Nissan 2009 Altima manual

200 9 N I S S AN AL TI MA 200 9 AL TI MA OWN E R'S MAN UAL L3 2-D Printing : Mar ch 2009 ( 1 0) Publication No.: OM9E-0L3 2U2 Printed in U.S.A. F or your saf et y , r ead carefully and k eep in this v ehicle. L3 2-D[...]

W elcome to the growing family of new NISSAN owners. This vehicle is delivered to you with confidence. It was produced using the latest techniques and strict quality control. This manual was prepared to help you under- stand the operation and maintenance of your vehicle so that you may enjoy many miles (kilome- ters) of driving pleasure. Please rea[...]

This manual includes information for all options available on this model. Therefore, you may find some information that does not apply to your vehicle. All information, specifications and illustrations in this manual are those in effect at the time of printing. NISSAN reserves the right to change specifications or design without notice and with- ou[...]

BLUETOOTH t is a trademark owned by Bluetooth SIG, Inc., U.S.A. and licensed to Visteon and Xanavi Informatics Corporation. XM Radio t requires subscription, sold separately after first 90 days. Not available in Alaska, Hawaii or Guam. For more information, visit www.xmradio.com. © 2009 NISSAN NORTH AMERICA , INC. All rights reserved. No part of t[...]

NISSAN CARE S... Both NISSAN and your NISSAN dealer are dedicated to serving all your automotive needs. Y our satisfaction with your vehicle and your NISSAN dealer are our primary concerns. Y our NISSAN dealer is always available to assist you with all your automobile sales and service needs. However, if there is something that your NISSAN dealer c[...]

T able of Contents Illustrated table of contents Safety—Seats, seat belts and supplemental restraint system Instruments and controls Pre-driving checks and adjustments Monitor, climate, audio, phone and voice recognition systems Starting and driving In case of emergency Appearance and care Maintenance and do-it-yourself T echnical and consumer in[...]

0 Illustrated table of contents Air bags, seat belts and child restraints ..............0 - 2 Exterior front ......................................0 - 3 Exterior rear .......................................0 - 5 Passenger compartment ...........................0 - 7 Instrument panel ...................................0 - 8 Engine compartment check [...]

1. T op tether strap anchor (P . 1-27) 2. Rear seat belts (P . 1-15) 3. Roof-mounted curtain side-impact supplemental air bag (P . 1-43) 4. Front seat-mounted side-impact supplemental air bag (P . 1-43) 5. Head Restraints (P . 1-11 ) 6. Front seat belts (P . 1-15) 7. Supplemental front-impact air bags (P . 1-43) 8. Seats (P . 1-2) 9. Occupant class[...]

Coupe 1. P ower windows (P . 2-44) 2. Windshield (P . 8-20) 3. Windshield wiper and washer switch (P . 2-27) 4. Engine hood (P . 3-23) 5. Tie down/towing hooks (if so equipped) (P . 6-12) 6. Fog light switch (if so equipped) (P . 2-33) 7. Headlight and turn signal switch (P . 2-29) 8. Replacing bulbs (P . 8-27) 9. Tire pressure (P . 8-34) 10. Flat [...]

Sedan 1. P ower windows (P . 2-44) 2. Windshield (P . 8-20) 3. Windshield wiper and washer switch (P . 2-27) 4. Engine hood (P . 3-23) 5. Tie down/towing hooks (if so equipped) (P . 6-12) 6. Fog light switch (if so equipped) (P . 2-33) 7. Headlight and turn signal switch (P . 2-29) 8. Replacing bulbs (P . 8-27) 9. Tire pressure (P . 8-34) 10. Flat [...]

Coupe 1. Rear window defroster switch (P . 2-28) 2. Interior trunk lid release (P . 3-24) 3. T runk lid (P . 3-23) 4. V ehicle loading (P . 9-12) 5. Opener operation (if so equipped) (P . 3-23) 6. Replacing bulbs (P . 8-27) 7. Fuel-filler cap, fuel recommendation (P . 3-25, P . 9-3) 8. Fuel-filler door (P . 3-25) WII0125 EXTERIOR REAR Illustrated t[...]

Sedan 1. Rear window defroster switch (P . 2-28) 2. Interior trunk lid release (P . 3-24) 3. T runk lid (P . 3-23) 4. V ehicle loading (P . 9-12) 5. Opener operation (if so equipped) (P . 3-23) 6. Replacing bulbs (P . 8-27) 7. Fuel-filler cap, fuel recommendation (P . 3-25, P . 9-3) 8. Fuel-filler door (P . 3-25) 9. Child safety rear door lock (P .[...]

1. Interior trunk access (P . 1-9) 2. Moonroof (if so equipped) (P . 2-46) 3. Sun visors (P . 3-27) 4. Interior lights, illuminated entry (P . 2-48) 5. HomeLink T (if so equipped) (P . 2-51) 6. Automatic anti-glare inside mirror (if so equipped) (P . 3-28) 7. Glove box (P . 2-41) 8. Front cup holders (P . 2-40) 9. Front console (P . 2-41) 10. Front[...]

1. V ents (P . 4-10) 2. Headlight/fog light (if so equipped)/turn signal switch (P . 2-29) 3. Steering wheel switch for audio control (if so equipped)/Bluetooth T hands-free phone system (if so equipped) (P . 4-44, P . 4-46, P . 4-61) 4. Meters and gauges (P . 2-3) 5. Driver supplemental air bag/horn (P . 1-43, P . 2-34) 6. Cruise control main/set [...]

20. T raction Control System (T CS) OFF switch (if so equipped) (P . 5-25) T runk opener (P . 3-23) V ehicle Dynamic Control (VDC) OFF switch (if so equipped) (P . 2-35) Intelligent K ey port (P . 5-7) *: Refer to the separate Navigation System Own- er’s Manual. See the page number indicated in paren- theses for operating details. Illustrated tab[...]

QR25DE engine 1. P ower steering fluid reservoir (P . 8-13) 2. Engine oil filler cap (P . 8-9) 3. Brake fluid reservoir/Clutch fluid reservoir (M/T model) (P . 8-14, 8-14) 4. Air cleaner (P . 8-19) 5. Fuse block (P . 8-22) 6. Battery (P . 8-15) 7. Fuse/fusible link box (P . 8-22) 8. Engine oil dipstick (P . 8-9) 9. Radiator cap (P . 8-8) 10. Drive [...]

VQ35DE engine 1. P ower steering fluid reservoir (P . 8-13) 2. Engine oil filler cap (P . 8-9) 3. Brake fluid reservoir/Clutch fluid reservoir (M/T model) (P . 8-14, 8-14) 4. Air cleaner (P . 8-19) 5. Fuse block (P . 8-22) 6. Battery (P . 8-15) 7. Fuse/fusible link box (P . 8-22) 8. Engine oil dipstick (P . 8-9) 9. Radiator cap (P . 8-8) 10. Drive [...]

W arning light Name Page or Anti-lock Braking System (ABS) warn- ing light 2-11 or Brake warning light 2-11 Charge warning light 2-11 Continuously V ari- able T ransmission (CVT) check warn- ing light (if so equipped) 2-11 Engine oil pressure warning light 2-12 Low tire pressure warning light 2-12 W arning light Name Page Master warning light 2-13 [...]

1 Safety—Seats, seat belts and supplemental restraint system Seats ............................................1 - 2 Front manual seat adjustment ....................1 - 2 Front power seat adjustment (if so equipped for driver’s seat) ..................1 - 4 Folding rear seat ...............................1 - 9 Head restraints ................[...]

WARNING ● Do not ride in a moving vehicle when the seatback is reclined. This can be dangerous. The shoulder belt will not be against your body. In an accident, you could be thrown into it and receive neck or other serious injuries. Y ou could also slide under the lap belt and receive serious internal injuries. ● For the most effective protecti[...]

Forward and backward Pull the center of the bar up and hold it while you slide the seat forward or backward to the desired position. Release the bar to lock the seat in position. Reclining T o recline the seatback, pull the lever up and lean back. T o bring the seatback forward, pull the lever up and lean your body forward. Release the lever to loc[...]

FRONT POWER SEAT ADJUSTMENT (if so equipped for driver’s seat) Operating tips ● The power seat motor has an auto-reset overload protection circuit. If the motor stops during operation, wait 30 seconds, then reactivate the switch. ● Do not operate the power seat switch for a long period of time when the engine is off. This will discharge the b[...]

CAUTION ● Do not operate the power recline switch when the seatback has been manually released using the upper seatback re- lease lever s 1 . Doing so can damage the seat. ● Do not pull on the upper seatback re- lease lever or the trim to return the seatback to a normal seating position. Doing so may damage the seat. Forward and backward Moving[...]

Seat lifter (if so equipped for driver’s seat) Pull the lever up or push down to adjust the angle and height of the seat cushion. Lumbar support (if so equipped for driver’s seat) The lumbar support feature provides lower back support to the driver. Push the switch (T ype A) forward or backward or move the lever (T ype B) up or down to adjust t[...]

Entry to the rear seat from outside of the vehicle on the front passenger side (Coupe) Pull the seat recliner lever s 1 to the uppermost position folding the seatback forward s 2 , releas- ing the seat track. Slide the entire seat forward for access to the rear seat. T o return the seat to a locked position: Push the upper seatback rearward until t[...]

Pull the upper seatback release lever s 1 to the uppermost position, folding the seatback forward s 2 , releasing the seat track. Slide the entire seat forward for access to the rear seat. T o return the seat to a locked position: Push the upper seatback rearward until the seat- back and track are locked. Operating tips: ● The seatback and track [...]

Exiting from the rear seat on the driver’s side, using the upper seatback release lever (coupe) Pull the upper seatback release lever s 1 to the uppermost position, folding the seatback forward s 2 , releasing the seat track. Slide the entire seat forward to exit from the rear seat. T o return the seat to a locked position: Push the upper seatbac[...]

1. Open the access cover on the rear parcel shelf. 2. Push down on the button on the rear parcel shelf. 3. Fold down the passenger’s side seatback. WARNING ● Never allow anyone to ride in the cargo area or on the rear seat when it is in the fold-down position. Use of these areas by passengers without proper restraints could result in serious in[...]

Center armrest (if so equipped) Pull the armrest down until it is horizontal. HEAD RESTRAINTS WARNING Head restraints supplement the other ve- hicle safety systems. They may provide additional protection against injury in cer- tain rear end collisions. Adjust the head restraints properly, as specified in this section. Check the adjustment after som[...]

Components 1. Head restraint 2. Adjustment notches 3. Lock knob 4. Stalks Adjustment Adjust the head restraint so the center is level with the center of the seat occupant’s ears. T o raise the head restraint, pull it up. LRS0887 WRS0134 LRS0888 1-12 Safety—Seats, seat belts and supplemental restraint system Z REVIEW COPY— 2009 Altima (alt) Ow[...]

T o lower, push and hold the lock knob and push the head restraint down. Removal Use the following procedure to remove the ad- justable head restraints. 1. Pull the head restraint up to the highest position. 2. Push and hold the lock knob. 3. Remove the head restraint from the seat. 4. Store the head restraint properly so it is not loose in the veh[...]

Front-seat Active Head Restraints The Active Head Restraint moves forward utiliz- ing the force that the seatback receives from the occupant in a rear-end collision. The movement of the head restraint helps support the occu- pant’s head by reducing its backward movement and helping absorb some of the forces that may lead to whiplash-type injuries[...]

PRECAUTIONS ON SEAT BELT USAGE If you are wearing your seat belt properly ad- justed and you are sitting upright and well back in your seat with both feet on the floor, your chances of being injured or killed in an accident and/or the severity of injury may be greatly reduced. NISSAN strongly encourages you and all of your passengers to buckle up e[...]

