Lowrance electronic GlobalMap 4800M manual

Pub. 988-0151-191 www.lowrance.com GlobalMap 4800M Mapping GPS Receiver Operation Instructions ®[...]

Copyright © 2003 Lowrance Electronics, Inc. All rights reserved. Lowrance ® is a registered trademark of Lowrance Electronics, Inc. Navionics  is a registered trademark of Navionics, Inc. Points of Interest Data in this unit are by infoUSA, copyright  2001-2003, All Rights Reserved. infoUSA is a trademark of infoUSA, Inc. eXitSource Databas[...]

i Table of Contents Section 1: Read Me First! ......................................................... 1 Capabilities and Specifications: GlobalMap ® 4800 ..................... 2 How Lowrance GPS Works .......................................................... 4 Introduction to GPS and WAAS ................................................... 6 Ho[...]

ii Navigate a Back Trail (backtrack, or reverse)....................... 49 Transfer Custom Maps and GPS Data Files ............................. 50 Cancel Navigation ....................................................................... 52 Section 4: Advanced GPS Operations ................................. 53 Find Distance From Current Position T[...]

iii Configure NMEA ........................................................................ 71 Coordinate System Selection ...................................................... 71 To setup Loran TD: ................................................................. 72 Map Fix .........................................................................[...]

iv Trail Update Rate (Time, Distance) ................................... 94 Delete Trail ............................................................................. 95 New Trail ................................................................................. 95 Trail Visible/Invisible and Other Trail Options .................... 95 Units of Mea[...]

1 Section 1: Read Me First! How this manual can get you out on the road, fast! Welcome to the exciting world of digital GPS! We know you're anxious to begin navigating, but we have a favor to ask. Before you grab the GlobalMap  4800 and begin installing it, please give us a moment or two to explain how our manual can help you get the best p[...]

2 Section 3 contains short, easy-to-scan GPS lessons that follow one an- other in chronological order. They're all you'll need to know to find your way on the water or in the wilderness quickly. After you've learned the basics (or if you already have some GPS expe- rience), you may want to try out some of the GlobalMap 4800's ma[...]

3 Input power: ................... 10 to 15 volts DC. Case size: ......................... 5.4" H x 6.9" W x 3.4" D (13.8 x 17.6 x 8.6 cm); sealed and waterproof; suitable for saltwater use. MMC slots: ...................... One with waterproof door (SD card compati- ble). Recording: ........................ MMC & S D mem ory c a[...]

4 Plot Trails: ...................... 10 savable; up to 9,999 points per trail. Zoom range: .................... 39 ranges; 0.02 to 4,000 miles. NOTE: The above memory capacities re fer only to the GlobalMap 4800's on- board memory. The amount of GPS data you can record and save for recall later is only limited by the number of MMC cards you h[...]

5 The background map is suitable for many navigation chores, but for maximum accuracy and much more detail, you need our optional map- making software, MapCreate  6. Some unit features — such as searching for businesses and addresses — won't work without a custom MapCreate map. There is so much detail in our background map (and even mor[...]

6 Introduction to GPS and WAAS Well, now you know the basics of how the unit does its work. You might be ready to jump ahead to Section 2, Installation & Accessories, on page 11, so you can mount your GlobalMap 4800 and plug in the power. Or you might want to see how our text formatting makes the manual tuto- rials easy to skim. If that's [...]

7 The system requires signal reception from three satellites in order to determine a position. This is called a 2D fix. It takes four satellites to determine both position and elevation (your height above sea level — also called altitude). This is called a 3D fix. Remember, the unit must have a clear view of the satellites in order to receive the[...]

8 receiver is only a tool. Always have another method of navigation avail- able, such as a map or chart and a compass. Also remember that this unit will always show navigation information in the shortest line from your present position to a waypoint, regardless of terrain! It only calculates position, it can’t know what’s between you and your d[...]

9 For example, instructions for navigating a trail would look like this: 1. From the Map Page, press MENU | MENU | ↓ to M Y T RAILS | ENT . 2. Press ↓ to Trail 1 | ENT | → | ↓ to N AVIGATE | ENT . 3. You are asked to wait while it converts the trail into a route. 4. The wait message disappears and the GlobalMap 4800 begins showing navigatio[...]

10 Notes[...]

11 Section 2: Installation & Accessories Preparations You can install the GPS system in some other order if you prefer, but we recommend this installation sequence: Caution: You should read over this entire installation section before drill- ing any holes in your vehicle or vessel! 1. Determine the approximate location for the GPS unit, so you [...]

12 You need to select an antenna installation location that has a clear, un- obstructed view of the sky. After the module is installed, connect it to the end of the Y-adapter extension cable as shown in the following dia- gram. To connect it to the unit, insert the cable's splitter plug into the Network socket on the back of the unit and your [...]

13 The Power/Data cable for this unit. Depending on your configuration, you may not use all of these wires. (For example, many units cannot operate an optional external speaker, so the white wire on the Power Supply cable isn't functional.) The fol- lowing segments include instructions for installing all the wires that you will use with this u[...]

