Lenovo 3000 J Series manual

User Guide Leno v o 3000 J Series T ypes 7387, 7388, 7389, 7393, 7394, 7395[...]

[...]

Le n o v o 3 000 J Ser ie s[...]

Note Before using this information and the pr oduct it supports, be sure to read the “Important safety information” on page v and Appendix B, “Notices,” on page 73. Fourth Edition (February 2007) © Copyright Lenovo 2005, 2007. Portions © Copyright International Business Machines Corporation 2005. All rights reserved. U.S. GOVERNMENT USERS[...]

Contents Important safety information . . . . . .v Conditions that requir e immediate action . . . . .v General safety guidelines . . . . . . . . . .v i Service and upgrades . . . . . . . . . .v i Static electricity prevention . . . . . . . . vii Power cords and power adapters . . . . . . vii V oltage-selection switch . . . . . . . . .i x Extension[...]

Chapter 8. Getting information, help, and service . . . . . . . . . . . . .6 1 Information resour ces . . . . . . . . . . .6 1 Online Books folder . . . . . . . . . .6 1 Lenovo Care . . . . . . . . . . . . .6 1 Access Help . . . . . . . . . . . . .6 2 W arranty and safety . . . . . . . . . .6 2 www .lenovo.com . . . . . . . . . . .6 2 Help and serv[...]

Important safety information Note Please read important safety information first. This information can help you safely use your desktop or notebook personal computer . Follow and retain all information included with your computer . The information in this document does not alter the terms of your purchase agr eement or the Lenovo ™ Statement of L[...]

In the unlikely event that you notice any of the following conditions, or if you have any safety concerns with your product, stop using the product and unplug it from the power source and telecommunication lines until you can speak to the Customer Support Center for further guidance. See Chapter 8, “Getting information, help, and service,” on p[...]

Danger Hazardous moving parts. Keep fingers and other body parts away . Attention Before replacing any CRUs, turn off the computer and wait three to five minutes to let the computer cool before opening the cover . Static electricity prevention Static electricity , although harmless to you, can seriously damage computer components and options. Impro[...]

The power cords shall be safety appr oved. For Germany , it shall be H05VV -F , 3G, 0.75 mm 2 , or better . For other countries, the suitable types shall be used accordingly . Never wrap a power cord ar ound a power adapter or other object. Doing so can stress the cor d in ways that can cause the cord to fray , crack, or crimp. This can present a s[...]

V oltage-selection switch Some computers are equipped with a voltage-selection switch located near the power-cor d connection point on the computer . If your computer has a voltage-selection switch, ensure that you set the switch to match the voltage available at your electrical outlet. Setting the voltage-selection switch incorrectly can cause per[...]

Be sure that the power outlet you ar e using is properly wir ed, easily accessible, and located close to the equipment. Do not fully extend power cords in a way that will stress the cor ds. Be sure that the power outlet pr ovides the correct voltage and curr ent for the product you ar e installing. Carefully connect and disconnect the equipment fr [...]

become blocked by placing the product on a bed, sofa, carpet, or other flexible surface. Never block, cover , or disable these features. Yo u should inspect your desktop computer for dust accumulation at least once every three months. Befor e inspecting your computer , turn off the power and unplug the computer’s power cord fr om the electrical o[...]

Electrical current safety information Danger Electrical current from power , telephone, and communication cables is hazardous. To avoid a shock hazard: v To prevent possible shock hazard, do not use your computer during a lightning storm. v Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this prod[...]

Perchlorate material: Special handling may apply . See www .dtsc.ca.gov/hazardouswaste/per chlorate. Modem safety information Caution To reduce the risk of fire, use only No. 26 AW G or larger telecommunication line cord. To reduce the risk of fire, electrical shock, or injury when using telephone equipment, always follow basic safety precautions, [...]

Power supply statement Never remove the cover on a power supply or any part that has the following label attached. Hazardous voltage, curr ent, and energy levels ar e present inside any component that has this label attached. There ar e no serviceable parts inside these components. If you suspect a problem with one of these parts, contact a service[...]

Introduction This User Guide contains the following information: v Chapter 1, “Arranging your workspace,” on page 1 provides information about setting up your computer for comfort and the impact of light sources, air circulation, and electrical outlets. v Chapter 2, “Setting up your computer,” on page 3 provides information about setting up[...]

xvi User Guide[...]

