKE R one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of KTM 990 SUPER DUKE, 990 SUPER DUKE R. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of KTM 990 SUPER DUKE, 990 SUPER DUKE R should contain:
- informations concerning technical data of KTM 990 SUPER DUKE, 990 SUPER DUKE R
- name of the manufacturer and a year of construction of the KTM 990 SUPER DUKE, 990 SUPER DUKE R item
- rules of operation, control and maintenance of the KTM 990 SUPER DUKE, 990 SUPER DUKE R item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of KTM 990 SUPER DUKE, 990 SUPER DUKE R alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of KTM 990 SUPER DUKE, 990 SUPER DUKE R, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the KTM service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of KTM 990 SUPER DUKE, 990 SUPER DUKE R.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the KTM 990 SUPER DUKE, 990 SUPER DUKE R item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    990 SUPER DUKE 990 SUPER DUKE R KTM Sportmotorcycle AG A–5230 Mattighofen www.ktm.at 11/2006 FOTO: MITTERBAUER KTM Group Partner ART. NR. 3.211.151 EN OWNER’S MANUAL 2007[...]

  • Page 2

    INTRODUCTION » All information contained is without obligation. KTM-Sportmotorcycle AG particularly reserves the right to modify any equipment, technical specifications, prices, colors, shapes, materials, services, service work, constructions, equipment and the like so as to adapt them to local conditions or to cancel any of the above items, all w[...]

  • Page 3

    IMPORTANT INFORMATION » INTENDED PURPOSE The 990 Super Duke is designed to resist the usual wear and tear of paved roads but is not designed for race courses or off-road use. The 990 Super Duke R is designed to resist the usual wear and tear of paved roads or race courses but is not designed for off-road use. OWNER'S MANUAL Carefully read the[...]

  • Page 4

    IMPORTANT INFORMATION » W ARRANTY The service work specified in the „Lubrication and Maintenance Schedule“ must be performed by an authorized KTM workshop. This is the only place that has the qualified technicians and the special tools required for the 990 Super Duke / R. Be sure to have the workshop verify all service work carried out in the [...]

  • Page 5

    INDEX » 4 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 IMPOR T ANT INFORMA TION . . . . . . . . . . . . . . . . . . . . . . . . . .2 SERIAL NUMBER LOCA TIONS . . . . . . . . . . . . . . . . . . . . . . . .6 Chassis number , T ype label . . . . . . . . . . . . . . . . . . . . . . . . .6 Engine number , engine ty[...]

  • Page 6

    INDEX » 5 Checking the front brake pads . . . . . . . . . . . . . . . . . . . . .45 Checking the rear brake fluid level . . . . . . . . . . . . . . . . . .46 Checking the rear brake pads . . . . . . . . . . . . . . . . . . . . . .46 Dismounting and remounting the front wheel . . . . . . . . . .48 Dismounting and mounting the rear wheel . . . . . .[...]

  • Page 7

    Chassis number, Type label The chassis number is stamped on the right side of the steering head tube. Enter this num- ber in the field on page no 1. The type label is located on the right frame tube under the seat. Engine number, engine type The engine number and the engine type are stamped into the left side of the engine below the engine sprocket[...]

  • Page 8

    Clutch lever The clutch lever [1] is fitted on the left hand side of the handle bar . The adjusting screw [A] is used to change the original position of the clutch lever (see maintenance work on chas- sis and engine). The clutch is hydraulically actuated and adjusts itself automatically . Hand brake lever The hand brake lever [2] is mounted on the [...]

  • Page 9

    OPERATION INSTRUMENTS » 8 1 2 Combined instrument The combined instrument is divided into 4 parts. Function buttons: to select the display modes and basic settings in the display T achometer: displays the engine speed Indicator lamps: provide additional information on the motorcycle operating condition Display: shows the speed, cooling liquid temp[...]

