Mercury 1999 Villager manual

Before driving Introduction 2 Instrumentation 3 Controls and features 19 Seating and safety restraints 110 Starting and driving Starting 152 Driving 157 Roadside emergencies 171 Servicing Maintenance and care 191 Capacities and specifications 235 Customer assistance 241 Reporting safety defects 254 Index 255 All rights reserved. Reproduction by any[...]

ICONS Indicates a safety alert. Read the following section on W arnings. Indicates vehicle information related to recycling and other environmental concerns will follow . Correct vehicle usage and the authorized disposal of waste cleaning and lubrication materials are significant steps towards protecting the environment. Indicates a message regardi[...]

Instrumentation 3[...]

OFF AUTO 1 AUTO 2 PUSH INTERIOR C E F H 1/2 FUEL TEMP N O R M A L 0 0 0 0 20 30 40 50 60 70 80 90 40 60 80 100 120 140 0 2 3 4 5 6 7 1 CRUISE OFF CANCEL RES ACCEL COAST SET VOL NEXT VOL DIM Panel dimmer (pg. 19) Headlamp control (pg. 19) Speed control (pg. 85) Driver side air bag (pg. 131) T urn signal and wiper/washer control (pg. 86) Instrument c[...]

OFF REAR 1 2 3 4 1 MAX A/C A/C OFF 2 3 4 OVERDRIVE OFF/ON FF REW SIDE 1 - 2 BASS TREB BAL FADE TAPE AMS AM FM CD CLK VOL - PUSH ON SHUFFLE COMP CD EJ CD SCAN DISCS TUNE SEEK 3 2 14 5 6 DC 12V SECURITY HAZARD RR DEFOG RR WIPER RR WASH Gearshift (including overdrive button) (pg. 161) Hazard flasher (pg. 171) Rear wiper/washer (pg. 87) Rear defroster [...]

W ARNING LIGHTS AND CHIMES Standard analog instrument cluster Optional electronic instrument cluster Charging system Illuminates when the ignition is turned to the ON position and the engine is off. The light also illuminates when the battery is not charging properly , requiring electrical system service. Air bag readiness Momentarily illuminates w[...]

Safety belt Momentarily illuminates when the ignition is turned to the ON position to remind you to fasten your safety belts. For more information, refer to the Seating and safety restraints chapter . Brake system warning Momentarily illuminates when the ignition is turned to the ON position. Also illuminates if the parking brake is engaged. If the[...]

T urn signal Illuminates when the left or right turn signal or the hazard lights are turned on. If one or both of the indicators stay on continuously or flash faster , check for a burned-out turn signal bulb. Refer to Exterior bulbs in the Maintenance and care chapter . Speed control This light comes on when either the COAST/SET or RES/ACCEL contro[...]

Service engine soon Y our vehicle is equipped with a computer that monitors the engine’ s emission control system. This system is commonly known as the On Board Diagnostics System (OBD II). The OBD II system protects the environment by ensuring that your vehicle continues to meet government emission standards. The OBD II system also assists the s[...]

Light is blinking: Engine misfire is occurring which could damage your catalytic converter . Y ou should drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced at the first available opportunity . Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter , th[...]

Headlamps on warning chime Sounds when the headlamps or parking lamps are on, the ignition is off (and the key is not in the ignition) and the driver’ s door is opened. GAUGES Standard analog instrument cluster gauges Optional electronic instrument cluster gauges T achometer Indicates the engine speed in revolutions per minute. Driving with your [...]

• Standard analog instrument cluster • Optional electronic instrument cluster Speedometer Indicates the current vehicle speed. • Standard analog instrument cluster • Optional electronic instrument cluster 0 2 3 4 5 6 7 8 RPMx1000 1 CRUISE MPH km/h km 0 1 2 3 4 5 6 78 X 1000 RPM TRIP 1 TRIP 2 0 MPH km/h 10 20 30 40 50 60 70 80 90 100 20 40 6[...]

Odometer Registers the total kilometers (miles) of the vehicle. • Standard analog instrument cluster • Optional electronic instrument cluster Refer to Electronic Message Center for information on how to switch the display from metric to English measurements. T rip odometer Registers the kilometers (miles) of individual journeys. • Standard an[...]

empty indication, the amount of fuel that can be added will be less than the advertised capacity due to the reserve fuel. • Standard analog instrument cluster • Optional electronic instrument cluster Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the n[...]

• Optional electronic instrument cluster ELECTRONIC MESSAGE CENTER (IF EQUIPPED) The electronic message center only works when the ignition is in the ON position. The message center allows you to: • display the outside temperature. • change your gauges from english to metric units. • monitor the instantaneous fuel economy . • monitor the [...]

• OUTSIDE TEMP • INST ECONOMY • A VG ECONOMY • TO EMPTY RESET Press this control to reset the average fuel economy calculation. ENG/MET Press this control to change your instrument cluster gauges from english to metric. T o switch the Electronic Automatic T emperature Control (if equipped) display between Fahrenheit and Celsius, refer to T [...]

INST ECONOMY Press SELECT until the menu displays INST ECONOMY . This will display your fuel economy in liters/100 km or miles/gallon based on the type of traffic you are in. Y our vehicle must be moving to calculate instantaneous fuel economy . When your vehicle is not moving, this function shows 99.9 L/100km or 0.0 MILES/GAL. Instantaneous fuel e[...]

2. Select A VG ECONOMY . 3. Press the RESET control to clear the system memory . • Actual highway fuel economy is now displayed. This current average measure will change as the speed control system changes the engine speed to maintain a constant vehicle speed. This is most noticeable in hilly environments. 4. Drive the vehicle at least 8 km (5 mi[...]

P ANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel. • Push and hold top of control to brighten. • Push and hold bottom of control to dim. HEADLAMP CONTROL Rotate the headlamp control clockwise to the first position to turn on the parking lamps. Rotate clockwise to the second position to also turn on the headlamps. Push t[...]

High beams Push forward to activate. Pull toward you to deactivate. Flash to pass Pull toward you to activate and release to deactivate. AUTOLAMP CONTROL (IF EQUIPPED) The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control. The autolamp system also keeps the lights on[...]

CLIMATE CONTROL SYSTEM Manual heating and air conditioning system Fan speed control Controls the volume of air circulated in the vehicle. T emperature control Controls the temperature of the airflow inside the vehicle. Mode selector control Controls the direction of the airflow to the inside of the vehicle. A/C Control A/C T urns the A/C on in all [...]

The air conditioning operates in MAX A/C and when the A/C control is depressed. However , the air conditioning will only function if the outside temperature is about 4°C (40°F) or higher . Since the air conditioner removes considerable moisture from the air during operation, it is normal if clear water drips on the ground under the air conditione[...]

and air conditioning capabilities are provided in this mode. For added customer comfort, when the temperature control knob is anywhere in between the full hot and full cold positions, the air distributed through the front and rear floor ducts will be slightly warmer than the air sent to the windshield defroster ducts. If the outside temperature is [...]

Rear seat heating Rear seat heating is provided through the floor ducts located under the front seats. Airflow and temperature to the rear seating are regulated by the main climate control system. The rear passenger compartment air conditioning system (if equipped) should be set to OFF , if rear heating is desired. Operating tips • In humid weath[...]

• Remove any snow , ice or leaves from the air intake area (at the bottom of the windshield under the hood). • If your vehicle has been parked with the windows closed during hot weather , the air conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open. This will force most of the hot, stale a[...]

The rear A/C fan speed control allows the rear passengers to control the volume of air that is distributed from the rear registers. The rear seat A/C system is controlled from the main climate control system on the instrument panel. 0 1 2 3 4 REAR A/C OFF REAR A/C 1 2 3 4 1 MAX A/C OFF 2 3 4 A/C Controls and features 26[...]

T urning the Rear A/C on 1. Set the main climate control rear fan control to Rear A/C, set the mode selector in any position (other than OFF), and depress the A/C control. 2. Set the fan speed on the Rear A/C fan control to a number between 1–4. Front seat air flow regulation of the rear fan Set the main climate control rear fan control to a numb[...]

T urning the Rear A/C off: T o turn the Rear A/C off, turn the Rear Fan Control on the main climate control system to OFF , or turn the Rear Fan Control on the main climate control system to Rear A/C and turn the Rear A/C Fan Control to 0. For maximum cooling for the front seat passengers, set the rear fan switch to the OFF (0) position. Please not[...]

Electronic Automatic T emperature Control (EA TC) system (if equipped) The EA TC system will maintain a selected temperature and automatically control airflow . Y ou can override automatic operation with any of the override controls or the fan speed control. Turning the EA TC on Press AUTOMA TIC, any of the override controls or the fan speed contro[...]

Turning the EA TC off Press OFF . Automatic operation Press AUTOMA TIC and select the desired temperature. The selected temperature and the word AUTO will appear in the display window . The EA TC system will either heat or cool to achieve the selected temperature. The system will automatically determine fan speed, airflow location and if outside ai[...]