Chapter 1. Arranging your workspace To get the most from your computer , arrange both the equipment you use and your work area to suit your needs and the kind of work you do. Y our comfort is of foremost importance, but light sour ces, air circulation, and the location of electrical outlets also can affect the way you arrange your workspace. Comfor[...]

Where it is impossible to avoid r eflections or to adjust the lighting, an antiglare filter placed over the screen might be helpful. However , these filters might affect the clarity of the image on the screen; try them only after you have exhausted other methods of reducing glar e. Dust buildup compounds problems associated with glar e. Remember to[...]

Chapter 2. Setting up your computer Before you begin, make sur e you set up your computer in the best possible work area that suits your needs and the kind of work you do. For mor e information, refer to Chapter 1, “Arranging your workspace,” on page 1. Note: Read “Important safety information” on page v before you set up your computer . Th[...]

If your computer does not have a voltage selection switch, it is designed to operate only at the voltage provided in the country or r egion where it was originally purchased. Continue with step 2. 2. Y our keyboard cable might have a standar d keyboard connector 1 or a Universal Serial Bus (USB) connector 2 . Connect the keyboard cable [...]

v If you have a digital video interface (DVI) monitor , connect the cable to the connector as shown. Note: Y our computer must have an adapter installed that supports the DVI monitor . 5. If you have a modem, connect the modem using the following information. L IN E PHONE P H O N E LINE PHONE LINE PHONE LINE 1 This illustration shows the two [...]

6. If you have audio devices, attach them using the following instructions. For more information about speakers, see steps 7 and 8. 1 Audio line-in This connector receives audio signals fr om an external audio device, such as a stereo system. 2 Audio line-out This connector sends audio signals from the computer to external devices, such[...]

b. Connect the speakers to the computer . 9. Connect any additional devices that you have. Y our computer might not have all connectors that are shown. 1394 1394 1 USB Use this connector to attach a device that requir es a USB connection, such as a keyboard, mouse, scanner , printer , or personal digital assistant (PDA). 2 Serial Use th[...]

10. Connect the power cords to pr operly grounded electrical outlets. Note: Refer to the Access Help online help system for more information about connectors. See “Access Help” on page 62 for instructions on how to open the online help system. 8 User Guide[...]

T urning on power T urn on the monitor and other external devices first, and then turn on the computer . When the power-on self-test (POST) is finished, the logo window closes. If your computer has preinstalled softwar e, the software installation pr ogram starts. If you experience any problems during startup, see Chapter 7, “T roubleshooting and[...]

Updating your operating system Microsoft makes updates available for various operating systems thr ough the Microsoft W indows Update We b site. The We b site automatically determines what W indows updates are available for your specific computer and lists those updates only . Updates could include security fixes, new versions of W indows component[...]

Chapter 3. Installing options This chapter provides an intr oduction to the features and options that ar e available for your computer . Yo u can expand the capabilities of your computer by adding memory , drives, or adapters. When installing an option, use these instructions along with the instructions that come with the option. Important Before y[...]

Microprocessor (varies by model type) v Intel ® Pentium ® 4 processor with HyperThr eading T echnology v Intel Pentium D processor v Intel Celeron ® D processor v Intel Core ™ 2 Duo processor v AMD Athlon 64 processor v AMD Sempron pr ocessor v Internal cache (size varies by model type) Memory v Support for two DDR2 DIMMs v 4 Mb flash memory I[...]

Input/output features v 25-pin, Extended Capabilities Port (ECP)/Extended Parallel Port (EPP) v 9-pin serial connector v Six 4-pin, USB connectors (two on front panel and four on r ear panel) v Standard mouse connector v Standard keyboar d connector v Ethernet connector v VGA monitor connector v Five audio connectors (headphone and microphone on fr[...]

Operating systems, tested for compatibility 1 v Linux ® A vailable options The following are some available options: v External options – Parallel port devices, such as printers and external drives – Serial port devices, such as external modems and digital cameras – Audio devices, such as external speakers for the sound system – USB device[...]

Specifications This section lists the physical specifications for your computer . Dimensions Height: 392 mm (15.43 in.) W idth: 180 mm (7.09 in.) Depth: 445 mm (17.52 in.) W eight Minimum configuration as shipped: 9.1 kg 20.06 lb) Maximum configuration: 10.2 kg (22.5 lb) Environment Air temperatur e: System on: 10° to 35°C (50° to 95° F) System[...]