14 CAUTION: When using the unit in a saltwater environment, we strongly rec- ommend that you shut off the power supply to the power cable when the unit is not in use. When the unit is turned off but still connected to a power supply, electrolysis can occur in the power cable plug. This may result in corrosion of the plug body along with the electri[...]

15 NOTE: If you're powering a NMEA-2000 buss, you will attach both the NMEA-2000 Power cable and the unit's Power Supply cable to the boat's battery. To attach the NMEA-2000 Power cable, connect the red wire to battery's + and black and shield wires to battery's –. WARNING: This product must be independently fused with th[...]

16 See the following diagram for general wiring connections. Read your other product’s owner’s manual for more wiring information. NMEA/DGPS Wiring (Data cable) To exchange NMEA 0183 or DGPS data, the GlobalMap 4800M has one NMEA 0183 version 2.0 communication port. Com port one (Com-1) can be used to receive NMEA format GPS data or DGPS data. [...]

17 If you use the supplied bracket, you may be interested in the optional R-A-M  bracket mounting system. This converts the unit's gimbal bracket to a swivel mount, which can be used on the dash or overhead mounting positions. Optional R-A-M mounting system. Bracket Installation Mount the GlobalMap 4800 in any convenient location, provided [...]

18 Drill a 1-inch (25.4 mm) hole in the dash for the power and antenna cables. The best location for this hole is immediately under the gimbal bracket location. This way, the bracket can be installed so that it covers the hole, holds the cables in position and results in a neat installation. Some customers, however, prefer to mount the bracket to t[...]

19 In-Dash Installation You can mount the GlobalMap 4800 in the dash with an optional FM-5 In-Dash Adapter Kit. The kit includes mounting hardware, a template for cutting the hole and an instruction sheet, part 988-0147-43. In-dash mounting template for the GlobalMap 4800, showing dimensions. NOTE: The figure above is not printed to scale. A scaled[...]

20 Install batteries in power pack battery adapter. MMC or SD Card Memory Card Installation Your GlobalMap 4800 uses a MultiMedia Card to store information, such as custom maps, waypoints, trails and other GPS data. The unit can also use Secure Digital Cards (SD card) to store data. NOTE: Throughout this manual, we will use the term MMC, but just r[...]

21 Memory card compartment with a 16 MB MMC card installed. To remove an MMC 1. Open the card compartment door by unscrewing the thumb screw. The screw should only be finger tight. If it was over-tightened, use a thumbnail, a coin or a screwdriver to open the door. 2. Just press a finger against the label of the MMC and drag it from the slot. 3. Cl[...]

22 MapCreate™ 6 CD-ROM, left; MMC card reader for USB ports, right. Now that you have your GlobalMap 4800 installed, move on to Section 3, Basic GPS Operations . There, we'll present a series of step-by-step tutorials to teach you the basics of GPS navigation. Face Cover Your unit comes with a white protective cover that snaps on and off the[...]

23 Section 3: Basic GPS Operations This section addresses the unit's most basic GPS operations. The tuto- rials presented in Sec. 3 follow a chronological order. Sec. 4, Advanced GPS Operations , will discuss other more advanced functions and utili- ties. Material in Sec. 4 is arranged in alphabetical order. Before you turn on the unit and fin[...]

24 3. MENU – Press this key to show the menus and submenus, which allow you to select a command or adjust a feature. This also accesses search functions for streets, intersections, addresses and highway exits. 4. ARROW KEYS – These keys are used to navigate through the menus, make menu selections, move the map cursor and enter data. 5. ENT/ICON[...]

25 Main Menu. The Main Menu commands and their functions are: Screen command: changes the contrast or brightness of the display screen. Sounds command: enables or disables the sounds for key strokes and alarms and sets the alarm style. Alarms command: turns GPS alarms on or off and changes alarm thresholds. Route Planning command: used to plan, vie[...]

26 Page. They are accessed by pressing the PAGES key, then using → or ← to select a Page. (Clear the Pages Menu by pressing EXIT .) Pages Menu, showing some Map display options. Satellite Status Page The Satellite Status Page, shown, provides detailed information on the status of the unit's satellite lock-on and position acquisition. To ge[...]

27 This screen shows a graphical view of the satellites that are in view. Each satellite is shown on the circular chart relative to your position. The point in the center of the chart is directly overhead. The small inner ring represents 45° above the horizon and the large ring represents the horizon. North is at the top of the screen. You can use[...]

28 Navigation Page, recording a trail, traveling southwest. Page looks like this when the unit is not navigating to a waypoint, following a route, or backtracking a trail. When navigating to a waypoint, the Navigation screen looks like the following figure. Your ground speed, track, distance and bearing to waypoint, and course are all shown digital[...]

29 The Off Course window shows the current cross track error. This shows the distance you are off-course to the side of the desired course line. The course line is an imaginary line drawn from your position when you started navigating to the destination waypoint. The course line is shown on the Navigation Page screen (and the Map Page screen) as a [...]

30 In the preceding example figure, the driver is headed west (a 265º track) toward a waypoint 265º (bearing) away. The cross track error range (white corridor) is 0.20 miles either side of the course. The driver is headed toward trail waypoint 4, which is 0.3 miles away. The vehicle is right on course. Traveling at a speed of 8 mph, the driver w[...]