T o control the temperature, select any temperature between 15°C (60°F) and 32°C (90°F) by pressing the temperature controls. For continuous maximum cooling, push the temperature control until 15°C (60°F) is shown in the display window . The EA TC will continue maximum cooling (disregarding the displayed temperature) until a warmer temperatur[...]

Fan speed ( ) When AUTOMA TIC is pressed, fan speed is adjusted automatically for existing conditions. Y ou can override fan speed at any time. T o control fan speed manually , use the thumbwheel to cancel automatic fan speed operation. Rotate the thumbwheel up for higher fan speed or down for lower fan speed. The display will show to indicate manu[...]

Since the air conditioner removes considerable moisture from the air during operation, it is normal if clear water drips on the ground under the air conditioner drain while the system is working and even after you have stopped the vehicle. Under normal conditions, your vehicle’ s climate control system should be left in any position other than MA[...]

• MAX A/C-Uses recirculated air to cool the vehicle. MAX A/C is noisier than A/C A/C but more economical and will cool the inside of the vehicle faster . After pressing the MAX control, both the MAX and A/C A/C indicators will light and the airflow will be from the instrument panel registers. In this mode, the air conditioning will automatically [...]

Rear seat heating Rear seat heating is provided through the floor ducts located under the front seats. Airflow and temperature to the rear seating are regulated by the main climate control system. The rear passenger compartment air conditioning system (if equipped) should be set to OFF , if rear heating is desired. Operating tips • In humid weath[...]

• Remove any snow , ice or leaves from the air intake area (at the bottom of the windshield). • If your vehicle has been parked with the windows closed during hot weather , the air conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open. This will force most of the hot, stale air out of the v[...]

The rear A/C fan speed control allows rear passengers to control the volume of air that is distributed from the rear registers. The rear A/C system is controlled from the main climate control system on the instrument panel. The rear seat A/C system is controlled from the main climate control system on the instrument panel. 0 1 2 3 4 REAR A/C OFF RE[...]

T urning the Rear A/C on 1. Set the main climate control rear fan control to Rear A/C, set the mode selector in any position (other than OFF), and depress the A/C control. 2. Set the fan speed on the Rear A/C fan control to a number between 1–4. Front seat air flow regulation of the rear fan Set the main climate control rear fan control to a numb[...]

turn the Rear Fan Control on the main climate control system to Rear A/C and turn the Rear A/C Fan Control to 0. For maximum cooling for the front seat passengers, set the rear fan switch to the OFF (0) position. Please note that the rear passenger air conditioning system is designed for air conditioning purposes only , and does not heat the rear c[...]

The ignition must be in the ON position to operate the rear window defroster . The defroster turns off automatically after 15 minutes or when the ignition is turned to the OFF position. T o manually turn off the defroster before 15 minutes have passed, push the control again. USING YOUR AUDIO SYSTEM AM/FM Stereo/Cassette (CD changer compatible) V o[...]

T urn the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in radio, tape and CD changer modes (if equipped). AM/FM select in radio mode T[...]

Tune adjust in radio mode • Press to move to the next frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly . • Press to move to the next frequency up the band (whether or not a listenable station is located there). Hold for quick movement. Tune adjust for CD cha[...]

• Press to seek forward to the next track of the current disc. After the last track has been completed, the first track of the current disc will automatically replay . Scan function The scan function works in radio or CD changer mode (if equipped). Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stati[...]

Bass adjust The bass adjust control allows you to increase or decrease the audio system’ s bass output. Treble adjust The treble adjust control allows you to increase or decrease the audio system’ s treble output. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Speaker fade adjust Speaker s[...]

T ape select • T o enter tape mode while in radio or CD changer mode, press the T APE control. • If no tape is found, NO T APE appears in the display . Automatic Music Search The Automatic Music Search feature allows you to quickly locate the beginning of the tape selection being played or to skip to the next selection. T o activate the feature[...]

Press the 1–2/FF control to stop rewinding the tape. T o rewind in CD changer mode, press the CD control (preset 1). Press the control again to deactivate rewind mode. Fast forward The fast forward control works in tape and CD changer modes. T o fast forward in tape mode, press the 1–2/FF control. T ape direction will automatically reverse when[...]

The shuffle feature continues to the next disc after all tracks are played. Press the SHUFFLE control to start this feature. Random order play will continue until the SHUFFLE control is pressed again. T ape direction select Press SIDE and 1–2 at the same time to play the alternate side of a tape. Eject function Press the control to stop and eject[...]

• to decrease hours and • to increase hours. T o set the minute, press and hold the CLK control and press the TUNE control: • to decrease minutes and • to increase minutes. The CLK control will allow you to switch between media display mode (radio station, stereo information, etc.) and clock display mode (time). When in clock mode, the medi[...]

Rear seat controls (if equipped) The Rear Seat Controls (RSC) allow the rear seat passengers to operate the radio, tape, or CD changer (if equipped). T o turn on the rear seat controls, press the memory preset controls 3 and 5 at the same time. The will appear in the radio display . Pressing 3 and 5 at the same time again will turn the rear seat co[...]

Using headphones Plug a 3.6 mm headphone (not included) into either one of the two jacks. Press the / control to operate the headphones. The speakers will cut out once the speaker on/off control is pressed. Press the / control again to deactivate headphones. Media select Push the MEDIA control to toggle between AM, FM1, FM2, tape, or CD changer (if[...]

Premium AM/FM Cassette (CD changer compatible) Y our audio system is equipped with selective lighting, a unique lighting strategy . This lighting feature is operable when the headlamps are illuminated. During the operation of any selected mode, lighting for the individual function controls will either illuminate or turn off. Those controls which ha[...]

T urn the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in radio, tape and CD changer modes (if equipped). AM/FM select in radio mode T[...]

disc unless the CD changer is in shuffle mode.) Refer to Shuffle feature for more information. Hold the control to continue reversing through the disc. • Press to select the next disc in the CD changer . Hold the control to fast-forward through the remaining discs. Seek function The seek function control works in radio, tape or CD changer mode (i[...]

Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the SCAN control again to stop the scan mode. Scan function in tape mode Press the SCAN control to hear a short sampling of all selections on the tape. (The tape scans in a forward direction. At the end of the tape’ [...]

Starting autoset memory preset 1. Select a frequency using the AM/FM select controls. 2. Press the AUTO control. 3. When the first six strong stations are filled, the station stored in memory preset control 1 will start playing. If there are less than six strong stations available on the frequency band, the remaining memory preset controls will all[...]

Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. T ape/CD changer mode select (if equipped) • T o begin tape play (with a tape loaded into the audio system) while in the radio or CD changer mode, press the T APE control. Press the button during rewind or fast forward to stop the rewind or fast forward functio[...]

• In CD changer mode, pressing the control for less than three seconds results in slow forward action. Pressing the control for more than three seconds results in fast forward action. T ape direction select Press SIDE 1–2 to play the alternate side of a tape. Eject function Press the control to stop and eject a tape. Dolby T noise reduction Dol[...]

Press the SHUFFLE control to start this feature. Random order play will continue until the SHUFFLE control is pressed again. Radio Data System (RDS) feature When selected, the RDS (Radio Data System) function performs the following: • Displays the radio station call letters • Displays the type of music format (jazz, country , rock) • Searches[...]

• Use the SEL control to select the program type. W ith the feature on, use the SEEK or SCAN control to find the desired program type from the following selections: • Classic • Country • Info • Jazz • Oldies • R&B • Religious • Rock • Soft • To p 4 0 Show • W ith RDS activated, press the RDS control until SHOW is display[...]

Use the SEL control to manually set the time. • Press to increase hours/minutes. • Press to decrease hours/minutes. Mute mode Press the control to mute the playing media. Press the control again to return to the playing media. Rear seat controls (if equipped) The Rear Seat Controls (RSC) allow the rear seat passengers to operate the radio, tape[...]

Adjusting the volume Press the + control to increase volume. Press the — control to decrease volume. From the RSC, the speaker volume can not be set higher than the current volume radio setting. Once in headphone mode, the RSC volume controls will only change volume in the headphones to a desired level (muting the speakers will not mute the headp[...]

Memory preset control Push the MEM control successively to allow rear sear passengers to scroll through the 6 memory presets in AM, FM1, or FM2. Push the MEM control in CD changer mode (if equipped) to advance to the next disc. Seek function • Press to find the next listenable station down the frequency band. • Press to find the next listenable[...]

Y our audio system is equipped with selective lighting, a unique lighting strategy . This lighting feature is operable when the headlamps are illuminated. During the operation of any selected mode, lighting for the individual function controls will either illuminate or turn off. Those controls which have a function for the specific mode of operatio[...]

AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. AM/FM select in tape mode Press this control to stop tape play and begin radio play . AM/FM select in CD mode Press this control to stop CD play and begin radio play . Tune adjust The tune[...]

Seek function in radio mode • Press to find the next listenable station down the frequency band. • Press to find the next listenable station up the frequency band. Seek function in tape mode • Press to listen to the previous selection on the tape. • Press to listen to the next selection on the tape. Seek function for CD changer (if equipped[...]

Scan function in tape mode Press the SCAN control to hear a short sampling of all selections on the tape. (The tape scans in a forward direction. At the end of the tape’ s first side, direction automatically reverses to the opposite side of the tape.) T o stop on a particular selection, press the control again. Scan function in CD mode Press the [...]

Starting autoset memory preset 1. Select a frequency using the AM/FM select controls. 2. Press the AUTO control. 3. When the first six strong stations are filled, the station stored in memory preset control 1 will start playing. If there are less than six strong stations available on the frequency band, the remaining memory preset controls will all[...]

• to decrease treble output and • to increase treble output. Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Press the BAL control then press: • to shift sound to the left and • to shift sound to the right. Speaker fade adjust Speaker sound can be adjusted between the front and rear spe[...]

T ape/CD/CD changer (if equipped) select • T o begin tape play (with a tape loaded into the audio system) while in the radio or CD mode, press the T APE control. Press the button during rewind or fast forward to stop the rewind or fast forward function. • T o begin CD play (if CD(s) are loaded), press the CD control. The first track of the disc[...]

T ape direction select Press SIDE 1–2 to play the alternate side of a tape. Eject function Press the control to stop and eject a tape. Press the control to stop and eject a CD. Dolby noise reduction Dolby noise reduction reduces the amount of hiss and static during tape playback. Press the control to activate (and deactivate) the noise reduction.[...]

Setting the clock Press the RDS/CLK control until SELECT HOUR is displayed and press: • to decrease hours and • to increase hours. T o set the minute, press the RDS/CLK control until SELECT MIN is displayed and press: • to decrease minutes and • to increase minutes. Radio Data System (RDS) feature When selected, the RDS (Radio Data System) [...]

Press the RDS control. Use the SEL control to select ON or OFF to enable or disable the feature. RDS traffic announcement When set ON, this traffic feature will interrupt tape or CD play to play a traffic report broadcast from a FM RDS station. T o activate the traffic feature: • Press the RDS control until TRAFFIC is displayed. T o see if any st[...]

• Jazz/R&B • Religious • Rock • Soft • To p 4 0 RDS show RDS sends information with the FM broadcast, including: station name, station type, and/or radio text. T o view this information: • W ith the RDS menu enabled, press the RDS control until SHOW is displayed. • Use the SEL control to select TYPE, NAME, TEXT or NONE. When your [...]

T o turn on the rear seat controls, press the memory preset controls 3 and 5 at the same time. The will appear in the radio display . Pressing 3 and 5 at the same time again will turn the rear seat controls off. If there is a discrepancy between the rear seat and the front audio controls, (i.e, both trying to listen to the same playing media), the [...]

The rear speakers will cut out once the speaker on/off control is pressed. A soft audible sound may be heard from the rear speakers. The front speaker will remain playing for the front passengers. Press the / control again to deactivate headphones (Personal Audio System). Media select Push the MEDIA control to toggle between AM, FM1, FM2, tape, CD,[...]

CD changer (if equipped) The CD changer is located in the center console of your vehicle. 1. Slide the door to access the CD changer magazine. 2. Press to eject the magazine. 3. T urn the magazine (A) over . 4. Using the disc holder release knob (C), pull the disc holder (B) out of the magazine. A B C Controls and features 76[...]

If you pull too hard on the disc holder , the disc holder may come completely out of the magazine. If this happens, reinsert the disc holder back into the magazine while pressing on the lever (A). 5. Line up the CD with the groove of the disc holder . Ensure that the label on the CD faces downwards. 6. Press in on the disc holder until it locks sec[...]

The CD magazine may be inserted or ejected with the radio power on or off. ONL Y use the magazine type supplied with the CD changer , other types will damage the unit. Keep the CD changer door closed. Coins and foreign objects will damage the CD player and void your audio system warranty . Do not insert any promotional (odd shaped or sized) discs i[...]

Cleaning cassette player Clean the tape player head with a cassette cleaning cartridge after ten to twelve hours of play in order to maintain the best sound and operation. Cassette and cassette player care • Use only cassettes that are 90 minutes long or less. • Do not expose tapes to direct sunlight, high humidity , extreme heat or extreme col[...]

• Station overload. W eak signals are sometimes captured by stronger signals when you pass a broadcast tower . A stronger signal may temporarily overtake a weaker signal and play while the weak station frequency is displayed. The audio system automatically switches to single channel reception if it will improve the reception of a station normally[...]

POSITIONS OF THE IGNITION 1. OFF/LOCK, shuts off the engine and all accessories/locks the steering wheel, gearshift lever and allows key removal. 2. ACC, allows the electrical accessories such as the radio to operate while the engine is not running. 3. ON, all electrical circuits operational. W arning lights illuminated. Key position when driving. [...]

T o turn speed control off • Press OFF . Once speed control is switched off, the previously programmed set speed will be erased. T o set a speed • Press COAST/SET . For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph). If you drive up or down a steep hill, your vehicle speed may [...]

T o set a higher set speed • Press and hold RES/ACCEL. Release the control when the desired vehicle speed is reached or • Press and release RES/ACCEL. Each press will increase the set speed by 1.6 km/h (1 mph) or • Accelerate with your accelerator pedal. When the desired vehicle speed is reached, press and release COAST/SET . Y ou can acceler[...]

T o disengage speed control • Depress the brake pedal. • Press CANCEL. Disengaging the speed control will not erase the previously programmed set speed. • Press OFF . Pressing OFF will erase the previously programmed set speed. CANCEL RES ACCEL COAST SET CRUISE OFF Controls and features 84[...]

T o return to a previously set speed • Press RES/ACCEL. For RES/ACCEL to operate, the vehicle speed must be faster than 48 km/h (30 mph). Indicator light This light comes on in the instrument cluster when either the COAST/SET or RES/ACCEL controls are pressed. It turns off when the speed control OFF control is pressed, the brake is applied or the[...]

In any mode: • Press VOL up or down to adjust the volume. TURN SIGNAL CONTROL • Push down to activate the left turn signal. • Push up to activate the right turn signal. WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper control to the desired interval, low or high speed position. The bars of varying length are for intermittent wiper[...]

Rear window wiper and washer Press the wiper control to activate the rear wiper . Press again to turn off the wiper . The wiper operates at a pre-set interval. Press the washer control to activate the rear washer . The wiper will come on when the washer control is pressed, if it is not already on. HAZARD FLASHER For information on the hazard flashe[...]

Deactivating overdrive Press the T ransmission Control Switch (TCS) located on the end of the gearshift lever . The O/D OFF indicator light will illuminate. The transaxle will operate in all gears except overdrive. T o return to normal overdrive mode, press the T ransmission Control Switch again. The O/D OFF indicator light will no longer be illumi[...]

POWER WINDOWS • Press and hold the switch to open. • Pull up and hold the switch to close. Power vent windows (if equipped) Y our vehicle may be equipped with rear power vent windows which are operated the same as the front power windows. One touch down • Press AUTO completely down and release quickly . The driver’ s window will open fully [...]

Accessory delay W ith accessory delay , the window and moonroof switches may be used for up to 15 minutes after the ignition switch is turned to the OFF position or until either of the front doors are opened. POWER DOOR LOCKS Push control forward to unlock all doors and pull backward to lock all doors. Anti-lockout This feature prevents the front d[...]

Pull lock control out to engage the lock. Push control in to disengage childproof locks. POWER SIDE VIEW MIRRORS The ignition must be in ACC or ON position to adjust the power side view mirrors. T o adjust your mirrors: 1. Select L to adjust the left mirror or R to adjust the right mirror . MIRRORS L R Controls and features 91[...]

2. Move the control in the direction you wish to tilt the mirror . 3. Return to the center position to lock mirrors in place. Heated outside mirrors (if equipped) Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. Do not remove ice from the mirrors with a scraper or attempt to readjust the m[...]

HOMELINK T UNIVERSAL T RANSCEIVER WITH T RAVELNOTE T (IF EQUIPPED) The HomeLink t Universal T ransceiver , located on the driver’ s visor , provides a convenient way to replace up to three hand-held transmitters with a single built-in device. This feature will learn the radio frequency codes of most current transmitters to operate garage doors, e[...]

4. The red light will flash slowly and then rapidly . Release both buttons when the red light flashes rapidly . 5. Follow steps 2 through 4 to program the remaining two buttons. If you do not successfully program the HomeLink t Universal T ransceiver after repeated attempts, refer to Rolling code programing which follows, or call toll-free customer[...]

