Life Fitness SM61 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23

Go to page of

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Life Fitness SM61, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Life Fitness SM61 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Life Fitness SM61. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Life Fitness SM61 should contain:
- informations concerning technical data of Life Fitness SM61
- name of the manufacturer and a year of construction of the Life Fitness SM61 item
- rules of operation, control and maintenance of the Life Fitness SM61 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Life Fitness SM61 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Life Fitness SM61, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Life Fitness service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Life Fitness SM61.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Life Fitness SM61 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    M051-K50-A137 1 6 STA CK MULTI-JUNGLE (SM61) WITH 2 A DJUSTA BLE PULLEYS UNPA CKING A ND A SSEMBLY INSTRUCTIONS[...]

  • Page 2

    SM61 U npacking & Assembly Instructions 2 The SM61 c om es partially assem bled. Follow the steps below to com plete the as sem bly. WA RNING: COMPONENTS O F THE SM61 ARE LARGE AND HEAVY. USE CAUTION WHEN ASSEMBLING T HIS MACHINE. MA TERIA LS A ND TOOLS REQUIRED FOR A SSEMBL Y 1/2”, 3/8”, 5/8” & 9/16” Sock et wrench with extension 1[...]

  • Page 3

    SM 61 Unpacking & Assembly Instr uctions 3 UNPA CKING Follow the steps below when unpacking the c om ponents of the SM61. 1. Cut off the shipping wrapper. 2. Remove th e parts boxes an d shippin g boards. 3. Remove the item s in the parts box es. Thes e item s are s hown in Figure 1. A. Remove the bolts bag. B. Remove the par ts shown below. Pa[...]

  • Page 4

    SM61 U npacking & Assembly Instructions 4 A SSEMBLY Figure 2 shows an ass em bled SM61. 1 1 2 2 4 4 3 5 5 6 7 Figure 2. SM61 main compone nts. 1. Cubes (2) 2. Lat bench ( 2) 3. Connecting beam (1) 4. Lat tops (2) 5. T ricep top (2) 6. 300 lb. W eight stack s (2) 7. 190 lb. W eight stack s (4) 1. Place the two weight “cubes” in their “fina[...]

  • Page 5

    SM 61 Unpacking & Assembly Instr uctions 5 Figure 3. Set t he w eight stack cu bes. 2. Bolt on the teardrop pulleys above the lat benches (see F igure 4) on both cubes using two 3/8” x 2-3/4” hex head bolts (used to bolt the cr oss beam to the cr oss m em bers and the adjustable pulley tops to the top beams ). Include the 3/8” f lat washe[...]

  • Page 6

    SM61 U npacking & Assembly Instructions 6 Figure 5. Configura tion for 2-3/4” and 3” bolts. 3. Using a 5/8” soc ket with extens ion and com bination wrench, bolt on the connec ting beam to the c ubes using two of the lar ge 7/16” x 6” bolts , 7/16” washers, and 7/16” nuts, end cap washers and end caps. Figur e 6 shows the connecte[...]

  • Page 7

    SM 61 Unpacking & Assembly Instr uctions 7 4. Using a 5/8” soc ket and c om bination wrench, m ount the 56” lat tops (par t T f rom HARDWARE sec tion) to the cells by inserting two of the large 7/16” by 6” bolts using the hardware configur ation shown in Figure 7. Mount the 29” tric ep top (part U in HARDWARE sec tion) to the f ram e [...]

  • Page 8

    SM61 U npacking & Assembly Instructions 8 150 lb. weight stack 300 l b. weight st ack 150 lb. weig ht stack Figure 8. Mount rubber bumpers and the w eight stacks. 5. Install the weight stack s. T o do this: A. Using a 9/16” soc ket and c om bination wrench, rem ove the tric ep back rest bolts (see Figure 9) . B. Using a 9/16” soc ket and c [...]

  • Page 9

    SM 61 Unpacking & Assembly Instr uctions 9 C. Prepare the w eight stack. Slide the guide rods ( 2) through the weight stack s (1) as shown below. Place rubber bum pers (3) on the bottom s of each guide rod. Make s ure the pull pin (4) is in the bottom weight plate. D. Flip ov er the w eight stacks. W hen shipped, the weight stac ks have the pul[...]

  • Page 10

    SM61 U npacking & Assembly Instructions 10 rest m ounted to the f ram e as shown in Figure 9) . You will need to remove the pulley from the housing to thr ead the plug into the weight stack bayonet. Make sure the 9/16” jam nut is thr eaded 1-5/8” away from the pulley as shown in Figure 11. Leave the pulley s out since you will need to have [...]

