Mazda 2008 Tribute manual

Introduction 4 Instrument Cluster 12 W arning lights and chimes 12 Gauges 17 Entertainment Systems 19 Auxiliary input jack 25 Climate Controls 29 Manual heating and air conditioning 29 Rear window defroster 31 Lights 32 Headlamps 32 T urn signal control 35 Bulb replacement 36 Driver Controls 42 W indshield wiper/washer control 42 Steering wheel adj[...]

Tires, Wheels and Loading 125 T ire information 127 T ire inflation 130 T ire Pressure Monitoring System (TPMS) 143 V ehicle loading 148 T railer towing 154 Recreational towing 160 Driving 161 Starting 161 Brakes 166 Electronic stability control 168 T ransmission operation 173 Roadside Emergencies 188 Hazard flasher switch 188 Fuel pump shut-off sw[...]

Maintenance and Specifications 232 Engine compartment 240 Engine oil 244 Battery 248 Engine coolant 250 Fuel information 256 Air filter(s) 269 Maintenance product specifications and capacities 271 Engine data 273 Accessories 276 Index 277 All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or b[...]

CALIFORNIA Proposition 65 W arning W ARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemic[...]

W ARNING: In the event of an accident the Fuel pump shut-off switch will automatically cut off the fuel supply to the engine. The switch can also be activated through sudden vibration (e.g. collision when parking). T o reset the switch, refer to the Fuel pump shut-off switch in the Roadside Emergencies chapter . SAFETY AND ENVIRONMENT PROTECTION W [...]

BREAKING-IN YOUR VEHICLE There are no particular breaking-in rules for your vehicle. During the first 1,000 miles (1,600 km) of driving, vary speeds frequently . This is necessary to give the moving parts a chance to break in. SPECIAL NOTICES Event Data Recorder The computer in your vehicle is capable of recording detailed data potentially includin[...]

Emission warranty The New V ehicle Limited W arranty includes Bumper to Bumper Coverage, Safety Restraint Coverage and Corrosion Coverage. In addition, your vehicle is eligible for Emissions Defect and Emissions Performance W arranties. For a detailed description of what is covered and what is not covered, refer to the W arranty Information Booklet[...]

These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner’ s Manual Protecting the Environment Fasten Seat Belt Airbag - Front Airbag - Side Passenger Airbag Off Child Seat Lower Anchor Child Seat T ether Anchor Brake System Anti-Lock Brake System Parking Brake System Brake Fluid - Non-Petroleum Ba[...]

V ehicle Symbol Glossary Rear W indow Defrost/Demist Power W indows Power W indow Lockout Personal Alarm System Feature Engine Oil Engine Coolant Engine Coolant T emperature Do Not Open When Hot Battery A void Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan W arning Power Steering Fluid Maintain Correct Fluid Level MAX MIN Emission System[...]

Multi-function lever (pg. 42) Instrument cluster (pg. 12) Hazard flasher control (pg. 188) Headlamp control (pg. 32) Parking brake release (pg. 167) Speed controls* (pg. 49) Hood release (pg. 239) Steering wheel controls* (pg. 52) * if equipped 2008 Tribute (j14) Owners Guide (post-2002-fmt) USA (fus) Instrument Cluster 10[...]

Climate controls (pg. 29) Audio system (pg. 19) Auxiliary input jack (pg. 25) Electronic stability control (pg. 168) Auxiliary power point (pg. 46) *if equipped 2008 Tribute (j14) Owners Guide (post-2002-fmt) USA (fus) Instrument Cluster 11[...]

W ARNING LIGHTS AND CHIMES W arning lights and gauges can alert you to a vehicle condition that may become serious enough to cause extensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’ s functions. Many lights will illuminate when you start your vehicle to make sure the bulbs work. If any light remains [...]

W ARNING: Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter , the fuel system, interior floor coverings or other vehicle components, possibly causing a fire. Check fuel cap: Momentarily illuminates when the ignition is turned to the RUN position to ensure your bulb is working. When the light stays [...]

Anti-lock brake system (ABS): If the ABS light stays illuminated or continues to flash, a malfunction has been detected, have the system serviced immediately by an authorized Mazda dealer . Normal braking is still functional unless the brake system warning light also is illuminated. W ARNING: If the light remains on, continues to flash or fails to [...]

T raction Control 娂 : Illuminates when the T raction Control 娂 is active. If the light remains on, have the system serviced immediately , refer to the Driving chapter for more information. Low tire pressure warning: Illuminates when your tire pressure is low . If the light remains ON at start up or while driving, the tire pressure should be che[...]

Anti-theft system: Flashes when the SecuriLock 娂 Passive Anti-theft System has been activated. Throttle control/Powertrain: Illuminates when a powertrain fault has been detected. Contact your authorized dealer as soon as possible. Door ajar: Illuminates when the ignition is in the RUN position and any door is open. T urn signal: Illuminates when [...]

GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the e[...]

Odometer: Registers the total miles (kilometers) of the vehicle. T rip odometer: Registers the miles (kilometers) of individual journeys. T o reset, tap on the trip SELECT/RESET button to toggle the display between the TRIP A and TRIP B. Holding the SELECT/RESET button for two seconds will reset the trip odometer to zero. T achometer: Indicates the[...]

AUDIO SYSTEMS AM/FM/single CD/in-dash CD6/MP3 sound system Accessory delay: Y our vehicle is equipped with accessory delay . W ith this feature, the window switches, radio and moon roof (if equipped) may be used for up to ten minutes after the ignition is turned off or until either front door is opened. Note: Y our vehicle is equipped with a unique[...]

the system will reload the disc. T o auto eject all loaded discs, press and hold EJECT . The system will eject all discs and prompt you when to remove them. 2. MEMOR Y PRESETS:In radio mode, to set a station, select the desired frequency band, AM, FM1 or FM2. T une to the desired station. Press and hold a preset button until sound returns and PRESE[...]

Adjust 1–7: Increasing this setting from 1 (lowest setting) to 7 (highest setting) allows the radio volume to automatically change slightly with vehicle speed to compensate for road and wind noise. Recommended level is 1–3; SPEED OFF turns the feature off and level 7 is the maximum setting. ALL SEA TS (Occupancy mode, if equipped): Press SOUND [...]

the display . Then press SEEK/TRACK to find the next station playing that category of music or SCAN for a brief sampling of all stations playing that category of music. COMPRESSION: A vailable only in CD/MP3 mode. Press MENU until COMPRESSION ON/OFF appears in the display . Use SEEK/TRACK to toggle ON/OFF . When COMPRESSION is ON, the system will b[...]

13. CA T (Category) /FOLD (Folder):In Category mode, use to select from various music categories. T o change RDS categories, ensure that RDS is ON in the Menu listing. Press MENU again until RDS ON appears in the display . Press CA T . PRESS UP OR DOWN TO CHANGE RDS CA TEGORY will appear in the display . Press SEEK/TRACK to scroll through all possi[...]

16. SCAN:In radio mode, press for a brief sampling of all strong radio stations. In CD/MP3 mode, press for a brief sampling of all tracks on the current disc or folder . 17. DIRECT : Press to access the desired radio station, track or MP3 folder . In radio mode, press DIRECT and then press the desired radio frequency (i.e. 101.1) using the memory p[...]

Auxiliary input jack Y our vehicle is equipped with an Auxiliary Input Jack (AIJ). The Auxiliary Input Jack provides a way to connect your portable music player to the in-vehicle audio system. This allows the audio from a portable music player to be played through the vehicle speakers with high fidelity . T o achieve optimal performance, please obs[...]

6. Press AUX on the vehicle radio repeatedly until LINE IN appears in the display . Y ou should hear audio from your portable music player although it may be low . 7. Adjust the sound on your portable music player until it reaches the level of the FM station or CD by switching back and forth between the AUX and FM or CD controls. T roubleshooting: [...]

Radio reception factors: There are three factors that can affect radio reception: • Distance/strength: The further you travel from an FM station, the weaker the signal and the weaker the reception. • T errain: Hills, mountains, tall buildings, power lines, electric fences, traffic lights and thunderstorms can interfere with your reception. • [...]

Do not use any irregular shaped CDs or discs with a scratch protection film attached. CDs with homemade paper (adhesive) labels should not be inserted into the CD player as the label may peel and cause the CD to become jammed. It is recommended that homemade CDs be identified with permanent felt tip marker rather than adhesive labels. Ballpoint pen[...]

MANUAL HEATING AND AIR CONDITIONING SYSTEM 1. Fan speed adjustment: Controls the volume of air circulated in the vehicle. 2. R Rear defroster: Press to activate/deactivate the rear window defroster . Refer to Rear window defroster later in this chapter for more information. 3. Defrost: Distributes outside air through the windshield defroster vents [...]

10. Passenger heated seat control (if equipped): Press to activate/deactivate the passenger heated seat. See Heated seats in the Seating and Safety Restraints chapter . 11. Recirculated air: Press to activate/deactivate air recirculation in the vehicle. Recirculated air may reduce the amount of time needed to cool down the interior of the vehicle a[...]

For maximum cooling performance in MAX A/C mode: 1. Select MAX A/C. 2. Move temperature control selector to the coolest setting. 3. Set the fan to the highest speed initially , then adjust to maintain comfort. T o aid in side window defogging/demisting in cold weather: 1. Select . 2. Select A/C. 3. Adjust the temperature control to maintain comfort[...]

HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to turn on the headlamps. Foglamp control (if equipped) The headlamp control also operates the foglamps. The foglamps can be turned on when the headlamp control is in the , or positions and the high beams are not turned on.[...]

Flash to pass Pull toward you slightly to activate and release to deactivate. Daytime running lamps (DRL) (if equipped) T urns the lowbeam headlamps on with a reduced output. T o activate: • the ignition must be in the 3 (RUN) position. • the headlamp control must be in the OFF , parking lamps or autolamp position. • with automatic transmissi[...]