When you add an option, do not open the static-protective package containing the option until you are instr ucted to do so. When you handle options and other computer components, take these precautions to avoid static electricity damage: v Limit your movement. Movement can cause static electricity to build up around you. v Always handle components [...]

Locating the connectors on the front of your computer The following illustration shows the locations of the connectors on the front of the computer . 1 Headphone connector 3 USB connector 2 Microphone connector 4 USB connector Chapter 3. Installing options 17[...]

Locating the connectors on the rear of your computer The following illustration shows the locations of the connectors on the rear of the computer . 1 Power connector 9 Ethernet connector 2 V oltage-selection switch (some models) 10 USB connectors 3 Mouse connector 11 Microphone connector 4 Keyboard connecto[...]

Connector Description Mouse connector Used to attach a mouse, trackball, or other pointing device that uses a standard mouse connector . Keyboard connector Used to attach a keyboar d that uses a standard keyboar d connector . Serial connector Used to attach an external modem, serial printer , or other devices that use a 9-pin serial connector . Par[...]

Obtaining device drivers Yo u can obtain device drivers for operating systems that are not preinstalled at http://www .lenovo.com/support/ on the W orld W ide W eb. Installation instructions ar e provided in README files with the device-driver files. Removing the cover Important Read “Important safety information” on page v and “Handling stat[...]

Locating components The following illustration will help you locate the various components in your computer . 1 Micropr ocessor and heat sink 5 PCI adapter connectors 2 Memory modules 6 PCI adapter 3 PCI Express x1 adapter connector (some models) 7 Power supply assembly 4 PCI Express x16 graphics adapter co[...]

The following illustration shows the locations of parts on the system board (some models). 1 Micropr ocessor and heat sink 11 Front USB connectors (2) 2 Micropr ocessor fan connector 12 Serial (COM2) connector 3 Memory connector 1 13 Front audio connector 4 Memory connector 2 14 PCI adapter connectors[...]

The following illustration shows the locations of parts on the system board (some models). 1 Micropr ocessor fan connector 11 Front panel connector 2 Micropr ocessor and heat sink 12 S ATA IDE connectors (2) 3 Memory connector 1 13 Front USB connectors (2) 4 Memory connector 2 14 Serial (COM2) connect[...]

Installing memory Y our computer has two connectors for installing DIMMs that provides up to a maximum of 4.0 GB of system memory . When installing memory modules, the following rules apply: v Use 1.8 V, 240-pin DDR2 SDRAM. v Use 256 MB, 512 MB, 1.0 GB or 2.0 GB memory modules in any combinatio up to 4.0. To install a memory module: 1. Removing the[...]

Installing adapters This section provides information and instr uctions for installing and removing adapters. Y our computer has four expansion connectors. There ar e two connectors for PCI adapters, one connector for a PCI Express x1 adapter , and one connector for a PCI Express x16 graphics adapter connector (some models). To install an adapter: [...]

5. Secure the adapter with the scr ew as shown. What to do next: v To work with another option, go to the appropriate section. v To complete the installation, go to “Replacing the cover and connecting the cables” on page 37. 26 User Guide[...]

Installing internal drives This section provides information and instr uctions for removing and replacing internal drives. Internal drives are devices that your computer uses to r ead and store data. Yo u can add drives to your computer to increase storage capacity and to enable your computer to read other types of media. Some of the dif ferent dri[...]

The following illustration shows the locations of the drive bays. The following table describes some of the drives you can install in each bay and their height requir ements. 1 Bay 1 - Maximum height: 43.0 mm (1.7 in.) CD drive or DVD drive (preinstalled in some models) 2 Bay 2 - Maximum height: 43.0 mm (1.7 in.) 3.5-inch hard disk driv[...]

Installing a drive To install an internal drive, follow these steps: 1. Remove the cover . See “Removing the cover” on page 20. 2. Remove the two screws at the r ear of the right side cover and slide the cover to the rear to r emove. 3. If your computer has a CD drive or DVD drive, you might need to remove the signal and power cables from the d[...]

5. Remove the front bezel by r emoving the two screws and r eleasing the six plastic tabs inside the chassis and then completely remove the bezel. Feed the power LED cable through the fr ont chassis opening as the bezel is removed. Note: Be careful so that you do not break the power LED cable, because the cable is attached to the bezel assembly . 3[...]