WARNING ● Every person who drives or rides in this vehicle should use a seat belt at all times. Children should be properly re- strained in the rear seat and, if appro- priate, in a child restraint. WARNING ● The seat belt should be properly ad- justed to a snug fit. Failure to do so may reduce the effectiveness of the entire restraint system a[...]

WARNING ● Always route the shoulder belt over your shoulder and across your chest. Never put the belt behind your back, under your arm or across your neck. The belt should be away from your face and neck, but not falling off your shoulder. ● Position the lap belt as low and snug as possible AROUND THE HIPS, NO T THE WAIST . A lap belt worn too [...]

CHILD SAFETY Children need adults to help protect them. They need to be properly restrained. In addition to the general information in this manual, child safety information is available from many other sources, including doctors, teachers, government traffic safety offices, and community organizations. Every child is different, so be sure to learn [...]

80 lbs (36 kg) . A booster seat should be used to obtain proper seat belt fit. NISSAN recommends that a child be placed in a commercially available booster seat if the shoul- der belt in the child’s seating position fits close to the face or neck or if the lap portion of the seat belt goes across the abdomen. The booster seat should raise the chi[...]

Fastening the seat belts 1. Adjust the seat. See “Seats” earlier in this section. s 2 Slowly pull the seat belt out of the retractor and insert the tongue into the buckle until you hear and feel the latch engage. ● The retractor is designed to lock during a sudden stop or on impact. A slow pulling motion permits the seat belt to move, and all[...]

The Emergency Locking Retractor (ELR) mode allows the seat belt to extend and retract to allow the driver and passengers some freedom of movement in the seat. The ELR locks the seat belt when the vehicle slows down rapidly or during certain impacts. The Automatic Locking Retractor (ALR) mode (child restraint mode) locks the seat belt for child rest[...]

Shoulder belt height adjustment (Sedan, front seats) The shoulder belt anchor height should be ad- justed to the position best for you. (See “Precau- tions on seat belt usage” earlier in this section.) T o adjust, pull out the adjustment button s 1 and move the shoulder belt anchor to the desired position s 2 , so the belt passes over the cente[...]

WARNING ● Only NISSAN seat belt extenders, made by the same company which made the original equipment seat belts, should be used with NISSAN seat belts. ● Adults and children who can use the standard seat belt should not use an extender. Such unnecessary use could result in serious personal injury in the event of an accident. ● Never use seat[...]

WARNING ● Infants and small children should al- ways be placed in an appropriate child restraint while riding in the vehicle. Failure to use a child restraint can re- sult in serious injury or death. ● Infants and small children should never be carried on your lap. It is not possible for even the strongest adult to resist the forces of a severe[...]

● When your child restraint is not in use, keep it secured with the LA TCH system or a seat belt to prevent it from being thrown around in case of a sudden stop or accident. CAUTION Remember that a child restraint left in a closed vehicle can become very hot. Check the seating surface and buckles before placing your child in the child restraint. [...]

LA T CH lower anchor point locations The LA T CH anchors are located at the rear of the seat cushion near the seatback. A label is at- tached to the seatback to help you locate the LA T CH anchors. WARNING ● Attach LA TCH system compatible child restraints only at the locations shown. If a child restraint is not secured properly, your child could[...]

LA T CH child restraints generally require the use of a top tether strap. See “T op tether strap child restraint” later in this section for installation in- structions. When installing a child restraint, carefully read and follow the instructions in this manual and those supplied with the child restraint. See “Child restraint installation usi[...]

First, secure the child restraint with the LA T CH System (rear outboard seating positions only) or the seat belt, as applicable. s 1 Flip up the anchor cover from the anchor point which is located directly behind the child seat. s 2 P osition the top tether strap over the top of the seatback. s 3 Secure the tether strap to the tether anchor bracke[...]

1. If the rear seat cushion has a flap s 1 , pull the flap down to allow access to the anchors s 2 . 2. P osition the child restraint on the seat. Al- ways follow the child restraint manufactur- er’s instructions. 3. Secure the child restraint anchor attach- ments to the LA T CH lower anchors. Check to make sure the LA T CH attachment is prop- er[...]

5. For child restraints that are equipped with webbing mounted attachments, remove any additional slack from the anchor attach- ments. Press downward and rearward firmly in the center of the child restraint with your knee to compress the vehicle seat cushion and seatback while tightening the webbing of the anchor attachments. 6. If the child restra[...]

1. If the rear seat cushion has a flap s 1 , pull the flap down to allow access to the anchors s 2 . 2. P osition the child restraint on the seat. Al- ways follow the child restraint manufactur- er’s instructions. Check to make sure the LA T CH attachment is properly attached to the lower anchors. 3. Secure the child restraint anchor attach- ment[...]

4. For child restraints that are equipped with webbing mounted attachments, remove any additional slack from the anchor attach- ments. Press downward and rearward firmly in the center of the child restraint with your hand to compress the vehicle seat cushion and seatback while tightening the webbing of the anchor attachments. 5. After attaching the[...]

CHILD RESTRAINT INSTALLATION USING THE SEAT BELTS WARNING ● Even with the NISSAN Advanced Air Bag System, never install a rear-facing child restraint in the front passenger seat. Front air bags inflate with great force. A rear-facing child restraint could be struck by the front air bag in a crash and could seriously injure or kill your child. ●[...]

2. P osition the child restraint on the seat. Al- ways follow the child restraint manufactur- er’s instructions. The back of the child restraint should be secured against the vehicle seatback. If necessary , adjust or remove the head restraint to obtain the correct child restraint fit. See “Head restraint adjustment” in this section. If the h[...]

5. Allow the seat belt to retract. Pull up on the shoulder belt to remove any slack in the belt. 6. Remove any additional slack from the seat belt; press downward and rearward firmly in the center of the child restraint with your knee to compress the vehicle seat cushion and seatback while pulling up on the seat belt. 7. If the child restraint is e[...]

the belt holds the restraint in place. If the restraint is not secure, tighten the belt as necessary , or put the restraint in another seat and test it again. Y ou may need to try a different child restraint. Not all child re- straints fit in all types of vehicles. 9. Check that the retractor is in the ALR mode by trying to pull more seat belt out [...]

2. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manufacturer’s in- structions for belt routing. 3. Pull the shoulder belt until the belt is fully extended. At this time, the seat belt retractor is in the Automatic Locking Retrac[...]

5. Remove any additional slack from the child restraint; press downward and rearward firmly in the center of the child restraint to compress the vehicle seat cushion and seat- back while pulling up on the seat belt. 6. After attaching the child restraint, test it be- fore you place the child in it. Push it from side to side while holding the seat n[...]

PRECAUTIONS ON BOOSTER SEATS WARNING ● Infants and small children should al- ways be placed in an appropriate child restraint while riding in the vehicle. Failure to use a child restraint or booster seat can result in serious injury or death. ● Infants and small children should never be carried on your lap. It is not possible for even the stron[...]

● After placing the child in the booster seat and fastening the seat belt, make sure the shoulder portion of the belt is away from the child’s face and neck and the lap portion of the belt does not cross the abdomen. ● Do not put the shoulder belt behind the child or under the child’s arm. If you must install a booster seat in the front sea[...]

All U.S. states and Canadian provinces or territories require that infants and small children be restrained in an approved child restraint at all times while the vehicle is being operated. The instructions in this section apply to booster seat installation in the rear seats or the front passenger seat. BOOSTER SEAT INSTALLATION WARNING NISSAN recom[...]

3. The booster seat should be positioned on the vehicle seat so that it is stable. If neces- sary , adjust or remove the head restraint to obtain the correct booster seat fit. See “Head restraint adjustment” earlier in this section. If the head restraint is removed, store it in a secure place. Be sure to reinstall the head restraint when the bo[...]

6. Follow the warnings, cautions and instruc- tions for properly fastening a seat belt shown in “Three-point seat belt with retrac- tor” earlier in this section. 7. If the booster seat is installed in the front passenger seat, push the ignition switch to the ON position. The front passenger air bag status light may or may not illuminate, depend[...]

Roof-mounted curtain side-impact supple- mental air bag system: This system can help cushion the impact force to the head of occu- pants in front and rear outboard seating positions in certain side-impact collisions. The curtain air bags are designed to inflate on the side where the vehicle is impacted. These supplemental restraint systems are de- [...]

● The driver and front passenger seat belt buckles are equipped with sensors that detect if the seat belts are fastened. The Advanced Air Bag System monitors the severity of a collision and seat belt us- age then inflates the air bags. Failure to properly wear seat belts can increase the risk or severity of injury in an accident. ● The front pa[...]

WARNING ● Never let children ride unrestrained or extend their hands or face out of the window. Do not attempt to hold them in your lap or arms. Some examples of dangerous riding positions are shown in the illustrations. ARS1041 ARS1042 ARS1043 1-46 Safety—Seats, seat belts and supplemental restraint system Z REVIEW COPY— 2009 Altima (alt) Ow[...]

WARNING ● Children may be severely injured or killed when the front air bags, side air bags or curtain air bags inflate if they are not properly restrained. Pre-teens and children should be properly re- strained in the rear seat, if possible. ● Even with the NISSAN Advanced Air Bag System, never install a rear-facing child restraint in the fron[...]

WARNING Front seat-mounted side-impact supple- mental air bags and roof-mounted curtain side-impact supplemental air bags: ● The side air bags and curtain air bags ordinarily will not inflate in the event of a frontal impact, rear impact, rollover or lower severity side collision. Always wear your seat belts to help reduce the risk or severity of[...]

SSS0159 SSS0162 Safety—Seats, seat belts and supplemental restraint system 1-49 Z REVIEW COPY— 2009 Altima (alt) Owners Manual (owners) —USA_English (nna) 02/03/09—debbie X[...]

Coupe WRS0845 1-50 Safety—Seats, seat belts and supplemental restraint system Z REVIEW COPY— 2009 Altima (alt) Owners Manual (owners) —USA_English (nna) 02/03/09—debbie X[...]

1. Roof-mounted curtain side-impact supplemental air bag inflators 2. Roof-mounted curtain side-impact supplemental air bags 3. Front seat-mounted side-impact supplemental air bag modules 4. Air bag Control Unit (ACU) 5. Supplemental front-impact air bag mod- ules 6. Crash zone sensor 7. Seat belt buckle switches on driver’s and passenger’s sid[...]

NISSAN Advanced Air Bag System (front seats) This vehicle is equipped with the NISSAN Ad- vanced Air Bag System for the driver and front passenger seats. This system is designed to meet certification requirements under U.S. regu- lations. It is also permitted in Canada. However, all of the information, cautions and warn- ings in this manual still a[...]

Front passenger air bag and status light WARNING The front passenger air bag is designed to automatically turn OFF under some con- ditions. Read this section carefully to learn how it operates. Proper use of the seat, seat belt and child restraints is nec- essary for most effective protection. Fail- ure to follow all instructions in this manual con[...]

NISSAN recommends that pre-teens and chil- dren be properly restrained in a rear seat. NISSAN also recommends that appropriate child restraints and booster seats be properly installed in a rear seat. If this is not possible, the occupant classification sensor is designed to operate as described above to turn the front passenger air bag OFF for spec[...]

● Do not place objects with sharp edges on the seat. Also, do not place heavy objects on the seat that will leave per- manent impressions in the seat. Such objects can damage the seat or occu- pant classification sensor (pattern sen- sor) . This can affect the operation of the air bag system and result in serious personal injury. ● Do not use w[...]