• The hand-held transmitter appears to program the HomeLink t Universal T ransceiver but does not activate the device. • Press and hold the trained HomeLink t button. The device has the rolling code feature if the indicator light flashes rapidly and then turns solid after 2 seconds. After completing the “Programming” functions, follow these[...]

1. Press and hold the desired HomeLink t button. Do NOT release until step 4 has been completed. 2. When the indicator light begins to flash slowly (after 20 seconds), position the hand-held transmitter 5–14 cm (2 to 5 inches) away from the HomeLink t surface. 3. Press and hold the hand-held transmitter button. 4. The HomeLink t indicator light w[...]

T o play a message: 1. Press and release the PLA Y button to play the message. 2. Press and hold the PLA Y button to hear all the messages in consecutive order starting with the most recent. 3. If the PLA Y button is pressed while a message is being listened to, T ravelNote will skip to the beginning of the next message. 4. During all PLA Y functio[...]

Storage bin (if equipped) The storage compartment may be used to store small objects. Push in to open or close the cover . Installing a garage door opener (if equipped) The storage compartment can be converted to accommodate a variety of aftermarket garage door openers: • Remove the GARAGE control button from the storage compartment. • Place V [...]

• Place the provided height adaptors on the back of the GARAGE control button as needed. • Place the GARAGE control button in the storage compartment. • Close cover and press the GARAGE control button to activate the transmitter . INTERIOR LAMPS Dome lamps The front dome lamp is located overhead between the driver and passenger seats. The dom[...]

MOON ROOF (IF EQUIPPED) T o operate the moon roof: • T o open, press and hold the rear portion of the control. This will fully open the moon roof. • T o close, press and hold the front portion of the control. T o operate the moon roof vent position: • T o open, press and hold the front portion of the control. This will open the vent. • T o [...]

Unlocking the doors Press this control to unlock the driver’ s door . The interior lamps will illuminate and the parking and tail lamps will flash once. Press the control a second time within five seconds to unlock all doors. Locking the doors Press this control to lock all doors. T o confirm all doors are closed and locked, the horn will chirp a[...]

This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly [...]

T o replace the battery: 1. T wist a thin coin between the two halves of the transmitter near the key ring. DO NOT T AKE THE FRONT P ART OF THE TRANSMITTER AP ART . 2. Place the positive (+) side of new battery up. Refer to the diagram inside the transmitter unit. 3. Snap the two halves back together . Replacing lost transmitters T ake all your veh[...]

ANTI-THEFT SYSTEM (IF EQUIPPED) When armed, the anti-theft system will help prevent your vehicle from unauthorized entry . If there is any potential perimeter anti-theft problem with your vehicle, ensure ALL key fobs (remote entry transmitters) are brought to the dealership, to aid in troubleshooting. Arming the system When unauthorized entry occur[...]

If a door is open, the system is prearmed and is waiting for the door to close. Once all the doors are closed, the security indicator lamp on the instrument panel will illuminate continuously when the system is prearmed. Once the doors are closed, the system will arm in 30 seconds and the security indicator lamp will begin to flash. Disarming the a[...]

Disarming a triggered anti-theft system Y ou can disarm the system by any of the following actions: • Press the unlock control. • Unlock the doors with a key . LIFTGATE T o open the liftgate window (if equipped), insert key into lock and turn clockwise. The window unlatches and the wiper moves out of the way . T o open the liftgate, insert key [...]

Make sure that the liftgate door and/or window are closed to prevent exhaust fumes from being drawn into the vehicle. This will also prevent passengers and cargo from falling out. If you must drive with the liftgate door or window open, keep the vents open so outside air comes into the vehicle. CARGO AREA FEA TURES Rear Cargo net The cargo net help[...]

Front Cargo net The front cargo net can be used to hold small items between the front seats. T o install the net, secure the hooks into the retainers located on the inboard base of the front seats. Parcel Shelf (if equipped) Y our vehicle may be equipped with a 14 kg (30 lbs.) maximum capacity parcel shelf located behind the rear seat of your vehic[...]

T o secure objects on the shelf: 1. Disconnect the net loops from the retainers underneath the shelf. 2. Place the objects underneath the net and secure the net loops to the retainers underneath the shelf. All objects loaded on the cargo shelf MUST BE SECURED UNDER THE CARGO NET . The net is permanently attached to the cargo shelf. Do not load more[...]

SEA TING Adjustable head restraints Y our vehicle’ s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. T o properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as[...]

Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Reclining the seatback can reduce the effectiveness of the seat’ s safety belt in the event of a collision. Lift handle to move seat forward or backward. Pull lever up to adjust seatback. Adjusting the power seats (if equipped) The power seat controls [...]

Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Reclining the seatback can reduce the effectiveness of the seat’ s safety belt in the event of a collision. Move the control up or down to move the seat up and down. • 6 way (driver seat) Slide the control forward or backward to move the seat forward[...]

The lumbar control is located on the inboard side of the driver’ s seat. Move the control up or down to adjust lumbar support. Memory seats and mirrors (if equipped) The memory seat control is located on the driver’ s door panel. The control operates with the ignition in the OFF position or the ignition is in the ON position and the vehicle is [...]

2. Press and hold the desired memory position button. W ithin ten seconds, press the unlock button on the transmitter while the memory button is pressed. 3. When the transmitter has been programmed, the indicator will flash five times. The indicator light will remain illuminated until the memory button is pressed again or ten seconds lapse. T o rem[...]

• 4 passenger vehicle (with third row seat in storage position) A. Cargo mat B. Narrow mats C. Sliding door mats, LH/RH • 5 passenger vehicle (second row seats removed) A. Cargo mat B. Narrow mats C. Sliding door mats, LH/RH A B C B B A B C Seating and safety restraints 115[...]

• 5 passenger vehicle (second row seats removed and third row bench seat moved forward to limousine seating position) A. Cargo mat B. Narrow mats • T wo passenger vehicle (second row seats removed and third row seat stored in full forward position) A. Cargo mat B. Narrow mats Stowed cupholders The vehicle is equipped with cupholders that pull o[...]

• Bucket seat (driver’ s side only) - inboard side of seat base Use only soft cups in the cupholder . Hard objects can injure you in a collision. Adjusting 2nd row bench Pull control up to flip seatback to forward flat position. Seating and safety restraints 117[...]

2nd row bucket seats (if equipped) • Adjusting the left side bucket seat Pull control up to recline the seatback or fold the seatback flat. • Adjusting the right side (E-Z Entry T ip Slide) bucket seat The E-Z Entry T ip Slide seat allows for easier entry and exit to and from the 3rd row seat. The E-Z Entry system will slide the seat and tip th[...]

T o exit the third row seat, pull up on the 3rd row access control. T o return the seat to a seating position, move the seat rearward until the seat track locks. Then readjust the seatback. Lift handle to move the seat forward or backward. Seating and safety restraints 119[...]

Pull control up to flip seatback to a forward flat position. Adjusting 3rd row bench Pull control up to adjust seatback position. This control will also allow the seatback to be put in the forward flat position. Seating and safety restraints 120[...]

The entire seat can be moved to four seating positions and two storage positions. Before rearranging the seats, remove any floor mats that might be in the way , see Removable floor mats in this chapter for instructions on placement of floor mats. For vehicles equipped with a second row bench seat: If the three passenger bench seat is moved up to th[...]

T o move the seat to another seating or storage position: 1. Lift control (A) to release the seat cushion and flip the cushion up. The seat cushion must be moved to the storage position before the seat can be moved along the track. 2. Pull control (B) to move the seat forward or backward until it locks into position. The seat cushion cannot be lowe[...]

After sliding the seat, check to ensure that both sides of the seat are locked in position. This must be done before the vehicle is put into motion in order to prevent unintended movement of the seat. Every time you adjust any seat, check to be sure that it is properly latched in the lock position of both seat tracks. If the seat is not properly la[...]

T o install the seat: The bucket seats are not interchangeable due to the locations of the seat anchors on the floor of the vehicle. Each seat must be installed in its original position. 1. Position the seat in the vehicle. 2. Align seat front hooks to front anchors and push forward into place, lower back of seat into the rear anchors until both re[...]

It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety [...]

2. T o unfasten, push the release button and remove the tongue from the buckle. The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts. The front passenger and rear seat outboard safety belts have two types of locking modes described below: V ehicle sensitive mode The vehicle sensitive mode is the normal[...]

How to use the automatic locking mode • Buckle the combination lap and shoulder belt. • Grasp the shoulder portion and pull downward until the entire belt is extracted. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How to disengage the au[...]

Front safety belt height adjustment Y our vehicle has safety belt height adjustments for the driver and front passenger . Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder . T o lower the shoulder belt height, push the button and slide the height adjuster down. T o raise the height of the shoulder belt, sli[...]

Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from). T o lengthen the belt, turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle. T o tighten the belt, pull the loose end of the belt through the tongue until it fits snugly across the hips. Shorten and[...]