AIMING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant. If your vehicle has been in an accident the alignment of your headlamps should be checked by your authorized dealer . V ertical aim adjustment 1. Park the vehicle directly in front of a wall or screen on a level surface, approximately 25 feet (7.6 meters) a[...]

5. Locate the vertical adjuster on the headlamp, then us ea4m m socket to turn the adjuster either counterclockwise (to adjust up) or clockwise (to adjust down) aligning the upper edge of the light pattern to the horizontal line. 6. Move the opaque cloth to cover the right-hand headlamp and repeat Steps 4 and 5 for the left-hand headlamp. 7. HORIZO[...]

Dome lamps and map lamps The front dome lamp is located overhead between the driver and passenger seats. The dome lamp control has three positions: • OFF: In this position, the lamp will not illuminate. • DOOR: In this position, the dome lamp will illuminate only when a door is opened and will remain illuminated for 25 seconds after the door is[...]

Using the right bulbs Replacement bulbs are specified in the chart below . Headlamp bulbs must be marked with an authorized “D.O.T .” for North America to ensure lamp performance, light brightness and pattern and safe visibility . Note: The correct bulbs will not damage the lamp assembly or void the lamp assembly warranty and will provide quali[...]

Replacing headlamp bulbs 1. Make sure that the headlamp control is in the OFF position. 2. Open the hood. 3. Reach over the front bolster . 4. Remove the bulb by turning it counterclockwise and then pulling it straight out. W ARNING: Handling Halogen Bulbs: When a halogen bulb breaks, it is dangerous. These bulbs contain pressurized gas. If one is [...]

Replacing tail/stop/turn/backup lamp bulbs The tail/stop/turn/sidemarker/backup lamp bulbs are located in the same portion of the tail lamp assembly , one just below the other . Follow the same steps to replace either bulb: 1. Make sure the headlamp switch is in the OFF position and then open the liftgate to expose the lamp assembly screws. 2. Remo[...]

4. Pull bulb straight out of socket and push in the new bulb. 5. Install the bulb socket into the lamp assembly and rotate clockwise. 6. T o install, carefully press the lamp assembly into liftgate. Replacing high-mount brake lamp bulbs T o remove the lamp assembly: 1. Remove the two screws and move the lamp assembly away from the liftgate. 2. Remo[...]

Replacing foglamp bulbs (if equipped) 1. Make sure the foglamp switch is in the OFF position. 2. From underneath the vehicle, rotate the harness/bulb assembly counterclockwise, to remove from the fog lamp. 3. Carefully disconnect the bulb from the harness assembly via the two snap clips. Install the new bulb in reverse order . 2008 Tribute (j14) Ow[...]

MULTI-FUNCTION LEVER W indshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers. W indshield washer: Push the end of the stalk: • briefly: causes a single swipe of the wipers without washer fluid. • a quick push and hold: the wipers will swipe three [...]

For rear wash cycle, rotate (and hold as desired) the rear wiper/washer control to either position. From either position, the control will automatically return to the INT 2 or OFF position. MANUAL TILT STEERING COLUMN T o adjust the steering wheel: 1. Pull down the steering column tilt lever . 2. Move the steering wheel up or down until you find th[...]

ILLUMINATED VISOR MIRROR (IF EQUIPPED) Lift the mirror cover to turn on the visor mirror lamps. OVERHEAD CONSOLE (IF EQUIPPED) The appearance of your vehicle’ s overhead console will vary according to your option package. Storage compartment (if equipped) Press the OPEN control to open the storage compartment. The door will open slightly and can [...]

The tray and inside bin can be removed to open up space to fit a laptop computer , MP3 players, CDs or handbags. T o remove, open the console lid and pull the bin straight up and out from the console housing. The sliding tray and inside bin can be hooked on the side or rear of the console for extra storage. 2008 Tribute (j14) Owners Guide (post-200[...]

AUXILIARY POWER POINT (12VDC) W ARNING: Power outlets are designed for accessory plugs only . Do not insert any other object in the power outlet as this will damage the outlet and blow the fuse. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty . The [...]

POWER WINDOWS W ARNING: Do not leave children unattended in the vehicle and do not let children play with the power windows. They may seriously injure themselves. W ARNING: When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in the proximity of the window openings. Press and p[...]

Accessory delay W ith accessory delay , power windows and moonroof operate for up to ten minutes after the ignition switch is turned from the ACC or ON to the OFF position, the key is not in the ignition or until either front door is opened. W ARNING: Do not leave children unattended in the vehicle and do not let children play with the power window[...]

Fold-away mirrors Fold the side mirrors in carefully when driving through a narrow space, like an automatic car wash. Heated outside mirrors (if equipped) Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror gl[...]

Setting speed control The controls for using your speed control are located on the steering wheel for your convenience. 1. Press the ON control and release it. 2. Accelerate to the desired speed. 3. Press the SET + control and release it. 4. T ake your foot off the accelerator pedal. 5. The indicator light on the instrument cluster will turn on. No[...]

Resuming a set speed Press the RESUME control and release it. This will automatically return the vehicle to the previously set speed. Increasing speed while using speed control There are three ways to set a higher speed: • Press and hold the SET + control until you get to the desired speed, then release the control. • Press and release the SET [...]

• Depress the brake pedal or the clutch pedal (if equipped) until the desired vehicle speed is reached, press the SET + control. Turning of f speed control There are two ways to turn off the speed control: • Press the speed control OFF control. • T urn OFF the ignition. Note: When you turn off the speed control or the ignition, your speed con[...]

In Radio mode: • Press to access the next/previous preset station. In CD mode: • Press to listen to the next track on the disc. In any mode: • Press VOL + or - to adjust the volume. MOON ROOF (IF EQUIPPED) W ARNING: Do not let children play with the moon roof or leave children unattended in the vehicle. They may seriously hurt themselves. W A[...]

T o operate the moon roof: • The moon roof is equipped with an automatic, one-touch, express opening feature. Press and release the rear portion of the control. T o stop motion at any time during the one-touch opening, press the control again. • T o close, press and hold the front portion of the control. T o operate the moon roof vent position:[...]

Do not leave the liftgate or liftgate glass open while driving. Doing so could cause serious damage to the liftgate and its components as well as allowing carbon monoxide to enter the vehicle. W ARNING: Make sure that the liftgate door and/or window are closed to prevent exhaust fumes from being drawn into the vehicle. Exhaust fumes contain carbon [...]

W ARNING: Not securing luggage or cargo while driving is dangerous as it could move or be crushed during sudden braking or a collision and cause injury . Make sure luggage and cargo is secured before driving. Cargo management system (if equipped) The cargo management system consists of two storage compartments located in the floor of the rear cargo[...]

LUGGAGE RACK Y our vehicle is equipped with a roof rack. The maximum load for the roof rack is 100 lbs (44 kg), evenly distributed on the cross-bars. If it is not possible to evenly distribute the load, position it in the center or as far forward on the cross-bars as possible. Do not use the vehicle’ s door handles as tie down loops. Use the tie-[...]

T o remove the cross-bar assembly (if equipped) from the roof rack side rails: 1. Loosen the thumbwheel at both ends of the cross-bar (both cross-bars are adjustable). 2. Slide the cross-bar to the end of the rail. 3. Use a long, flat object to depress the tongue in the endcaps on both sides of the cross-bar . 4. Slide the cross-bar assembly off th[...]

T o reinstall the cross-bar assembly (if equipped) to the roof rack side rails: 1. Ensure that both cross-bar assemblies are installed with the F (front) arrow facing towards the front of the vehicle. 2. Use a long, flat object to depress the tongue in the endcaps on both sides of the cross-bar . 3. Slide the cross-bar assemblies over the end cap t[...]

KEYS Y our vehicle is equipped with two Integrated Keyhead T ransmitters (IKT s). The IKT functions as both a programmed ignition key that operates all the locks and starts the vehicle, and a remote keyless entry transmitter . Y our IKT s are programmed to your vehicle; using a non-programmed key will not permit your vehicle to start. If you lose y[...]

RECOMMENDED HANDLING OF THE INTEGRATED KEYHEAD T RANSMITTER (IKT) T o avoid inadvertently activating the remote entry functions of your vehicle, it is recommended that the Integrated Keyhead T ransmitter (IKT) be handled properly when starting and turning off your vehicle. When inserting the IKT into the ignition cylinder , place your thumb on the [...]

POWER DOOR LOCKS • Press the control to unlock all doors. • Press the control to lock all doors. Door key unlocking/locking Unlocking the doors T urn the key in the door cylinder to unlock the driver’ s door only . All other doors will remain locked. Locking the doors T urn the key in the door cylinder to lock the driver’ s door only . Smar[...]

REMOTE ENTRY SYSTEM (IF EQUIPPED) The Integrated Keyhead T ransmitter (IKT) complies with part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may c[...]

T wo step door unlocking 1. Press and release to unlock the driver’ s door . Note: The interior lamps will illuminate if the control on the overhead lamp is in the DOOR position. 2. Press and release again within three seconds to unlock the passenger doors, the liftgate and liftgate glass. One step door unlocking If the one step door unlocking fe[...]

Sounding a panic alarm Press and hold for 1.5 secondsto activate the alarm. T o deactivate the feature, press the control again, turn the ignition to the 3 (ON) or 4 (ST ART) position, or wait for the alarm to time out in approximately 3 minutes. Note: The panic alarm will only operate when the ignition is in the 1 (LOCK) position. Replacing the ba[...]

Replacing lost Integrated Keyhead T ransmitters (IKT s) If you would like to have your Integrated Keyhead T ransmitters reprogrammed because you lost one, or would like to buy additional IKT s, you can either reprogram them yourself, or take all IKT s to your authorized dealer for reprogramming. How to reprogram your Integrated Keyhead Transmitters[...]

Deactivating/activating perimeter lamps illuminated entry Y ou may enable/disable this feature by having your vehicle serviced by your authorized dealer . Y ou may also perform the following power door lock sequence to enable/disable the perimeter lamps feature. Note: Before starting, ensure the ignition is in the 1 (LOCK) position and all vehicle [...]