  • Page 10

    OPERATION INSTRUMENTS » 9 1 2 3 SPEED [1] The speed can be displayed in kilometers per hour (km/h) or miles per hour (mph). CHANGING THE SPEED DISPLA Y FROM KM/H - MPH or MPH - KM/H Switch on the ignition and press the MODE button more than 10 seconds in the ODO mode. CLOCK [2] The dots between the hours and minutes will blink in the CLOCK display[...]

  • Page 11

    OPERATION INSTRUMENTS » 10 1 2 FROST W ARNING [1] The frost symbol will start to blink regardless of the mode if the ambient temperature drops below 3°C (37.5°F). ODO [2] Displays the total kilometers or miles traveled. This figure will not be cleared if the battery is disconnected.[...]

  • Page 12

    OPERATION INSTRUMENTS » 11 3 2 1 TRIP 1 [1] The trip meter 1 is always active and counts up to 999.9. It is used to measure the length of the trip or the distance between 2 refueling stops. TO RESET TRIP 1 T o reset the trip meter 1 to zero, switch on the ignition, select the TRIP 1 display mode and press the SET button more than 2 seconds. Press [...]

  • Page 13

    Tachometer The tachometer [3] shows the engine speed in revolutions per minute. Do not run the engine beyond the orange mark at 9500 rpm. The speed limiter will set in at 9600 rpm, drastically reducing the engine power above this rotational speed. Cooling liquid temperature display The temperature display [1] is shown in 12 bars. The more bars that[...]

  • Page 14

    Indicator lamps The green indicator lamp will blink in the blinker rhythm when the blinker is switched on. NOTE: The indicator lamp will blink slower when a blinker is broken. The green indicator lamp will light up when the gearbox is in an idling position. The blue indicator lamp will light up when the high beams are switched on. The red warning l[...]

  • Page 15

    Ignition lock The ignition lock has 3 switching positions. Ignition off, (engine can't be started) Ignition on, (engine can be started) Ignition off, handlebar blocked T o switch the ignition to position turn the ignition key to position and firmly press it into the lock. T urn the handlebar to the left, then turn the ignition key to the left.[...]

  • Page 16

    Starter tip switch, Emergency OFF tip switch The emergency off switch [1] is provided for emergency situations and should not be used to switch off the engine. The engine is ready for operation in position (ignition circuit and starter circuit are switched on). The engine cannot be started in position (ignition circuit and starter circuit are inter[...]

  • Page 17

    Seat lock, removing the seat The seat lock [1] can be locked with the ignition key . T o remove the seat, insert the ignition key and turn 90° in a clockwise direction. Lift the seat in the back while pressing near the holding strap and pull off towards the back. T o mount the seat, place it on the motorcycle and position the hooks [2] on the bott[...]

  • Page 18

    Tool set The tool set [1] is located in the storage compartment under the seat. Helmet lock The steel rope [2] in the tool bag can be used to secure a helmet. T o secure, remove the seat, run the rope through the helmet, attach both ends to the hook [3] and mount the seat. The helmet lock is provided to secure the helmet to the motorcycle when park[...]

  • Page 19

    Shift lever The shift lever is mounted on the left side of the engine. The position of the gears is shown in the illustration. Neutral, or the idle speed, is located between first and second gear . The basic position of the shift lever can be adjusted according to your seating position (see Maintenance work). Side stand Fold the side stand [1] forw[...]

  • Page 20

    Footrests The passenger footrests [1] fold up. Compression damping of fork The fork's damping action during compression travel (compression damping) can be adjusted. This allows you adjust the damping behavior to match your driving style and the payload. The adjusting screws [2] are located on the fork leg axle passage. More information is pro[...]

  • Page 21

    Spring preload of the fork The fork's preload can be adjusted by means of the adjusting screws [1] . More information is provided in the chapter „Adjusting the fork and shock absorber“. Damping action during compression of shock absorber The shock absorber's damping action during compression travel (compression damping) can be adjuste[...]

  • Page 22

    Rebound damping of shock absorber The shock absorber's damping action during rebound travel (rebound damping) can also be adjusted. This allows you adjust the damping behavior to match your driving style and the payload. The adjusting screw [1] is located on the bottom of the shock absorber . More information is provided in the chapter "A[...]