31 Far left, Map Page opening screen. Center, zoomed to 100 miles and right, zoomed to 10 miles. Over Zoomed means you have reached the detail limits in an area covered only by the basic background map. Zooming in any closer will reveal no more map details because a high- detail custom map has not been loaded on the MMC for this area. If you'r[...]

32 national forests and parks); some major city streets; Interstate, U.S. and state highways; Interstate highway exits and exit services informa- tion; large- and medium-sized lakes and streams; and more than 60,000 navigation aids and 10,000 wrecks and obstructions in U.S. coastal and Great Lakes waters MapCreate custom maps include massive amount[...]

33 Tip: In some urban areas, businesses are so close to one another that their POI icons crowd each other on the screen. You can reduce screen clutter and make streets and other map features easier to see by simply turning off the display of POIs you're not watching for. (To see how, check the text on Map Detail Category Selection, page 80. It[...]

34 Pages Menu with Two Map option selected, left. Map Page with two map windows, at right. The left map is active. Resize Window is another extremely handy feature for pages that have two major windows. You can change the horizontal size of the windows to suit your viewing preference. Here's how: 1. From any two-window display, press MENU | ?[...]

35 Basic GPS Quick Reference Start outdoors, with a clear view of the open sky. As you practice, try navigating to a location at least a few blocks away. While you're learning, navigation in too small an area will constantly trigger arrival alarms. 1. Connect the unit to electric power and the antenna module. Make sure the MMC is in. (See comp[...]

36 Find Your Current Position Finding your current position is as simple as turning the unit on. Un- der clear sky conditions, the unit automatically searches for satellites and calculates its position in approximately one minute or less. NOTE: "Clear sky" means open sky, unobstructed by terrain, dense foliage or structures. Clouds do not[...]

37 The selected airport to the northwest is 4.2 miles away. Selecting Any Map Item With the Cursor 1. Use the zoom keys and the arrow keys to move around the map and find the item you wish to select. 2. Use the arrow keys and center the cursor cross-hair on the desired ob- ject. On most items, a pop-up box will give the name of the selected item. T[...]

38 2. You could search the entire restaurant category, but in this example we will narrow our search. Press → to S UBCATEGORY column| ↓ to F AST F OOD C HAINS | ENT | ↓ to N EAREST | ENT . 3. The unit says it is calculating, then a list of restaurants appears, with the closest at the top of the list, and the farthest at the bottom of the list[...]

39 6. The unit's map appears, with the cross-hair cursor highlighting the restaurant' s POI symbol. A pop-up data box shows the POI's name, distance and bearing. A data box at the bottom of the screen continues to display the location's latitude and longitude. Map screen showing Finding Waypoint, the result of a restaurant searc[...]

40 Create Waypoint at Current Position While you are traveling, press WPT | WPT . The waypoint is saved and automatically given a name with a sequential number, such as "way- point 003." The waypoint symbol and number appear on the map. Sequence for setting a waypoint. Step 1: while traveling, quickly press WPT twice to call up Find Waypo[...]

41 Create Waypoint on Map 1. Use the arrow keys to move the cursor to the place where you want to make a waypoint. 2. Press WPT | WPT . The waypoint is saved and automatically given a name with a sequential number, such as "waypoint 001." The waypoint symbol and number appear on the map. Create Waypoint by Entering a Position 1. Press WPT[...]

42 Navigation Page, navigating toward waypoint 004 and leaving a trail. Set Man Overboard (MOB) Waypoint One of boating's most terrifying events is having a friend or family member fall overboard. This situation can be deadly on any body of wa- ter — fresh or salt. It's particularly dangerous at night or if you're out of sight of l[...]

43 Navigating to Man Overboard: Man Overboard Activated message, left, Navigation Page, center, Map Page, right. The victim is to the starboard of the vessel; the GPS shows which direction to steer to for the rescue. The man overboard position is also stored in the waypoint list for future reference. It can be edited the same as any other waypoint.[...]

44 3. Press MENU | ENT and the unit will begin navigating to the cursor lo- cation. The Map Page will display a dotted line from your current position to the cursor position. The Navigation Page displays a compass rose showing navigation information to your destination. See the following examples. The 15-mile zoom figure at left clearly shows the d[...]

45 particularly handy when you are trying to retrace your trip and go back the way you came. On the screen, trails are represented by a solid line extending from the back of the current position arrow. The unit is set at the factory to automatically create and record a trail while the unit is turned on. The unit will continue recording the trail un[...]

46 New trail, named "Trail 15," is created when Trail 14 is made inactive. Any new travel will be recorded in this trail, which is active and visi- ble. Trails do not need to be visible in order to be active. You can save and recall up to 10 different plot trails, which can also be copied to your MMC for archiving or for transfer to your [...]

47 To turn on trail display: 1. Press MENU | MENU | ↓ to M Y T RAILS | ENT . 2. Press ↓ | ↓ to enter the Saved Trail list, then use ↑ or ↓ to select the desired Trail Name | ENT . 3. Press ↓ to A CTIVE | → to V ISIBLE | ENT . To return to the previous page, press EXIT | EXIT | EXIT | EXIT . Navigating Trails There are three methods fo[...]