SECURILOCK 姟 PASSIVE ANTI-THEFT SYSTEM SecuriLock 娂 passive anti-theft system is an engine immobilization system. This system is designed to help prevent the engine from being started unless a coded Integrated Keyhead T ransmitter (IKT) programmed to your vehicle is used. The use of the wrong type of coded key may lead to a “no-start” condi[...]

Automatic arming The vehicle is armed immediately after switching the ignition to the 1 (LOCK) position. The theft indicator will flash every two seconds to act as a theft deterrent when the vehicle is armed. Automatic disarming The vehicle is disarmed immediately after the ignition is turned to the 3 (RUN) position. The theft indicator will illumi[...]

T ips: • Only use Integrated Keyhead T ransmitters (IKT s) or standard SecuriLock 娂 keys. • Y ou must have two previously programmed coded keys (keys that already operate your vehicle’ s engine) and the new unprogrammed key(s) readily accessible. • If two previously programmed coded keys are not available, you must take your vehicle to yo[...]

9. Remove the newly programmed coded key from the ignition. If the key has been successfully programmed it will start the vehicle’ s engine and will operate the remote entry system (if the new key is an Integrated Keyhead T ransmitter). The theft indicator light will illuminate for three seconds and then go out to indicate successful programming.[...]

SEA TING Adjustable head restraints The purpose of these head restraints is to help limit head motion in the event of a rear collision. T o properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible. The head restraints can be moved up and down. Push side co[...]

W ARNING: Not securing luggage or cargo while driving is dangerous as it could move or be crushed during sudden braking or a collision and cause injury . Make sure luggage and cargo are secured before driving. W ARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips and the shoulder belt snug across t[...]

Using the manual lumbar support (if equipped) The lumbar support control is located on the inboard side of the driver’ s seatback. T urn the lumbar support control clockwise to increase firmness. T urn the lumbar support control counterclockwise to increase softness. Adjusting the front power seat (if equipped) W ARNING: Never adjust the driver?[...]

W ARNING: T o reduce the risk of possible serious injury: Do not hang objects off seat back or stow objects in the seatback map pocket (if equipped) when a child is in the front passenger seat. Do not place objects underneath the front passenger seat or between the seat and the center console (if equipped). Check the “passenger airbag off” or ?[...]

Heated seats (if equipped) T o operate the heated seats: • Push the button located on the instrument panel to activate. • Push again to deactivate. The heated seats will activate when the ignition is in the RUN position and the engine is running. The system automatically shuts off after 10 minutes. REAR SEATS Head restraints (if equipped) The p[...]

Push control to lower head restraint. Folding down rear seats (60/40 split bench) 1. Raise the rear seat head restraint and remove. 2. Place the head restraint under the front seat for storage. 3. Pull the seat release control. NOTE: Make sure the floor is clear of all objects before folding the seat. 2008 Tribute (j14) Owners Guide (post-2002-fmt)[...]

4. Flip seat forward. Attach the seat belt web snap button to the quarter trim panel snap button. This will assure that seatbelt does not get caught by staying out of the seat back folding path. 5. T o release seatback, pull the seatback release lever (on top of seat) toward the front seat. NOTE: When the seatback release lever is pulled, slowly lo[...]

6. Rotate seatback down into load floor position. Returning the rear seats to upright position 1. Pull seatback up and into upright position making sure seatback locks into place. 2. Rotate seat cushion down into the seating position making sure that the seat cushion is locked into place and the RED seat unlatched indicator on release paddle is not[...]

W ARNING: Make sure seat belt buckle heads are through elastic holders on seat backs. Seat belt buckle heads may break if they are trapped underneath the seatback as the seatback is rotated down. W ARNING: Before returning the seatback to its original position, make sure that cargo or any objects are not trapped underneath the seatback. After retur[...]

T o install the rear cushion 1. Insert rod ends into floor mounting points and push the cushion to the inboard side of the vehicle. 2. Make sure that the hinges are locked into place. SAFETY RESTRAINTS Personal Safety System 姟 The Personal Safety System 娂 provides an improved overall level of frontal crash protection to front seat occupants and[...]

How does the Personal Safety System 姟 work? The Personal Safety System 娂 can adapt the deployment strategy of your vehicle’ s safety devices according to crash severity and occupant conditions. A collection of crash and occupant sensors provides information to the Restraints control module (RCM). During a crash, the RCM activates the seat bel[...]

Front passenger sensing system For airbags to do their job they must inflate with great force, and this force can pose a potentially deadly risk to occupants that are very close to the airbag when it begins to inflate. For some occupants, like infants in rear -facing child seats, this occurs because they are initially sitting very close to the airb[...]

Front seat belt pretensioners The seat belt pretensioners at the front outboard seating positions are designed to tighten the seat belts firmly against the occupant’ s body during frontal collisions, and in side collisions and rollovers when the vehicle is equipped with the side-curtain airbag system. This helps increase the effectiveness of the [...]

Safety restraints precautions W ARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips and the shoulder belt snug across the chest. W ARNING: T o reduce the risk of injury , make sure children sit where they can be properly restrained. W ARNING: Never let a passenger hold a child on his or her lap whi[...]

W ARNING: Placing a child, 12 years or younger , in the front seat is dangerous. The child could be hit by a deploying airbag and be seriously injured or even killed. A sleeping child is more likely to lean against the door and be hit by the side airbag (if equipped) in a moderate collision. Whenever possible, always secure a child, 12 years or you[...]

All seat belts in the vehicle are combination lap and shoulder belts. The passenger seat belts have two types of locking modes described below: V ehicle sensitive mode This is the normal retractor mode, which allows free shoulder belt length adjustment to your movements and locking in response to vehicle movement. For example, if the driver brakes [...]

• Grasp the shoulder portion and pull downward until the entire belt is pulled out. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the seat belt is now in the automatic locking mode. How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retract[...]

Seat belt height adjustment Y our vehicle has seat belt height adjustments at the front outboard seating positions. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder . T o adjust the shoulder belt height, squeeze and hold the buttons on the side and slide the height adjuster up or down. Release the buttons [...]

W ARNING: Failure to replace both front restraints under the above conditions could result in severe personal injuries in the event of a collision. The seat belt pretensioners will only function once. After they are deployed, they will not work again and must be replaced immediately , even if there was no front seat occupant seated at the time. W A[...]

Seat belt maintenance Inspect the seat belt systems periodically to make sure they work properly and are not damaged. NOTE: If unsure about the proper procedures, bring your vehicle to an authorized Mazda dealership for inspection. Inspect the seat belts to make sure there are no nicks, tears or cuts, replacing if necessary . Check all emergency lo[...]

Conditions of operation If... Then... The driver’ s seat belt is not buckled before the ignition switch is turned to the ON position... The seat belt warning light illuminates 1-2 minutes and the warning chime sounds 4-8 seconds. The driver’ s seat belt is buckled while the indicator light is illuminated and the warning chime is sounding... The[...]

If... Then... The driver’ s and front passenger’ s seat belts are buckled before the ignition switch is turned to the ON position or less than 1-2 minutes have elapsed since the ignition switch has been turned ON... The Belt-Minder 威 feature will not activate. The driver’ s or front passenger’ s seat belt is not buckled when the vehicle h[...]

Reasons given... Consider ... ⬙ Belts are uncomfortable ⬙ Seat belts are designed to enhance comfort. If you are uncomfortable - try different positions for the seat belt upper anchorage and seatback which should be as upright as possible; this can improve comfort. ⬙ I was in a hurry ⬙ Prime time for an accident. Seat Belt W arning Chime re[...]

W ARNING: Always wear the seat belt. Do not be tempted to sit on top of the belt to fool police or to defeat the warning system. The seat belt and seat belt warning system are there to protect your life. One time disable If at any time the driver/front passenger quickly buckles then unbuckles the seat belt for that seating position, the Belt-Minder[...]

1. T urn the ignition switch to the RUN (or ON) position. (DO NOT ST ART THE ENGINE) 2. W ait until the seat belt warning light turns off. (Approximately 1 minute) • Step 3 must be completed within 50 seconds after the seat belt warning light turns off. 3. For the seating position being disabled, buckle then unbuckle the seat belt 9 times, ending[...]

AIRBAG SUPPLEMENT AL RESTRAINT SYSTEM (SRS) Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the seat belt to help protect the driver and right front passenger from certain upper body injuries. W ARNING: Airbags DO NOT inflate slowly or gently and the risk of injury from a deployin[...]

W ARNING: The driver should always hold onto only the rim of the steering wheel. Never place your arm over the airbag module or anywhere inside the rim as a deploying airbag can result in serious arm fractures or other injuries. Steps you can take to properly position yourself away from the airbag: • Move your seat to the rear as far as you can w[...]

Children and airbags For additional important safety information, read all information on safety restraints in this guide. W ARNING: Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions rather than in the front seating position. Failure to follow thes[...]

The airbags inflate and deflate rapidly upon activation. After airbag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder or sodium compounds which may irritate the skin and eyes, but none of the residue is toxic. While the SRS is designed to help reduce serio[...]

• Side curtain airbag system. Refer to Side curtain airbag system later in this chapter . • Front passenger sensing system. Refer to Front passenger sensing system. later in this chapter . • “Passenger airbag off” or “pass airbag off” indicator lamp. Refer to Front passenger sensing system. later in this chapter . • Seat belt preten[...]

The front passenger sensing system uses a ⬙ passenger airbag off ⬙ or ⬙ pass airbag off ⬙ indicator which will illuminate and stay lit to remind you that the front passenger frontal airbag is disabled. The indicator lamp is located in the center stack of the instrument panel just above the air vents. Note : The indicator lamp will illuminat[...]

• If the indicator lamp remains lit even after this, the person should be advised to ride in the rear seat, and the system should be taken promptly to an authorized Mazda dealer for repair before that seat is occupied again. Occupant Pass Airbag Off Indicator Lamp Passenger Airbag Empty seat Unlit Disabled Small child in child safety seat or boos[...]

