Go to page of
Similar user manuals
-
Home Theater System
MartinLogan 1000
20 pages 1.21 mb -
Home Theater System
MartinLogan MLT-2
20 pages 1.23 mb -
Home Theater System
MartinLogan MLT-1
20 pages 0.44 mb -
Home Theater System
MartinLogan E2
32 pages 2.81 mb -
Home Theater System
MartinLogan 20
1 pages 0.33 mb -
Home Theater System
MartinLogan ESL Series
1 pages 0.98 mb -
Home Theater System
MartinLogan Home Theater System
28 pages 0.23 mb -
Home Theater System
MartinLogan 300
28 pages 1.04 mb
A good user manual
The rules should oblige the seller to give the purchaser an operating instrucion of MartinLogan E2, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.
What is an instruction?
The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of MartinLogan E2 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.
Unfortunately, only a few customers devote their time to read an instruction of MartinLogan E2. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.
What should a perfect user manual contain?
First and foremost, an user manual of MartinLogan E2 should contain:
- informations concerning technical data of MartinLogan E2
- name of the manufacturer and a year of construction of the MartinLogan E2 item
- rules of operation, control and maintenance of the MartinLogan E2 item
- safety signs and mark certificates which confirm compatibility with appropriate standards
Why don't we read the manuals?
Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of MartinLogan E2 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of MartinLogan E2, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the MartinLogan service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of MartinLogan E2.
Why one should read the manuals?
It is mostly in the manuals where we will find the details concerning construction and possibility of the MartinLogan E2 item, and its use of respective accessory, as well as information concerning all the functions and facilities.
After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.
Table of contents for the manual
-
Page 1
S T A TEMENT TM E2 setup manual M ART I N L OGA N ® the loudspeaker technology company[...]
-
Page 2
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Before Y ou Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Master P acking List Required T ools Unpacking the Statement e2 Speak er Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Initial Speaker Placement The W all Behind the [...]
-
Page 3
Before Y ou Begin 3 Master P acking List Required T ools Before you being setting up the Statement e2, please make sure that all 15 crates/boxes are present and accounted for . The list below gives a detailed description of what can be found in each numbered crate/box. # Contents Sub (Left) 1 Master Sub, Left 2 Middle Sub, Left 3 Middle Sub, Left 4[...]
-
Page 4
4 Speaker Placement F or optimal performance of the Statement e2 system we recommend that the ESL/T ransition towers be placed approximately five to seven feet from the front wall (the wall in front of the listening position) and at least two feet from the side walls. The subwoofer towers should be placed diagonally (or against a wall) in the front[...]
-
Page 5
Assembly 5 WARNING! Assembling the Statement e2 requires two people , except for step 12 of the subwoofer tower assembly , which requires three people . Do not attempt any part of the assembly process with one person. 1 Place the primary subwoofer module in position on the floor , (the primary module has 10 binding posts). Corner placement is recom[...]
-
Page 6
6 Assembly 4 After the second module is in position atop the primary module, place a level on it as shown. Level the module front to back by inserting a small allen wrench (or other suitable instrument) through the hole in the cones on the base of the module (detail), and rotating the cone up or down to achieve level. 5 Level the module left to rig[...]
-
Page 7
Assembly 7 7 Stack the next secondary module atop the second uti- lizing the same assembly procedure used in step 3. 8 Align the cones to the indentations on the cabinet below , and level the module front-to-back and left-to- right, following the same procedure used in steps 4 and 5. 9 Repeat the procedure in step 6. Figure 8 Figure 9 Figure 10[...]
-
Page 8
8 Assembly 10 Place the fourth and final module in position (repeat- ing steps 3 thru 6). The top module is distinguished from the other modules by the lack of mounting holes on the top bracket (as shown). 11 Align the slots on the top and bottom of the grill cloth frames with the curved extrusion on the module. Place firmly into position so that t[...]
-
Page 9
Assembly 9 1 2 Install woofer wiring harness as shown. Y ou can move the tower to the preferred listening position by shifting the unit from side to side and “walking” it. 13 When you are confident the sub tower is correctly positioned, mark the floor with masking tape at each corner . Install the spikes by using a safe dolly to tip the sub tow[...]
-
Page 10
10 Assembly Note: The following instructions describe the assembly of the right channel high-and mid-frequency tower . Duplicate all assembly instructions for the left tower assembly . 1 Attach the outside (semi-circle shaped) trim rail to the transition tower by aligning the five pins on the trim rail with the 5 cam holes in the tower . 2 Use a ph[...]
-
Page 11
Assembly 11 4 Install the inside wing (wedge shaped with pins on the side) trim rail by aligning the 5 pins with the corre- sponding cams as in the previous assembly , only this time the cams turn clockwise to lock in the trim wing . 5 F inished transition tower assembly . Figure 18 Figure 19[...]
-
Page 12
12 Assembly 6 Pick up the transition tower assembly and insert it as shown into the base so the three holes in the mounting bracket line up with the holes in the tower . 7 P ush the tower towards the center for proper align- ment. 8 Once the holes are properly aligned, insert the 3 1 / 2 ” x 9 / 16 ” hex head lag screws through a steel washer a[...]
-
Page 13
Assembly 13 9 Use a level to bring the tower 90 degrees vertical left to right. 10 When the tower is perfectly plumb, go ahead and tighten the bolts securely . 11 Use your level to plumb the tower front to back. Figure 23 Figure 24 Figure 25[...]
-
Page 14
14 Assembly 12 T ighten tower wing bolt. 13 T ighten base bolts. 14 Connect the tower as shown (red to red, black to black). Figure 26 Figure 27 Figure 28[...]