48 3. Press → to D ELETE T RAIL | ↓ to N AVIGATE | ENT . 4. Press ↓ to N AVIGATE | ENT . The unit begins showing navigation infor- mation along the trail. NOTE: If you are already located at or near the beginning of your trail, the arrival alarm will go off as soon as you hit Enter. Just press EXIT to clear the alarm and proceed. 5. Now, begi[...]

49 Navigate trail, map views: at left driver is northbound heading straight toward trail point 6. At right, northbound driver has reached point 6 and has turned west to follow trail. Navigate trail, navigation page (compass rose) views: at left, driver is northbound heading straight toward trail point 6; bearing arrow shows the trail point is due n[...]

50 NOTE: If you are already located at or near the end of your trail, the arri- val alarm will go off as soon as you hit Enter. Just press EXIT to clear the alarm and proceed. 5. Now, begin moving and follow your unit. 6. When you reach your destination, be sure to cancel your navigation: press MENU | MENU | ↓ to C ANCEL N AVIGATION | ENT . The u[...]

51 The Transfer My Data submenu asks if you want to save data to the MMC or load data from the MMC into the unit's memory. 2. The Transfer My Data menu includes a message which tells you if an MMC is present or not. If no MMC is present, you must first insert a card into the unit in order to activate the Load or Save commands. To transfer data[...]

52 4. Loading to unit memory : There may be more than one GPS Data File (*.USR) on the card. To select a file, press ENT to activate the selec- tion box, use ↓ or ↑ to highlight the file, then press ENT to accept the selection. Next, press ↓ to L OAD D ATA | ENT . The unit will display a com- pletion message when the data transfer is finished[...]

53 Section 4: Advanced GPS Operations Find Distance From Current Position To Another Location 1. While on the Map Page press: MENU | ↓ to F IND D ISTANCE | ENT . 2. Center your cursor over the position you want to find the distance to. A rubber band line appears, connecting your current position to the cursor's location. The distance along t[...]

54 Icons Icons are graphic symbols used to mark some location, personal point of interest or event. They can be placed on the map screen, saved and re- called later for navigation purposes. These are sometimes referred to as event marker icons. This unit has 42 different symbols you can pick from when creating an icon. Icons are similar to waypoint[...]

55 1. Press MENU | ↓ to D ELETE M Y I CONS | ENT . 2. Press ↓ to D ELETE A LL I CONS , D ELETE B Y S YMBOL , or D ELETE F ROM M AP and press ENT . Delete icons menu. The Delete All Icons command will ask if you are sure. Press ← to Y ES | ENT . All icons will be deleted from the map. The Delete by Symbol command will launch the Select Symbol [...]

56 A route provides the automatic capability to navigate through several waypoints without having to reprogram the unit after arriving at each waypoint. Once programmed into the GPS unit, a route provides the option of navigating forward through the route waypoints or in reverse order (you can even begin navigating in the middle of a route!) Create[...]

57 2. Press ↓ to (E ND OF R OUTE ) | ENT | ↓ to A DD F ROM M AP | ENT . The Map Page appears with the cursor showing. Edit Route menu, left. Edit Route Waypoints menu, right, with Add From Map command selected. 3. Use the Zoom keys and arrow keys to move the map and cursor until the cursor is centered on the spot where you want your route to be[...]

58 Route creation sequence, continued: Fig. 4. Point (3) set at on-ramp turn. Fig. 5. Waypoint (4) set at highway exit to frontage road leading to river. Waypoint (5) ends the route at a tree stand in the hunting area. Fig. 6. Press EXIT to save the route and you return to this screen. 5. Move the cursor to the next point in the route, a spot where[...]

59 Edit a Route Name You can edit the route name if you wish. 1. From the N AVIGATION P AGE , press MENU | ENT or from the M AP P AGE press MENU | MENU | ↓ to R OUTE P LANNING | ENT . 2. Press ↓ to route name | ENT | ENT . 3. Press ↑ or ↓ to change the first character, then press → to move the cursor to the next character and repeat until[...]

60 NOTE: When adding waypoints to a route, the inserted waypoints will ap- pear in the route in front of the waypoint you have selected. To in- sert waypoints at the end of the route, make sure to select "(End of route)" before adding them. Navigate a Route 1. From the N AVIGATION P AGE , press MENU | ENT or from the M AP P AGE , press ME[...]

61 Navigating along a route: Fig. 1 shows the Navigation Page at the start of a route, heading straight for the first waypoint (Wpt 1). In Fig. 2, the traveler has arrived at Wpt 1; the arrival alarm has been triggered and the bearing arrow on the compass rose has turned to point toward Wpt 2, off to the east. In Fig. 3 the traveler has turned east[...]

62 Edit a Trail Name To edit a trail name: press MENU | MENU | ↓ to M Y T RAILS | ENT | ↓ to trail name | ENT | ENT . Press ↑ or ↓ to change the first character, then press → to the next character and repeat until the name is correct. Press ENT then EXIT | EXIT | EXIT | EXIT to return to the previous page display. Tip: You can quickly cal[...]