The front passenger sensing system may detect small or medium objects placed on the seat cushion. For most objects that are in the front passenger seat, the passenger airbag will be disabled. Even though the passenger airbag is disabled, the ⬙ pass airbag off ⬙ lamp may or may not be illuminated according to the table below . Objects Pass Airba[...]

W ARNING: T o reduce the risk of possible serious injury: Do not stow objects in seat back map pocket (if equipped) or hang objects off seat back if a child is in the front passenger seat. Do not place objects underneath the front passenger seat or between the seat and the center console (if equipped). Check Passenger Airbag Disable Indicator for p[...]

If it is necessary to modify an advanced front airbag system to accommodate a person with disabilities, contact the Mazda Customer Relationship Center at the phone number shown in the Customer Assistance section of this Owner’ s Manual . W ARNING: Any alteration/modification to the front passenger seat may affect the performance of the front pass[...]

W ARNING: Do not use accessory seat covers or non-Mazda leather seat upgrade kits. The use of accessory seat covers and kits may prevent the deployment of the side airbags and increase the risk of injury in an accident. W ARNING: Do not lean your head on the door . The side airbag could injure you as it deploys from the side of the seatback. W ARNI[...]

Side airbags, in combination with seat belts, can help reduce the risk of severe injuries in the event of a significant side impact collision. The side airbags are fitted on the outboard side of the seatbacks of the front seats. In certain lateral collisions, the airbag on the side affected by the collision will be inflated. If the front passenger [...]

Determining if the side airbags are operational First determine you have the optional side airbags - locate the “AIRBAG ⬙ labels on the outboard sides of the front seats. The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system. Refer to the Airbag readiness section in the Instrument cluster cha[...]

W ARNING: Do not lean your head on the door or window glass. The side-curtain airbags (if equipped) could injure you as it deploys from the headliner . W ARNING: Do not attempt to service, repair , or modify the side-curtain airbags (if equipped), fuses, the A, B, or C pillar trim, or the headliner on a vehicle containing side-curtain airbags. See [...]

How do the side-curtain airbags (if equipped) work? The design and development of the side air curtain system included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag T echnical W orking Group. These recommended testing procedures help reduce the risk of injuries related to the dep[...]

The side-curtain airbags are mounted to roof side-rail sheet metal, behind the headliner , above the first and second row seats. In certain lateral collisions or rollover events, the side-curtain airbags will be activated, regardless of which seats are occupied. In certain rollover events, the side-curtain airbag (if equipped) on both sides of the [...]

A difficulty with the system is indicated by one or more of the following: • The readiness light (same light as for front airbag system) will either flash or stay lit. • The readiness light will not illuminate immediately after ignition is turned on. • A series of five beep sounds will be heard. The tone pattern will repeat periodically until[...]

W ARNING: When possible, always place children under age 12 in the rear seat of your vehicle. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position. Children and seat belts If the child is the proper size, restrain the child in a safety seat. A child that outgro[...]

Booster seats position a child so that seat belts fit better . They lift the child up so that the lap belt rests low across the hips and the knees bend comfortably . Booster seats also make the shoulder belt fit better and more comfortably for growing children. When children should use booster seats Children need to use booster seats from the time [...]

• Those with a high back. If, with a backless booster seat, you cannot find a seating position that adequately supports your child’ s head, a high back booster seat would be a better choice. Both can be used in any vehicle in a seating position equipped with lap/shoulder belts if your child is over 40 lb. Children and booster seats vary widely [...]

W ARNING: Follow all instructions provided by the manufacturer of the booster seat. W ARNING: Never put the shoulder belt under a child’ s arm or behind the back because it eliminates the protection for the upper part of the body and may increase the risk of injury or death in a collision. W ARNING: Never use pillows, books, or towels to boost a [...]

• Put the seat belt in the automatic locking mode. Refer to Automatic locking mode . Mazda recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage. For more information on top tether straps, refer to Attaching child safety seats with [...]

2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the b[...]

5. T o put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode. 7. Pull the lap belt portion across the child seat toward the buck[...]

Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap which goes over the back of the seat and hooks to an anchoring point. T ether straps are available as an accessory for many older safety seats. Contact the manufacturer of your child seat for information about ordering a tether strap. T[...]

3. Locate the correct anchor for the selected seating position. NOTE: There are three tether anchors located on the headliner at the rear of the vehicle. W ARNING: If the tether strap is clipped incorrectly , the child safety seat may not be retained properly in the event of a collision. If the safety seat is not anchored properly , the risk of a c[...]

Attaching safety seats with LA TCH (Lower Anchors and T ethers for Children) attachments for child seat anchors Some child safety seats have two rigid or webbing mounted attachments that connect to two anchors at certain seating positions in your vehicle. When properly installed, this type of seat eliminates the need to use seat belts to attach the[...]

The lower anchors for child seat installation are located at the rear section of the rear seat between the cushion and seat back. Follow the child seat manufacturer’ s instructions to properly install a child seat with LA TCH attachments. W ARNING: Attach LA TCH lower attachments of the child seat only to the anchors shown. If you install a child[...]

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handle differently than passenger cars in the various driving conditions that are encountered on streets, highways and off-road. Utility vehicles and trucks are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to per[...]

Power is supplied to all four wheels through a transfer case or power transfer unit. 4WD vehicles allow you to select different drive modes as necessary . Information on transfer case operation and shifting procedures can be found in the Driving chapter . Information on transfer case maintenance can be found in the Maintenance and Specifications ch[...]

• Narrower — to provide greater maneuverability in tight spaces, particularly in off-road use. As a result of the above dimensional differences, SUV’ s and trucks often will have a higher center of gravity and a greater difference in center of gravity between the loaded and unloaded condition. These differences that make your vehicle so versa[...]

T readwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the ac[...]

TIRES T ires are designed to give many thousands of miles of service, but they must be maintained in order to get the maximum benefit from them. Glossary of tire terminology • T ire label: A label showing the OE (Original Equipment) tire sizes, recommended inflation pressure and the maximum weight the vehicle can carry . • T ire Identification [...]

INFLATING Y OUR TIRES Safe operation of your vehicle requires that your tires are properly inflated. Remember that a tire can lose up to half of its air pressure without appearing flat. Every day before you drive, check your tires. If one looks lower than the others, use a tire gauge to check pressure of all tires and adjust if required. At least o[...]

Maximum Permissible Inflation Pressure is the tire manufacturer’ s maximum permissible pressure and/or the pressure at which the maximum load can be carried by the tire. This pressure is normally higher than the manufacturer’ s recommended cold inflation pressure which can be found on the Safety Compliance Certification Label or T ire Label whi[...]

TIRE CARE Inspecting your tires Periodically inspect the tire treads for uneven or excessive wear and remove objects such as stones, nails or glass that may be wedged in the tread grooves. Check for holes or cuts that may permit air leakage from the tire and make necessary repairs. Also inspect the tire sidewalls for cracking, cuts, bruises and oth[...]

W ARNING: Age T ires degrade over time depending on many factors such as weather , storage conditions, and conditions of use (load, speed, inflation pressure, etc.) the tires experience throughout their lives. In general, tires should be replaced after six years regardless of tread wear . However , heat caused by hot climates or frequent high loadi[...]

W ARNING: Only use replacement tires and wheels that are the same size, load index, speed rating and type (such as P-metric versus L T -metric or all-season versus all-terrain) as those originally provided by Mazda. The recommended tire and wheel size may be found on either the Safety Compliance Certification Label or the T ire Label which is locat[...]

Important: Remember to replace the wheel valve stems when the road tires are replaced on your vehicle. It is recommended that the two front tires or two rear tires generally be replaced as a pair . The tire pressure sensors mounted in the wheels (originally installed on your vehicle) are not designed to be used in aftermarket wheels. The use of whe[...]

If you feel a sudden vibration or ride disturbance while driving, or you suspect your tire or vehicle has been damaged, immediately reduce your speed. Drive with caution until you can safely pull off the road. Stop and inspect the tires for damage. If a tire is under -inflated or damaged, deflate it, remove wheel and replace it with your spare tire[...]

• Front Wheel Drive (FWD) vehicles (front tires at top of diagram) • Rear Wheel Drive (RWD) vehicles/Four Wheel Drive (4WD)/All Wheel Drive (A WD) vehicles (front tires at top of diagram) Sometimes irregular tire wear can be corrected by rotating the tires. 2008 Tribute (j14) Owners Guide (post-2002-fmt) USA (fus) Tires, Wheels and Loading 137[...]

Note: If your tires show uneven wear ask a qualified technician at a Mazda dealership to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved before tire rotation. Note: Y our vehicle may be equipped with a dissimilar spare tire/wheel. A dissimilar spare tire/wheel is defined as a spare tire and/or wheel that [...]

4. R: Indicates a “radial” type tire. 5. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheel diameter . 6. 95: Indicates the tire’ s load index. It is an index that relates to how much weight a tire can carry . Y ou may find this information in your Owner[...]

8. U.S. DOT T ire Identification Number (TIN): This begins with the letters “DOT” and indicates that the tire meets all federal standards. The next two numbers or letters are the plant code designating where it was manufactured, the next two are the tire size code and the last four numbers represent the week and year the tire was built. For exa[...]

13. Maximum Permissible Inflation Pressure: Indicates the tire manufacturers’ maximum permissible pressure and/or the pressure at which the maximum load can be carried by the tire. This pressure is normally higher than the manufacturer’ s recommended cold inflation pressure which can be found on the Safety Compliance Certification Label or T ir[...]

Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example. 1. T: Indicates a type of tire, designated by the T ire and Rim A[...]

TIRE PRESSURE MONITORING SYSTEM (TPMS) Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard[...]

The T ire Pressure Monitoring System complies with part 15 of the FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. W ARNING: The[...]

