-
Page 1
www .lg.com O WNER’S MANU AL L CD MONIT OR L CD MONIT OR MODEL E 2211PU E 2 4 11PU P l ea s e re a d th i s ma n u a l ca r e fu l l y b e for e op e r a t i n g yo u r se t a n d re tain it f or futur e ref erenc e. ENGLISH[...]
-
Page 2
1 This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the powe[...]
-
Page 3
2 Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Displays are provided with ventila[...]
-
Page 4
Important Precautions 3 On Cleaning Unplug the display before cleaning the face of the display screen. Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display screen because over-spraying may cause electrical shock. When cleaning the product, unplug the power cord and scrub gently with a soft cloth to prevent scratching. [...]
-
Page 5
4 Accessories !!! Thank for selecting LGE products !!! Please make sure the following items are included with your monitor . If any items are missing, contact your dealer . User's Guide/Cards Power Cord 15-pin D-Sub Signal Cable (To set it up, this signal cable may be attached to this product before shipping out.) DVI-D Signal Cable (This feat[...]
-
Page 6
Connecting the Display E221 1PU 5 Before setting up the monitor , ensure that the power to the monitor , the computer system, and other attached devices are turned off. Connecting the stand base 1 . Place the monitor with its front facing downward on a cushion or soft cloth. 2 . Assemble the Stand Base into the Stand Body. Be sure don't pull o[...]
-
Page 7
6 Connecting the Display E221 1PU IMPORTANT This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture. Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot. 3. Use a coin on the back of the stand base and turn the screw[...]
-
Page 8
7 Connecting the Display E241 1PU Before setting up the monitor , ensure that the power to the monitor , the computer system, and other attached devices are turned off. Connecting the stand base 1 . Place the monitor with its front facing downward on a cushion or soft cloth. 2 . Assemble the Stand Base into the Stand Body. Be sure don't pull o[...]
-
Page 9
8 Connecting the Display E241 1PU IMPORTANT This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture. Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot. Removing the stand base 1 . Place the monitor with its front f[...]
-
Page 10
9 Connecting the Display Height Range : maximum 4.33 inches (110.0 mm) * Please be sure to remove the Locking pin to adjust the height. 110.0 mm Positioning your display After installation, adjust the angle as shown below . 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range Swivel Range : 356˚[...]
-
Page 11
10 Connecting the Display ERGONOMIC I t is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees. WARNING You do not need to replace the Locking pin after it is removed, to adjust its height. When adjusting the angle of the screen, do not put your finge[...]
-
Page 12
11 Connecting the Display -The pivot function allows you to rotate the screen 90 degrees clockwise. 1 . Lift the monitor to its highest height to utilize the Pivot function. 2 . Landscape & Portrait : You can rotate the panel 9 0 o clockwise. Please be cautious and avoid contact between the monitor head and the Stand Base when rotating the scre[...]
-
Page 13
12 Connecting the Display A B Connect DVI-D(Digital signal) Cable Connect D-sub(Analog signal) Cable 1. Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. 2. Connect signal input cable and power cord in order, then tighten the screw of the signal cable. Connecting with[...]
-
Page 14
13 Connecting the Display NOTE ‘ Self Image Setting Function’? This function provides the user with optimal display settings.When the user connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual input signals. ‘AUTO’ Function? When you encounter problems such as blurry scre[...]
-
Page 15
14 Connecting the Display Connecting the USB(Universal Serial Bus) Cable 1. You can use the USB port at the back of the monitor to connect peripherals (USB mouse, USB keyboard, etc.) to the monitor, not to the computer. 2. The monitor’s USB terminal supports USB 2.0 and High Speed cables. Two USB Downstream ports Connect these ports to a mouse, U[...]
-
Page 16
15 Control Panel Functions Front Panel Controls MENU Button OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that they cannot be inadvertently changed. Press and hold the MENU button for several seconds. The message "OSD LOCKED" should appear. You can unlock the OSD controls at any time by pushing the [...]
-
Page 17
16 Control Panel Functions INPUT Button When two input signals are connected, you can select the input signal (D-SUB/DVI) you want. When only one signal is connected, it is automatically detected. The default setting is D-Sub. (SOURCE Hot key) Exit the OSD(On Screen Display). EXIT Button AUTO Button AUTO IMAGE ADJUSTMENT When adjusting your display[...]
-
Page 18
17 On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjus[...]
-
Page 19
18 On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. : D-SUB(Analog signal) input : DVI-D(Digital signal) input DSUB DVI-D To adjust the volume To customize the screen status for a user's operating environment To adjust the contrast of the screen To c[...]
-
Page 20
19 On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Sub- menus NOTE OSD (On Screen Display) menu languages on the monitor may differ from the manual. Menu Name[...]