63 At left, Edit Trail Menu with Pattern option selected. At right, edited trail with dotted line pattern. Utilities Utilities are useful tools for traveling or for outdoor activities. Alarm Clock To get to the alarm clock menu: press MENU | MENU | ↓ to T IMERS | ENT | ↓ to A LARM C LOCK | ENT . Sun/Moon Rise & Set Calculator To get to the [...]

64 To delete a waypoint from the map: 1. Use the arrow keys to select the waypoint with the cursor. 2. Press WPT | → to D ELETE W AYPOINT | ENT | ← to Y ES | ENT . To return to the previous page and clear the cursor, press EXIT . To delete all waypoints at one time: press MENU | MENU | ↓ to S YSTEM S ETUP | ENT | ↓ to D ELETE A LL M Y W AYP[...]

65 Set a Waypoint by Average Position This feature sets a waypoint at the current position after taking several position readings and averaging them. This boosts waypoint position accuracy by helping to eliminate errors caused by atmospheric condi- tions and other factors. 1. Press WPT | → to S UBCATEGORY column| ↓ to N EW | ENT . 2. Press ↓ [...]

66 Notes[...]

67 Section 5: System & GPS Setup Options Alarms This unit has several GPS alarms. The factory default setting has all of these but the anchor alarm turned on. You can turn the alarms off and on and change their distance settings. You can set an arrival alarm to flash a warning message and sound a tone when you cross a preset distance from a way[...]

68 3. To change distance settings, scroll ↓ or ↑ to select the desired cate- gory, then press → | ENT to activate the distance dialog box. Press ↑ or ↓ to change the first character, then press → to the next character and repeat until the name is correct. 4. When your adjustments are finished, return to the last page dis- played by repe[...]

69 GPS Auto Search on the Satellite Status Menu. You can force the unit to immediately kick into auto search mode. Here's how: From the Satellite Status page, MENU | ↓ to GPS A UTO S EARCH | ENT | ← to Y ES | ENT . Check MMC Files and Storage Space To check MMC Files: Press MENU | MENU | ↓ to B ROWSE MMC F ILES | ENT. Main Menu, left, MM[...]

70 Menus for changing Com Port settings. For connectors and wiring information for another device, see page 16. For assistance in configuring the unit to communicate with another device, consult the factory; customer service phone numbers are in the back of this manual. Also see the entries below for Configure DGPS and Configure NMEA . To set Com P[...]

71 • GGA transmits time, position, and fix related data. • GSA and GSV transmits fix mode, DOP values, and satellites in view information. 4. Press ENT , then use ↑ ↓ → ← to enter the station frequency, then press ENT . 5. Press → to B IT R ATE | ENT then use ↑ ↓ to select the station bit rate, then press ENT . 6. A. If you are no[...]

72 To get to Coordinate System Selection: 1. Press MENU | MENU | ↓ to GPS S ETUP | ENT . 2. Press ↓ to C OORDINATE S YSTEM | ENT . This unit can show a position in degrees (36.14952°); degrees, minutes and thousandths of a minute (36° 28.700'); or degrees, minutes, seconds and tenths of a second (36° 28' 40.9"). It can also sh[...]

73 Configure Loran TD menu. Map Fix Map Fix is used with charts or maps. This system asks for a reference position in latitude/longitude, which you take from a marked location on the map. It then shows the present position as distance on the map from that reference point. For example, if it shows a distance of UP 4.00" and LEFT 0.50", you[...]

74 It's shown as a ratio, for example 1:24000. Press EXIT and the unit re- turns to the Configure Map Fix screen. Configure a map fix so the unit can find your position on a printed chart or topographical map. Press → to S ELECT O RIGIN | ENT | ENT | ENT to bring up the waypoint list. Select the waypoint that you saved the reference point un[...]

75 Customize Map Page While on the Map Page, press PAGES | ↓ or ↑ to select Option Name | ENT . DGPS Status The DGPS Status screen shows whether DGPS is off or on, and it de- scribes the quality of the DGPS signal. This screen is useful if you have to diagnose a DGPS problem. 1. Press MENU | MENU | ↓ to GPS S ETUP | ENT | ↓ to DGPS S TATUS [...]

76 to erase this menu. A message and tone appear periodically, warning you that the simulator is on. To turn the simulator off, repeat the above steps or turn the unit off. While in simulator mode, you can press EXIT to clear the steering and speed boxes from the screen while continuing the simulation. This will allow you to use the map cursor duri[...]

77 1. Press MENU | MENU | ↓ to GPS S ETUP | ENT | ENT . 2. A message appears, telling you to move the cursor near the desired location and press ENT . When the message automatically clears, follow the message instructions. 3. In a moment, your present position marker arrow appears on the map in the location you selected with the cursor. The unit [...]

78 Map Menu, left, Map Data Menu, right. Show Map Data From the Map Page, press MENU | ↓ to M AP D ATA | ENT . Press ENT to enter the E ARTH M AP D ETAIL selection list, and choose how much detail you want, from Off (so the unit operates like a GPS plotter) to High. After the option is set, press EXIT repeatedly to return to the page display.. Po[...]