When your temporary spare tire is installed When one of your road tires needs to be replaced with the temporary spare, the TPMS system will continue to identify an issue to remind you that the damaged road wheel/tire needs to be repaired and put back on your vehicle. T o restore the full functionality of the Tire Pressure Monitoring System, have th[...]

Low T ire Pressure W arning Light Possible cause Customer Action Required Solid W arning Light T ire(s) under -inflated 1. Check your tire pressure to ensure tires are properly inflated; refer to Inflating your tires in this chapter . 2. After inflating your tires to the manufacturer’ s recommended inflation pressure as shown on the T ire Label ([...]

Low T ire Pressure W arning Light Possible cause Customer Action Required Flashing W arning Light Spare tire in use Y our temporary spare tire is in use. Repair the damaged road wheel and re-mount it on the vehicle to restore system functionality . For a description of how the system functions under these conditions, refer to When your temporary sp[...]

If any tire is under -inflated, carefully drive the vehicle to the nearest location where air can be added to the tires. Inflate all the tires to the recommended inflation pressure. SNOW TIRES AND CHAINS NOTE: Snow tires must be the same size and grade as the tires you currently have on your vehicle. The tires on your vehicle have all-weather tread[...]

V ehicle Curb W eight – is the weight of your new vehicle when you picked it up from your authorized dealer plus any aftermarket equipment. Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be found on the T ire Label on the B-Pillar or the edge of the driver’ s doo[...]

Example only: Cargo W eight – includes all weight added to the Base Curb W eight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight. GA W (Gross Axle W eight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. 2008 T[...]

GA WR (Gross Axle W eight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’ s door . The total load on each axle must never exceed its GA WR. Note: For trailer towing information r[...]

GCW (Gross Combined W eight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer . GCWR (Gross Combined W eight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo and passengers – that the vehicle can handle without risking damage. (Important: The towing [...]

W ARNING: Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle and/or personal injury . Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on your vehicle’ s placard. 2. Determine the combined weight o[...]

• A final example for your vehicle with 1400 lb. (635 kg) of cargo and luggage capacity . Y ou and one of your friends decide to pick up cement from the local home improvement store to finish that patio you have been planning for the past 2 years. Measuring the inside of the vehicle with the rear seat folded down, you have room for 12-100 lb. (45[...]

Follow these guidelines to ensure safe towing procedure: • Be sure to locate all the warnings supplied by the trailer rental or sales company and study the unique requirements of each trailer you intend to tow . • Stay within your vehicle’ s load limits. • Thoroughly prepare your vehicle for towing. Refer to Preparing to tow in this chapter[...]

4x2 GCWR (Gross Combined W eight Rating)/T railer W eights Engine Maximum GCWR - lb. (kg) T railer W eight Range - lb. (kg) Maximum frontal area of trailer - ft 2 (m 2 ) 2.3L w/manual transmission 4900 (2223) 1500 (680) 24 (2.2) 2.3L w/automatic transmission 4980 (2259) 1500 (680) 24 (2.2) 3.0L w/automatic transmission 7040 (3193) 3500 (1588) 30 (2[...]

4x4 GCWR (Gross Combined W eight Rating)/T railer W eights Engine Maximum GCWR - lb. (kg) T railer W eight Range - lb. (kg) Maximum frontal area of trailer - ft 2 (m 2 ) 2.3L w/automatic transmission 5140 (2331) 1500 (680) 24 (2.2) 3.0L w/automatic transmission 7200 (3266) 3500 (1588) 30 (2.8) Notes: For high altitude operation, reduce GCW by 2% pe[...]

Hitches Do not use hitches that clamp onto the vehicle bumper . Use a load carrying hitch. Y ou must distribute the load in your trailer so that 10–15% of the total weight of the trailer is on the tongue. Safety chains Always connect the trailer’ s safety chains to the frame or hook retainers of the vehicle hitch. T o connect the trailer’ s s[...]

• T urn off the speed control. The speed control may shut off automatically when you are towing on long, steep grades. • Consult your local motor vehicle speed regulations for towing a trailer . • T o eliminate excessive shifting, use a lower gear . This will also assist in transmission cooling. (For additional information, refer to Understan[...]

Launching or retrieving a boat When backing down a ramp during boat launching or retrieval, • Do not allow the static water level to rise above the bottom edge of the rear bumper . • Do not allow waves to break higher than 6 inches (15 cm) above the bottom edge of the rear bumper . Exceeding these limits may allow water to enter critical vehicl[...]

STARTING Positions of the ignition 1. LOCK, locks the gearshift lever and steering column and allows key removal. 2. ACCESSORY , allows the electrical accessories such as the radio to operate while the engine is not running. 3. RUN, all electrical circuits operational and warning lights will illuminate. This is the position the key is in when you?[...]

W ARNING: If you smell exhaust fumes inside your vehicle, have your authorized dealer inspect your vehicle immediately . Do not drive if you smell exhaust fumes. Important safety precautions A computer system controls the engine’ s idle revolutions per minute (RPM). When the engine starts, the idle RPM runs higher than normal in order to warm the[...]

• Make sure the gearshift is in P (Park). If starting a vehicle with a manual transmission: • Make sure the parking brake is set. • Push the clutch pedal to the floor . 3. T urn the key to 3 (ON) without turning the key to 4 (ST ART). Some warning lights will briefly illuminate. See W arning lights and chimes in the Instrument Cluster chapter[...]

Starting the engine 1. T urn the key to 3 (RUN) without turning the key to 4 (ST ART). If there is difficulty in turning the key , rotate the steering wheel until the key turns freely . This condition may occur when: • the front wheels are turned • a front wheel is against the curb 2. T urn the key to 4 (ST ART), then release the key as soon as[...]

W ARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of Californi[...]

BRAKES Occasional brake noise is normal. If a metal-to-metal, continuous grinding or continuous squeal sound is present, the brake linings may be worn-out and should be inspected by an authorized dealer . If the vehicle has continuous vibration or shudder in the steering wheel while braking, the vehicle should be inspected by an authorized dealer .[...]

Using ABS When hard braking is required, apply continuous force on the brake pedal; do not pump the brake pedal since this will reduce the effectiveness of the ABS and will increase your vehicle’ s stopping distance. The ABS will be activated immediately , allowing you to retain steering control during hard braking and on slippery surfaces. Howev[...]

W ARNING: Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park) (automatic transmission) or in 1 (First) (manual transmission). NOTE: The parking brake is not recommended to stop a moving vehicle. However , if the normal brakes fail, the parking brake can be used to stop your vehicle in an emergency . S[...]

T raction Control T raction Control helps your vehicle maintain traction, when driving on slippery and/or hilly road surfaces, by detecting and controlling wheel spin. Excessive wheel spin is controlled by momentarily reducing engine power and/or applying the anti-lock brakes. T raction Control is a driver aid that helps your vehicle. If your vehic[...]

• Entering a snow-free road from a snow-covered side street, or vice versa. • Entering a paved road from a gravel road, or vice versa. • Driving on slick surfaces. • Cornering while towing a heavily loaded trailer (refer to T railer towing in the T ires, Wheels and Loading chapter .) Roll Stability Control 娂 (RSC) The RSC system works in [...]

If the vehicle is above 25 mph (40 km/h), momentarily pressing the ESC button will steadily illuminate the “sliding car” icon, however , the ESC system will remain enabled until the vehicle speed drops below 25 mph. If the vehicle speed decreases below 25 mph (40 km/h), the system will become deactivated, but if the vehicle speed subsequently i[...]

W ARNING: Aggressive driving in any road conditions can cause you to lose control of your vehicle increasing the risk of severe personal injury or property damage. The occurrence of a Electronic Stability Control (ESC) event is an indication that at least some of the tires have exceeded their ability to grip the road; this may lead to an increased [...]

PREPARING TO DRIVE W ARNING: Utility vehicles have a significantly higher rollover rate than other types of vehicles. W ARNING: In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Utility vehicles and trucks have larger tires and increased ground clearance, giving the vehicle a higher cente[...]

If the fuse is not blown, perform the following procedure: 1. Apply the parking brake, turn the ignition to LOCK, then remove the key . 2. Using a screwdriver or similar tool, carefully pry out the small Brake T ransmission Shift Interlock (BTSI) cover cap located to the right of the gearshift lever . 3. Insert a screwdriver or similar tool straigh[...]

Driving with an automatic overdrive transaxle Y our automatic overdrive transaxle provides fully automatic operation in either D (Overdrive) or with the O/D OFF switch depressed. Driving with the gearshift lever in D (Overdrive) gives the best fuel economy for normal driving conditions. For manual control, start in 1 (First) and then shift manually[...]

This vehicle is equipped with an adaptive T ransmission Shift Strategy . Adaptive Shift Strategy offers the optimal transmission operation and shift quality . When the vehicle’ s battery has been disconnected for any type of service or repair , the transmission will need to relearn the normal shift strategy parameters, much like having to reset y[...]

D (Overdrive) The normal driving position for the best fuel economy . T ransaxle operates in gears one through four . D (Overdrive) can be deactivated by pressing the O/D OFF switch on the side of the gearshift lever . This will illuminate the O/D OFF light and activate Drive. Drive (O/D OFF switch pressed) Drive is activated when the O/D OFF switc[...]

1 (First) • Provides maximum engine braking. • Allows upshifts by moving gearshift lever . • W ill not downshift into 1 (First) at high speeds; allows for 1 (First) when vehicle reaches slower speeds. W ARNING: When parking, do not use the gearshift in place of the parking brake. Always set the parking brake fully and make sure that the gears[...]

MANUAL TRANSMISSION OPERATION (IF EQUIPPED) Using the clutch The manual transaxle has a starter interlock that prevents cranking the engine unless the clutch pedal is fully depressed. T o start the vehicle: 1. Make sure the parking brake is fully set. 2. Press the clutch pedal to the floor , then put the gearshift lever in the neutral position. 3. [...]