Front seat-mounted side-impact supplemental air bag and roof- mounted curtain side-impact supplemental air bag systems The side air bags are located in the outside of the seatback of the front seats. The curtain air bags are located in the side roof rails. These systems are designed to meet voluntary guidelines to help reduce the risk of injury to [...]

● Right after inflation, several side air bag and curtain air bag system components will be hot. Do not touch them; you may severely burn yourself. ● No unauthorized changes should be made to any components or wiring of the side air bag and curtain air bag systems. This is to prevent damage to or accidental inflation of the side air bag and cur[...]

When a pretensioner activates, smoke is re- leased and a loud noise may be heard. This smoke is not harmful and does not indicate a fire. Care should be taken not to inhale it, as it may cause irritation and choking. Those with a history of a breathing condition should get fresh air promptly . After pretensioner activation, load limiters allow the [...]

When the ignition is placed in the ON position, the supplemental air bag warning light illuminates for about 7 seconds and then turns off. This means the system is operational. If any of the following conditions occur, the front air bag, side air bag and curtain air bag and pretensioner systems need servicing: ● The supplemental air bag warning l[...]

2 Instruments and controls Instrument panel ...................................2 - 2 Meters and gauges ................................2 - 3 Speedometer and Odometer ....................2 - 4 T achometer ....................................2 - 5 Engine coolant temperature gauge ...............2 - 5 Fuel gauge ....................................2 -[...]

Covered storage box ........................... 2-42 Grocery hooks (if so equipped) ................. 2-43 Cargo net (if so equipped) ...................... 2-43 Windows ........................................ 2-44 P ower windows ............................... 2-44 Moonroof (if so equipped) ......................... 2-46 Automatic moonroof ......[...]

1. V ents (P . 4-10) 2. Headlight/fog light (if so equipped)/turn signal switch (P . 2-29) 3. Steering wheel switch for audio control (if so equipped)/Bluetooth T hands-free phone system (if so equipped) (P . 4-44, P . 4-46, P . 4-61) 4. Meters and gauges (P . 2-3) 5. Driver supplemental air bag/horn (P . 1-43, P . 2-34) 6. Cruise control main/set [...]

20. T raction Control System (T CS) OFF switch (if so equipped) (P . 5-25) T runk opener (P . 3-23) V ehicle Dynamic Control (VDC) OFF switch (if so equipped) (P . 2-35) Intelligent K ey port (P . 5-7) *: Refer to the separate Navigation System Own- er’s Manual. See the page number indicated in paren- theses for operating details. 1. T achometer [...]

1. Speedometer 2. Change button 3. Odometer/twin trip odometer SPEEDOMETER AND ODOMETER Speedometer The speedometer s 1 indicates vehicle speed in miles per hour (MPH) and kilometers per hour (km/h) . Odometer/T win trip odometer The odometer/twin trip odometer is displayed when the ignition switch is placed in the ON position. The odometer records[...]

T ACHOMETER The tachometer indicates engine speed in revo- lutions per minute (rpm) . Do not rev engine into the red zone s 1 . CAUTION When engine speed approaches the red zone, shift to a higher gear or reduce en- gine speed. Operating the engine in the red zone may cause serious engine damage. ENGINE COOLANT TEMPERATURE GAUGE The gauge indicates[...]

FUEL GAUGE The gauge indicates the approximate fuel level in the tank. The gauge may move slightly during braking, turning, acceleration, or going up or down hills. The gauge needle returns to E (Empty) after the ignition switch is placed in the OFF position. The low fuel warning light comes on when the amount of fuel in the tank is getting low . R[...]

Push the button for about 1 second when the ignition switch is placed in the ON position to toggle the compass display s 1 on or off. The display will indicate the direction of the vehicle’s heading. N: North E: East S: South W: W est If the display reads “C” , calibrate the compass by driving the vehicle in three complete circles at less tha[...]

● If a magnet is located near the com- pass or the vehicle is driven where the terrestrial magnetism is disturbed, the compass display may not indicate the correct direction. ● In places where the terrestrial magne- tism is disturbed, the correction of the direction starts automatically. Inaccurate compass direction: The compass display is equi[...]

● The compass may not indicate the correct compass point in tunnels or while driving up or down a steep hill. (The compass returns to the correct compass point when the ve- hicle moves to an area where the geomag- netism is stabilized.) CAUTION ● Do not install a ski rack, antenna, etc ., which are attached to the vehicle by means of a magnet. [...]

or Anti-lock Braking System (ABS) warning light NISSAN Intelligent Key™ warning light Security indicator light or Brake warning light Seat belt warning light and chime Slip indicator light (if so equipped) Charge warning light Supplemental air bag warning light T raction Control System off indicator light (if so equipped) Continuously V ariable T[...]

W ARNING LIGHTS or Anti-lock Braking System (ABS) warning light When the ignition switch is placed in the ON position, the Anti-lock Braking System (ABS) warning light illuminates and then turns off. This indicates the ABS is operational. If the ABS warning light illuminates while the engine is running, or while driving, it may indicate the ABS is [...]

Engine oil pressure warning light This light warns of low engine oil pressure. If the light flickers or comes on during normal driving, pull off the road in a safe area, stop the engine immediately and call a NISSAN dealer or other authorized repair shop. The engine oil pressure warning light is not designed to indicate a low oil level. Use the dip[...]

● If the light illuminates while driving, avoid sudden steering maneuvers or abrupt braking, reduce vehicle speed, pull off the road to a safe location and stop the vehicle as soon as possible. Driving with under-inflated tires may permanently damage the tires and in- crease the likelihood of tire failure. Se- rious vehicle damage could occur and[...]

The seat belt warning light may also illuminate if the front passenger’s seat belt is not fastened when the front passenger’s seat is occupied. For 7 seconds after the ignition switch is placed in the ON position, the system does not activate the warning light for the front passenger. Refer to “Seat belts” in the “Safety—Seats, seat bel[...]

The Malfunction Indicator Light may also come on steady if the fuel-filler cap is loose or missing, or if the vehicle runs out of fuel. Check to make sure the fuel-filler cap is installed and closed tightly , and that the vehicle has at least 3 gallons (11.4 liters) of fuel in the fuel tank. After a few driving trips, the light should turn off if n[...]

The slip indicator light also comes on when you place the ignition switch in the ON position. The light will turn off after about 2 seconds if the system is operational. If the light does not come on or does not go off, have the T raction Control System checked by a NISSAN dealer. T raction Control System off indicator light (if so equipped) This i[...]

Light reminder chime With the ignition switch placed in the OFF posi- tion, a chime sounds when the driver’s door is opened if the headlights or parking lights are on. T urn the headlight control switch off before leav- ing the vehicle. The vehicle information display s 1 is located on the bottom of the speedometer. It displays such items as: ●[...]

Fuel Economy mode The fuel economy mode can be selected to dis- play the instant fuel economy since the last reset. Average speed mode The average speed mode can be selected to display the average miles per gallon and miles per hour since the last reset. Time/Miles (km) mode The time/miles (km) mode can be selected to show the time and distance dri[...]

Range mode The range mode can be selected to give you an estimation of the distance that can be driven before refueling. The range is constantly calcu- lated based on the amount of fuel in the fuel tank and the actual fuel consumption. Exterior T emperature mode The exterior temperature mode can be selected to provide you with the temperature outsi[...]

Alert mode The alert mode allows you to set alerts notifying you of time to rest or icy conditions. The time to rest alert lets you know when you have been traveling for a long time and may need a break. The icy alert notifies you that icy driving condi- tions may exist. Reset mode The reset mode can be selected in any screen that allows for prefer[...]

Display mode The LANGUAGE/UNIT screen will appear when selecting the “Language/Unit” key and pressing . Language: English or French Unit: US — mile, °F , MPG Metric — km, °C, L/100 km Y ou can select the language and unit using the button and pressing . The settings are automatically saved when you exit the menu by pressing the BACK butto[...]

V ehicle information display warnings and indicators 1. Door and trunk open warning 2. Push warning (CVT models) 3. Low fuel warning 4. Low windshield washer fluid warning 5. No key warning 6. Parking brake warning 7. Shift P warning (CVT models) 8. Cruise main switch indicator 9. Cruise set switch indicator 10. Engine start operation indicator (CV[...]

11. Engine start operation indicator (MT mod- els) 12. NISSAN Intelligent K ey™ insertion indicator 13. NISSAN Intelligent K ey™ removal indicator 14. NISSAN Intelligent K ey™ battery discharge indicator 15. Steering lock release malfunction indicator Door and trunk open warning This warning illuminates when a door or the trunk has been opene[...]

cruise main switch indicator illuminates, the cruise control system is operational. Cruise set switch indicator This indicator illuminates while the vehicle speed is controlled by the cruise control system. If the indicator blinks while the engine is running, it may indicate the cruise control system is not function- ing properly . Have the system [...]

Y our vehicle may have two types of security sys- tems: ● V ehicle security system ● NISSAN V ehicle Immobilizer System V EHICLE SECURITY SYSTEM The vehicle security system provides visual and audible alarm signals if someone opens the doors or trunk lid when the system is armed. It is not, however, a motion detection type system that activates[...]

The alarm is activated by: ● opening the door or trunk lid without using the key or Intelligent K ey (even if the door is unlocked by releasing the door inside lock switch) . How to stop an activated alarm The alarm stops only by unlocking the driver’s door or the trunk lid with the key , pressing the button on the Intelligent K ey , or press- [...]

SWITCH OPERATION The windshield wiper and washer switch oper- ates when the ignition switch is placed in the ON position. Push the lever down to operate the wiper at the following speed: s 1 Intermittent — intermittent operation can be adjusted by turning the switch toward s A (Slower) or s B (Faster) . Also, for vehicles equipped with speed depe[...]

T o defrost the rear window glass and outside mirrors (if so equipped) , start the engine and push the rear window defroster switch on. The rear window defroster indicator light on the switch comes on. Push the switch again to turn the defroster off. The rear window defroster automatically turns off after approximately 15 minutes. CAUTION When clea[...]

X ENON HEADLIGHTS (if so equipped) WARNING c HIGH VOL T AGE ● When xenon headlights are on, they produce a high voltage. T o prevent an electric shock, never attempt to modify or disassemble. Always have your xe- non headlights replaced at a NISSAN dealer. ● X enon headlights provide considerably more light than conventional head- lights. If th[...]

CAUTION Use the headlights with the engine run- ning to avoid discharging the vehicle battery. Autolight system (if so equipped) The autolight system allows the headlights to be set so they turn on and off automatically . The autolight system can: ● T urn on the headlights, front parking, tail, license plate and instrument panel lights au- tomati[...]

T o turn on the autolight system: 1. T urn the headlight switch to the AUTO posi- tion s 1 . 2. Push the push-button ignition switch to the ON position. 3. The autolight system automatically turns the headlights on and off. Initially , if the ignition switch is placed in the OFF position and a door is opened and left open, the headlights remain ON [...]

CAUTION Even though the battery saver feature au- tomatically turns off the headlights after a period of time, you should turn the head- light switch to the OFF position when the engine is not running to avoid discharging the vehicle battery. DAYTIME RUNNING LIGHT SYSTEM (Canada only) The headlights automatically illuminate at a re- duced intensity[...]

T URN SIGNAL SWITCH T urn signal s 1 Move the lever up or down to signal the turning direction. When the turn is com- pleted, the turn signals cancel automatically . Lane change signal s 2 T o signal a lane change, move the lever up or down to the point where the indicator light begins to flash, but the lever does not latch. FOG LIGHT SWITCH (if so[...]

The flashers will operate with the ignition switch placed in any position. Some state laws may prohibit the use of the hazard warning flasher switch while driving. T o sound the horn, push the center pad area of the steering wheel. WARNING Do not disassemble the horn. Doing so could affect proper operation of the supplemental front air bag system. [...]