79 100 mile zoom, the screen will show two rings with your current position in the center. The large ring touching the left and right sides of the screen is 100 miles in diameter (same as the zoom range). The second smaller ring is 50 miles in diameter (always 1/2 the zoom range). The distance from your current position to the smaller ring (the rin[...]

80 GPS Setup Menu, left, Map Datum Menu, right. Map Detail Category Selection This menu determines which of the mapping features are shown on the screen. This includes, waypoints, trails, icons, cities, highways, etc. You can selectively turn on or off any of these items, customizing the map to your needs. To get to Map Categories: 1. From the Map [...]

81 Map orientation at left is shown in north up and at right, track up. This is fine if you're always traveling due north. What you see to your left corresponds to the left side of the map, to your right is shown on the right side of the map, and so on. However, if you travel any other direction, the map doesn't line up with your view of [...]

82 NOTE: In North Up and Course Up, the present position arrow appears in the center of the map page. In Track Up, the position arrow appears centered in the lower third of the page. Navionics  Charts Your unit can display Navionics  electronic charts on MMCs. They work just like a MapCreate custom map on an MMC. Left, entrance to Chesapeake [...]

83 3. To turn off a Navionics chart, From the Map Page, press MENU | ↓ to M AP D ATA | ENT | ↓ to N AVIONICS M AP C HOICE | ENT . Use ↑ or ↓ to select L OWRANCE , then press ENT | EXIT | EXIT . Port Information Navionics charts contain Port Services information, represented by anchor icons on the map display. An example is displayed in the [...]

84 Port Services information screens. Tidal Current Information Navionics charts contain Tidal Current information, represented at large zoom ranges by a box icon with the letter " C ." The icon stands for a Tidal Current Station location. An example is displayed at right. When you zoom in to a sufficiently small zoom range, the icon itse[...]

85 Current Information screen. The Tidal Current Information screen displays daily tidal current data for this station on this date at the present time. The graph at the top of the screen is an approximate view of the flood and ebb pattern for the day, from midnight (MN), to noon (NN) to midnight (MN). The velocity scale at the top left side of the[...]

86 To view tide information: 1. Select a Tide Station icon: use the arrow keys to move the cursor over an icon. When it is selected, a pop-up name box appears. 2. After selecting the Tide Station icon, press WPT to display the Tide Information screen. Navionics chart showing Tide Station icon selected by cursor. In the example above, the tide is at[...]

87 approximate view of the tidal range pattern for the day, from midnight (MN), to noon (NN) to midnight (MN). The dotted line across the graph is the Mean Lower Low Water line (MLLW). The height scale on the top right side of the graph changes, based upon the maximum range of the tide for that day. The MLLW line also ad- justs its position as the [...]

88 The Position Pinning feature was developed so that when you stopped, the unit locked the present position on the GPS plotter until you moved a short distance or exceeded a very slow speed. The command remains available in the unit's software, but we recom- mend that you leave it in the default off (unchecked) mode. The "wan- dering&quo[...]

89 3. You can return to this command and press ENT again to turn the fea- ture off. GPS Setup command, left; Require DGPS command on the GPS Setup Menu, right. Screen Contrast and Brightness To access the Screen menu, press MENU | MENU | ENT . Once in the Screen menu: To adjust the display's contrast: The C ONTRAST slider bar is already select[...]

90 To adjust the screen's display mode: Press ↓ to D ISPLAY M ODE | ENT |press ↑ or ↓ to select mode | EXIT . Display Mode menu. Set Language This unit's menus are available in 10 languages: English, French, Ger- man, Spanish, Italian, Danish, Swedish, Russian, Dutch and Finnish. To select a different language: 1. Press MENU | MENU [...]

91 To set the Month: Press ↓ to M ONTH | ENT . Press ↑ or ↓ to select the month, then press ENT . To set the Day: Press → to D AY | ENT . Press ↑ or ↓ to select the day, then press ENT . To set the Year: Press → to Y EAR | ENT . Press ↑ or ↓ to select the year, then press ENT . The last field in this menu is C ONFIG DST . This fea[...]

92 System Setup command left; Software Information command, center. At right, the Software Information screen. 1. Press MENU | MENU | ↓ to S YSTEM S ETUP | ENT | ↓ to S OFTWARE I NFO | ENT . 2. Read the information displayed on the screen. 3. To return to the last page displayed, press EXIT | EXIT | EXIT . Sounds and Alarm Sound Styles Sounds t[...]

93 Track Smoothing This is a factory setting on the GPS Setup menu that should always be left on . When stopped or traveling at slow speeds (such as walking or trolling), Track Smoothing prevents wandering of trails, the steering arrow, compass rose and a map in track-up mode. Track Smoothing option, turned on. Trail Options There are several optio[...]

94 Update Trail Option This menu lets you change the way the trail updates occur. WARNING: If you uncheck the Update Trail option, automatic trail creation and recording will be turned off . You must turn it back on to record trails. The default setting is on. From the Trails Menu, press → to T RAIL O PTIONS | ENT . With U PDATE A CTIVE T RAIL hi[...]

95 Specific Trail Options Delete Trail To delete a specific trail: From the Trails Menu, press ↓ to Trail Name | ENT . The Edit Trail menu appears as seen in the following fig- ure. Press → to D ELETE T RAIL | ENT | ← to Y ES | ENT . Edit Trail menu. New Trail To manually start a new trail, in the Trails Menu, make sure N EW T RAIL is highlig[...]