-
Page 15
Assembly 15 15 Install the ESL wing trim (wedge shaped with pins on the narrow end) by aligning the 5 pins with the corre- sponding cams. The cams turn clockwise to lock the trim with in place. 16 Insert the electrostatic panel as shown. 17 Line up holes and insert the 2 1 / 4 ” x 9 / 16 ” button head cap screws (black) through a steel washer a[...]
-
Page 16
16 Assembly 18 Use a level to plumb the electrostatic panel left-to- right. 19 Measure the space between towers (top and bottom). The space should measure exactly 2 inches. 20 T ighten frame bolts as shown. Figure 32 Figure 33 Figure 34[...]
-
Page 17
Assembly 17 21 Use a level to plumb the electrostatic panel front-to- back. 22 T ighten wing bolts. 23 T ighten base bolts. Figure 35 Figure 36 Figure 37[...]
-
Page 18
18 Assembly 24 Connect light bar 25 Connect electrostatic panel wires to the color-coded screw-terminal connector . 26 ESL panel properly connected. Figure 38 Figure 39 Figure 40[...]
-
Page 19
Assembly 19 27 F ind the loops at the top of the transition tower grill sock. 28 Hook the loops as indicated at the top of the tower . 29 Hook the loops on the bottom of the sock on the bottom of the tower as indicated. Figure 41 Figure 42 Figure 43[...]
-
Page 20
20 Assembly 30 Push the grill sock into the slot provided to stretch the cloth taut, from top to bottom. 31 Place the top of the base into position. Note: Y ou may want to wait before installing the top of the base as settings inside the base may need changing . Figure 44 Figure 45[...]
-
Page 21
Connections—Exos Crossover Inputs 21 Connect the outputs of the Preamplifier/Processor to the inputs of the EXOS using either balanced or single ended connections. There are right channel, left channel and optional 0.1 effects channel inputs. WARNING! Use either all balanced or all single ended connections for signal inputs. Do not use both. C ON[...]
-
Page 22
22 Connections—Exos Crossover Outputs Connect the EXOS subwoofer outputs to the amplifier(s) for the woofer towers using either balanced or single ended connections. Both the balanced and single ended outputs are always on—you can use either option to con- nect the woofer tower amplifier(s) regardless of which you used for signal input. Note: U[...]
-
Page 23
This method of connection uses individual runs of speaker wire from your amplifier . This doubles the signal carrying conductors from the amplifier to the speaker , thus direct- coupling each portion of the crossover to the amplifier . Connect one set of wires to the upper set of binding posts which connect to the ESL panel of the Statement e2. The[...]
-
Page 24
The very nature of vertical bi-amping dictates that both amplifiers be identical. With vertical bi-amping , each of the stereo amplifiers is dedicated to one speaker . F or instance, the left channel of each amplifier drives the low pass (T ransition) section while the right channel drives the high pass (ESL) section. Starting with one speaker , co[...]
-
Page 25
Connections—Subwoofer T owers 25 This connection method is safe for all amplifiers (see figure 51). 2-Ohm Connection This connection is the loudest, but draws the most power from the amplifier (see figure 52). If using this connection method, make sure your amp can handle 2- Ohms. Use this connection method if you wish to use two ampli- fiers to [...]
-
Page 26
The passive high-pass settings can be adjusted by changing the red and black jumpers found in the high-pass section of the ESL/T ransition tower passive crossover . WARNING! Before changing the passive-high pass options be sure to turn the amps off and unplug the Statement e2 ESL/T ransition tower . The design of these jumpers accommodates differen[...]
-
Page 27
Figure 60. Jumper settings for all-open mode. Figure 61. Jumper settings for 15-foot mode. Figure 58. Jumper settings for 10-foot mode. Figure 56. Open (not connected) jumpers. Figure 57. Closed (connected) jumpers. Figure 59. Jumper settings for all-closed mode. P assive High-P ass Settings 27[...]
-
Page 28
28 AC P ower Connections Because your MartinLogan Statement e2 ESL/T ransition towers use an internal power supply to energize their elec- trostatic cells with high-voltage DC, they must be connected to an AC power source. The EXOS crossover must also be connected to an AC power source. F or this reason the prop- er IEC standard power cords are pro[...]
-
Page 29
Now that you know all the connection options and how to set them, it’s time to make the speakers work in their target environment. F or this part, it is recommended that an audio analyzer be used (RT A or a computer based instrument). Start with default settings. Look at the 200Hz to 500Hz area of the ESL-transition tower alone. If there is too m[...]
-
Page 30
Y ou will need to set the dip switches for both right and left channel. Note: Only one dip switch per dip switch cluster should be on at a time. 5 If available, use test equipment to optimize the sub- woofer response. 6 The 50Hz control works the same as the 25Hz control. 7 The phase settings allow the phase of the woofer sec- tion to be modified i[...]
-
Page 31
T oe in the ESL/T ransition towers so the listener is looking at the inner 1 / 3 of the ESL panels. Sitting at the listening posi- tion, hold a flashlight under your chin and point i t a t each speaker . The reflection of the flashlight should be 1 / 3 of the way out from the inner edge of the panel (see figure 68). Viewed from the listening positi[...]
-
Page 32
2101 Delaware Street, Lawrence, Kansas 66046, USA tel 785.749.0133 fax 785.749.5320 www.martinlogan.com ©2003 MartinLogan, All rights reserved Rev. #100203 M ART I N L OGA N ® the loudspeaker technology company[...]