CAUTION ● Do not use the seat heater for extended periods or when no one is using the seat. ● Do not put anything on the seat which insulates heat, such as a blanket, cush- ion, seat cover, etc . Otherwise, the seat may become overheated. ● Do not place anything hard or heavy on the seat or pierce it with a pin or similar object. This may res[...]

The power outlets are for powering electrical accessories such as cellular telephones. They are rated at 12 volt, 120W (10A) maximum. The console outlet is powered directly by the vehi- cle’s battery . CAUTION ● The outlet and plug may be hot during or immediately after use. ● Only certain power outlets are designed for use with a cigarette l[...]

Open the lower half of the console box to access the power outlet. Refer to “Console box” in this section. MAP POCKETS SEATBACK POCKETS (if so equipped) The seatback pockets are located on the back of the driver’s and passenger’s seats. The pockets can be used to store maps. Console box WIC1262 WIC1263 LIC0016 STORAGE Instruments and contro[...]

STORAGE POUCH (if so equipped) A storage pouch is located on the front of the driver’s and passenger’s seats. WARNING Do not store angular, sharp, heavy objects or objects that cannot fully fit inside the pouch because they might increase the likelihood of an injury in a crash. SUNGLASSES HOLDER T o open the sunglasses holder, push and release.[...]

Front - T ype A LIC1075 Front - T ype B LIC1105 Rear (sedan) WRS0167 Instruments and controls 2-39 Z REVIEW COPY— 2009 Altima (alt) Owners Manual (owners) —USA_English (nna) 02/03/09—debbie X[...]

CUP HOLDERS T o open the front cup holders, push the cup holder lid. T o close, lower the cup holder lid and push down until it clicks in place. The plastic insert (if so equipped) may be re- moved to accommodate a larger cup size or for cleaning. The rear center cup holders are located in the rear fold-down armrest (sedan) or in the rear arm rest [...]

GLOVE BOX Open the glove box by pulling the handle. Use the master key when locking s 1 or unlocking s 2 the glove box. WARNING Keep glove box lid closed while driving to help prevent injury in an accident or a sudden stop. CONSOLE BOX Upper half Pull up on the driver’s side latch to open the upper half of the console box. The mat (if so equipped[...]

STORAGE BOX (if so equipped) COVERED STORAGE BOX Push the center of the lid to open. LIC1477 T ype A LIC1090 T ype B LIC1078 2-42 Instruments and controls Z REVIEW COPY— 2009 Altima (alt) Owners Manual (owners) —USA_English (nna) 02/03/09—debbie X[...]

GROCERY HOOKS (if so equipped) The grocery hooks are located in the trunk and can be used to hang a standard size plastic grocery bag. CAUTION Do not apply a total load of more than 20 lbs (9 kg) to a single grocery hook. CARGO NET (if so equipped) WARNING Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. I[...]

P OWER WINDOWS WARNING ● Make sure that all passengers have their hands, etc . inside the vehicle while it is in motion and before closing the windows. Use the window lock switch to prevent unexpected use of the power windows. ● Do not leave children unattended inside the vehicle. They could unknowingly ac- tivate switches or controls and becom[...]

Front passenger’s power window switch The passenger’s window switch operates only the corresponding passenger’s window . T o open the window , push the switch to the first detent and continue to hold it down until the desired window position is reached s 1 . T o close the window , pull the switch to the first detent and continue to hold it up[...]

Auto-reverse function If the control unit detects something caught in the window as it is closing, the window will be imme- diately lowered. The auto-reverse function can be activated when the window is closed by automatic operation when the ignition switch is placed in the ON position or for 45 seconds after the ignition switch is placed in the OF[...]

T o fully close the moonroof, push the switch toward s 2 . T o open or close the moonroof part way, push the switch in any direction while the moonroof is sliding to stop it in the desired position. Tilting the moonroof Close the moonroof by pushing the switch toward s 2 . Release the switch, then push the switch toward s 2 again to tilt the moonro[...]

Depending on the environment or driving conditions, the auto-reverse function may be activated if an impact or load similar to something being caught in the moonroof occurs. WARNING There are some small distances immedi- ately before the closed position which cannot be detected. Make sure that all passengers have their hands, etc ., inside the vehi[...]

The lights will go off when the ignition switch is placed in the ON position, or the driver’s door is closed and locked. The lights will also go off after 30 minutes when the doors are open. ● When the switch is in the OFF position s 3 , the interior light does not illuminate, regard- less of door position. NO TE: The doorstep lights illuminate[...]

T o turn the map lights on, press the light lens. T o turn them off, press the lens again. CAUTION Do not use for extended periods of time with the engine stopped. This could result in a discharged battery. T o turn the rear map lights on, press the switch. T o turn them off, press the switch again. The light illuminates when the trunk lid is opene[...]

The HomeLink T Universal T ransceiver provides a convenient way to consolidate the functions of up to three individual hand-held transmitters into one built-in device. HomeLink T Universal T ransceiver: ● Will operate most Radio Frequency (RF) devices such as garage doors, gates, home and office lighting, entry door locks and se- curity systems. [...]

3. Using both hands, simultaneously press and hold both the HomeLink T button you want to program and the hand-held transmitter but- ton. DO NO T release the buttons until step 4 has been completed. 4. Hold down both buttons until the indicator light on the HomeLink T flashes, changing from a “slow blink” to a “rapidly flashing blink” . Thi[...]

NO TE: When programming a garage door opener, etc ., it is advised to unplug the device dur- ing the “cycling” process to prevent pos- sible damage to the garage door opener components. OPERATING THE HOMELINK T UNIVERSAL TRANSCEIVER The HomeLink T Universal T ransceiver (once pro- grammed) may now be used to activate the ga- rage door, etc. T o[...]

NO TE: Following step 2, there are 30 seconds in which to initiate step 3. 3. Firmly press and release the programmed HomeLink T button a second time to com- plete the training process. (Some garage door openers may require you to do this procedure a third time to complete the train- ing.) The garage door opener should now recognize the HomeLink T [...]

3 Pre-driving checks and adjustments K e y s .............................................3 - 2 NISSAN Intelligent K ey™ ........................3 - 2 NISSAN V ehicle Immobilizer System keys .........3 - 3 Doors ............................................3 - 4 Locking with key ................................3 - 4 Locking with inside lock knob .[...]

1. T wo Intelligent Keys 2. Mechanical keys (inside Intelligent K eys) 3. K ey number plate NISSAN INTELLIGENT K EY™ Y our vehicle can only be driven with the Intelligent K ey which are registered to your vehicle’s Intelli- gent K ey components and NISSAN V ehicle Im- mobilizer System components. Never leave these keys in the vehicle. As many a[...]

Mechanical key The Intelligent K ey contains the mechanical key . T o remove the mechanical key, release the lock knob on the back of the Intelligent K ey . T o install the mechanical key, firmly insert it into the Intelligent K ey until the lock knob returns to the lock position. Use the mechanical key to lock or unlock the doors, trunk lid, glove[...]

WARNING ● Always have the doors locked while driving. Along with the use of seat belts, this provides greater safety in the event of an accident by helping to prevent persons from being thrown from the vehicle. This also helps keep children and others from unintentionally open- ing the doors, and will help keep out intruders. ● Before opening a[...]

LOCKING WITH INSIDE LOCK KNOB T o lock the door without the key, move the inside lock knob to the lock position s 1 , then close the door. T o unlock the door without the key, move the inside lock knob to the unlock position s 2 . LOCKING WITH POWER DOOR LOCK SWITCH T o lock all the doors without a key, push the door lock switch (driver’s or fron[...]

3. Do one of the following within 20 seconds of performing Step #2: ● T o change AUTO UNL OCK settings: push and hold the power door lock switch to the position (UNL OCK) for more than 5 seconds. ● T o change AUTO L OCK settings: push and hold the power door lock switch to the position (L OCK) for more than 5 seconds. 4. When activated, the haz[...]

CAUTION ● Be sure to carry the Intelligent Key with you when operating the vehicle. ● Never leave the Intelligent Key in the vehicle when you leave the vehicle. The Intelligent K ey is always communicating with the vehicle as it receives radio waves. The Intel- ligent K ey transmits weak radio waves. Environ- mental conditions may interfere wit[...]

● Do not attach the Intelligent Key with a key holder that contains a magnet. ● Do not place the Intelligent Key near equipment that produces a magnetic field, such as a TV , audio equipment and personal computers. If an Intelligent K ey is lost or stolen, NISSAN recommends erasing the ID code of that Intelli- gent K ey from the vehicle. This m[...]

DOOR LOCKS/UNLOCKS PRECAUTION ● Do not push the door handle request switch with the Intelligent K ey held in your hand as illustrated. The close distance to the door handle will cause the Intelligent K ey system to have difficulty recognizing that the Intelli- gent K ey is outside the vehicle. ● After locking with the door handle request switch[...]

Locking doors 1. Move the shift selector to the P (Park) posi- tion, place the ignition switch in the L OCK position and make sure you carry the Intelli- gent K ey with you. 2. Close all doors. 3. Push any door handle request switch s 1 while carrying the Intelligent K ey with you. 4. All doors and the trunk will lock. 5. The hazard warning lights [...]

NO TE: The doors may not lock when the Intelli- gent Key is in the same hand that is oper- ating the request switch to lock the door. Put the Intelligent Key in a purse, pocket or your other hand. CAUTION The lockout protection may not function under the following conditions: ● When the Intelligent Key is placed on top of the instrument panel. ?[...]

● Placing the ignition switch in the ON posi- tion. ● Locking the doors with the remote controller. ● Switching the room light switch to the OFF position. Opening the trunk lid 1. Push the trunk opener request switch s A for more than 1 second while carrying the Intel- ligent K ey with you. 2. The trunk will unlatch. A chime will sound 4 time[...]

Locking doors 1. Place the ignition switch in the L OCK posi- tion. 2. Close all doors. 3. Press the button on the Intelligent Ke y. 4. The hazard warning lights flash twice and the horn beeps once. 5. All doors will be locked. CAUTION After locking the doors using the Intelli- gent Key, be sure that the doors have been securely locked by operating[...]

The interior light illuminates for 15 seconds when a door is unlocked and the room light switch is in the DOOR position. The light can be turned off without waiting for 15 seconds by performing one of the following op- erations: ● Placing the ignition switch in the ON posi- tion. ● Locking the doors with the Intelligent K ey . ● Switching the[...]

The panic alarm stops when: ● It has run for 25 seconds, or ● Any button is pressed on the Intelligent K ey . ● Pushing the request switch on the driver or passenger door with the Intelligent K ey in range of the door handle. Silencing the horn beep feature If desired, the horn beep feature can be deacti- vated using the Intelligent K ey . T [...]

T ROUBLESHOOTING GUIDE V erify the location of all Intelligent Keys that are programmed for the vehicle. If another Intelligent K ey is in range or inside the vehicle, the vehicle system may respond differently than expected. Symptom Possible Cause Remedy When pushing the ignition switch to stop the engine The SHIFT P warning appears on the dis- pl[...]

WARNING ● Radio waves could adversely affect elec- tric medical equipment. Those who use a pacemaker should contact the electric medical equipment manufacturer for the possible influences before use. ● The Intelligent Key transmits radio waves when the buttons are pushed. The FA A advises the radio waves may affect aircraft navigation and commu[...]

As many as 4 Intelligent K eys can be registered and used with one vehicle. For information about the purchase and use of additional Intelligent K eys, contact a NISSAN dealer. CAUTION ● Do not allow the Intelligent Key, which contains electrical components, to come into contact with water or salt water. This could affect the system function. ●[...]