Conditions of operation If... Then... The driver’ s safety belt is not buckled before the ignition switch is turned to the ON position... The safety belt warning light illuminates until safety belt is buckled. The driver’ s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding... The safety belt warni[...]

AIR BAG SUPPLEMENT AL RESTRAINT SYSTEM (SRS) Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Air bags DO NOT inflate slowly or gently and the risk of injury from a deploying air [...]

National Highway T raffic Safety Administration (NHTSA) recommends a minimum distance of at least 25 cm (ten [10] inches) between an occupant’ s chest and the driver air bag module. Never place your arm over the air bag module as a deploying air bag can result in serious arm fractures or other injuries. Steps you can take to properly position you[...]

Children and air bags For additional important safety information, read all information on safety restraints in this guide. Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position. Failure to follow these instructions m[...]

The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the air bag. Small [...]

The diagnostic module monitors its own internal circuits and the supplemental air bag electrical system warning (including the impact sensors), the system wiring, the air bag system readiness light, the air bag back up power and the air bag ignitors. Determining if the system is operational The SRS uses a readiness light in the instrument cluster t[...]

Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. Always follow the instructions and warnings that come with any infant or child restraint you might use. When possible, always place children under age 12 in the rear seat of your vehicle. Accident stat[...]

SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child. Carefully follow all of the manufacturer’ s instructions with the safety seat you put in your vehicle. If you do not install and use the safety seat properly , the child may be injured in a sudden stop or co[...]

Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage. For more information on top tether straps, refer to Attaching safety seats with tether straps. Carefully follow all of the manufacturer’ s instructions included with the sa[...]

2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the b[...]

5. T o put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode. 7. Pull the lap belt portion across the child seat toward the buck[...]

Installing child safety seats in the lap belt seating positions 1. Lengthen the lap belt. T o lengthen the belt, hold the tongue so that its bottom is perpendicular to the direction of webbing while sliding the tongue up the webbing. 2. Place the child safety seat in the center seating position. 3. Route the tongue and webbing through the child sea[...]

Seat T ype/Position T ether to... Reference Section 3-passenger/3rd row position Floor anchor directly behind child seat position 3rd row seats 2-passenger bench or bucket/2nd row child seat position Directly to the rear of the second row seats 2nd row seats 3-passenger/2nd row –Outboard T ongue of 3rd row belt directly behind child seat position[...]

Second row seats 1. Position the child safety seat on the passenger seat cushion. 2. Route the child safety seat tether strap over the back of the seat. 3. Grasp the tether strap and position it to the seat frame. Seating and safety restraints 143[...]

4. Rotate the tether strap. 5. Clip the tether strap to the seat tether slot bracket at the lower rear portion of the seatback. If the tether strap is clipped incorrectly (as shown) the child safety seat may not be retained properly in the event of a collision. Seating and safety restraints 144[...]

6. Rotate the tether strap clip. 7. Refer to the instructions in this section under Installing child safety seats in combination lap and shoulder belt seating positions to secure the child safety seat. 8. T ighten the child safety seat tether strap according to the manufacturer’ s instructions. Seating and safety restraints 145[...]

Third row seat and tether anchorage hardware The tether has to be attached to the anchorage locations on the floor behind the third row seating position (third row seat only) with a tether anchorage hardware kit. T ether anchorage hardware kits (part number 613D20) including instructions, may be obtained at no charge from any Ford or Lincoln-Mercur[...]

Third row bench in second row position T o attach a tether strap to a lap/shoulder belt: 1. Route the tether strap under the head restraint and between the head restraint supports. 2. Hook the tether strap hook into the large hole at the end of the seat belt tongue of the lap/shoulder belt directly behind the child seat position. 3. Adjust the teth[...]

BUIL T -IN CHILD SEA TS Built-in child safety seat (if equipped) The 2nd row seat may include a built-in child seat. This child seat conforms to all Federal and local motor vehicle safety standards. Read the labels located on the child seat cushion for information on the built-in child seat. Use the built-in child seat only if the child is at least[...]

1. Pull the release strap near the bottom of the seatback. 2. Grasp the child seat at the top of the seatback and pull the top forward to release the latch. 3. Continue to unfold the child seat until it rests on the seat. Seating and safety restraints 149[...]

4. Read all information and warnings on the child seat cushion and shoulder safety belt. The child seat is to be used only by children who: • are at least one year old • weigh between 10 and 27 kg (22 and 60 lbs.) • shoulders must be below the shoulder harness slots 5. If connected, squeeze the top and the bottom of the right half of the ches[...]

10. Pull the right shoulder belt fully out to put the retractor into the automatic locking mode. 11. If the belts become too tight, unbuckle the crotch safety belt buckle to unlock the retractors, then reinsert both belt tongues. Removing your child from the built-in child seat 1. Squeeze the tabs on the top and the bottom of the chest clip and pul[...]

PREPARING TO START YOUR VEHICLE Engine starting is controlled by the ignition system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting. Only use the accele[...]

2. Make sure the headlamps and vehicle accessories are off. 3. Make sure the parking brake is set. 4. Make sure the gearshift is in P (Park). 5. T urn the key to 3 (ON) without turning the key to 4 (ST ART). If there is difficulty in turning the key , firmly rotate the steering wheel left and right until the key turns freely . This condition may oc[...]

Make sure the corresponding lights illuminate briefly . If a light fails to illuminate, have the vehicle serviced. • If the driver’ s safety belt is fastened, the light may not illuminate. ST ARTING THE ENGINE 1. T urn the key to 4 (ST ART) without pressing the accelerator pedal and release as soon as the engine starts. The key will return to 3[...]

Using the engine block heater (if equipped) An engine block heater warms the engine coolant, which improves starting, warms up the engine faster and allows the heater -defroster system to respond quickly . Use of an engine block heater is strongly recommended if you live in a region where temperatures reach -23°C (-10°F) or below . For best resul[...]

Important ventilating information If the engine is idling while the vehicle is stopped in an open area for long periods of time, open the windows at least 2.5 cm (one inch). Adjust the heating or air conditioning to bring in fresh air . Improve vehicle ventilation by keeping all air inlet vents clear of snow , leaves and other debris. Starting 156[...]

BRAKES Y our service brakes are self-adjusting. Refer to the scheduled maintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’ s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the b[...]

ABS warning lamp The ABS warning lamp in the instrument cluster momentarily illuminates when the ignition is turned to the ON position. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced. W ith the ABS light on, the anti-lock brake system is disabled and normal braking is still e[...]

The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is released. Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park). The parking brake is not recommended to stop a moving vehicle. However , if the normal brakes [...]

• high crown in center of road • high crosswinds • wheels out of alignment • loose or worn components in steering linkage AUTOMATIC TRANSAXLE OPERATION Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) unless the brake pedal is depressed. If y[...]

Understanding gearshift positions T o account for customer driving habits and conditions, your automatic transaxle electronically controls the shift feel by using an adaptive learning strategy . During the first few hundred kilometers (miles) of operation, it is normal for your transaxle to have abrupt shifts. The adaptive learning strategy is main[...]

automatic overdrive transaxle. When your vehicle cruises at a constant speed for any length of time, this fourth gear will increase your fuel economy . Overdrive may not be appropriate for certain terrains. If the transaxle shifts back and forth between third and fourth gears while you are driving hilly roads or if your vehicle requires additional [...]

second and third gears and will not shift into fourth gear . Operating in D (O/D OFF) provides more engine braking than Overdrive for descending hills or city driving. T o return the transaxle to the normal Overdrive operation, press the O/D OFF control again. Use this control to select between Overdrive or D (O/D OFF) whenever you drive your vehic[...]

Driving with an automatic overdrive transaxle Y our automatic transaxle electronically controls the shift feel by using an adaptive learning strategy . This feature is designed to optimize shift smoothness. It is normal for your transaxle to shift firmly during the first few hundred kilometers (miles) of operation until the adaptive strategy has be[...]

V EHICLE LOADING Before loading a vehicle, familiarize yourself with the following terms: • Base Curb W eight : W eight of the vehicle including any standard equipment, fluids, lubricants, etc. It does not include passengers or aftermarket equipment. • Payload : Combined maximum allowable weight of cargo, passengers and optional equipment. The [...]

Do not use replacement tires with lower load carrying capacities than the originals because they may lower the vehicle’ s GVWR and GA WR limitations. Replacement tires with a higher limit than the originals do not increase the GVWR and GA WR limitations. The Certification Label, found on the inside pillar of the driver’ s door , lists several i[...]

The optional T railer T ow Prep Package is recommended for towing of any trailer since it provides a heavy duty battery , conventional size spare tire and wiring. T railer towing puts additional loads on your vehicle’ s engine, transmission, axle, brakes, tires, and suspension. For your safety and to maximize vehicle performance, be sure to use t[...]