  • Page 23

    Instructions for initial operation – Make sure the work for the „pre-delivery inspection“ was performed by your author- ized KTM workshop. The DELIVERY CER- TIFICA TE and SERVICE MANUAL will be handed over when you pick up your vehicle. – Read these operating instructions care- fully before your first ride. – Enter the chassis, engine and[...]

  • Page 24

    – The tires must be designed for a speed of over 240 KPH (speed symbol ZR) and must be released by KTM. – New tires have a smooth surface, which means that they must be run in to achieve full grip. For this purpose, ride the motor- cycle carefully at moderate speed during the first 200 kilometers with new tires, tilting the vehicle at different[...]

  • Page 25

    Check the following before each start When you start, the motorcycle must be in perfect mechanical condition. For safety reasons, you should make a habit of performing an overall check of your motorcycle before each start. The following checks should be performed: 1 FUEL Check the fuel quantity in the tanks. 2 CHAIN Check the tension and condition [...]

  • Page 26

    6 COOLING FLUID Check the level of cooling fluid when the engine is cold. 7 ELECTRICAL SYSTEM Start the engine and check the headlight, tail lamp, brake light, turn signals, indicator lamps, horn and emergency-off switch for proper functioning. 8 CHECK OIL LEVEL Insufficient oil results in premature wear and consequently to engine damage. 9 BAGGAGE[...]

  • Page 27

    Starting the engine 1 Switch on emergency OFF switch [1] . 2 Switch on ignition (turn ignition key [2] into position ). NOTE: Y ou will hear the operation of the fuel pump for approx. 2 seconds after switching on the ignition. The FI indicator lamp will also light up during this time and the engine can- not be started. 3 Switch transmission to idle[...]

  • Page 28

    IF THE ENGINE IS DOES NOT CRANK WHEN YOU ACTUA TE THE ST ARTER TIP SWITCH: – whether you accelerated while starting – the transmission is switched to idle – Check if the emergency OFF switch is on – Check if the ignition is on – the headlight is on – If this is not the case, the battery is dis- charged – If the lights are on, proceed [...]

  • Page 29

    – While riding your motorcycle, never switch the ignition lock to positions and . – Do not try to change the settingsof the combined instrument while driving. Y our attention will be distracted from the traf- fic and this may cause you to lose con- trol of your motorcycle. – The frost symbol * in the combined instru- ment will start to blink [...]

  • Page 30

    DRIVING INSTRUCTIONS » 29 – On salt-sprayed or dirty roads brake action may be delayed as well. First, the brakes must be braked clean. – Remember that the stopping distance will be longer if you are carrying a pas- senger or baggage. – When you brake, the brake discs, brake pads, brake caliper and brake fluid heat up. The hotter these parts[...]

  • Page 31

    Fuel In the condition at delivery , the LC8 engine requires unleaded fuel with at least RON 95 (USA = Premium PON 91, see technical specifications – engine). After refueling, it will take approx. 3 minutes for the fuel warning lamp to switch off and for TRIP F to automatically reset to 0 and return to the previous display mode. NOTE: Press the SE[...]

  • Page 32

    31[...]

  • Page 33

    PERIODIC MAINTENANCE SCHEDULE » 990 SUPER DUKE / R 2007 A clean motorcycle can be checked more quickly which saves money! 1st Service after 1000 km every 7500 km or once a year every 15000 km or every 2 years ENGINE Change engine oil and oil filter zzz Clean oil screens of engine and oil tank zzz Clean magnetic drain plugs of engine and oil tank z[...]

  • Page 34

    PERIODIC MAINTENANCE SCHEDULE » 990 SUPER DUKE / R 2007 A clean motorcycle can be checked more quickly which saves money! 1st Service after 1000 km every 7500 km or once a year every 15000 km or every 2 years ADD-ON-PARTS Replace the graphite gasket in the rear exhaust manifold slide z Check actuating cables for damage, smooth operation, and kink-[...]