Locking doors 1. Place the ignition switch in the L OCK posi- tion. 2. Close all doors. 3. Press the button on the Intelligent Ke y. 4. The hazard warning lights flash twice and the horn beeps once. 5. All doors will be locked. CAUTION After locking the doors using the Intelli- gent Key, be sure that the doors have been securely locked by operating[...]

The interior light illuminates for 15 seconds when a door is unlocked and the room light switch is in the DOOR position. The light can be turned off without waiting for 15 seconds by performing one of the following op- erations: ● Placing the ignition switch in the ON posi- tion. ● Locking the doors with the Intelligent K ey . ● Switching the[...]

The panic alarm stops when: ● It has run for 25 seconds, or ● Any button is pressed on the Intelligent K ey . ● Pushing the request switch on the driver or passenger door with the Intelligent K ey in range of the door handle. Silencing the horn beep feature If desired, the horn beep feature can be deacti- vated using the Intelligent K ey . T [...]

T ROUBLESHOOTING GUIDE V erify the location of all Intelligent Keys that are programmed for the vehicle. If another Intelligent K ey is in range or inside the vehicle, the vehicle system may respond differently than expected. Symptom Possible Cause Remedy When pushing the ignition switch to stop the engine The SHIFT P warning appears on the dis- pl[...]

s 1 Pull the hood lock release handle located below the driver’s side instrument panel; the hood springs up slightly . s 2 Lift the lever at the front of the hood with your fingertips and raise the hood. s 3 Remove the support rod from the clamp. s 4 Insert the support rod into the hole on the passenger’s side of the hood. s 5 When closing the [...]

● Closely supervise children when they are around cars to prevent them from playing and becoming locked in the trunk where they could be seriously in- jured. Keep the car locked, with the rear seatback and trunk lid securely latched when not in use, and prevent children’s access to car keys. T o open the trunk lid, push the opener switch down. [...]

T o open the trunk from the inside, pull the illumi- nated release handle until the lock releases and push up on the trunk lid. The release handle is made of a material that glows in the dark after a brief exposure to ambient light. The handle is located inside the trunk compart- ment on the interior of the trunk lid. OPENER OPERATION The fuel-fill[...]

WARNING ● Gasoline is extremely flammable and highly explosive under certain condi- tions. Y ou could be burned or seriously injured if it is misused or mishandled. Always stop the engine and do not smoke or allow open flames or sparks near the vehicle when refueling. ● Fuel may be under pressure. T urn the cap a third of a turn, and wait for a[...]

TILT OPERATION Pull the lever s 1 all the way toward you and adjust the steering wheel up or down s 2 to the desired position. Lock the wheel by releasing the lever and ensure that the lever has returned to its original position. WARNING Do not adjust the steering wheel while driving. Y ou could lose control of your vehicle and cause an accident. T[...]

s 3 Slide the extension sun visor (if so equipped) in or out as needed. CAUTION Do not store the sun visor before returning the extension to its original position. V ANITY MIRRORS T o access the vanity mirror, pull the sun visor down and flip open the mirror cover. Some vanity mirrors are illuminated and turn on when the mirror cover is open. REARV[...]

AUTOMATIC ANTI-GLARE REARVIEW MIRROR (if so equipped) The inside mirror is designed so that it automati- cally dims according to the intensity of the head- lights of the vehicle following you. The automatic anti-glare feature operates only when the ignition switch is in the ON position. The indicator light s 1 will illuminate when the automatic ant[...]

Manual folding outside mirrors (if so equipped) Pull the outside mirror toward the door to fold it. WPD0056 3-30 Pre-driving checks and adjustments Z REVIEW COPY— 2009 Altima (alt) Owners Manual (owners) —USA_English (nna) 02/03/09—debbie X[...]

Pre-driving checks and adjustments 3-31 MEMO[...]

4 Monitor, climate, audio, phone and voice recognition systems Control panel buttons (if so equipped) ...............4 - 2 Setting up the start-up screen ...................4 - 3 How to use the SETUP button ...................4 - 3 button ...................................4 - 7 RearView Monitor (if so equipped) ...................4 - 8 How to read[...]

Bluetooth T Hands-Free Phone System with Navigation System (if so equipped) ................. 4-61 Regulatory Information ......................... 4-62 V oice commands .............................. 4-63 Pairing procedure ............................. 4-63 Phone download .............................. 4-64 Making a call ...........................[...]

WARNING ● Do not disassemble or modify this sys- tem. If you do, it may result in accidents, fire, or electrical shock. ● Do not use this system if you notice any abnormality, such as a frozen screen or lack of sound. Continued use of the system may result in accident, fire or electric shock. ● In case you notice any foreign object in the sys[...]

When you use this system, make sure the engine is running. If you use the system with the engine not running (ignition ON or ACC) for a long time, it will use up all the battery power, and the engine will not start. Reference symbols: SETUP button — This is a button on the control panel. “Display” key — This is a select key on the touch- sc[...]

Display settings T ouch the “Display” key . The display screen will appear. Display/brightness/contrast : T ouch the “–” key or the “+” key to adjust the brightness and contrast of the screen. The new settings are automatically saved when you exit the setting screen by touching the “Back” key or pressing any other mode button. Dis[...]

Clock Adjusting the time: The following display will appear when pressing the SETUP button, then touching the “Clock” key. On-screen Clock: When this item is turned on, a clock is always displayed in the upper right corner of the screen. This clock will indicate the time almost exactly because it is always adjusted by the GPS system. T o turn o[...]

After selection, touch the “Back” key the Clock screen will appear. Pacific zone has been set as the initial (default) setting. Beep setting T ouch the “Volumes/T ones” key. T ouch the But- ton Beeps “ON” key to turn on or turn off the beep sound. T o accept the changes touch the “Back” key . With this option on, a beep will sound i[...]

Select Language: T ouch the “Select Language” key . From the fol- lowing display , select the English “ON” key or the Français “ON” key for your language preference. If you select the “Français” key , French language will be displayed. T o obtain a French Owner’s Manual, please see “Owner’s Manual / Service Manual order info[...]

When the shift selector is shifted into the R (Reverse) position, the monitor display shows the view directly to the rear of the vehicle. WARNING ● The system is designed as an aid to the driver in detecting large stationary ob- jects to help avoid damaging the ve- hicle. The system will not detect small objects below the bumper, and may not dete[...]

ADJUSTING THE SCREEN T o adjust the quality of the screen, press the SETUP button. ● T o adjust the Brightness, Tint, Contrast, Dis- play ON/OFF and Color of the RearView Monitor, press the SETUP button with the RearView Monitor on, then touch the “–” or “+” key on the item and adjust the level. ● Do not adjust the Brightness, Contras[...]

Adjust air flow direction by moving the vent slides. Open or close the vents by using the dial. Move the dial toward the to open the vents or toward the to close them. Right and Left WHA0736 Center WHA0737 Rear (sedan, if so equipped) WHA0688 V ENTS 4-10 Monitor, climate, audio, phone and voice recognition systems Z REVIEW COPY— 2009 Altima (alt)[...]

WARNING ● The air conditioner cooling function op- erates only when the engine is running. ● Do not leave children or adults who would normally require the assistance of others alone in your vehicle. Pets should also not be left alone. They could accidentally injure themselves or others through inadvertent operation of the vehicle. Also, on hot[...]

— Air flows from center and side vents and foot outlets. — Air flows mainly from foot outlets. — Air flows from defroster outlets and foot outlets. — Air flows mainly from defroster outlets. T emperature control dial The temperature control dial allows you to adjust the temperature of the outlet air. T o lower the temperature, turn the dial[...]

3. T urn the temperature control dial to the de- sired position between the middle and the hot position. ● T o quickly remove ice or fog from the win- dows, turn the fan control dial to the highest setting and the temperature control to the full HO T position. ● When the position is selected, the air conditioner automatically turns on (however,[...]

● For quick cooling when the outside tem- perature is high, push the button to the ON position. Be sure to return the to the OFF position for normal cooling. MAX A/C may be used for quick cooling. Dehumidified heating This mode is used to heat and dehumidify the air. 1. Press the button to the OFF position. 2. Press the air flow control button. 3[...]

WHA1179 WHA1180 Monitor, climate, audio, phone and voice recognition systems 4-15 Z REVIEW COPY— 2009 Altima (alt) Owners Manual (owners) —USA_English (nna) 02/03/09—debbie X[...]

WHA1181 WHA1182 4-16 Monitor, climate, audio, phone and voice recognition systems Z REVIEW COPY— 2009 Altima (alt) Owners Manual (owners) —USA_English (nna) 02/03/09—debbie X[...]

WHA1183 Monitor, climate, audio, phone and voice recognition systems 4-17 Z REVIEW COPY— 2009 Altima (alt) Owners Manual (owners) —USA_English (nna) 02/03/09—debbie X[...]

1. Driver temperature control dial 2. Air flow control buttons 3. Passenger temperature control dial 4. DUAL button 5. Rear defrost button 6. Front window defrost button 7. Fan speed dial/system OFF button 8. Air recirculation button 9. A/C ON/OFF button 10. AUT O button WARNING ● The air conditioner cooling function op- erates only when the engi[...]

● The temperature of the passenger compart- ment will be maintained automatically . Air flow distribution, fan speed and A/C on/off are also controlled automatically . ● A visible mist may be seen coming from the vents in hot, humid conditions as the air is cooled rapidly . This does not indicate a mal- function. Dehumidified defrosting or defo[...]

OPERATING TIPS ● When the engine coolant temperature and outside air temperature are low , the air flow from the foot outlets may not operate for a maximum of 150 seconds. However, this is not a malfunction. After the coolant tempera- ture warms up, air flow from the foot outlets will operate normally . The sunload sensor, located on the top of t[...]

RADIO With the ignition placed in the ACC or ON posi- tion, press the PWR (power)/VOL (volume) knob to turn the radio on. If you listen to the radio with the engine not running, the ignition should be placed in the ACC position. Radio reception is affected by station signal strength, distance from radio transmitter, build- ings, bridges, mountains [...]

SATELLITE RADIO RECEPTION (if so equipped) When the satellite radio is used for the first time or the battery has been replaced, the satellite radio may not work properly . This is not a mal- function. W ait more than 10 minutes with satellite radio ON and the vehicle outside of any metal or large building for satellite radio to receive all of the [...]

● Do not expose the CD to direct sun- light. ● CDs that are in poor condition or are dirty, scratched or covered with finger- prints may not work properly. ● The following CDs may not work prop- erly: ● Copy control compact disc s (CCCD) ● Recordable compact disc s (CD-R) ● Rewritable compact disc s (CD-RW) ● Do not use the following [...]

● Sampling frequency — Sampling frequency is the rate at which the samples of a signal are converted from analog to digital (A/D conversion) per second. ● Multisession — Multisession is one of the methods for writing data to media. W riting data once to the media is called a single session, and writing more than once is called a multisessio[...]

Specification chart : Supported media CD, CD-R, CD-RW Supported file systems ISO9660 LEVEL1, ISO9660 LEVEL2, Apple ISO, Romeo, Joliet * ISO9660 Level 3 (packet writing) is not supported. Supported versions*1 MP3 V ersion MPEG1, MPEG2, MPEG2.5 Sampling frequency 8 kHz - 48 kHz Bit rate 8 kbps - 320 kbps, VBR WMA V ersion WMA7, WMA8, WMA9 Sampling fr[...]

T roubleshooting guide: Symptom Cause and Countermeasure Cannot play Check if the disc was inserted correctly. Check if the disc is scratched or dirty. Check if there is condensation inside the player. If there is, wait until the condensation is gone (about 1 hour) before using the player. If there is a temperature increase error, the CD player wil[...]