6. Remove the metal shield from the drive bay by inserting a flat-blade screwdriver into one of the slots and gently prying it loose. 7. Remove the plastic panel in the bezel for bay 2 by squeezing the plastic tabs that secure the panel on the inside of the bezel. 8. Make sure the drive that you ar e installing is set correctly as either a master o[...]

9. Install the drive into the bay . Align the screw holes and install four screws to secure the drive. 10. A hard disk drive r equires two cables; a power cable that connects to the power supply and a signal cable that connects to the system board. The steps to connect a drive are dif ferent depending on the type of drive you ar e connecting. Use o[...]

2. Connect the extra connector on the signal cable to the new drive. 3. Y our computer has extra power connectors for additional drives. Connect a power connector to the drive. What to do next v To work with another option, go to the appropriate section. v To complete the installation, go to “Replacing the cover and connecting the cables” on pa[...]

Padlock loop Y our computer is equipped with a padlock loop that locks the cover to your computer when a padlock is installed. Using a padlock at least or at 5 mm or 3/16-inch can secure your computer cover to help pr event unauthorized people from gaining access to the inside of your computer . Password protection To deter unauthorized use of your[...]

Refer to “Lithium battery notice” on page xii for information about replacing and disposing of the battery . To change the battery: 1. T urn off the computer and all attached devices. 2. Unplug the power cord and r emove the cover . See “Identifying parts on the system board” on page 21. 3. Locate the battery . See “Identifying parts on t[...]

9. T urn on the computer and all attached devices. 10. Use the Setup Utility program to set the date and time and any passwor ds. See Chapter 5, “Using the Setup Utility,” on page 47. Erasing a lost or forgotten password (clearing CMOS) This section applies to lost or forgotten passwor ds. For more information about lost or forgotten passwor ds[...]

Replacing the cover and connecting the cables After working with options, you need to install any removed parts, r eplace the cover , and reconnect any cables, including telephone lines and power cords. Also, depending on the option that is installed, you might need to confirm the updated information in the Setup Utility program. To replace the cov[...]

38 User Guide[...]

Chapter 4. Recovering software There ar e a variety of methods to choose from when considering how to r ecover software in the event of a softwar e or hardwar e-related pr oblem. Some methods vary depending on the type of operating system you have. This chapter will help you become familiar with recovery solutions pr ovided by Lenovo. This chapter [...]

v W indows V ista: Use Product Recovery discs to r estore your computer to the original factory contents only . When using Product Recovery discs on W indows XP , you are given the option to enter the Rescue and Recovery workspace and choose from a variety of r ecovery operations. When using Product Recovery discs on W indows V ista, you are prompt[...]

v On a protected ar ea of your hard disk v On a second hard disk installed in your computer v On an externally attached USB hard disk v On a network drive v On recor dable CDs or DVDs (a recor dable CD or DVD drive is requir ed for this option) After you have backed up your hard disk, you can r estore the complete contents of the hard disk, r estor[...]

multiple partitions on your hard disk, you have the option to r estore the factory contents to the C: partition and leave the other partitions intact. Because the Rescue and Recovery workspace operates independently from the W indows operating system, you can restor e the factory contents even if you cannot start the W indows operating system. Atte[...]

To create rescue media, do the following: 1. Open the Start menu from the W indows desktop, select All Programs , click Lenovo Care , then click Create Recovery Media . 2. In the Rescue Media area, select the type of r escue media you want to create. Yo u can create rescue media using a CD, USB har d drive, or a second internal hard disk drive. 3. [...]

2. Insert the Recovery Repair diskette into diskette drive A. 3. T urn on the computer and follow the instructions on the screen. Note: If the repair operation finishes without error , you will be able to access the Rescue and Recovery workspace by repeatedly pr essing the F1 1 key while you restart your computer . When you hear beeps or see a logo[...]

Setting a rescue device in the startup sequence Before you start the Rescue and Recovery pr ogram from a CD, DVD, USB har d disk drive, or any external device, you must first change the startup sequence in the Setup Utility . To view or change the startup sequence, do the following: 1. W ith the computer off, repeatedly pr ess and release the F1 ke[...]