  • Page 35

    PERIODIC MAINTENANCE SCHEDULE » 34 IF MOTORCYCLE IS USED FOR COMPETITION 7500 KM SERVICE SHOULD BE CARRIED OUT AFTER EVER Y RACE! Service intervalls should never be exceeded by more than 500 km. Maintenance work performed by an authorized KTM workshop is not a substitute for care and maintenance by the driver! 990 SUPER DUKE / R 2007 A clean motor[...]

  • Page 36

    PERIODIC MAINTENANCE SCHEDULE » 990 SUPER DUKE / R 2007 VITAL CHECKS AND CARE PROCEDURES TO CONDUCTED BY THE OWNER OR THE MECHANIC before each start after every cleaning every 1000 km Check oil level z Check brake fluid level z Check brake pads for wear z Check lighting system for proper operation z Check horn for proper operation z Lubricate actu[...]

  • Page 37

    – Do not clean the motorcycle with a power washer otherwise water will get into the bearings, electric socket connectors, etc. – Use special KTM screws with the correct thread length to fasten the spoiler to the tank. Mounting other screws or longer screws could puncture the tank and cause fuel to leak out. – If you disconnect socket connecto[...]

  • Page 38

    Adjusting the fork and shock absorber There are a number of ways to adjust the fork and shock absorber to match the chassis to your driving style and the payload. W e have provided a table with pragmatical values to help you tune up your motorcycle. These tune-up specifications are reference values only and should serve as a basis for your per- son[...]

  • Page 39

    Adjusting the spring preload on the fork The fork spring preload can be adjusted by turning the adjusting screws [2] (wrench size 24 mm) ± 5 mm (0,2 in). T urning in a clockwise direction will increase the preload, turning in a counterclockwise direc- tion will decrease the preload. 1 turn will change the preload by 1 mm. Changing the preload will[...]

  • Page 40

    ST ANDARD ADJUSTMENT LOW -SPEED: – T urn adjusting screw [1] clockwise as far as it will go. – T urn 20 clicks in a counterclockwise direction. ST ANDARD ADJUSTMENT HIGH-SPEED: – T urn adjusting screw (wrench size 17 mm) clockwise as far as it will go. – Super Duke: T urn 1.5 turns in a counterclockwise direction. – Super Duke R: T urn 2.[...]

  • Page 41

    Checking the chain tension Place the motorcycle on the side stand. Switch the transmission to neutral and push the chain up. The distance between the chain and the swing arm should be 7 mm when the upper part of the chain [1] is tensioned (see drawing). Correct the chain tension if necessary . – If chain tension is too great, parts within the sec[...]

  • Page 42

    Chain maintenance Maintenance of the X-ring chain is reduced to a minimum. Rinse off any heavy dirt with plenty of water . Residual used grease must be removed prior to lubrication (Motorex Chain Clean 611). After drying, use a chain spray specially designed for X-ring chains (Motorex Chainlube 622). – No lubrication is allowed to reach the rear [...]

  • Page 43

    General information on KTM disk brakes BRAKE CALIPERS: The front brake calipers [1] have 4 brake pistons and are radially bolted to the fork legs. The front brake disks are designed as „floating“ brake disks, i.e. they are not firmly con- nected to the front wheel. The lateral balance ensures that the brake pads always have the best possible co[...]

  • Page 44

    BRAKE FLUID: W e recommend that you use Motorex DOT 5.1 brake fluid when you refill or change the brake fluid. DOT 5. 1 brake fluid has a wet boiling point of 180°C / 356°F (25°C / 45°F higher than DOT 4) and is safer for high performance applications. Brake fluid DOT 5.1 is a poly- ethylene glycol based fluid, amber -colored and can be mixed w[...]

  • Page 45

    Adjusting the basic position of the hand brake lever The basic position of the hand brake lever can be modified by turning the adjusting screw [1] . This lets you adapt the position of the pressure point (the resistance you feel on the hand brake lever when the brake pads are pressed against the brake disk) to fit any hand. At the hand brake lever [...]