Preparing to tow Use the proper equipment for towing a trailer , and make sure it is properly attached to your vehicle. See your dealer or a reliable trailer dealer if you require assistance. Hitches For towing trailers up to 907 kg (2 000 lb), use a weight carrying hitch and ball which uniformly distributes the trailer tongue load through the unde[...]

Trailer lamps T railer lamps are required on most towed vehicles. Make sure your trailer lamps conform to local and Federal regulations. See your dealer or trailer rental agency for proper instructions and equipment for hooking up trailer lamps. Driving while you tow Do not drive faster than 88 km/h (55 mph) when towing a trailer . Speed control ma[...]

LUGGAGE RACK The front and rear crossbar can be adjusted to fit the item being carried. Do not load more than 44 kg (100 lbs.) on the luggage rack. T o adjust cross-bar position: 1. Loosen the thumbwheel at both ends of the cross-bar . 2. Slide the cross-bar to the desired location. 3. T ighten the thumbwheel at both ends of the cross-bar . Use adj[...]

HAZARD FLASHER Use only in an emergency to warn traffic of vehicle breakdown, approaching danger , etc. The hazard flashers can be operated when the ignition is off. • The hazard lights control is located on the instrument panel. • Depress hazard lights control to activate all hazard flashers simultaneously . • Depress control again to turn t[...]

The fuel pump shut-off switch is located in the driver’ s foot well, behind the kick panel. The reset button for the fuel pump shut-off switch is accessible through an opening in the kick panel. Use the following procedure to reset the fuel pump shut-off switch. 1. T urn the ignition to the OFF position. 2. Check the fuel system for leaks. 3. If [...]

Standard fuse amperage rating and color COLOR Fuse Rating Mini Fuses Standard Fuses Maxi Fuses Cartridge Maxi Fuses Fuse Link Cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A T an T an — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Y ellow Y ellow Y ellow Blu[...]

The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Description Corner Lamps 10A Front Exterior Lamps — — Not Used I/P Illum 7.5A Interior Panel Illumination Lamps Electron 10A T ransaxle Control Module (TCM), Electronic Automatic T emperature Control (EA TC) Module, Instrument Cluster , Rear W iper Motor Assembly T ail Lamp 10A[...]

Fuse/Relay Location Fuse Amp Rating Description Room Lamp 15A Interior Lamps Mirror 7.5A Smart Entry Control (SEC), Power Mirror Switch Stop Lamp 20A Brake Pedal Position (BPP) Switch, T railer T ow Control Unit Cigar Lighter 20A Cigar Lighter Hazard 10A Hazard W arning Flasher Switch, Anti-Theft Indicator RR Pwr Plug 20A Rear Powerpoint Rear Blowe[...]

Fuse/Relay Location Fuse Amp Rating Description Electron 10A T ransmission Control, Lighting Control Module, ABS Control Module, Smart Entry Control (SEC)/T imer Module Rear Defog 20A Rear W indow Defrost Front Blower 20A Front Blower Motor , Front Blower Motor/Speed Controller Rear Defog 20A Rear W indow Defrost — — Not Used Heated Mirror 10A [...]

The high-current fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Description — — Not Used FUEL PUMP 15A* Fuel Pump Relay INJ 10A* Powertrain Control Module (PCM), Injectors SEC 7.5A* Anti-Theft Relay , Smart Entry Control (SEC)/T imer Module RAD 7.5A* Radiator Fan Sensing ECCS 10A* Data Link Connector (DLC) #1, PCM Power Relay ?[...]

Fuse/Relay Location Fuse Amp Rating Description ABS 20A* ABS Control Module — — Not Used H/L RH 15A* Lighting Control Module HORN 15A* Horn Relay — — Not Used H/L LH 15A* Lighting Control Module — — Not Used — — Not Used ABS 40A** ABS Control Module — — Not Used PWR WND 30A** Power Window Relay , Smart Entry Control (SEC)/T imer[...]

Relay box The relay box is located in the engine compartment in front of the battery . The relays are coded as follows: Relay location Description 1 Start Inhibit Relay 2 Fuel Pump Relay 3 Bulb Check Relay 4 Speed Control Hold Relay 5 Anti-theft Relay 6 Horn Relay 7 A/C Relay CHANGING THE TIRES If you get a flat tire while driving, do not apply the[...]

T emporary spare tire information Y our vehicle may have a temporary or conventional size spare tire. The temporary spare tire for your vehicle is labeled as such. It is smaller than a regular tire and is designed for emergency use only . Replace this tire with a full-size tire as soon as possible. If you use the temporary spare tire continuously o[...]

Removing the spare tire 1. Open the liftgate, locate the U-shaped slits in the carpet, and flip up the piece of carpet to expose the hex nut. 2. Insert the lug nut wrench on the hex nut in cargo floor . 3. T urn the wrench counterclockwise until tire is lowered to the ground and the cable is slightly slack. 4. Remove the retainer from the spare tir[...]

Stowing the spare 1. Lay the tire on the ground with the interior side facing up. 2. Install the retainer through the wheel center and slide the wheel under the vehicle. 3. T urn the wrench clockwise until the tire is raised to its original position underneath the vehicle. The hex nut ratchets when the tire is raised to the stowed position. It will[...]

1. Park on a level surface, activate hazard flashers and set parking brake. 2. Place gearshift lever in P (Park), turn engine OFF , and block the diagonally opposite wheel. 3. Remove the spare tire and jack assembly . 4. Remove the center ornament or wheel cover from the wheel with the tapered end of the jack handle that came with your vehicle. Ins[...]

Jacking notches are located approximately six inches rearward of the front wheels and twelve inches foward of the rear wheels. 6. Locate the jack notch closest to the tire you are changing, then place the jack on the frame rail directly behind the notch. 7. T urn the jack handle clockwise until the wheel is completely off the ground. T o lessen the[...]

JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Do not push start your vehicle. Y ou could damage the catalytic converter . Batteries contain sulfuric acid which can burn skin, eyes, and clothing, if contacted. Do not attempt [...]

Connecting the jumper cables 1. Connect the positive (+) booster cable to the positive (+) terminal of the discharged battery . Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery . 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery . + – + – + [...]

3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery . 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’ s engine, away from the battery and the carburetor/fuel injection system. The preferred locations of an exposed metal part (to ground the circuit) are the[...]

Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables. Removing the jumper cables Remove the jumper cables in the rev[...]

3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery . After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle c[...]

WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member , your roadside assistance center . It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure. If your vehicle [...]

SERVICE RECOMMENDATIONS T o help you service your vehicle: • W e highlight do-it-yourself items in the engine compartment for easy location. • W e provide a Scheduled Maintenance Guide which makes tracking routine service easy . If your vehicle requires professional service, your dealership can provide necessary parts and service. Check your ?[...]

Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hoo[...]

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 3.3L V6 engine 1. Power distribution box 2. Brake fluid reservoir 3. Air filter assembly 4. Battery 5. Relay box 6. Engine oil filler cap 7. Engine oil dipstick 8. W indshield washer fluid reservoir 9. Engine coolant reservoir 10. Power steering fluid reservoir 11. Automatic transmission fluid dipsti[...]

ENGINE OIL Checking the engine oil Refer to the Scheduled Maintenance Guide for the appropriate intervals for checking the engine oil . 1. Make sure the vehicle is on level ground. 2. T urn the engine off and wait a few minutes for the oil to drain into the oil pan. 3. Set the parking brake and ensure the gearshift is securely latched in P . 4. Ope[...]

• If the oil level is below the L mark, add enough oil to raise the level within the L and H range. • Oil levels above the H mark may cause engine damage. Some oil must be removed from the engine by a service technician. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions, refe[...]

Engine oil and filter recommendations Look for this Certification T rademark. Use SAE 5W -30 motor oil certified for gasoline engines by the American Petroleum Institute (API). Motor oil displaying the API Certification T rademark will meet all requirements for your vehicle’ s engine. Ford oil specification is WSS-M2C153-G. Do not use supplementa[...]

BRAKE FLUID Checking and adding brake fluid Brake fluid should be checked and refilled as needed. Refer to the Scheduled Maintenance Guide for the service interval schedules: 1. Clean the reservoir cap before removal to prevent dirt or water from entering the reservoir . 2. Visually inspect the fluid level. 3. If necessary , add brake fluid until t[...]

WINDSHIELD WASHER FLUID Checking and adding washer fluid Check the washer fluid whenever you stop for fuel. The reservoir is highlighted with a symbol. If the level is low , add enough fluid to fill the reservoir . In very cold weather , do not fill the reservoir all the way . Do not put washer fluid in the reservoir for the engine coolant Checking[...]

The engine coolant must be maintained at the correct fluid level and concentration to work properly . If the engine coolant fluid level and concentration is not maintained correctly , damage to the engine and cooling system may result . When the engine is cold, check the level of the engine coolant in the reservoir . • The engine coolant should b[...]