46 User Guide[...]

Chapter 5. Using the Setup Utility The Setup Utility program is stor ed in the electrically erasable programmable read-only memory (EEPROM) of your computer . The Setup Utility program is used to view and change the configuration settings of your computer , regardless of which operating system you are using. However , the operating-system settings [...]

Password considerations A password can be any combination of up to twelve characters (a-z and 0-9) and symbols. For security reasons, it is a good idea to use a str ong password that cannot be easily compromised. Str ong passwords typically adher e to the following rules: v Have at least eight characters in length v Contain at least one alphabetic [...]

Using Security Profile by Device Security Profile by Device is used to enable or disable user access to the following devices: IDE controller When this feature is set to Disable , all devices connected to the IDE controller (such as har d disk drives or the CD-ROM drive) are disabled and will not be displayed in the system configuration. Diskette D[...]

Changing the startup device sequence To view or permanently change the configured startup device sequence, do the following: 1. Start the Setup Utility program (see “Starting the Setup Utility pr ogram” on page 47). 2. Select Startup . 3. Select Startup Sequence . See the information displayed on the right side of the screen. 4. Select the devi[...]

Chapter 6. Updating system programs This chapter contains information about updating POST/BIOS and how to recover from a POST/BIOS update failur e. Using system programs System programs ar e the basic layer of software that is built into your computer . They include the power-on self-test (POST), the basic input/output system (BIOS) code, and the S[...]

52 User Guide[...]

Chapter 7. T roubleshooting and diagnostics This chapter describes some basic troubleshooting and diagnostic pr ograms. If your computer problem is not described her e, see Chapter 8, “Getting information, help, and service,” on page 61 for additional troubleshooting r esources. Basic troubleshooting The following table provides information to [...]

Symptom Action The keyboard does not work. The computer does not respond to the keyboard. V erify that: v The computer is turned on. v The monitor is turned on and the brightness and contrast controls ar e set correctly . v The keyboard is secur ely connected to the keyboard connector on the front or rear of the computer . v No keys are stuck. If y[...]

v PC-Doctor for DOS or PC-Doctor for W indows PE, depending upon your machine type and model (used when your W indows operating system will not start) Notes: 1. Yo u can download the latest version of the PC-Doctor for W indows or PC-Doctor for DOS diagnostic programs fr om http://www .lenovo.com/ support/. T ype your machine type into the Use Quic[...]

Creating diagnostic diskettes To create diagnostic diskettes, download the PC-Doctor for DOS diagnostic program fr om http://www .lenovo.com/support/ onto two blank, formatted diskettes. If you do not have Internet access, create the diagnostic diskettes using the following procedur e: Note: Yo u will need a diskette drive on your computer or a USB[...]

1. Shut down the operating system and turn off the computer . 2. Repeatedly press and r elease the F1 1 key as you turn on the computer . 3. When you hear beeps or see a logo screen, stop pr essing the F1 1 key . The Rescue and Recovery workspace opens. Note: For some models, press the Esc key to enter Rescue and Recovery . 4. From the Rescue and R[...]

b. If there is some debris in the lens, gently blow the debris away fr om the area. 4. Check the surface on which you are using the mouse. If you have a very intricate picture or pattern beneath the mouse it may be dif ficult for the digital signal processor (DSP) to determine changes in the mouse position. 5. Reconnect the mouse cable to the compu[...]

7. Look for a build up of dirt on the plastic rollers 3 inside the ball cage. This build up usually appears as a stripe running acr oss the middle of the rollers. 8. If the rollers ar e dirty , clean them by using a cotton swab soaked in isopropyl (rubbing) alcohol. T urn the rollers with your finger and continue swabbing them until all the d[...]

60 User Guide[...]

Chapter 8. Getting information, help, and service If you need help, service, or technical assistance or just want more information about products manufactur ed by Lenovo, you will find a wide variety of sources available from Lenovo to assist you. Information resources This section provides information on how to access useful r esources r elating t[...]

– V iewing critical system information v Resource Center with support in one convenient place for tasks, such as: – One-button system recovery – Automatic updates – Performance restoration – Easy network connectivity and management v Message Center with information about system and support features including: – Notification of new versi[...]

Help and service If you need help and service for your computer , you will find a wide variety of sources available to help you. Using the documentation and diagnostic programs Many computer problems can be solved without outside assistance. If you experience a problem with your computer , see Chapter 7, “T roubleshooting and diagnostics,” on p[...]