  • Page 11

    SM 61 Unpacking & Assembly Instr uctions 11 Use a pi nch bar to ali g n the seat frame h oles to the cube s Figure 13. Mount the benche s to the frame. Figure 14. Bolt t he benches to the frame.[...]

  • Page 12

    SM61 U npacking & Assembly Instructions 12 INSTA LLING THE CABLES The SM61 us es six c ables. T here are three dif ferent types of c able used on the SM61. They are: 1. Adjustable c ross over cables (ball end cables) (2). 2. Lat pulldown and tricep cables ( 4). The lat and tric ep cables c an be identified by their short length, the low row cab[...]

  • Page 13

    SM 61 Unpacking & Assembly Instr uctions 13 ADJUSTABLE CROSSOVER CABLE RO UTI NG Once you’ve removed the pulleys as desc ribed previously, route the three adjustable cross over cables as shown in Figure 16. Figure 16. Adjustable crossov er cable routin g.[...]

  • Page 14

    SM61 U npacking & Assembly Instructions 14 Figure 17. Adjustable crossover cab le end detail. Using a 7/8” wrench, tighten the j am nut onto the adjustable pulley threads as shown in Figure 17. Place a rubber c ap on the top of the cable as shown in Figure 17 (right) . Bolt the cable to the weight stack s as s hown in Figure 18. Thr ead the 7[...]

  • Page 15

    SM 61 Unpacking & Assembly Instr uctions 15 LAT PULLDOWN CABLE RO UTI NG Route the lat pulldown cable as shown in Figure 19. Scr ew the cable into the weight stack as shown previously in Figure 18. Figure 19. La t pulldow n cable routing. TRICEP PUSHDOW N CABLE RO UTI NG Route the tricep pushdown cable as shown in Figure 20. Screw the cable int[...]

  • Page 16

    SM61 U npacking & Assembly Instructions 16 Figure 20. Tricep pus hdow n cable routing.[...]

  • Page 17

    SM 61 Unpacking & Assembly Instr uctions 17 HA RDWARE 0123456 ½½½½½½ A B C D K H J E F G 6” Bolt Hardware 2-3/4” & 3” Bolt Ha rd wa re Hardware F igure 1. Assembly Parts.[...]

  • Page 18

    SM61 U npacking & Assembly Instructions 18 The parts shown in Hardware Figure 1 are us ed to assem ble the SM61. T hey are: A. 7/16” x 6” hex head bolt (used to bolt the tric ep top beam , adjustable c rossover top beam, lat top beam s , and connecting beam to the tops of the cubes ) B. 3/8” x 3” hex head bolt (used to bolt the cr oss b[...]

  • Page 19

    SM 61 Unpacking & Assembly Instr uctions 19 The part s hown in Hardware Figure 3 is the 9/16” c able jam nut that’s used to s ecure the cables to the weight stack s. Hardware Figure 3. Cable ja m nut. M. Cable jam nut Hardware Figure 4 shows the types of cables that ar e included with the SM61. N P Q Hardware Figure 4. Cables . N. Lat pulld[...]

  • Page 20

    SM61 U npacking & Assembly Instructions 20 S T U Hardware F igure 5. T op assemblies. S. Teardr op pulleys (bolt on above lat and seated row benches) (2 ) T. 56” Lat tops (bolt to top of cells with pulleys above lat benches) (2) U. 29” Tr icep top (bolt on to 56” lat top bar ) (2)[...]

  • Page 21

    SM 61 Unpacking & Assembly Instr uctions 21 Hardware Figure 6. Weight stack rubber bumpers. W . W eight s tack rubber bum pers (inserted under weight stac ks ) Hardware Figure 7. Floating pulle ys. X. Floating pulleys (bolt to 190 lb weight stack s other than tric ep pushdown stack )[...]

  • Page 22

    SM61 U npacking & Assembly Instructions 22 PA RTS LIST Part # ID Description Quantity Main components 1 2 3 4 5 6 7 Cubes Lat bench Connecting beam Lat tops Tr icep top 300 lb weight stack 190 lb weight stack 2 2 1 2 2 2 4 0017-00042-0936 0017-00103-0234 0017-00101-1408 0017-00101-1408 0017-00101-1561 Cables, caps & nuts L M N P Q Rubber ca[...]

  • Page 23

    SM 61 Unpacking & Assembly Instr uctions 23 0017-00101-1413 0017-00104-0368 0017-00103-0217 Pulley hardw are (installed) 1-3/4” Bolt Cap washer 3/8” Nyloc nut 0017-00101-1413 0017-00104-0313 0017-00103-0217 Floating pulley hardware (installed) 1-3/4” Bolt Flat washer 3/8” Nyloc nut[...]