• DO NOT USE alcohol or methanol antifreeze or any engine coolants mixed with alcohol or methanol antifreeze. • DO NOT USE supplemental coolant additives in your vehicle. These additives may harm your engine’ s cooling system. • DO NOT MIX recycled coolant and conventional coolant together in your vehicle. Mixing of engine coolants may harm[...]

T o avoid scalding hot steam or coolant from being released from the engine cooling system, never remove the radiator cap while the engine is running or hot. Failure to follow this warning may result in damage to the engine’ s cooling system and possible severe personal injury . If you must remove the radiator cap, follow these steps to avoid per[...]

• NEVER increase the coolant concentration above 60%. • Increased engine coolant concentrations above 60% will decrease the freeze protection characteristics of the engine coolant and may cause engine damage. V ehicles driven year -round in non-extreme climates should use a 50/50 mixture of engine coolant and distilled water for optimum freeze [...]

properly , i.e., if the transaxle slips or shifts slowly or if you notice some sign of fluid leakage. Automatic transmission fluid expands when warmed. T o obtain an accurate fluid check, drive the vehicle until it is warmed up (approximately 30 km [20 miles]). If your vehicle has been operated for an extended period at high speeds, in city traffic[...]

High fluid level Fluid levels above the safe range may result in transaxle failure. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. High fluid levels can be caused by an overheating condition. Adjusting automatic transmission fluid levels Before adding any fluid, make sure the correct t[...]

CHANGING THE AIR FILTER ELEMENT 1. Release the four clamps that secure the air filter housing cover . 2. Carefully separate the two halves of the air filter housing. 3. Remove the air filter element from the air filter housing. 4. Install a new air filter element. Be careful not to crimp the filter element edges between the air filter housing and c[...]

If the electrolyte level in the battery is low , you can add plain tap water to the battery , as long as you do not use hard water (water with a high mineral or alkali content). If possible, however , try to only fill the battery cells with distilled water . If the battery needs water often, have the charging system checked. If your battery has a c[...]

transaxle must relearn its adaptive strategy . Optimal shifting will resume within a few hundred kilometers (miles) of operation. If the battery has been disconnected or a new battery has been installed, the clock and the preset radio stations must be reset once the battery is reconnected. • Always dispose of automotive batteries in a responsible[...]

The odor and particulate air filtration system is designed to reduce the concentration of objectionable exterior odors as well as airborne particles such as dust, spores and pollen in the air being supplied to the interior of the vehicle. The extent of EXTERIOR odor reduction depends on the odor itself and the perceptional threshold of the individu[...]

2. Remove the six (6) screws (B) from the cowl grille (A) at the base of the windshield. 3. Open the hood. 4. Remove the four (4) plastic screws (C) from the forward edge of the cowl leaf screen under the hood. • Remove the four (4) screw anchors by pushing upward on the screw anchor . 5. Disconnect the windshield washer hose at the Y connector a[...]

8. Remove four (4) screws from the top surface of the cabin air filter top cover . 9. Remove the cover . 10. Remove the filter element by pulling forward on the top surface of the filter and lifting. 11. Install the new filter (A) element into the filter retaining frame (B). Ensure that you insert the three retaining tabs in the bottom of the filte[...]

14. Position the cowl grille in place. 15. Reinstall the four (4) screw anchors and the four (4) plastic screws. 16. Close the hood. 17. Reinstall the six (6) screws in the cowl grille. 18. Reinstall the wiper arms. Ensure that you reinstall the wiper arms in the same position. 19. Push the wiper arm downward onto the wiper arm pivot until the smal[...]

INFORMA TION ABOUT TIRE QUALITY GRADES New vehicles are fitted with tires that have their T ire Quality Grade (described below) molded into the tire’ s sidewall. These T ire Quality Grades are determined by standards that the United States Department of T ransportation has set. T ire Quality Grades apply to new pneumatic tires for use on passenge[...]

T emperature A B C The temperature grades are A (the highest), B, and C, representing the tire’ s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire li[...]

• Four tire rotation Replacing the tires Replace the tires when the wear band is visible through the tire treads. When replacing full size tires, never mix radial bias-belted, or bias-type tires. Use only the tire sizes that are listed on the Certification Label. Make sure that all tires are the same size, speed rating, and load-carrying capacity[...]

Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier for the driver to lose control and roll over . T ires that are larger or smaller than your vehicle’ s original tires may also affect the accuracy of your speedometer . SNOW TIRES AND CHAINS Snow tires must be the same size and grade as the tire[...]

The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap. Otherwise, fuel may spray out and injure you or others. If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel sys[...]

• A void getting fuel liquid in your eyes. If fuel is splashed in the eyes, remove contact lenses (if worn), flush with water for 15 minutes and seek medical attention. Failure to seek proper medical attention could lead to permanent injury . • Fuels can also be harmful if absorbed through the skin. If fuel is splashed on the skin and/or clothi[...]

When the fuel filler door is open, the left hand sliding door will not open. When fueling your vehicle: 1. T urn the engine off. 2. Carefully turn the fuel filler cap counterclockwise, using caution to minimize the possibility of fuel spraying. 3. Remove the cap from the fuel filler pipe. 4. T o install the cap, turn it clockwise until you hear at [...]

Octane recommendations Y our vehicle is designed to use “Regular” unleaded gasoline with an (R+M)/2 octane rating of 87. W e do not recommend the use of gasolines labeled as “Regular” that are sold with octane ratings of 86 or lower in high altitude areas. Do not be concerned if your engine sometimes knocks lightly . However , if it knocks [...]

If you have run out of fuel: • Y ou may need to crank the engine several times after refueling before the system starts to pump the fuel from the tank to the engine. • Y our “Service Engine Soon” indicator may come on. For more information on the “Service Engine Soon” indicator , refer to the Instrumentation chapter . Fuel Filter For fu[...]

For consistent results when filling the fuel tank: • Use the same filling rate setting (low — medium — high) each time the tank is filled. • Allow three automatic click-offs when filling. • Always use fuel with the recommended octane rating. • Use a known quality gasoline, preferably a national brand. • Use the same side of the same p[...]

Habits • Smooth, moderate operation can yield up to 10% savings in fuel. • Steady speeds without stopping will usually give the best fuel economy . • Idling for long periods of time (greater than one minute) may waste fuel. • Anticipate stopping; slowing down may eliminate the need to stop. • Sudden or hard accelerations may reduce fuel e[...]

• Carrying unnecessary weight may reduce fuel economy (approximately 0.4 km/L [1 mpg] is lost for every 180 kg [400 lb] of weight carried). • Adding certain accessories to your vehicle (for example bug deflectors, rollover/light bars, running boards, ski/luggage racks) may reduce fuel economy . • Using fuel blended with alcohol may lower fuel[...]

The scheduled maintenance items listed in the Scheduled Maintenance Guide are essential to the life and performance of your vehicle and to its emissions system. If other than Ford, Motorcraft or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivale[...]

condition. T o ready the on-board diagnostics system for I/M testing, follow the procedure described below: 1. Allow the engine to cool to ambient temperature (the engine coolant temperature gauge indicator will point to C). 2. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indica[...]

Do not remove lamp bulbs unless they will be replaced immediately . If a bulb is removed for an extended period of time, contaminants may enter the lamp housings and affect performance. Replacing headlamp bulbs T o remove the headlamp bulb: 1. Make sure headlamp switch is in OFF position, then open the hood. 2. Disconnect the electrical connector f[...]

2. Install the bulb retaining ring over the plastic base until it contacts the rear of the socket by rotating clockwise until you feel a “stop.” 3. Connect the electrical connector into the rear of the plastic base until it snaps, locking it into position. 4. T urn the headlamps on and make sure they work properly . If the headlamp was correctl[...]

Replacing high-mount brakelamp bulbs 1. Remove the two screws and lamp assembly from vehicle. 2. Remove the bulb by rotating socket counterclockwise and pulling it out of the lamp assembly . 3. Pull bulb straight out of socket and push in the new bulb. 4. T o complete installation, follow removal procedure in the reverse order . Replacing tail lamp[...]

Replacing license plate lamp bulbs 1. Remove two screws, grommets and the license plate lamp assembly from the liftgate. 2. Remove bulb socket by turning counterclockwise. 3. Carefully pull the bulb from the socket and push in the new bulb. 4. Install the lamp assembly on liftgate with two grommets, ensuring the grommets are pushed all the way in t[...]

Function Number of bulbs T rade number Stepwell lamps 4 194 Glove compartment 1 194 All replacement bulbs are clear in color except where noted. T o replace all instrument panel lights - see your dealer . AIMING THE HEADLAMPS The alignment of your headlamps should be checked by a qualified service technician if: • Oncoming motorists frequently si[...]

