English dropdown-ico

Makita BHR241RFE manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Makita BHR241RFE, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Makita BHR241RFE one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Makita BHR241RFE. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Makita BHR241RFE should contain:
- informations concerning technical data of Makita BHR241RFE
- name of the manufacturer and a year of construction of the Makita BHR241RFE item
- rules of operation, control and maintenance of the Makita BHR241RFE item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Makita BHR241RFE alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Makita BHR241RFE, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Makita service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Makita BHR241RFE.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Makita BHR241RFE item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    Max. Output(W) Battery V oltage: V Cell and Capacity Capacity : mm ( " ) Charging Time: min. 330 0 - 1,100 0 - 4,000 18 Li-ion 3.0 Ah Y es Y es Y es Y es 10 (3/8) 13 (1/2) 26 (1-1/16) 20 (13/16) 3.2 (7.0) including Battery BL1830 [3.5 (7.7) measured by EPT A regulation] 22 with DC18RA Models No. Description PR ODUCT T ECHNICAL INFORMA TION C O[...]

  • Page 2

    P 2 / 1 4 [1] NECESSAR Y REP AIRING T OOLS CA UTION: Remov e the battery and the bit from the machine f or safety befor e repair/ maintenance in accordance with the instruction manual! R epair Description Code No. 1R003 Retaining ring S pliers SR-2 Removing / Installing Ring spring 19 Removing Ring spring 29 Removing Helical gear 25 from Cam shaft [...]

  • Page 3

    [2] LUBRICA TION (cont.) R epair P 3 / 1 4 Fig. 2 Item No. Description Portion to lubricate Lubricant Amount Striker Ball bearing 606ZZ Compression spring 7 Disassemble T ool holder section as illustrated in Fig. 3 . Retaining ring S-7 Piston joint Armature Flat washer 12 Swash Bearing Section 40 41 51 52 53 63 (f) (g) (h) (g) (k) Crank room (i) (j[...]

  • Page 4

    R epair P 4 / 1 4 [3] DISASSEMBL Y/ASSEMBL Y [3] -2. Change Lev er DISASSEMBLING ASSEMBLING Change le ver Drill mode Lock button Pushing Lock button into Change le ver , turn Change le ver fully to Drill mode until it stops. Remov e Change lever by le vering up it with Slotted head scre wdriv er, inserted between Gear housing complete and Change le[...]

  • Page 5

    R epair P 5 / 1 4 bearing room of Gear housing complete 4x40 T apping screws (4 pcs.) Gear housing complete Holder cap cov er Motor housing complete Ball bearing 6000DD W of Armature (behind the Fan) [3] DISASSEMBL Y/ASSEMBL Y [3] -4. Armature 1) Remov e Holder cap cover by inserting Slotted scre wdriver between Holder cap co ver and Motor housing [...]

  • Page 6

    R epair P 6 / 1 4 [3] DISASSEMBL Y/ ASSEMBL Y [3] -5. T orque Limiter Section (cont.) ASSEMBLING Do the rev erse of disassembling steps. Note: Do not forget to assemble Flat w asher 28 between T orque limiter section and Inner housing complete. Refer to Fig. 12 . [3] DISASSEMBL Y/ASSEMBL Y [3] -6. Needle Bearing Complete and Oil Seal 25 DISASSEMBLI[...]

  • Page 7

    R epair P 7 / 1 4 DISASSEMBLI NG 1) Referring to " [3] -5. T orque Limiter Section ", disassemble Ring spring 29, W asher 31, Compression spring 32 and Spur gear 51 from T ool holder complete. Refer to Figs. 11 to 14 . 2) Holding Gear housing complete in vise and 1R038, T ap Ring spring 28 in T ool holder complete as illustrated in Figs. [...]

  • Page 8

    [3] DISASSEMBL Y/ASSEMBL Y [3] -7. Impact Bolt Section (cont.) DISASSEMBLING ASSEMBLING Fig. 29 Note: Use an extra Piston c ylinder as a jig. Never use Piston c ylinder that is to be assembled to the machine. 2) Push Ring spring 28 with Piston cylinder until it f its to the inner groove of T ool holder complete. ( Fig. 29 ) 1) Disassemble T ool hol[...]

  • Page 9

    [3] DISASSEMBL Y/ASSEMBL Y [3] -8. Swash Bearing Section (cont.) DISASSEMBLING Fig. 32 Fig. 33 6) Mov e Piston cylinder to the rear dead center position ( Fig. 32 ). 7) Remov e Swash bearing section from Inner housing by pulling in the direction of the arrow . Then, remov e Change plate from the groov e of Clutch cam. ( Fig. 33 ). Piston cylinder S[...]

  • Page 10

    [3] DISASSEMBL Y/ASSEMBL Y [3] -8. Swash Bearing Section (cont.) DISASSEMBLING ASSEMBLING 1R032 1R033 Fig. 39 Swash bearing 10 Helical gear 26 Retaining ring S-7 Compression spring 7 Spur gear 10 Cam shaft Cam shaft Clutch cam 1) Assemble Swash bearing section using 1R032, 1R033, 1R291 and arbor press as illustrated in Fig. 39 . Note: Be sure to pu[...]

  • Page 11

    [[3] DISASSEMBL Y/ASSEMBL Y [3] -8. Swash Bearing Section (cont.) R epair ASSEMBLING P 1 1 / 1 4 4) Mov e Piston cylinder to the rear dead center position. ( Fig. 42 ) 5) Insert the pole of Swash bearing 10 into the hole of Piston joint as illustrated in Fig. 43 . 6) Insert Ring 8 (the end of Swash bearing section) into Inner housing complete. ( Fi[...]

  • Page 12

    R epair ov al hole of F/R change le ver protrusion of Switch P 1 2 / 1 4 [3] DISASSEMBL Y/ASSEMBL Y [3]-9. F/R change lev er , W ave washer , Cushion and Rubber pin 5 in Housing set Fit the protrusion of Switch into Ov al hole of F/R change lev er and assemble them to Housing L. ASSEMBLING Refer to Fig. 47 . Rubber pin 5 Pass Pin 1.5 through Rubber[...]

  • Page 13

    P 1 3 / 1 4 M aintenance program It is recommended to replace the f ollowing parts sho wn below and apply lubricant to the specific parts designated in Figs.2 and 3 when replacing Carbon brushes. 1 Cap 35 40 O ring 16 38 Ring spring 28 29 Steel ball 7.0 35 Cushion ring 13 37 O ring 9 C ircuit diagram Red Blue Brush holder (L) Brush holder (R) Y ell[...]

  • Page 14

    P 1 4 / 1 4 W iring diagram Brush holder Rib A Route all of the FET lead wires on the right side of Rib A. T erminal Heat sink FET Y oke unit Bend Connecting terminal to Housing set (L) side as illustrated abov e. Switch Fix the Brush holder’ s Lead wires (red and black) with Lead wire holder . Switch Put the extra portion of Lead wires in this a[...]