  • Page 46

    Checking the front brake pads The brake pads can be inspected from the rear . The linings must be at least 1 mm (0.04 in) thick. At their most worn point brake pad linings should not be thinner than 1 mm, otherwise they could lead to brake failure. For your own safety don’t put off having your brake pads changed. If the brake pads are replaced to[...]

  • Page 47

    Checking the rear brake pads The brake pads can be inspected from the rear . The thickness of the linings may not be less than 1 mm (0.04 in). At their most worn point brake pad linings should not be thinner than 1 mm, otherwise they could lead to brake failure. For your own safety don’t put off having your brake pads changed. If the brake pads a[...]

  • Page 48

    47[...]

  • Page 49

    MAINTENANCE WORK ON CHASSIS AND ENGINE » 48 2 3 3 2 1 6 Dismounting and remounting the front wheel Special stands are required to dismount the wheels to make sure the motorcycle is securely fixed. The front stand only adequately fixes the motorcycle together with the rear stand. The stands shown in the illustration can be found in the KTM Power Pa[...]

  • Page 50

    MAINTENANCE WORK ON CHASSIS AND ENGINE » 49 4 A 5 B C C T ake the left [4] and right distance bushing out of the shaft seal rings. – Do not operate the hand brake when the front wheel has been dismounted. – Be careful not to damage the brake disks when you lay the front wheel down. Before you remount the front wheel, clean and grease the shaft[...]

  • Page 51

    Dismounting and mounting the rear wheel Special stands are required to dismount the wheels to make sure the motorcycle is securely fixed. The stands shown in the illustration can be found in the KTM Power Parts catalog. Mount the rear stand. Make sure the stand rests on solid ground and is correctly mounted. The rear wheel should not touch the grou[...]

  • Page 52

    – If you don’t happen to have a torque wrench at hand, make sure you have the tighten- ing torque corrected by a KTM dealer as soon as possible. A loose wheel spindle may lead to an unstable driving behavior of your motorcycle. – After mounting the rear wheel, keep operating the footbrake until the pressure point returns. – It is very impor[...]

  • Page 53

    Battery The battery is located in the front spoiler in front of the engine and is maintenance-free. It is not necessary to check the electrolyte level or to refill water . Simply keep the battery poles clean and slightly grease them with an acid-free grease if necessary . The charge condition and type of charge are very important for the battery&ap[...]

  • Page 54

    Removing and remounting the battery The battery only needs to be removed if the motorcycle is being immobilized. Remove the screws [1] on both sides, loosen the screws [2] 2 turns and remove the front spoiler towards the front. Push the cables to the side. Remove the screws [3] and fold the battery cover [4] down. First disconnect the negative term[...]

  • Page 55

    MAINTENANCE WORK ON CHASSIS AND ENGINE » 54 VOL T 1 Charging the battery The battery discharges every day , even if it is not used. Always disconnect the battery when charging. Charge the battery as described in the instruc- tions [1] on the battery housing. Do not exceed the amperage and charging time. Quick charg- ing at a high amperage has an a[...]

  • Page 56

    Main fuse The main fuse protects all of the motorcycle's electric power consumers. The main fuse is located on the left under the front spoiler . Pull the connector [1] out of the bracket, remove the cap [2] and check the main fuse [3] . A spare fuse [4] (30 amperes)is also plugged into the bracket. Always replace blown fuses with an equivalen[...]

  • Page 57

    Fuses for individual power consumers A fuse box is mounted under the seat containing additional fuses that protect the individ- ual electric power consumers. The power consumers are listed numerically on the cover of the fuse box [1] and allocated as described below . Spare fuses [2] with 10 and 15 amperes are also found in the fuse box. NO CONSUME[...]

  • Page 58

    Replacing the headlight lamp Remove the screws [1] on the left and right and tilt the headlight mask down towards the front. Never touch the glass of the bulb with your fingers. The glass of the bulb must remain absolutely free from grease. Heat will otherwise cause the grease to evaporate and settle down on the reflector . BULB FOR HIGH BEAM [A] :[...]