96 System Setup Menu, left, Units of Measure Menu, right. To set Speed/Distance Unit of Measure: Press ↑ or ↓ to change the Speed/Distance, then press ENT . After the option is set, press EXIT | EXIT | EXIT to return to the page display. To set Heading: Press ↑ or ↓ to change the heading type, then press ENT . After the option is set, press[...]

97 Section 6: Searching NOTE: The background map loaded in your unit lets you to search for U.S. Interstate Highway exits and exit services, as well as some land features, including cities and lakes. For a full set of searchable land features, including landmarks, streets, addresses and Points of In- terest, you must load your own high-detail custo[...]

98 2. Press ENT to search in the Address field. 3. To enter an address number , press ↑ or ↓ to change the first number, then press → to move the cursor to the next number and re- peat until the number is correct, then press ENT . Find Address Menu. 4. To enter a street name , press ↓ to S TREET | ENT . There are two op- tions: A. You can s[...]

99 If you select yes, there are two options: A. You can spell out the city name in the top selection box. Press ↑ or ↓ to change the first letter, then press → to move the cursor to the next letter and repeat until the name is correct, then press ENT | ENT . B. Jump down to the lower selection list by pressing ENT , then press ↓ or ↑ to s[...]

100 Address search result list, left. At center, Map Page showing location of the address on the map, highlighted by cursor. At right, after the address is located, you can navigate to it ("D" symbol for destination). 8. To navigate to the address, press MENU | ENT | EXIT and the unit will begin showing navigation information to the addre[...]

101 A POI selected by the cursor, left, POI information screen, right. NOTE: Since the Go To Waypoint command is highlighted, you can navi- gate to the selected POI by pressing ENT | EXIT while in the POI Waypoint Information screen. Find Interstate Highway Exits 1. From the Map Page, press MENU | ↓ to H IGHWAY E XITS | ENT , which calls up the F[...]

102 Find By Name menu. 3. Once you have selected a highway name you can then select an exit. Press ↓ to switch to the Exit List, then press ↓ or ↑ until you highlight the exit, then press ENT. Find Exit menu, with an exit selected in the Exit List. 4. In the Exit Information screen you have two choices. A. Press ENT to navigate or "go to[...]

103 Tip: You can also look up some additional information on the Exit Serv- ices located near this exit. Press ↓ to S ERVICES |press ↓ or ↑ to select Service Name | ENT . Exit Information screen, left; general location and amenities information, at right. Find Map Places or Points of Interest (POI) 1. Press WPT , press ↓ or ↑ to select a [...]

104 appear. Press ↓ or ↑ to the selected POI and press ENT to call up the POI's Waypoint Information screen. Find by Nearest option, left, Calculating screen, center, POI list, right. 3. Search by name of POI. Press ENT . There are two options: A. You can spell out the POI in the top selection box. Press ↑ or ↓ to change the first lett[...]

105 "Go To" POI option, left, "Find on Map" POI option, right. Find Streets or Intersections Find a Street 1. From the Map Page, press MENU | ↓ to F IND S TREETS | ENT and the Find Streets Menu appears. Find Streets command, left, Find Streets menu, right. 2. You must first fill in a street name in the First Street dialog box.[...]

106 Find Street By Name menu. Spell out name in the top box, or select from the list in the lower box. 3. The Find Streets menu reappears with the street you're searching for in the First Street box. (In this example, it's 80th Street.) To search for that street, press ↓ to F IND F IRST S TREET | ENT . A message appears asking you to wa[...]

107 Map Page showing results of a street search. The cursor points to the located street. If you want to navigate to the found street at the cursor location, just press MENU | ENT | EXIT . Find an Intersection You must enter one street in the First Street dialog box and enter the next street in the Second Street dialog box. 1. From the Map Page, pr[...]

108 5. The Find Streets menu reappears with the first and second street dialog boxes filled in. In this example, we selected 71st Avenue as our second street. You could now use similar techniques to select a city or Zip code, but your search will probably be faster if you leave those boxes blank. (You can specify a city and/or Zip code later on to [...]

109 If you want to navigate to the found intersection, just press MENU | ENT | EXIT . Find Waypoints 1. Press WPT | ENT . 2. If searching for the waypoint By Name , press ENT . If searching for the Nearest waypoint, press ↓ to N EAREST | ENT . (To search by name, jump to step 5.) Find Waypoint menu, left; Find By Nearest command, center, Find by [...]

110 Waypoint Information screens with the Go To Waypoint command se- lected, left, and the Find on Map command selected, right. To clear these menus and return to the previous page, press EXIT re- peatedly. 5. If you're looking by name , there are two options: A. You can spell out the name in the top selection box. Press ↑ or ↓ to change t[...]

111 Section 7: Supplemental Material Datums Used by This Unit WGS 1984 Default Adindan Mean for Ethiopia, Sudan Adindan Burkina Faso Adindan Cameroon Adindan Ethiopia Adindan Mali Adindan Senegal Adindan Sudan Afgooye Somalia Ain el Abd 1970 Bahrain Ain el Abd 1970 Saudi Arabia Anna 1 Astro 1965 Cocos Islands Antigua Island Astro 1943; Antigua (Lee[...]