Remove any exterior accessories, such as antennas, before entering a car wash. If you have wax applied to the vehicle at a commercial car wash, it is recommended that you clean the wiper blades and windshield as described in Cleaning the wiper blades and windshield. After washing, apply the brakes several times to dry them. W axing your vehicle W a[...]

Cleaning the engine Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal. When washing: • T ake care when using a power washer to clean the engine. The high pressure fluid could penetrate the sealed parts and cause damage. • Do not spray with cold water to avoid cracking the engine bl[...]

Cleaning the exterior lamps W ash with the same detergent as the exterior of your vehicle. If necessary , use a tar remover such as Ford Extra Strength T ar and Road Oil Remover (B7A-19520–AA) or tar remover if necessary . T o avoid scratching the lamps, do not use a dry paper towel, chemical solvents or abrasive cleaners. Cleaning the wiper blad[...]

Cleaning the built-in child seat (if equipped) Clean with mild soap and water . Do not use household cleaning products because they may weaken the safety belt webbing or damage the vinyl parts of the seat. The child seat liner is removable and may be machine-washed and air dried. Cleaning the interior fabric Remove dust and loose dirt with a whisk [...]

MOTORCRAFT PART NUMBERS Component 3.3L V6 engine Engine air filter element F A-1121 Cabin air filter FP-27 Fuel filter FG-993 Battery (standard) BXT -35 Battery 1 BXT -24F Oil filter FL-2007 PCV V alve EV -217 Spark plugs 2 AGSP-32FP 1 Standard for Canada. Included with trailer tow package and rear A/C. 2 Refer to V ehicle Emissions Control Informa[...]

LUBRICANT SPECIFICATIONS Item Ford part name Ford part number Ford specification Brake fluid High Performance DOT 3 Motor V ehicle Brake Fluid C6AZ-19542-AB ESA-M6C25-A and DOT 3 Door weatherstrips Silicone Lubricant F7AZ-19G208-BA and F5AZ-19553-AA ESR-M13P4-A Engine coolant Ford Premium Engine Coolant E2FZ-19549-AA (in Canada, Motorcraft CXC-8-B)[...]

Item Ford part name Ford part number Ford specification Disc brake caliper rails Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A (Motorcraft W A-10) ESE-M1C171-A Constant velocity joints CV Joint Grease (High T emp.) E43Z-19590-A ESP-M1C207-A W indshield washer fluid Ultra-clear W indshield W asher Concentrate C9AZ-19550-AC ESR-[...]

VEHICLE DIMENSIONS V ehicle dimensions mm (in) (1) Overall length 4 945.4 (194.7) (2) Overall width 1 902.5 (74.9) (3) Overall height (with luggage rack) 1 780.5 (70.1) (4) Wheelbase 2 849.9 (112.2) (5) T rack - Front 1 610.4 (63.4) (5) T rack - Rear 1 610.4 (63.4) 2 5 3 Capacities and specifications 238[...]

IDENTIFYING YOUR VEHICLE Certification label The National Highway T raffic Safety Administration Regulations require that a Certification Label be affixed to a vehicle and prescribe where the Certification Label may be located. The Certification Label is located on the front door latch pillar on the driver’ s side. 1 4 MFD . BY FORD MOT OR CO. DA[...]

V ehicle identification number The vehicle identification number is attached to a metal tag and is located on the driver side instrument panel and under the liftgate scuff plate at the bottom of the liftgate opening. (Please note that in the graphic XXXX is representative of your vehicle identification number .) Engine and transmission serial numbe[...]

GETTING ROADSIDE ASSIST ANCE T o fully assist you should you have a vehicle concern, Ford offers a complimentary roadside assistance program. This program is separate from the New V ehicle Limited W arranty . The service is available: • 24–hours, seven days a week • for the Basic warranty period (Canada) or New V ehicle Limited W arranty peri[...]

Ford Extended Service Plan Y ou can get more protection for your new car or light truck by purchasing Ford Extended Service Plan (Ford ESP) coverage. Ford ESP is an optional service contract which is backed by Ford Motor Company or Ford Motor Service Company (in the U.S.) and Ford of Canada (in Canada). It provides the following: • Protection aga[...]

Getting the service you need At home Ford Motor Company and Ford of Canada have authorized dealerships to service your vehicle. When you need warranty repairs your selling dealer would like you to return to it for that service, but you may also take your vehicle to another Ford Motor Company dealership authorized for warranty repairs. Certain warra[...]

If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Assistance Center to find an authorized dealership to help you. In the United States: Ford Motor Company Customer Assistance Center 1680[...]

THE DISPUTE SETTLEMENT BOARD (U.S. only) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes • available free to owners and lessees of qualifying Ford Motor Company vehicles The Dispute Settlement Board may not be available in all states. Ford Motor Company reserves the right to change eligib[...]

Board membership The Board consists of: • three consumer representatives • a Ford or Lincoln-Mercury dealership representative Consumer candidates for Board membership are recruited and trained by an independent consulting firm. The dealership Board member is chosen from Ford and Lincoln-Mercury dealership management, recognized for their busin[...]

Y ou will receive a letter of explanation if your application does not qualify for Board review . Oral presentations If you would like to make an oral presentation, indicate YES to question #6 on the application. While it is your right to make an oral presentation before the Board, this is not a requirement and the Board will decide the case whethe[...]

GETTING ASSIST ANCE OUTSIDE THE U.S. AND CANADA Before exporting your vehicle to a foreign country , contact the appropriate foreign embassy or consulate. These officials can inform you of local vehicle registration regulations and where to find unleaded fuel. If you cannot find unleaded fuel or can only get fuel with an anti-knock index lower than[...]

Ford Custom Silicone Gloss Polish Ford Custom Vinyl Protectant* Ford Deluxe Leather and Vinyl Cleaner Ford Extra Strength T ar and Road Oil Remover* Ford Extra Strength Upholstery Cleaner Ford Metal Surface Cleaner Ford Multi-Purpose Cleaner* Motorcraft Car W ash Concentrate Motorcraft Carlite Glass Cleaner Ford Spot and Stain Remover* Ford Super P[...]

Comfort and convenience Air conditioner Air filtration systems Cargo nets Cargo organizers Cargo shades Cargo trays Dash trim Engine block heaters Gear shift knob Luggage presenter (Continental only) Manual sliding rear window T ire step T ravel equipment Console Console armrest Daytime running lights Factory luggage rack Factory luggage rack adapt[...]

Soft luggage cover Speed control T owing mirrors T railer hitch T railer hitch bars and balls T railer hitch wiring adaptor Protection and appearance equipment Air bag anti-theft locks Bed mat/bedliner tailgate covers Bed mats Bedliners Car/truck covers Cargo liners, interior Carpet floor mats Cleaners, waxes and polishes Flat splash guards Front e[...]

T ailgate lock T ailgate protector T onneau covers T ouch-up paint Universal floor mats For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to your vehicle, do not exceed the total weight capacity of the vehicle o[...]

ORDERING ADDITIONAL OWNER’S LITERA TURE T o order the publications in this portfolio in the United States: Make checks payable to: HELM, INCORPORA TED P .O. Box 07150 Detroit, Michigan 48207 For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.m. - 6:00 p.m. EST , for credit card holders only T o order the publicat[...]

REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway T raffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company . If NHTSA receives similar complaints, it may open an investigation, and i[...]

Accessory delay .......................... 90 Air bag supplemental restraint system ........................................ 131 and child safety seats ............ 133 description .............................. 131 disposal .................................... 135 driver air bag .......................... 133 indicator light ......................[...]

Ford accessories for your vehicle ..................................... 248 Ford Extended Service Plan .......................................... 242 Getting assistance outside the U.S. and Canada ..................... 248 Getting roadside assistance ................................ 241 Getting the service you need .................................[...]

GVWR (Gross V ehicle W eight Rating) ....................................... 165 calculating ............................... 165 definition ................................. 165 driving with a heavy load ...... 165 location .................................... 165 Hazard flashers ......................... 171 Head restraints .......................[...]

Overdrive ..............................87,164 Panic alarm feature, remote entry system .............................. 101 Parking brake ............................ 158 Parts (see Motorcraft parts) ....235 Power distribution box (see Fuses) ...............................176 Power door locks ........................ 90 Power steering .............[...]

W arning chimes ...................... 10,11 W arning lights (see Lights) ......... 6 W asher fluid ..............................198 W ater , Driving through ............. 164 W indows power ......................................... 89 rear wiper/washer ..................... 87 W indshield washer fluid and wipers ..................................[...]

260[...]

261[...]

262[...]

263[...]

Item Information Required fuel Unleaded fuel only - 87 octane Fuel tank capacity 75.7L (20.0 gallons) Engine oil capacity (includes filter change) 4.0L (4.2 quarts). Use Motorcraft SAE 5W -30 Super Premium Motor Oil, Ford specification WSS-M2C153-G. T ire size and pressure Refer to the Certification Label on inside of driver’ s door . Hood releas[...]