  • Page 59

    Adjusting the headlight range The payload can make it necessary to correct the headlight range. The headlight range can be adjusted with the adjusting screw [1] . T urning in a clockwise direction will increase the headlight range, turning in a counterclockwise direction will reduce the headlight range. CONTROL: Make a mark on a light colored wall [...]

  • Page 60

    BULB FOR THE T AILLIGHT : Remove the bulb socket [2] from the housing and pull the bulb out of the socket. Insert a new bulb and press the bulb socket all the way into the taillight housing. Mount the seat. MAINTENANCE WORK ON CHASSIS AND ENGINE » 59 Replacing the brake light and taillight bulbs NOTE: Only mount red light bulbs in a smoked brake t[...]

  • Page 61

    Cooling system The water pump in the engine ensures a forced circulation of the cooling liquid. When the engine is cold, the cooling liquid only circulates in the cylinders and cylinder heads. The thermostat will open when the engine reaches approx. 75°C (167°F) and the cooling liquid will also be pumped through the aluminum radiator . Cooling is[...]

  • Page 62

    A mixture of 50% antifreeze and 50% distilled water is used as the cooling liquid. How- ever , the anti-freeze protection must be at least -25° C (-13° F). Aside from antifreezing pro- tection, this mixture also provides great corrosion protection which is why it must not be replaced by pure water . – For the cooling system, use only high-grade[...]

  • Page 63

    Checking the cooling liquid level in the radiator Hold the radiator cap [1] with a cloth, carefully turn in a counterclockwise direction and remove. The radiator should be completely filled with cooling liquid; no air should be in the radiator . If any cooling liquid is missing, the cooling system is probably leaking. Have the cooling system checke[...]

  • Page 64

    T o completely bleed the cooling system, the motorcycle must be raised approx. 50 cm (20 in) in the front. Add cooling liquid until it runs out of the vent holes without bubbles and immediately mount the screw to prevent air from entering the radiator . Completely fill the radiator with cooling liquid. Mount the radiator cap and move the motor- cyc[...]

  • Page 65

    Adjusting the handlebar tilt Loosen the screws [2] . Adjust the handlebar and tighten the screws to 20 Nm. Make sure the handlebar instruments do not touch the fuel tank when the handlebar is com- pletely turned. T ilting the handlebar too far back will reduce the steering angle since the handlebar instru- ments will touch the fuel tank If the hand[...]

  • Page 66

    MAINTENANCE WORK ON CHASSIS AND ENGINE » 65 How to change the handlebar position (Super Duke R) The upper triple clamp includes 2 bores arranged at a distance of 15 mm (0.6 in) from one another . Accordingly , you can mount the handlebar in 2 different positions. The steering angle is reduced if the handlebar is mounted in the rear position. Adjus[...]

  • Page 67

    Engine oil Automobile engine oil used to be used for four -stroke motorcycles before there were sepa- rate motorcycle specifications. Different technical developments made it necessary to have a separate specification for four -stroke motorcycles - the JASO T903 MA standard. Whereas car engines require long changing intervals, motorcycle engines re[...]

  • Page 68

    Refilling engine oil T o refill engine oil, take off the right spoiler [1] by removing the screws [2] . Also remove the screws [3] and take off the spoiler . Unscrew the plug [4] and refill engine oil. W ait 20 seconds and check the oil level again. The quantity of oil between the MIN and MAX marks is 0.3 liter . Mount the plug and check the engine[...]

  • Page 69

    Changing the engine oil and the oil filter, cleaning the oil screen Y ou may only change the engine oil yourself after the warranty period has expired. The war- ranty will become void if you change the oil yourself during the warranty period. NOTE: The LC8 engine has a dry-sump lubrication system. The engine oil is pumped from the oil sump in the e[...]

  • Page 70

    Remove the drain plug [6] on the oil tank and allow the oil to drain into a receptacle. Remove the screws [7] and tilt the oil return valve [8] to the side. Carefully pull the oil screen [9] out of the oil tank. Thoroughly clean the drain plugs, the cover and both oil screens. Clean all rubber seal rings and check for damage. Replace if necessary .[...]