1. SEEK/TRACK button 2. CD insert slot 3. TUNE/FF·REW button 4. CD eject button 5. AUDIO button (BASS, TREBLE, F ADE and BALANCE) 6. CL OCK button 7. AUX IN jack 8. SCAN button 9. RDM/RPT button 10. PWR/VOL control knob 11. AUX button 12. RADIO button 13. CD button 14. DISP button 15. PRESET A·B·C button 16. Station select (1 - 6) buttons 17. pa[...]

AUDIO button (Bass, T reble, Fade and Bal- ance) Press the AUDIO button to change the mode as follows: Bass → T reble → Fade → Balance → Beep ON/OFF → Audio → Bass T o adjust Bass, T reble, Fade and Balance press the AUDIO button until the desired mode ap- pears in the display . Press the TUNE/FF·REW or to adjust Bass and T reble to th[...]

When the RADIO button is pressed while the ignition switch is in the ACC or ON position, the radio will come on at the station last played. If a compact disc is playing when the RADIO button is pressed, the compact disc will auto- matically be turned off and the last radio station played will come on. The FM stereo indicator, ST , illuminates durin[...]

Each time the button is pressed, the CD ad- vances 1 additional track. The track number ap- pears in the display window . (When the last track on the compact disc is skipped, the first track is played.) When is pressed, the track being played returns to the beginning. Press several times to skip back several tracks. Each time the button is pressed [...]

1. SEEK/TRACK button 2. CD insert slot 3. TUNE/FF·REW button 4. CD eject button 5. AUDIO button (BASS, TREBLE, F ADE, SSV , BALANCE and BEEPS) 6. CL OCK button 7. AUX IN jack 8. SCAN button 9. RDM/RPT button 10. PWR/VOL control knob 11. AUX button 12. RADIO* button 13. CD button 14. DISP button 15. PRESET A·B·C button 16. Station and CD select ([...]

operational then pressing the RADIO button will switch between FM and AM bands. Audio main operation PWR/VOL control knob Place the ignition switch in the ACC or ON position, and then press the PWR/VOL control knob while the system is off to call up the mode (radio or CD) which was playing immediately before the system was turned off. T o turn the [...]

CD display mode T o change the text displayed while playing a CD with text, press the DISP button. The DISP button will allow you to scroll through CD text as follows: T rack number and T rack time ←→ Album title ←→ Song title. ● T rack number displays the track number se- lected on the disc. ● T rack time displays the amount of time th[...]

TUNE/FF·REW (tuning) button: Press the TUNE/FF·REW button or for manual tuning. T o move quickly through the channels, hold the tuning buttons down. SEEK (tuning) button: Press the SEEK/TRACK button or to tune from high to low or low to high frequen- cies and stop at the next broadcasting station. SCAN (tuning) button: Press the SCAN button. SCAN[...]

The slot numbers (1 – 6) will illuminate on the display when CDs are loaded into the changer. CD button: When the CD button is pressed with the system off and the compact disc loaded, the system will turn on and the compact disc will start to play . When the CD button is pressed with the com- pact disc loaded but the radio playing, the radio will[...]

SCAN button: 1 Disc , All T racks While listening to a CD, press the SCAN button to preview the first 10 seconds of each track on the CD playing. Pressing the SCAN button again during this 10 second period stops the scan and the CD remains on that track. All Disc s, 1 T rack While listening to a CD with other CDs loaded into the CD changer, press a[...]

1. RADIO* button 2. T ouch-screen keys (vary depending on what function is selected) 3. SEEK/TRACK button 4. TUNE·FOLDER and AUDIO control knob (BASS, TREBLE, BALANCE, F ADE and SSV (if so equipped)) 5. Station and CD select (1 - 6) buttons 6. CD insert slot 7. CD changer select (1 - 6) buttons 8. CD eject button 9. AUX jack 10. A·B·C button 11.[...]

FM/AM/SA T RADIO WITH COMPACT DISC (CD) CHANGER (if so equipped) For all operation precautions, see “ Audio opera- tion precautions” earlier in this section. No satellite radio reception is available unless there is an active XM T satellite radio service subscription. Satellite radio is not available in Alaska, Hawaii and Guam. If satellite rad[...]

CD display mode While listening to a CD or an MP3/WMA CD certain text might be displayed (when CD en- coded with text is being used) . Depending on how the CD or MP3/WMA CD is encoded the following text might be displayed during CD playback: ● Disc number displays which disc is playing ● Folder number displays the folder number on the CD that i[...]

SEEK/TRACK (tuning) button: Press the SEEK/TRACK button or for less than 1.5 seconds to tune from high to low or low to high frequencies and stop at the next broadcasting station. “Scan” (tuning) key: T ouch the “Scan” key . SCAN illuminates in the display window . Scan tuning begins from low to high frequencies. Scan tuning stops for 5 sec[...]

The slot numbers (1 – 6) will illuminate on the display when CDs are loaded into the changer. When one of the CD changer (1 – 6) buttons is pressed with the compact disc loaded but the radio playing, the radio will automatically be turned off and the compact disc will start to play . DISC button: When the DISC button is pressed with the sys- te[...]

MP3 CD: 1 DISC RPT → 1 FOLDER RPT → 1 TRACK RPT 1 DISC RPT : The disc that is currently playing will be repeated. 1 TRACK RPT : The track that is currently playing will be repeated 1 FOLDER RPT : The folder that is currently play- ing will be repeated. “Random” key: When the “Random” key is touched while a com- pact disc is played, the [...]

CD CARE AND CLEANING ● Handle a CD by its edges. Do not bend the disc. Never touch the surface of the disc. ● Always place the discs in the storage case when they are not being used. ● T o clean a disc, wipe the surface from the center to the outer edge using a clean, soft cloth. Do not wipe the disc using a circular motion. ● Do not use a [...]

1. Source select and P ower on switch 2. T uning switch 3. V olume control switch 1. Source select and P ower on switch 2. T uning switch 3. V olume control switch STEERING WHEEL SWITCH FOR AUDIO CONTROL (if so equipped) POWER on switch With the ignition switch in the ACC or ON posi- tion, push the SOURCE switch to turn the audio system on. SOURCE [...]

Seek tuning (radio) : Push the tuning switch or for more than 1.5 seconds to seek the next or previous radio station. Next/Previous track (CD) : Push the tuning switch or for less than 1.5 seconds to return to the beginning of the present track or skip to the next track. Push several times to skip back or skip through tracks. Change disc (CD) (if s[...]

CAUTION ● Keep the antenna as far away as pos- sible from the electronic control modules. ● Keep the antenna wire more than 8 in (20 cm) away from the electronic con- trol system harnesses. Do not route the antenna wire next to any harness. ● Adjust the antenna standing-wave ratio as recommended by the manufacturer. ● Connect the ground wir[...]

Y our NISSAN is equipped with the Bluetooth T Hands-Free Phone System. If you have a com- patible Bluetooth T enabled cellular phone, you can set up the wireless connection between your cellular phone and the in-vehicle phone module. With Bluetooth T wireless technology , you can make or receive a hands-free telephone call with your cellular phone [...]

– Y our cellular phone is locked to prevent it from being dialed. ● When the radio wave condition is not ideal or ambient sound is too loud, it may be difficult to hear the other person’s voice dur- ing a call. ● Do not place the cellular phone in an area surrounded by metal or far away from the in-vehicle phone module to prevent tone quali[...]

Operating tips T o get the best performance out of the NISSAN V oice Recognition system, observe the following: ● K eep the interior of the vehicle as quiet as possible. Close the windows to eliminate surrounding noises (traffic noises, vibration sounds, etc.) , which may prevent the system from recognizing voice commands correctly . ● W ait un[...]

● Numbers can be spoken in small groups. The system will prompt you to continue en- tering digits, if desired. Example: 1-800-662-6200 – “One eight zero zero” The system repeats the numbers and prompts you to enter more. – “six six two” The system repeats the numbers and prompts you to enter more. – “six two zero zero” ● Say ?[...]

PHONE/END Press the button to cancel a VR session or end a call. GETTING STARTED The following procedures will help you get started using the Bluetooth T Hands-Free Phone System with NISSAN V oice Recognition. For ad- ditional command options, refer to “List of voice commands” later in this section. Choosing a language Y ou can interact with th[...]

4. Say: “New phone” s C . The system acknowl- edges the command and asks you to initiate pairing from the phone handset s D . The pairing procedure of the cellular phone varies according to each cellular phone model. See the cellular phone Owner’s Manual for details. Y ou can also visit www .nissanusa.com/bluetooth for instruc- tions on pairi[...]

For additional command options, see “List of voice commands” later in this section. LIST OF VOICE COMMANDS Main Menu “Call” or “Call International” “Phone Book” “Memo Pad” “Setup” When you press and release the button on the steering wheel, you can choose from the commands on the Main Menu. The following pages describe these[...]

If a redial number does not exist, the system announces, “There is no number to redial” and ends the VR session. “Call back” s D Use the Call Back command to dial the number of the last incoming call within the vehicle. The system acknowledges the command, re- peats the number and begins dialing. If a call back number does not exist, the sy[...]

NO TE: Each phone has its own separate phone book. Y ou cannot access Phone A’s phone book if you are currently connected with Phone B . “New entry” s A Use the New Entry command to store a new name in the system. When prompted by the system, say the name you would like to give the new entry . For example, say: “Mary .” If the name is too[...]

The transfer procedure varies according to each cellular phone. See the cellular phone Owner’s Manual for details. Y ou can also visit www .nissanusa.com/bluetooth for instructions on transferring phone numbers from NISSAN recommended cellular phones. The system repeats the number and prompts you for the next command. When you have finished enter[...]

“Setup” Main Menu “Setup” “Pair Phone” s A “List Phone” s B “Select Phone” s C “Change Priority” s D “Delete Phone” s E “Select Ringtone” s F “Bluetooth Off” s G Use the Setup command to change options as- sociated with the Bluetooth T Hands-Free Phone System. “Pair phone” s A Use the Pair Phone command to pa[...]

and you change the priority level of Phone C to Level 1, then: Priority Level 1 = Phone C Priority Level 2 = Phone B Priority Level 3 = Phone A “Delete phone” s E Use the Delete Phone command to delete a specific phone or all phones from the Bluetooth T Hands-Free Phone System. The system announces the names of the phones already paired with th[...]

For information on selecting a different lan- guage, see “Choosing a language” earlier in this section. 6. V oice memory A or memory B is selected automatically . If both memory locations are already in use, the system will prompt you to overwrite one. Follow the instructions pro- vided by the system. 7. When preparation is complete and you are[...]

T ROUBLESHOOTING GUIDE The system should respond correctly to all voice commands without difficulty . If problems are en- countered, try the following solutions. Where the solutions are listed by number, try each solution in turn, starting with number 1, until the problem is resolved. Symptom Solution System fails to interpret the command correctly[...]

WARNING ● Use a phone after stopping your vehicle in a safe location. If you have to use a phone while driving, exercise extreme caution at all times so full attention may be given to vehicle operation. ● If you are unable to devote full attention to vehicle operation while talking on the phone, pull off the road to a safe location and stop you[...]

module when the ignition switch is turned to the ON position with the paired cellular phone turned on and carried in the vehicle. Y ou can register up to 5 different Bluetooth T cellular phones to the in-vehicle phone module. However, you can talk on only one cellular phone at a time. NISSAN V oice Recognition system supports the phone commands, so[...]