For a list of service and support phone numbers for your country or region, go to http://www .lenovo.com/support/ and click Support phone list or refer to the warranty and safety information provided with your computer . Note: Phone numbers are subject to change without notice. If the number for your country or region is not pr ovided, contact your[...]

Appendix A. Manual modem commands This appendix provides commands for manually pr ogramming your modem. Commands are accepted by the modem while it is in Command Mode. Y our modem is automatically in Command Mode until you dial a number and establish a connection. Commands can be sent to your modem from a PC running communication software or any ot[...]

Command Function H1 Force modem of f-hook (make busy) Note: H1 command is not supported for Italy I_ I0 Display product-identification code I1 Factory ROM checksum test I2 Internal memory test I3 Firmware ID I4 Reserved ID L_ L0 Low speaker volume L1 Low speaker volume L2 Medium speaker volume L3 High speaker volume M_ M0 Internal speaker off M1 In[...]

Extended AT commands Command Function &C_ &C0 Force Carrier Detect Signal High (ON) &C1 T urn on CD when remote carrier is present &D_ &D0 Modem ignores the DTR signal &D1 Modem returns to Command Mode after DTR toggle &D2 Modem hangs up, returns to the Command Mode after DTR toggle &D3 Resets modem after DTR toggle [...]

Command Function &V1 Display Last Connection Statistics &W_ &W0 Stores the active pr ofile as Profile 0 &W1 Stores the active pr ofile as Profile 1 %E_ %E0 Disable auto-retrain %E1 Enable auto-retrain +MS? Displays the current Select Modulation settings +MS=? Displays a list of supported Select Modulation options +MS=a,b,c,e,f Selec[...]

Fax Class 1 commands +F AE=n Data/Fax Auto Answer +FCLASS=n Service Class +FRH=n Receive data with HDLC framing +FRM=n Receive data +FRS=n Receive silence +FTH=n T ransmit data with HDLC framing +FTM=n T ransmit data +FTS=n Stop transmission and wait Fax Class 2 commands +FCLASS=n Services class. +F AA=n Adaptive answer . +F AXERR Fax error value. [...]

+FPHCTO Phase C time out. +FPOLL Indicates polling request. +FPTS: Page transfer status. +FPTS= Page transfer status. +FREV? Identify revision. +FSPT Enable polling. +FTSI: Report the transmit station ID. V oice commands #BDR Select Baud Rate #CID Enable Caller ID detection and reporting format #CLS Select Data, Fax or V oice/Audio #MDL? Identify M[...]

Attention Switzerland User: If your Swisscom phone line does not have T axsignal switched OFF , modem function may be impaired. The impairment may be r esolved by a filter with the following specifications: T elekom PTT SCR-BE T aximpulssperrfilter-12kHz PTT Art. 444.1 12.7 Bakom 93.0291.Z.N Appendix A. Manual modem commands 71[...]

72 User Guide[...]

Appendix B. Notices Lenovo may not offer the pr oducts, services, or features discussed in this document in all countries. Consult your local Lenovo repr esentative for information on the products and services curr ently available in your area. Any refer ence to a Lenovo product, pr ogram, or service is not intended to state or imply that only that[...]

vary significantly . Some measurements may have been made on development-level systems and there is no guarantee that these measur ements will be the same on generally available systems. Furthermore, some measur ements may have been estimated through extrapolation. Actual r esults may vary . Users of this document should verify the applicable data [...]

Index A Access Help 62 adapter connectors 25 adapters installing 25 peripheral component interconnect (PCI) 14 slots 25 AGP connector 18 antivirus software, updating 10 arranging your workspace 1 audio line in connector 18, 19 audio line out connector 18, 19 audio, subsystem 12 B battery location 21 BIOS, updating (flashing) 51 C cables, connecting[...]

mouse, cleaning non-optical 58 optical mouse 57 N non-optical mouse 58 notices 73 O Online Books folder 61 operating system installing 10 updating 10 optical mouse 57 options available 14 external 14 internal 14 P parallel connector 18, 19 password administrator 48 erasing 36 lost or forgotten 36 setting, changing, deleting 48 user 48 passwords con[...]

[...]

Part Number: 41X8069 Printed in USA (1P) P/N: 41X8069[...]