Recommended shift speeds Upshift according to the following charts for best fuel economy: Upshifts during light to moderate accelerations and cruises (for best fuel economy) Shift from: 1-2 10 mph (16 km/h) 2-3 20 mph (32 km/h) 3-4 32 mph (52 km/h) 4-5 37 mph (60 km/h) Reverse Make sure that your vehicle is at a complete stop before you shift into [...]

FOUR WHEEL DRIVE (4WD) SYSTEM (IF EQUIPPED) W ARNING: For important information regarding safe operation of this type of vehicle, see Preparing to drive your vehicle in this chapter . Y our vehicle is equipped with an intelligent 4WD System that continuously monitors vehicle conditions and automatically adjusts the power distribution between the fr[...]

If your vehicle goes off the edge of the pavement • If your vehicle goes off the edge of the pavement, slow down, but avoid severe brake application, ease the vehicle back onto the pavement only after reducing your speed. Do not turn the steering wheel too sharply while returning to the road surface. • It may be safer to stay on the apron or sh[...]

W ARNING: Always set the parking brake fully and make sure the gearshift is latched in 1st gear or R (Reverse) (manual transaxles) or P (Park) (automatic transaxles). T urn the ignition to the LOCK position and remove the key whenever you leave your vehicle. W ARNING: If the parking brake is fully released, but the brake warning lamp remains illumi[...]

• If the vehicle goes from one type of surface to another (i.e., from concrete to gravel) there will be a change in the way the vehicle responds to a maneuver (steering, acceleration or braking). Again, avoid these abrupt inputs. Sand When driving over sand, try to keep all four wheels on the most solid area of the trail. A void reducing the tire[...]

Driving through deep water may damage the transmission. If the rear axle is submerged in water , the axle lubricant should be checked and changed, if necessary . The rear axle is filled with a lubricant that does not normally require a lubricant change for the life of the vehicle. Rear axle lubricant quantities should not need to be checked unless [...]

Descend a hill in the same gear you would use to climb up the hill to avoid excessive brake application and brake overheating. Do not descend in neutral; instead, disengage overdrive or manually shift to a lower gear . When descending a steep hill, avoid sudden hard braking as you could lose control. When you brake hard, the front wheels can’t tu[...]

• 4WD vehicles should be driven with traction devices as referred to in Using snow tires and traction devices in the T ires, Wheels and Loading chapter . Maintenance and Modifications The suspension and steering systems on your vehicle have been designed and tested to provide predictable performance whether loaded or empty and durable load carryi[...]

HAZARD FLASHER CONTROL The hazard flasher is located on the steering column, just behind the steering wheel. The hazard flashers will operate when the ignition is in any position or if the key is not in the ignition. Push in the flasher control and all front and rear direction signals will flash. Press the flasher control again to turn them off. Us[...]

FUEL PUMP SHUT-OFF SWITCH This device stops the electric fuel pump from sending fuel to the engine when your vehicle has had a substantial jolt. After an accident, if the engine cranks but does not start, this switch may have been activated. This switch is located in the front passenger’ s footwell, behind a flip-up cover , by the kick panel acce[...]

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A T an T an — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Y ellow Y ellow Y ellow Blu[...]

The fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 30A Not used (spare) 2 15A Brake On/Off switch 3 15A Not used (spare) 4 30A Not used (spare) 5 10A Brake Shift Interlock (BSI), SPDJB 6 20A T urn signals, Stop lamps 7 10A Low beam headlamps (left) 8 10A Low beam headlamps (right) 9 15[...]

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 16 15A Not used (spare) 17 20A All lock motor feeds, Liftgate release, Liftglass release 18 20A Heated seat 19 25A Rear wiper 20 15A Datalink 21 15A Fog lamps 22 15A Park lamps 23 15A High beam headlamps 24 20A Horn relay 25 10A Demand lamps 26 10A Instrument panel clu[...]

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 44 10A Not used (spare) 45 5A Front wiper logic, Blower motor relay 46 7.5A OCS (restraints), P ADI (restraints) 47 30A Circuit Breaker Power windows, Moon roof 48 — Delayed accessory relay Power distribution box The power distribution box is located in the engine co[...]

The high-current fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description A 80A Midi EP AS B 125A Midi SPDJB 1 15A* Heated mirror 2 30A** Rear defroster 3 20A** Rear power point (center console) 4 20A** Fuel pump 5 10A* Powertrain Control Module (PCM) Keep Alive power 6 15A* Alternator 7 10A* Reverse lamps [...]

Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 19 30A** Power seats 20 — A/C clutch relay 21A — Rear defroster relay 21B — Not used 21C — Blower relay 21D — PCM relay 22 — Not used 23 — Not used 24 10A* PCM transmission 25 — Not used 26 10A* PCM mil 27 10A* PCM non-mil 28 15A* PCM 29 15A* Ignition coils 30A ?[...]

CHANGING A FLAT TIRE If you get a flat tire while driving: • do not brake heavily . • gradually decrease the vehicle’ s speed. • hold the steering wheel firmly . • slowly move to a safe place on the side of the road. Y our vehicle may be equipped with a conventional spare tire that is different in one or more of the following: type, brand[...]

If you have a dissimilar spare tire/wheel, then it is intended for temporary use only . This means that if you need to use it, you should replace it as soon as possible with a road tire/wheel that is the same size and type as the road tires and wheels that were originally provided by Mazda. If the dissimilar spare tire or wheel is damaged, it shoul[...]

3. Full-size dissimilar spare without label on wheel When driving with the full-size dissimilar spare tire/wheel, do not: • Exceed 70 mph (113 km/h) • Use more than one dissimilar spare tire/wheel at a time • Use commercial car washing equipment • Use snow chains on the end of the vehicle with the dissimilar spare tire/wheel The usage of a [...]

Stopping and securing the vehicle 1. Park on a level surface, set the parking brake and activate hazard flashers. 2. Place gearshift lever in P (Park) (automatic transmission) or R (Reverse) (manual transmission) and turn engine off. Removing the jack and tools The jack and tools are located under the carpeted load floor . Pull back the carpet away[...]

Removing the spare tire or spare tire and tether (if equipped) 1. Insert the lug wrench through the access hole in the rear bumper . 2. T urn the handle counterclockwise and lower the spare tire until it can be slid rearward and the cable is slack. 3. Slide the retainer through the center of the wheel. If equipped with a tether , perform the follow[...]

6. If not replacing the spare or flat tire to the underbody storage area, raise winch up into the installed position. 7. Use the attached fastener strap (2) to tie the tether end to the winch actuator shaft (if equipped). Tire change procedure W ARNING: When one of the front wheels is off the ground, the transmission alone will not prevent the vehi[...]

1. Block the diagonally opposite wheel. 2. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. Before placing the jack under the vehicle, NOTE the jack locations: • Front View shown from rear of front tire. Position the jack directly below the protruding bolt. 2008 Tribute (j14[...]

• Rear View shown from forward of rear tire. Position the jack directly below the stud on the rear trailing arm. 3. Position the jack according to the guides and turn the jack handle clockwise until the tire is a maximum of 1 inch (25 mm) off the ground. Never use the differentials as a jacking point. 2008 Tribute (j14) Owners Guide (post-2002-fm[...]

W ARNING: T o lessen the risk of personal injury , do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire. 4. Remove the lug nuts with the lug nut wrench. 5. Replace the flat tire with the spare tire, making sure the valve stem [...]

If you are stowing a tire that requires reattaching it to the vehicle with a tether , perform these steps first, then proceed with the steps following. 1. Place tire on end with valve stem facing rearward, away from vehicle. 2. Place tether into bolt holes in wheel and attach lug nut using lug wrench. 3. Lay the tire on the ground with the valve st[...]

7. Repeat this tightness check procedure when servicing the spare tire pressure (every six months), or at any time that the spare tire is disturbed through service of other components. WHEEL LUG NUT TORQUE SPECIFICATIONS Retighten the lug nuts to the specified torque at 500 miles (800 km) after any wheel disturbance (tire rotation, changing a flat [...]

4. Check whether coolant or steam is escaping from under the hood or from the engine compartment. • If steam is coming from the engine compartment: do not go near the front of the vehicle. Stop the engine, then turn the ignition switch to the ON position without starting the engine. The radiator cooling fans will start to cool the engine. • If [...]

Preparing your vehicle When the battery is disconnected or a new battery is installed, the automatic transmission must relearn its shift strategy . As a result, the transmission may have firm and/or soft shifts. This operation is considered normal and will not affect function or durability of the transmission. Over time, the adaptive learning proce[...]

2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery . 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery . + – + – + – + – 2008 Tribute (j14) Owners Guide (post-2002-fmt) USA (fus) Roadside Emergencies 209[...]

4. Make the final connection of the negative (-) cable to an exposed metal part of the disabled vehicle’ s engine, away from the battery and the fuel injection system. NOTE: Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. W ARNING: Do not connect the end of the second cable to the negative (-) terminal of t[...]

Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery . 2. Remove the jumper cable on the negative (-) connection of the booster vehicle’ s batter[...]

3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery . After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle c[...]

WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member of a roadside assistance program, your roadside assistance service provider . It is recommended that your vehicle be towed with a wheel lift and dollies or flatbed equipment. Do not tow with a slingbelt. Mazda has not approved a sli[...]

If the vehicle is towed by other means or incorrectly , vehicle damage may occur . In case of a roadside emergency with a disabled vehicle (without access to wheel dollies, car hauling trailer or flatbed transport vehicle) your vehicle (regardless of powertrain configuration) can be flat towed (all wheels on the ground) under the following conditio[...]

CUSTOMER ASSISTANCE (U.S.A. MAINLAND AND HAWAII) Y our complete and permanent satisfaction is our business. W e are here to serve you. All Authorized Mazda Dealers have the knowledge and the tools to keep your Mazda vehicle in top condition. If you have any questions or recommendations for improvement regarding the service of your Mazda vehicle or [...]