2. this device must accept any interference, including interference that may cause un- desired operation of the device. IC Regulatory information – Operation is subject to the following two con- ditions: (1) this device may not cause interfer- ence, and (2) this device must accept any interference, including interference that may cause undesired [...]

PHONE DOWNLOAD Up to 70 phone numbers can be stored in the phonebook. 1. Press the SETUP button, then touch the “Phone” key . 2. T ouch the “Phonebook” key . 3. T ouch one of the “None (Add New)” keys from the name list of the phonebook. 4. T ouch the “Bluetooth” key in order to trans- fer a phonebook entry from your cellular phone [...]

5. Operate the cellular phone to send a per- son’s name and phone number from the memory of the cellular phone. The memory sending procedure from the cellular phone varies according to each cellular phone manufacturer. See the cellular phone Own- er’s Manual for more details. 6. If you want to add a voice tag, touch the “Y es” key on the Ad[...]

MAKING A CALL T o make a call, follow the procedure below. 1. Press the phone button on the steer- ing wheel switches. The phone screen will appear on the display . 2. T ouch the “Phonebook” key . 3. T ouch one of the downloaded person’s key from the list. Dialing will start. 4. After the call is over, perform one of the following to finish t[...]

Hold Call: Continue to hold call. Reject Call: Reject an incoming call. T o finish the call, follow one of the procedures listed below: a. T ouch the “Reject Call” key on the display . b. Press and hold the phone button on the steering wheel switches. DURING A CALL There are some options available during a call. Select one of the following disp[...]

PHONE SETTING T o set up the hands-free phone system to your preferred settings, press the SETUP button, then touch the “Phone” key on the display. Phonebook: See “Phonebook download” earlier in this sec- tion. Downloaded Phonebook: See the following information for each item. ● Download All: T ransfer phonebook entries from your cellu- l[...]

Bluetooth Setup: See the following information for each item. ● Bluetooth Hands-Free: If this item is turned off, the connection be- tween the cellular phone and the in-vehicle phone module will be canceled. ● Paired Phone List : Up to 5 registered cellular phones are shown on the list. ● Pair Phone: See “Pairing Procedure” in this sectio[...]

Giving voice commands 1. Press the button. 2. The system announces: “Please say a com- mand” 3. After the tone sounds and the face icon of the display changes, speak a command. For additional information, see “List of voice commands” later in this section. 4. V oice and message feedback will be pro- vided when the command is accepted. ● I[...]

● say “Dial” or “Phone dial” the system will respond with “Please say the first group of numbers” , then say: – “one eight oh oh six six two six two oh oh” , – “one eight hundred six six two six two oh oh” , or – “one eight zero zero six six two six two oh oh” . Note 1: For the best voice recognition phone dialing re[...]

● “PHONEBOOK <voicetag> ” Shows the specified “voicetag” entry in the “phone book” and dials the phone number registered in the specified “voicetag” after pressing the ENTER button on the steering wheel. ● “ PHONEBOOK [PLA Y] DIRECT OR Y” or “PLA Y PHONEBOOK [DIRECT OR Y]” Dials the phone number registered in the p[...]

T ROUBLESHOOTING GUIDE The system should respond correctly to all voice commands without difficulty . If problems are en- countered, follow the solutions given in this guide for the appropriate error. Where the solutions are listed by number. T ry each solution in turn, starting with number one, until the problem is resolved. Symptom/error message [...]

4-74 Monitor, climate, audio, phone and voice recognition systems MEMO[...]

5 Starting and driving Precautions when starting and driving ................5 - 2 Exhaust gas (carbon monoxide) ..................5 - 2 Three-way catalyst ..............................5 - 2 Tire pressure monitoring system (TPMS) ..........5 - 3 Avoiding collision and rollover ....................5 - 5 Off-road recovery ...........................[...]

WARNING ● Do not leave children or adults who would normally require the assistance of others alone in your vehicle. Pets should also not be left alone. They could accidentally injure themselves or others through inadvertent operation of the vehicle. Also, on hot, sunny days, temperatures in a closed vehicle could quickly become high enough to ca[...]

CAUTION ● Do not use leaded gasoline. Deposits from leaded gasoline will seriously re- duce the three-way catalyst’s ability to help reduce exhaust pollutants. ● Keep your engine tuned up. Malfunc- tions in the ignition, fuel injection, or electrical systems can cause overrich fuel flow into the three-way catalyst, causing it to overheat. Do [...]

Additional information: ● The TPMS does not monitor the tire pressure of the spare tire. ● The TPMS will activate only when the vehicle is driven at speeds above 16 MPH (25 km/h) . Also, this system may not detect a sudden drop in tire pressure (for example a flat tire while driving) . ● The low tire pressure warning light does not automatica[...]

● When a spare tire is mounted or a wheel is replaced, tire pressure will not be indicated, the TPMS will not function and the low tire pressure warning light will flash for approximately 1 minute. The light will remain on after 1 minute. Contact your NISSAN dealer as soon as possible for tire replacement and/or system resetting. ● Replacing ti[...]

OFF-ROAD RECOVERY While driving, the right side or left side wheels may unintentionally leave the road surface. If this occurs, maintain control of the vehicle by follow- ing the procedure below . Please note that this procedure is only a general guide. The vehicle must be driven as appropriate based on the con- ditions of the vehicle, road and tra[...]

DRINKING ALCOHOL/DRUGS AND DRIVING WARNING Never drive under the influence of alcohol or drugs. Alcohol in the bloodstream re- duces coordination, delays reaction time and impairs judgement. Driving after drinking alcohol increases the likelihood of being involved in an accident injuring yourself and others. Additionally, if you are injured in an a[...]

The ignition switch is equipped with an anti-theft steering lock device. The ignition lock is designed so that the ignition switch position cannot be switched to OFF until the shift selector is moved to the P (Park) position (CVT) or N (Neutral) position (MT) . When the ignition switch cannot be pushed to- ward the OFF position, proceed as follows:[...]

If the battery of the Intelligent K ey is almost dis- charged, the guide light s A of the Intelligent K ey port blinks and the indicator appears on the ve- hicle information display . See “Vehicle informa- tion display” in the “Instruments and controls” section. In this case, inserting the Intelligent K ey into the port s B allows you to st[...]

● Make sure the area around the vehicle is clear. ● Check fluid levels such as engine oil, cool- ant, brake fluid, and window washer fluid as frequently as possible, or at least whenever you refuel. ● Check that all windows and lights are clean. ● Visually inspect tires for their appearance and condition. Also check tires for proper inflati[...]

4. Warm-up Allow the engine to idle for at least 30 sec- onds after starting. Do not race the engine while warming it up. Drive at moderate speed for a short distance first, especially in cold weather. In cold weather, keep the en- gine running for a minimum o f2-3 minutes before shutting it off. Starting and stopping the engine over a short period[...]

The CVT is designed so the foot brake pedal MUST be depressed before shifting from P (Park) to any drive position while the ignition switch is in the ON position. The shift selector cannot be moved out of P (Park) and into any of the other gear posi- tions if the ignition switch is placed in the LOCK or ACC position. T o move the shift selector: Pu[...]

R (Reverse) : CAUTION T o prevent transmission damage, use the P (Park) or R (Reverse) position only when the vehicle is completely stopped. Use the R (Reverse) position to back up. Make sure the vehicle is completely stopped before selecting the R (Reverse) position. The brake pedal must be depressed to move the shift selector from P (Park) , N (N[...]

● The transmission will automatically down- shift the gears. (For example, if you select the 3rd range, the transmission will shift down between the 3rd and 1st gears.) ● Moving the shift selector rapidly to the same side twice will shift the ranges in succession. When canceling the manual shift mode: Return the shift selector to the D (Drive) [...]

T o move the shift selector, complete the following procedure: 1. Push the ignition switch to the L OCK posi- tion. 2. Apply the parking brake. 3. Remove the shift lock release cover as shown. 4. Insert a small screwdriver in the shift lock release slot and push down. 5. Move the shift selector to the N (Neutral) position while holding down the shi[...]

MANUAL TRANSMISSION (if so equipped) WARNING ● Do not downshift abruptly on slippery roads. This may cause a loss of control. ● Do not over-rev the engine when shift- ing to a lower gear. This may cause a loss of control or engine damage. CAUTION ● Do not rest your foot on the clutch pedal while driving. This may cause clutch damage. ● Full[...]

For normal acceleration in low altitude areas (less than 4,000 ft [1219 m]): For QR25DE: GEAR CHANGE ACCEL shift point MPH (km/h) CRUISE shift point MPH (km/h) 1st to 2nd 15 (24) 8 (24) 2nd to 3rd 25 (40) 17 (27) 3rd to 4th 33 (53) 25 (40) 4th to 5th 44 (71) 36 (58) 5th to 6th 51 (82) 51 (82) For VQ35DE: GEAR CHANGE ACCEL shift point MPH (km/h) CRU[...]

WARNING ● Be sure the parking brake is fully re- leased before driving. Failure to do so can cause brake failure and lead to an accident. ● Do not release the parking brake from outside the vehicle. ● Do not use the gear shift in place of the parking brake. When parking, be sure the parking brake is fully engaged. ● Do not leave children un[...]

1. CANCEL switch 2. ACCEL/RES switch 3. COAST/SET switch 4. ON/OFF switch PRECAUTIONS ON CRUISE CONTROL ● If the cruise control system malfunctions, it cancels automatically . The SET indicator light in the instrument panel then blinks to warn the driver. ● If the SET indicator light blinks, turn the cruise control switch off and have the sys- [...]

The cruise control is automatically canceled and the SET light in the instrument panel goes out if: ● you depress the brake or clutch pedal while pushing the ACCEL/RES or SET/COAST switch. The preset speed is deleted from memory . ● the vehicle slows down more than 8 MPH (13 km/h) below the set speed. ● you depress the clutch pedal (manual tr[...]

● Accelerate slowly and smoothly . Maintain cruising speeds with a constant accelerator position. ● Drive at moderate speeds on the highway . Driving at high speed lowers fuel economy . ● Avoid unnecessary stopping and braking. Maintain a safe distance behind other ve- hicles. ● Use a proper gear range which suits road conditions. On level [...]

WARNING ● Do not stop or park the vehicle over flammable materials such as dry grass, waste paper or rags. They may ignite and cause a fire. ● Safe parking procedures require that both the parking brake be set and the transmission placed into P (Park) for CVT models or in an appropriate gear for manual transmission models. Fail- ure to do so co[...]

The power assisted steering uses a hydraulic pump, driven by the engine, to assist steering. If the engine stops or the drive belt breaks, you will still have control of the vehicle. However, much greater steering effort is needed, especially in sharp turns and at low speeds. WARNING If the engine is not running or is turned off while driving, the [...]

T o dry the brakes, drive the vehicle at a safe speed while lightly pressing the brake pedal to heat up the brakes. Do this until the brakes return to normal. Avoid driving the vehicle at high speeds until the brakes function correctly . ANTI-LOCK BRAKING SYSTEM (ABS) WARNING ● The Anti-lock Braking System (ABS) is a sophisticated device, but it [...]

Normal operation The ABS operates at speeds abov e3-6M P H( 5 - 10 km/h) . The speed varies according to road conditions. When the ABS senses that 1 or more wheels are close to locking up, the actuator rapidly applies and releases hydraulic pressure. This action is similar to pumping the brakes very quickly . Y ou may feel a pulsation in the brake [...]

● When driving on extremely inclined sur- faces such as higher banked corners, the T raction Control System may not operate properly and the indica- tor light may come on. Do not drive on these types of roads. ● If wheels or tires other than the recom- mended ones are used, the T raction Control System may not operate prop- erly and the indicat[...]