  • Page 71

    Mount the oil drain plug on the engine with a new seal ring and tighten to 20 Nm. Slide the oil screen [1] into the guides in the oil pump housing with the TOP mark fac- ing up. Make sure the form ring is in place and mount the cap [2] . T ighten the screws to 10 Nm. Insert a new oil filter [3] in the engine case, grease the O-ring and mount the oi[...]

  • Page 72

    Remove the right spoiler (see Refilling the engine oil) and unscrew the plug [6] . Add 2.5 liters (0.7 USgal) of fully synthetic engine oil meeting the JASO MA standard (e.g. Motorex Power Synt 4T) and remount the plug. Start the engine and allow to run warm in neutral until 4 bars on the temperature indicator light up. Switch off the engine and ch[...]

  • Page 73

    If you have your motorcycle serviced as set forth in this manual, no malfunctioning is to be expected. Nevertheless, if an error does arise, we recommend that you look for the error according to the following chart. Please note that you cannot perform all of the work yourself. If you are not sure, contact your KTM dealer . TROUBLESHOOTING » 72 TRO[...]

  • Page 74

    TROUBLESHOOTING » TROUBLE CAUSE REMEDY Engine cranks but doesn’t start. Operating error Blown fuse for the fuel pump Clutch not attached to the fuel line The plug and socket connector on the wiring harness is oxidized Error in the injection system A gear is engaged and the side stand is folded down Pay attention to starting off information (see [...]

  • Page 75

    TROUBLESHOOTING » 74 TROUBLE CAUSE REMEDY Engine overheats Blown fan fuse Defect fan or thermoswitch for fan Air in the cooling system Replace fuse 5 Contact an authorized KTM workshop. Bleed the cooling system (see Maintenance work) FI lamp is blinking / lights up Error in the injection system V isit an authorized KTM workshop Engine stalls while[...]

  • Page 76

    TROUBLESHOOTING » TROUBLE CAUSE REMEDY The battery is discharged The ignition (power consumer) has- n’t been switched off The battery isn’t charged by the generator Recharge the battery according to the relevant instructions. V oltage regulator and generator should be checked by an authorized KTM workshop. No values are visible in the com- bin[...]

  • Page 77

    TROUBLESHOOTING » 76 BLINK CODE SIGNAL / COMPONENT ERROR DESCRIPTION ENGINE 12 Coolant temperature sensor Output signal too low /high Continues to run 13 Air temperature sensor Output signal too low /high Continues to run 14 Ambient air pressure sensor Output signal too low /high Continues to run 15 T ilt angle sensor Output signal too low /high C[...]

  • Page 78

    CLEANING » 77 Regular cleaning and paintwork care are part of the maintenance work and help to maintain the value of your motorcycle. Never clean the motorcycle with a power washer or a strong water jet, otherwise the pressure will allow water to enter the elec tric compo- nents, plugs, cables, bearings, etc. which can cause malfunctioning or can [...]

  • Page 79

    STORAGE » 78 If you plan to immobilize your motorcycle for a longer period of time, proceed as follows: – Run the tank empty to be able to add fresh fuel when starting up again. – Clean the motorcycle thoroughly (see CLEANING chapter). – Change the engine oil and the oil filter (old engine oil contains aggressive impurities). – Check the q[...]

  • Page 80

    TECHNICAL SPECIFICATIONS – CHASSIS » CHASSIS 990 SUPER DUKE / R 2007 Frame T ubular chrome-molybdenum-steel space frame Fork WP Suspension – U p S ide D own 4860 ROMA Spring travel front 135 mm (5.3 in) Rear suspension WP Suspension 4618 BA VP Spring travel rear Super Duke: 160 mm (6.3 in) Super Duke R: 150 mm (5.9 in) Front brake Disk brake, [...]