Whatever way you contact us, please help us to serve you more efficiently and effectively by providing the following information: 1. Y our name, address, and telephone number 2. Y ear and model of vehicle 3. V ehicle Identification Number (17 digits, noted on your registration or title or located on the upper driver’ s side corner of the dash) 4.[...]

2. Y ear and model of vehicle 3. V ehicle Identification Number (VIN). Refer to V ehicle identification label in the Maintenance and Specifications chapter of this manual for the location of the VIN. 4. Purchase date. 5. Present odometer reading. 6. Y our authorized dealer’ s name and location 7. The nature of your problem and/or cause of dissati[...]

However , before you can proceed with CAMV AP you must follow your Mazda dispute resolution process as outlined previously . CAMV AP is fully implemented in all provinces and territories. Consumers wishing to obtain further information about the Program can obtain an information booklet from their authorized dealer , the Provincial Administrator at[...]

CUSTOMER ASSISTANCE (PUERTO RICO & VIRGIN ISLANDS) Y our complete and permanent satisfaction is our business. That is why all Authorized Mazda Dealers have the knowledge and the tools to keep your Mazda vehicle in top condition. If you have any questions or recommendations for improvement regarding the service of your Mazda vehicle or servicing[...]

IN CALIFORNIA (U.S. ONLY) California Civil Code Section 1793.2(d) requires that, if a manufacturer or its representative is unable to repair a motor vehicle to conform to the vehicle’ s applicable express warranty after a reasonable number of attempts, the manufacturer shall be required to either replace the vehicle with one substantially identic[...]

CANADA Mazda Canada, Inc. 55 V ogell Road Richmond Hill, Ontario L4B 3K5 Canada TEL: 1 (800) 263–4680 (in Canada) (416) 609–9909 (outside Canada) PUERTO RICO & VIRGIN ISLANDS Plaza Motors Corp. (Mazda de Puerto Rico) P .O. Box 362722, San Juan, Puerto Rico 00936–2722 TEL: (787) 788–9300 GUAM (d.b.a. T riple J. Enterprises, Inc.) P .O. B[...]

• California Emission Control W arranty (if applicable) • Replacement Parts and Accessories Limited W arranty • T ire W arranty NOTE: Detailed warranty information is provided with your Mazda portfolio. Outside the United States Government regulations in the United States require that automobiles meet specific emission regulations and safety [...]

vehicles built for use in Canada could be eligible for exportation to the United States with specific vehicle modifications to comply with the United States Federal Motor V ehicle Safety requirements. Special Note: The above is applicable for permanent import/export situations and not related to travelers on vacation. Y ou may have the following pr[...]

W ARNING: Add-On Electrical and Electronic Equipment: Incorrectly choosing or installing improper add-on equipment or choosing an improper installer could be dangerous. Essential systems could be damaged, causing engine stalling, air -bag (SRS) activation, ABS inactivation, or a fire in the vehicle. Be very careful in choosing and installing add-on[...]

REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway T raffic Safety Administration (NHTSA) in addition to notifying Mazda Corporation. If NHTSA receives similar complaints, it may open an investigation, and if [...]

W ASHING THE EXTERIOR W ash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo. • Never use strong household detergents or soap, such as dish washing or laundry liquid. These products can discolor and spot painted surfaces. • Never wash a vehicle that is “hot to the touch” or during exposure to strong, direct sunlig[...]

PAINT CHIPS Y our dealer has touch-up paint to match your vehicle’ s color . T ouch-up paint can be used to repair minor scratches to painted surfaces. • Remove particles such as bird droppings, tree sap, insect deposits, tar spots, road salt and industrial fallout before repairing paint chips. • Always read the instructions before using the [...]

• 2.3L DOHC I4 Engine • 3.0L DOHC V6 Engine • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your dealer . • For routine cleaning, use cool or lukewarm water wi[...]

WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should be cleaned regularly . If the wipers do not wipe properly , substances on the vehicle’ s glass or the wiper blades may be the cause. These may include hot wax treatments used by commercial car washes, water repellant coatings, tree sap, or other organic con[...]

INTERIOR For fabric, carpets, cloth seats, seat belts and seats equipped with side air bags (if equipped): • Remove dust and loose dirt with a vacuum cleaner . • Remove light stains and soil with Upholstery Cleaner and Spot Remover (0000–77–430E-01), available at your authorized Mazda dealer . • If grease or tar is present on the material[...]

MAZDA CAR CARE PRODUCTS Y our Mazda dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle. Each product is made from high quality materials th[...]

INTRODUCTION Be extremely careful to prevent injury to yourself and others or damage to your vehicle when using this manual for inspection and maintenance. If you’re unsure about any procedure it describes, we strongly urge you to have a reliable and qualified service shop perform the work, preferably an authorized Mazda Dealer . Factory-trained [...]

NOTE: After the described period, continue to follow the described maintenance at the recommended intervals. SCHEDULE 1 I : Inspect and repair , clean, adjust, or replace if necessary (Oil-permeated air filter cannot be cleaned using the air -blow method) R : Replace L : Lubricate Maintenance Item Maintenance Interval (Number of months or km (miles[...]

Maintenance Item Maintenance Interval (Number of months or km (miles), whichever comes first) Months 6 12 18 24 30 36 42 48 54 60 66 72 x 1000 Miles 7.5 15 22.5 30 37.5 45 52.5 60 67.6 75 82.5 90 (x 1000 Km) (12) (24) (36) (48) (60) (72) (84) (96) (108) (120) (132) (144) CHASSIS and BODY Brake lines, hoses and connections I I I Disc brakes IIIIII D[...]

SCHEDULE 2 I : Inspect and repair , clean, adjust, or replace if necessary (Oil-permeated air filter cannot be cleaned using the air -blow method) R : Replace L : Lubricate Maintenance Item Maintenance Interval (Number of months or km (miles), whichever comes first) Months 4 8 12 16 20 24 28 32 36 40 44 48 x 1000 miles 5 10 15 20 25 30 35 40 45 50 [...]

Maintenance Item Maintenance Interval (Number of months or km (miles), whichever comes first) Months 4 8 12 16 20 24 28 32 36 40 44 48 x 1000 miles 5 10 15 20 25 30 35 40 45 50 55 60 (x 1000 Km) (8) (16) (24) (32) (40) (48) (56) (64) (72) (80) (88) (96) ELECTRICAL SYSTEM Function of all lights I I I IIIIIIIII CHASSIS and BODY Brake lines, hoses and[...]

*2 If the vehicle is operated under any of the following conditions, change the spark plugs every 60,000 miles (96,000 km) or shorter . a) Repeated short-distance driving. b) Extended periods of idling or low-speed operation. c) Driving for long periods in cold temperatures or extremely humid climates. *3 If this component has been submerged in wat[...]

SERVICE RECOMMENDATIONS T o help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy . If your vehicle requires professional service, your authorized dealer can provide necessary parts and service. Check your “W arranty Information” to find out which parts and services are covered. Us[...]

Working with the engine on • Automatic transmission: 1. Set the parking brake and shift to P (Park). 2. Block the wheels. • Manual transmission: 1. Set the parking brake, depress the clutch and place the gearshift in N (Neutral). 2. Block the wheels. W ARNING: T o reduce the risk of vehicle damage and/or personal burn injuries do not start your[...]

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.3L I4 engine 1. Engine coolant reservoir 2. Engine oil filler cap 3. Automatic transmission dipstick (if equipped) 4. Brake/Clutch fluid reservoir 5. Air filter assembly 6. Power distribution box 7. Battery 8. Engine coolant bleed valve 9. Engine oil dipstick 10. W indshield washer fluid reservoir [...]

3.0L DOHC V6 engine 1. Engine coolant reservoir 2. Automatic transmission fluid dipstick 3. Brake fluid reservoir 4. Air filter assembly 5. Power distribution box 6. Battery 7. Engine oil dipstick 8. Engine oil filler cap 9. W indshield washer fluid reservoir 2008 Tribute (j14) Owners Guide (post-2002-fmt) USA (fus) Maintenance and Specifications 2[...]

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low . In very cold weather , do not fill the reservoir completely . Only use a washer fluid that meets Mazda specifications. Do not use any special washer fluid such as windshield water repellent type fluid or bug wash. They may cause squeaking, chatter noise, streaking and sme[...]

CHANGING THE WIPER BLADES 1. Pull the wiper blade and arm away from the glass. T urn the blade at a right angle to the arm. 2. Squeeze the locking tabs to release the blade from the arm and pull the blade away from the arm to remove it. 3. Attach the new blade to the arm and snap it into place. Replace wiper blades at least once per year for optimu[...]

Changing rear window wiper blade The rear wiper arm is designed without a service position. This reduces the risk of damage to the blade in an automatic car wash. T o replace the wiper blade: 1. Grab the wiper arm just below the blade attachment and pull it as far away from the glass as possible. Do not use excessive force because it can break the [...]

• 2.3L I4 engine • 3.0L DOHC V6 Duratec engine 6. W ipe the indicator clean. Insert the indicator fully , then remove it again. • If the oil level is within the MIN and MAX marks or the lower and upper holes, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below the MIN mark or the lower hole, engine oil must be added to [...]

• 3.0L DOHC V6 Duratec engine • If required, add engine oil to the engine. Refer to Adding engine oil in this chapter . • Do not overfill the engine with oil. Oil levels above the MAX mark or upper hole may cause engine damage. If the engine is overfilled, some oil must be removed from the engine by an authorized dealer . 7. Put the indicator[...]

Engine oil and filter recommendations SAE 5W -20 engine oil is recommended Look for this certification trademark. Use SAE 5W -20 motor oil certified for gasoline engines by the American Petroleum Institute (API). An oil with this trademark symbol conforms to the current engine and emission system protection standards and fuel economy requirements o[...]

BATTERY Y our vehicle is equipped with a Mazda maintenance-free battery which normally does not require additional water during its life of service. If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced. For longer , trouble-free operation, keep the top of the battery clean and dry . Also, ma[...]