-
Page 21
20 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description To adjust the brightness of the screen. Change the input image signal ratio to original. WIDE ORIGINAL Switch to full screen mode according to input image signal. * This function works only if input resolution is lower than monitor ratio (16:9). Exit : Exit , , : Move[...]
-
Page 22
21 On Screen Display(OSD) Selection and Adjustment Main menu Description To choose the language in which the control names are displayed. Press the , buttons to reset immediately. Restore all factory default settings except "LANGUAGE." To adjust the contrast of the screen. Exit : Exit , , : Move : Select another sub-menu[...]
-
Page 23
22 On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Sub-menus NOTE OSD (On Screen Display) menu languages on the monitor may differ from the manual. Menu Name [...]
-
Page 24
23 On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description Exit : Exit , : Move : Select another sub-menu Turn on the SUPER ENERGY SAVING fuction. When current setting value is ON,the SUPER SAVING color is green. Turn off the SUPER ENERGY SAVING function.Now the monitor is LED SAVING function. When current setting value is OF[...]
-
Page 25
24 On Screen Display(OSD) Selection and Adjustment SUPER SAVING LED SAVING 4 15 5 17 22 inch 24 inch Saving Data depends on the Panel. So,those values should be different from each panel and panel vendor. LG accumulate those values using integrated function with 10 minutes broadcast video signal. LED Saving means that how much power can be saved us[...]
-
Page 26
25 T roubleshooting No image appears Check the following before calling for service. No image appears Do you see a "OSD LOCKED" message on the screen? ● Is the power cord of the display connected? ● Is the power indicator light on? ● Is the power indicator flickering? ● Do you see an "OUT OF RANGE" message on the screen?[...]
-
Page 27
26 T roubleshooting Display image is incorrect ● Display Position is incorrect. ● On the screen background, vertical bars or stripes are visible. ● Any horizontal noise appearing in any image or characters are not clearly portrayed. • Press the AUTO button to automatically adjust your display image to the ideal setting. If the results are u[...]
-
Page 28
27 Display image is incorrect T roubleshooting ● The screen color is mono or abnormal. ● The screen blinks. • Check if the signal cable is properly connected and use a screwdriver to fasten if necessary. • Make sure the video card is properly inserted in the slot. • Set the color setting higher than 24 bits (true color) at Control Panel -[...]
-
Page 29
28 Specifications E221 1PU 54.6 cm ( 21.5 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 54.6 c m 0.248 x 0 . 248 mm (Pixel pitch) Display Horizontal Freq. 30 kHz to 83 kHz (Automatic) Vertical Freq. 56 Hz to 75 Hz (Automatic) Input Form Separate Sync. Digital Sync Input Signal Input 15 pin D-Sub Connector DVI-D C[...]
-
Page 30
29 Specifications E241 1PU 60.9 cm ( 24 inch) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 60.9 c m 0.276 x 0 . 276 mm (Pixel pitch) Display Horizontal Freq. 30 kHz to 83 kHz (Automatic) Vertical Freq. 56 Hz to 75 Hz (Automatic) Input Form Separate Sync. Digital Sync Input Signal Input 15 pin D-Sub Connector DVI-D Con[...]
-
Page 31
30 Specifications Preset Modes (Resolution) Display Modes (Resolution) Horizontal Freq. (kHz) Vertical Freq. (Hz) *Recommend Mode 1 2 3 4 5 6 7 8 9 10 11 *12 720 x 400 640 x 480 640 x 480 800 x 600 800 x 600 1024 x 768 1024 x 768 1152 x 864 1280 x 1024 1280 x 1024 1680 x 1050 1920 x 1080 31.468 31.469 37.500 37.879 46.875 48.363 60.023 67.500 63.98[...]
-
Page 32
31 Installing the W all mount plate This monitor satisfies the specifications of the W all mount plate or the interchange device. 1 . After moving the product to face downward, make sure to place it on a soft cloth or a cushion to avoid surface damage. 2 . Separate the head and the stand with the use of a screwdriver.[...]
-
Page 33
32 Wall mount plate(Separate purchase) This is stand-type or wall mount type and is connectable with Wall mount plate. Please refer to the installation guide for more details, which is provided when Wall mount plate is purchased. Kensington Security Slot Connected to a locking cable that can be purchased separately at most computer stores. 3. Insta[...]
-
Page 34
M a k e s u r e to r e a d t h e Sa f et y P r e c a ut i on s befor e using the product . K e e p t h e O W N E R ’ S M A N U A L ( C D ) i n a n acces sible place f or furture ref erence. The m ode l and seri al n umbe r of th e SE T is located o n the bac k or one sid e of the SET . Rec ord it below should y ou ever need ser vice. MODEL SERIAL[...]