  • Page 81

    TECHNICAL SPECIFICATIONS – CHASSIS » CHASSIS 990 SUPER DUKE / R 2007 Battery maintenance-free battery 12V 11.2 Ah Steering head angle Super Duke: 66.1° Super Duke R: 67.3° Wheel base 1450 ± 10 mm (57 ± 0.4 in) Seat height, unloaded Super Duke: 850 mm (33.5 in) Super Duke R: 860 mm (33.9 in) Ground clearance, unloaded Super Duke: 140 mm (5.5 [...]

  • Page 82

    TIGHTENING TORQUES – CHASSIS 2007 Collar bolt on front wheel spindle M24x1.5 60 Nm Collar nut wheel spindle rear M25x1.5 90 Nm AH bolt shock absorber top/bottom M14x1.5 80 Nm Collar nut for swing arm bolt M19x1.5 130 Nm AH bolts on subframe M8 Loctite 243 + 25 Nm AH bolts on back of footrest support M8 Loctite 243 + 25 Nm Engine carrier bolts M10[...]

  • Page 83

    TECHNICAL SPECIFICATIONS – CHASSIS » TIGHTENING TORQUES – CHASSIS 2007 HH bolts for side stand fixture - side stand bracket M10 Loctite 243 + 25 Nm HH bolts for side stand mounting M10 Loctite 243 + 35 Nm HH bolt for spring rest on side stand M8 Loctite 243 + 25 Nm HH bolt for side stand switch M4 Loctite 243 + 2 Nm Drain plug on oil tank M12x[...]

  • Page 84

    TECHNICAL SPECIFICATIONS – ENGINE » ENGINE 990 LC8 2007 Design Liquid-cooled, 2-cylinder 4-stroke engine with 75° V arrangement with balancer shaft and electric starter Displacement 999 cc Bore / Stroke 101/62.4 mm Compression ratio 11.5:1 Fuel unleaded fuel with at least RON 95 (USA: Premium RON 91) * V alve timing 4 valves controlled over buc[...]

  • Page 85

    TECHNICAL SPECIFICATIONS – ENGINE » ENGINE 990 LC8 2007 Ignition system breakerless transistorized electronic ignition system with digital ignition advance Ignition timing Map-controlled via TPS Map-controlled via TPS 12V 450W at 6000 rpm Spark plug NGK IR KR8BI Electrode distance 0.8 mm Cooling system liquid cooled, permanent circulation of coo[...]

  • Page 86

    Accessories and payload . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 Adjusting compression damping of fork . . . . . . . . . . . . . . . . .37 Adjusting rebound damping of fork . . . . . . . . . . . . . . . . . . . .37 Adjusting the basic position of the hand brake lever . . . . . . . .44 Adjusting the fork and shock absorber . . . . .[...]

  • Page 87

    How to change the handlebar position (Super Duke R) . . . . . .65 Ignition lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Important information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Indicator lamps . . . [...]

  • Page 88

    CONSUMER INFORMATION FOR USA ONLY » 87 REPORTING SAFETY DEFECTS If you believe that your vehicle has a defect which could cause an accident resulting in injury or death, you should immediatel y inform the National Highway T raffic Safety Administration (NHTSA) in addition to notifying KTM North America, Inc. If NHTSA receives similar complaints, i[...]

  • Page 89

    CONSUMER INFORMATION FOR USA ONLY » 88 under seat on fuel tank R/S on fuel tank L/S on steering head tube on fuel tank Sticker positions: 345 on frame tube R/S under seat on frame tube R/S 7 on frame tube L/S 6 9 8 2 1[...]

  • Page 90

    CONSUMER INFORMATION FOR USA ONLY » [3] Suspension setting [5] T echnical information [8] Before you go for the first ride [7] V ehicle emission [2] T ype label CAN [6] Noise emission [1] EA VP [4] Chain tension [9] T ype label USA 89[...]

  • Page 91

    USE THIS SPACE FOR NOTES » 90[...]

  • Page 92

    990 SUPER DUKE 990 SUPER DUKE R KTM Sportmotorcycle AG A–5230 Mattighofen www.ktm.at 11/2006 FOTO: MITTERBAUER KTM Group Partner ART. NR. 3.211.151 DE BEDIENUNGSANLEITUNG 2007[...]