W ARNING: Keep batteries out of reach of children. Batteries contain sulfuric acid. A void contact with skin, eyes or clothing. Shield your eyes when working near the battery to protect against possible splashing of acid solution. In case of acid contact with skin or eyes, flush immediately with water for a minimum of 15 minutes and get prompt medi[...]

• Always dispose of automotive batteries in a responsible manner . Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries. ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant should be checked at the intervals listed in[...]

When the engine is cold, check the level of the engine coolant in the reservoir . • The engine coolant should be at the“FULL COLD” level or within the “COLD FILL RANGE” as listed on the engine coolant reservoir (depending upon application). • Refer to scheduled maintenance section for service interval schedules. • Be sure to read and [...]

• DO NOT MIX recycled coolant and conventional coolant together in your vehicle. Mixing of engine coolants may harm your engine’ s cooling system. • The use of an improper coolant may harm engine and cooling system components and may void the warranty of your vehicle’ s engine cooling system. If you are unsure which type of coolant your veh[...]

W ARNING: T o reduce the risk of personal injury , make sure the engine is cool before unscrewing the coolant pressure relief cap. The cooling system is under pressure; steam and hot liquid can come out forcefully when the cap is loosened slightly . 1. Before you begin, turn the engine off and let it cool. 2. When the engine is cool, wrap a thick c[...]

If necessary , add enough 50/50 concentration of engine coolant and distilled water to bring the liquid level to the proper level. If you have to add more than 1.0 quart (1.0 liter) of engine coolant per month, have your authorized dealer check the engine cooling system. Y our cooling system may have a leak. Operating an engine with a low level of [...]

• NEVER decrease the coolant concentration below 40%. • Decreased engine coolant concentrations below 40% will decrease the corrosion protection characteristics of the engine coolant and may cause engine damage. • Decreased engine coolant concentrations below 40% will decrease the freeze protection characteristics of the engine coolant and ma[...]

When fail-safe mode is activated Y ou have limited engine power when in the fail-safe mode, so drive the vehicle with caution. The vehicle will not be able to maintain high-speed operation and the engine will run rough. Remember that the engine is capable of completely shutting down automatically to prevent engine damage, therefore: 1. Pull off the[...]

W ARNING: If you do not use the proper fuel filler cap, excessive vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision, which may result in possible personal injury . W ARNING: Automotive fuels can cause serious injury or death if misused or mishandled. W ARNING: Gasoline may contain benzene, which is[...]

• Fuels can also be harmful if absorbed through the skin. If fuel is splashed on the skin and/or clothing, promptly remove contaminated clothing and wash skin thoroughly with soap and water . Repeated or prolonged skin contact with fuel liquid or vapor causes skin irritation. • Be particularly careful if you are taking “Antabuse” or other f[...]

Fuel Filler Cap Y our fuel tank filler cap has an indexed design with a 1/4 turn on/off feature. When fueling your vehicle: 1. T urn the engine/ignition switch to the off position. 2. Carefully turn the filler cap counterclockwise until it spins off. 3. T o install the cap, align the lugs on the cap with the threads on the filler pipe. 4. T urn the[...]

Repairs to correct the effects of using a fuel for which your vehicle was not designed may not be covered by your warranty . Octane recommendations Y our vehicle is designed to use “Regular” unleaded gasoline with pump (R+M)/2 octane rating of 87. W e do not recommend the use of gasolines labeled as “Regular” that are sold with octane ratin[...]

Running out of fuel A void running out of fuel because this situation may have an adverse effect on powertrain components. If you have run out of fuel: • Y ou may need to cycle the ignition from OFF to ON several times after refueling to allow the fuel system to pump the fuel from the tank to the engine. On restarting, cranking time will take a f[...]

For consistent results when filling the fuel tank: • T urn the engine/ignition switch to the off position prior to refueling, an error in the reading will result if the engine is left running. • Use the same filling rate setting (low — medium — high) each time the tank is filled. • Allow no more than two automatic click-offs when filling.[...]

Habits • Smooth, moderate operation can yield up to 10% savings in fuel. • Steady speeds without stopping will usually give the best fuel economy . • Idling for long periods of time (greater than one minute) may waste fuel. • Anticipate stopping; slowing down may eliminate the need to stop. • Sudden or hard accelerations may reduce fuel e[...]

• Adding certain accessories to your vehicle (for example bug deflectors, rollbars/light bars, running boards, ski/luggage racks) may reduce fuel economy . • Using fuel blended with alcohol may lower fuel economy . • Fuel economy may decrease with lower temperatures during the first 8–10 miles (12–16 km) of driving. • Driving on flat te[...]

W ARNING: Do not park, idle, or drive your vehicle in dry grass or other dry ground cover . The emission system heats up the engine compartment and exhaust system, which can start a fire. Illumination of the indicator , charging system warning light or the temperature warning light, fluid leaks, strange odors, smoke or loss of engine power , could [...]

4. Driving through deep water—the electrical system may be wet. These temporary malfunctions can be corrected by filling the fuel tank with good quality fuel, properly tightening the fuel cap or letting the electrical system dry out. After three driving cycles without these or any other temporary malfunctions present, the indicator should stay of[...]

15 minutes of steady driving on an expressway/highway followed by 20 minutes of stop-and-go driving with at least four 30-second idle periods. Allow the vehicle to sit for at least eight hours without starting the engine. Then, start the engine and complete the above driving cycle. The engine must warm up to its normal operating temperature. Once s[...]

2. Park the vehicle on a level surface and engage the parking brake. 3. W ith the parking brake engaged and your foot on the brake pedal, start the engine and move the gearshift lever through all of the gear ranges. Allow sufficient time for each gear to engage. 4. Latch the gearshift lever in P (Park) and leave the engine running. 5. Remove the di[...]

Adjusting automatic transmission fluid levels Before adding any fluid, make sure the correct type is used. The type of fluid used is normally indicated on the dipstick and also in the Maintenance product specifications and capacities section in this chapter . Use of a non-approved automatic transmission fluid may cause internal transaxle component [...]

When changing the air filter element, only use a genuine Mazda air filter element. W ARNING: T o reduce the risk of vehicle damage and/or personal burn injuries do not start your engine with the air cleaner removed and do not remove it while the engine is running. 1. Loosen the clamp that secures the air inlet tube to the engine air filter cover an[...]

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIES Item Application Mazda part name or equivalent Capacity Brake fluid and (clutch fluid–if equipped) All High Performance DOT 3 Motor V ehicle Brake Fluid Between MIN and MAX on reservoir Engine coolant 2.3L I4 engine with manual transaxle Mazda yellow-colored Premium Engine Coolant 1 5.3 quarts (5.[...]

Item Application Mazda part name or equivalent Capacity Manual transaxle fluid Manual transaxle (2WD) API service GL-4 SAE 75W -90 2.4 quarts (2.3L) 2 Manual transaxle (4WD) 2.5 quarts (2.4L) 2 Automatic transaxle fluid Automatic transaxle MERCON 威 VA T F 3 10.2 quarts (9.6L) 4 Rear axle fluid 4WD SAE 80W -90 Axle Lubricant 2.4 pints (1.15L) 5 W [...]

ENGINE SPECIFICA TIONS Engine 2.3L I4 engine 3.0L DOHC V6 engine Cubic inches 140 183 Required fuel 87 octane 87 octane Firing order 1-3-4-2 1-4-2-5-3-6 Ignition system Coil on plug Coil on plug Spark plug gap 0.049–0.053 inch (1.25–1.35mm) 0.052–0.056 inch (1.32–1.42mm) Compression ratio 9.7:1 10.0:1 Engine drivebelt routing • 2.3L I4 En[...]

IDENTIFYING YOUR VEHICLE Safety Compliance Certification Label The National Highway T raffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located. The Safety Compliance Certification Label is located on the structur[...]

The V ehicle Identification Number (VIN) contains the following information: 1. W orld manufacturer identifier 2. Brake system / Gross V ehicle W eight Rating (GVWR) / Restraint System 3. V ehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence number T RANSMISSION/T RANSAXLE CODE DESIGNA[...]

CELL PHONES Use of cell phones and other devices by driver: W ARNING: Use of any electrical devices such as cell phones, computers, portable radios, vehicle navigation or other devices by the driver while the vehicle is moving is dangerous. Dialing a number on a cell phone while driving also ties-up the driver’ s hands. Use of these devices will [...]

A ABS (see Brakes) ..................... 166 Accessory delay .......................... 48 Air cleaner filter ............... 269, 271 Air conditioning manual heating and air conditioning system ............ 29 Airbag supplemental restraint system ..........97, 106, 109 and child safety seats ..............99 description ................97, 106, 10[...]

Child safety seats - booster seats ........................................... 114 Cleaning your vehicle engine compartment .............. 227 instrument panel ....................229 interior ..................................... 230 Mazda car care products .......231 plastic parts ............................ 228 washing .........................[...]

Foglamps ..................................... 32 Four -Wheel Drive vehicles driving off road ....................... 181 preparing to drive your vehicle ..................................... 173 Fuel ............................................ 256 calculating fuel economy .......261 cap ........................................... 259 capacity ...[...]

fog lamps ................................... 32 headlamps ................................. 32 headlamps, flash to pass ..........33 instrument panel, dimming ..... 33 interior lamps .....................35–37 replacing bulbs ......................... 38 Lane change indicator (see T urn signal) ........................ 35 Liftgate ..............[...]

Safety restraints .............. 81, 85–89 Belt-Minder 威 ............................. 92 extension assembly ..................90 for adults ............................. 86–88 for children .....................113–114 Occupant Classification Sensor ........................................ 83 seat belt maintenance .............. 91 warning [...]

V V ehicle Identification Number (VIN) .......................................... 274 V ehicle loading ..........................148 V entilating your vehicle ........... 165 W W arning lights (see Lights) ....... 12 W asher fluid ..............................242 W ater , Driving through ............. 187 W indows power ...........................[...]

283[...]

284[...]

285[...]

286[...]

287[...]

288[...]