112 Chua Astro Paraguay Corrego Alegre Brazil Dabola Guinea Djakarta (Batavia) Indonesia (Sumatra) DOS 1968 New Georgia Islands (Gizo Island) Easter Island 1967 Easter Island European 1950 Mean for Austria, Belgium, Denmark, Finland, France, West Germany, Gi- braltar, Greece, Italy, Luxembourg, Neth- erlands, Norway, Portugal, Spain, Sweden, Switze[...]

113 Naparima BWI Trinidad & Tobago North American 1927 Mean for Antigua, Barbados, Barbuda, Caicos Islands, Cuba, Dominican Republic, Grand Cayman, Jamaica, Turks Islands North American 1927 Mean for Belize, Costa Rica, El Sal- vador, Guatemala, Honduras, Nicaragua North American 1927 Mean for Canada North American 1927 Mean for CONUS (Continen[...]

114 Point 58 Sweden Santo (DOS) 1965 Espirito Santo Island Sao Braz Azores (Sao Miguel, Santa Maria Islands) Sapper Hill 1943 East Falkland Island Schwarzeck Nambia Selvagem Grande Salvage Islands SGS 85 Soviet Geodetic System 1985 South American 1969 Mean for Argentina, Bolivia, Brazil, Chile, Colombia, Ecuador, Guyana, Paraguay, Peru, Trinidad &a[...]

115 FCC Compliance This device complies with Part 15 of the U.S. Federal Communi- cations Commission (FCC) Rules. Operation is subject to the fol- lowing two conditions: (1) this device may not cause harmful in- terference, and (2) this device must accept any interference re- ceived, including interference that may cause undesired opera- tion. Chan[...]

116 Notes[...]

117 Index A Accessories, 1, 3, 4, 6, 11, 16, 17, 21, 32, 50, 97 Sec. 2, Installation & Accessories , 11 Alarm Clock, 63 Alarms, 25, 35, 48, 50, 61, 67, 68, 76 Anchor Alarm, 67, 68 Antenna, 1, 3, 4, 11, 12, 17, 18, 19, 35, 36, 115 Arrival Alarm, 35, 48, 50, 61, 67, 68, 76 B Backlights / Lighting, 2, 23 Batteries, 11, 13, 14, 15, 19, 20 Brightnes[...]

118 49, 55, 58, 60, 68 A Route, 60 A Trail, 47 Cancel, 25, 35, 43, 44, 48, 50, 52, 60 To Cursor Position, 43 To Icon, 55 Nearest, 37, 38, 41, 97, 103, 104, 109 NMEA, 12, 15, 16, 69, 70, 71 O Off Course Alarm, 67 P Page Displays, 2, 25, 26, 33, 34, 35, 75 Digital Data, 33 Map, 9, 23, 24, 26, 29, 30, 31, 33, 34, 35, 41, 42, 43, 44, 47, 48, 53, 55, 56[...]

119 101, 103, 104, 109, 110 Delete, 63 Edit, 64 Search, 109 Select, 64 Z Zooming, 4, 24, 29, 30, 35, 36, 47, 57, 77 Auto Zoom, 77[...]

120 Notes[...]

121 LOWRANCE DATABASES LICENSE AGREEMENT THIS IS A LEGAL AGREEMENT BETWEEN THE END-USER WHO FIRST PURCHASES THIS PRODUCT AS A CONSUMER ITEM FOR PERSONAL, FAMILY, OR HOUSEHOLD USE ("YOU") AND LOWRANCE ELECTRONICS, INC., THE MANUFACTURER OF THIS PRODUCT ("WE", "OUR", OR "US"). USING THE PRODUCT ACCOMPANIED BY T[...]

122 DATABASES LIMITED WARRANTY "We", "our", or "us" refers to Lowrance Electronics, Inc., the manufacturer of this product. "You" or "your" refers to the first person who purchases the prod- uct as a consumer item for personal, family, or household use. The Databases Limited Warranty applies to the [...]

123 LOWRANCE ELECTRONICS FULL ONE-YEAR WARRANTY "We," "our," or "us" refers to LOWRANCE ELECTRONICS, INC., the manufacturer of this product. "You" or "your" refers to the first person who purchases this product as a consumer item for personal, family or household use. We warrant this product against[...]

124 How to Obtain Service… …in the USA: We back your investment in quality products with quick, expert service and genuine Lowrance parts. If you're in the United States and you have technical, return or repair questions, please contact the Factory Customer Service Department. Before any product can be returned, you must call customer serv[...]

Accessory Ordering Information for all countries To order Lowrance GPS accessories such as computer cables or MMC cards, please contact: 1) Your local marine dealer or consumer electronics store. Most quality dealers that handle marine electronic equipment or other consumer electronics should be able to assist you with these items. To locate a Lowr[...]

Visit our web site: Lowrance Pub. 988-0151-191 © Copyright 2003 All Rights Reserved Printed in USA 121903 Lowrance Electronics, Inc.[...]