● Do not modify the vehicle’s suspension. If suspension parts such as shock ab- sorbers, struts, springs, stabilizer bars, bushings and wheels are not NISSAN approved for your vehicle or are ex - tremely deteriorated the V ehicle Dy- namic Control system may not operate properly. This could adversely affect ve- hicle handling performance, and t[...]

DRAINING OF COOLANT WATER If the vehicle is to be left outside without anti- freeze, drain the cooling system, including the engine block. Refill before operating the vehicle. For details, see “Changing engine coolant” in the “Maintenance and do-it-yourself” section of this manual. TIRE EQUIPMENT 1. SUMMER tires have a tread designed to pro[...]

ENGINE BLOCK HEATER (if so equipped) WARNING ● Do not use your engine block heater with an ungrounded electrical system or a 2-pronged adapter. Y ou can be se- riously injured by an electrical shock if you use an ungrounded connection. ● Disconnect and properly store the en- gine block heater cord before starting the engine. Damage to the cord [...]

5-30 Starting and driving MEMO[...]

6 In case of emergency Flat tire ...........................................6 - 2 Tire Pressure Monitoring System (TPMS) ..........6 - 2 Changing a flat tire .............................6 - 2 Jump starting .....................................6 - 7 Push starting ......................................6 - 9 If your vehicle overheats ................[...]

TIRE PRESSURE MONITORING SYSTEM (TPMS) This vehicle is equipped with the Tire Pressure Monitoring System (TPMS) . It monitors tire pres- sure of all tires except the spare. When the low tire pressure warning light is lit, one or more of your tires is significantly under-inflated. If the vehicle is being driven with low tire pressure, the TPMS will [...]

WARNING ● Make sure the parking brake is securely applied and the manual transmission is shifted into R (Reverse) , or the CVT is shifted into P (Park) . ● Never change tires when the vehicle is on a slope, ice or slippery areas. This is hazardous. ● Never change tires if oncoming traffic is close to your vehicle. Wait for profes- sional road[...]

T urn the clamp to remove the spare tire. Remove the spare tire. Removing the bolt-on wheel cover (if so equipped) CAUTION Do not use your hands to pry off wheel caps or wheel covers. Doing so could re- sult in personal injury. The wheel covers are held on by the wheel nuts. The wheel cover will be removed along with the wheel when the nuts are rem[...]

Jacking up vehicle and removing the damaged tire WARNING ● Never get under the vehicle while it is supported only by the jack. If it is nec- essary to work under the vehicle, sup- port it with safety stands. ● Use only the jack provided with your vehicle to lift the vehicle. Do not use the jack provided with your vehicle on other vehicles. The [...]

Always refer to the proper illustrations for the correct placement and jack -up points for your specific vehicle model and jack type. Carefully read the caution label attached to the jack body and the following instruc- tions. 1. Loosen each wheel nut one or two turns by turning counterclockwise with the wheel nut wrench. Do not remove the wheel nu[...]

4. Lower the vehicle slowly until the tire touches the ground. Then, with the wheel nut wrench, tighten the wheel nuts securely in the sequence illustrated ( s A , s B , s C , s D , s E ) . Lower the vehicle completely. WARNING ● Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to become loose or come off. This could ca[...]

● Whenever working on or near a battery, always wear suitable eye protectors (for example, goggles or industrial safety spectacles) and remove rings, metal bands, or any other jewelry. Do not lean over the battery when jump starting. ● Do not attempt to jump start a frozen battery. It could explode and cause se- rious injury. ● Y our vehicle [...]

CAUTION ● Always connect positive ( 1 ) to positive ( 1 ) and negative ( 2 ) to body ground (for example, strut mounting bolt, engine lift bracket, etc .) — not to the battery. ● Make sure the jumper cables do not touch moving parts in the engine com- partment and that the cable clamps do not contact any other metal. 5. Start the engine of th[...]

3. Get out of the vehicle. Look and listen for steam or coolant escaping from the radiator before opening the hood. (If steam or cool- ant is escaping, turn off the engine.) Do not open the hood further until no steam or coolant can be seen. 4. Open the engine hood. WARNING If steam or water is coming from the en- gine, stand clear to prevent getti[...]

For information about towing your vehicle behind a recreational vehicle (RV) , refer to “Flat towing” in the “T echnical and consumer information” sec- tion of this manual. T OWING RECOMMENDED BY NISSAN NISSAN recommends that your vehicle be towed with the driving (front) wheels off the ground or place the vehicle on a flat bed truck as ill[...]

CAUTION ● Never tow Continuously V ariable T rans- mission (CVT) models with the front wheels on the ground or four wheels on the ground (forward or backward) , as this may cause serious and expensive damage to the transmission. If it is nec- essary to tow the vehicle with the rear wheels raised always use towing dollies under the front wheels. ?[...]

WARNING ● Stand clear of a stuck vehicle. ● Do not spin your tires at high speed. This could cause them to explode and result in serious injury. Parts of your vehicle could also overheat and be damaged. CAUTION ● T ow chains or cables must be attached only to the main structural members of the vehicle. Otherwise, the vehicle body will be dama[...]

6-14 In case of emergency MEMO[...]

7 Appearance and care Cleaning exterior ..................................7 - 2 W ashing ......................................7 - 2 W axing ........................................7 - 2 Removing spots ................................7 - 3 Underbody ....................................7 - 3 Glass .........................................7 - 3 Alumi[...]

In order to maintain the appearance of your ve- hicle, it is important to take proper care of it. T o protect the paint surfaces, please wash your vehicle as soon as you can: ● after a rainfall to prevent possible damage from acid rain. ● after driving on coastal roads. ● when contaminants such as soot, bird drop- pings, tree sap, metal parti[...]

REMOVING SPOTS Remove tar and oil spots, industrial dust, insects, and tree sap as quickly as possible from the surface of the paint to avoid lasting damage or staining. Special cleaning products are available at a NISSAN dealer or any automotive accessory store. UNDERBODY In areas where road salt is used in winter, it is necessary to clean the und[...]

● Do not apply wheel cleaners to the wheels when they are hot. The wheel temperature should be the same as am- bient temperature. ● Rinse the wheel to completely remove the cleaner within 15 minutes after the cleaner is applied. CHROME PARTS Clean all chrome parts regularly with a non- abrasive chrome polish to maintain the finish. TIRE DRESSIN[...]

CAUTION ● Never use benzine, thinner or any simi- lar material. ● Small dirt particles can be abrasive and damaging to leather surfaces and should be removed promptly. Do not use saddle soap, car waxes, polishes, oils, cleaning fluids, solvents, deter- gents or ammonia-based cleaners as they may damage the leather’s natural finish. ● Never [...]

SEAT BELTS The seat belts can be cleaned by wiping them with a sponge dampened in a mild soap solution. Allow the belts to dry completely in the shade before using them. See “Seat belt maintenance” in the “Safety – Seats, seat belts and supplemen- tal restraint system” section of this manual. WARNING Do not allow wet seat belts to roll up[...]

CAUTION ● NEVER remove dirt, sand or other de- bris from the passenger compartment by washing it out with a hose. Remove dirt with a vacuum cleaner or broom. ● Never allow water or other liquids to come in contact with electronic compo- nents inside the vehicle as this may damage them. Chemicals used for road surface de-icing are extremely corr[...]

7-8 Appearance and care MEMO[...]

8 Maintenance and do-it-yourself Maintenance requirements ..........................8 - 2 General maintenance ..............................8 - 2 Explanation of general maintenance items .........8 - 2 Maintenance precautions ...........................8 - 5 Engine compartment check locations ................8 - 6 Engine cooling system ............[...]

Y our NISSAN has been designed to have mini- mum maintenance requirements with long ser- vice intervals to save you both time and money . However, some day-to-day and regular mainte- nance is essential to maintain your NISSAN’s good mechanical condition, as well as its emis- sions and engine performance. It is the owner’s responsibility to make[...]

When driving in areas using road salt or other corrosive materials, check lubrication frequently . Lights* Clean the headlights on a regular basis. Make sure that the headlights, stop lights, tail lights, turn signal lights, and other lights are all operating properly and installed securely . Also check headlight aim. Road wheel nuts (lug nuts)* Wh[...]

and are installed securely . Check the belt web- bing for cuts, fraying, wear or damage. Steering wheel Check for changes in the steer- ing system, such as excessive freeplay , hard steering or strange noises. Warning lights and chimes Make sure all warning lights and chimes are operating properly . Windshield wiper and washer* Check that the wiper[...]

When performing any inspection or maintenance work on your vehicle, always take care to prevent serious accidental injury to yourself or damage to the vehicle. The following are general precau- tions which should be closely observed. WARNING ● Park the vehicle on a level surface, ap- ply the parking brake securely and block the wheels to prevent [...]

QR25DE engine 1. P ower steering fluid reservoir 2. Engine oil filler cap 3. Brake fluid reservoir/Clutch fluid reservoir (M/T model) 4. Air cleaner 5. Fuse block 6. Battery 7. Fuse/Fusible link box 8. Engine oil dipstick 9. Radiator cap 10. Drive belt location 11. Engine coolant reservoir 12. Windshield washer fluid reservoir LDI0553 ENGINE COMPAR[...]

VQ35DE engine 1. P ower steering fluid reservoir 2. Engine oil filler cap 3. Brake fluid reservoir/Clutch fluid reservoir (M/T model) 4. Air cleaner 5. Fuse block 6. Battery 7. Fuse/Fusible link box 8. Engine oil dipstick 9. Radiator cap 10. Drive belt location 11. Engine coolant reservoir 12. Windshield washer fluid reservoir LDI0552 Maintenance a[...]

The engine cooling system is filled at the factory with Genuine NISSAN Long Life Antifreeze/Coolant to provide year-round anti- freeze and coolant protection. The anti-freeze solution contains rust and corrosion inhibitors. Additional engine cooling system additives are not necessary . WARNING ● Never remove the radiator or coolant reservoir cap [...]

CHANGING ENGINE COOLANT A NISSAN dealer can change the engine coolant. The service procedure can be found in the NISSAN Service Manual. Improper servicing can result in reduced heater performance and engine overheat- ing. WARNING ● T o avoid the danger of being scalded, never change the coolant when the en- gine is hot. ● Never remove the radia[...]

5. Remove the dipstick again and check the oil level. It should be between the H (High) and L (Low) marks s B . This is the normal oper- ating oil level range. If the oil level is below the L (Low) mark s A , remove the oil filler cap and pour recommended oil through the opening. Do not overfill s C . 6. Recheck oil level with the dipstick. It is n[...]

5. Remove the drain plug s B with a wrench by turning it counterclockwise and completely drain the oil. If the oil filter is to be changed, remove and replace it at this time. See “Changing engine oil filter” later in this section. ● Waste oil must be disposed of prop- erly. ● Check your local regulations. WARNING ● Prolonged and repeated[...]

CHANGING ENGINE OIL FILTER 1. Park the vehicle on a level surface and apply the parking brake. 2. T urn the engine off. 3. Place a large drain pan under the oil filter s A . 4. Loosen the oil filter s A with an oil filter wrench by turning it counterclockwise. Then remove the oil filter by turning it by hand. CAUTION Be careful not to burn yourself[...]

CAUTION ● Use only Genuine NISSAN CVT Fluid NS-2-V . Do not mix with other fluids. ● Using transmission fluid other than Genuine NISSAN CVT Fluid NS-2-V will damage the CVT , which is not covered by the NISSAN new vehicle limited warranty. When checking or replacement of CVT Fluid is required, we recommend your NISSAN dealer for servicing. The [...]

For further brake and clutch fluid specification information, refer to “Capacities and recom- mended fuel/lubricants” in the “T echnical and consumer information” section of this manual. WARNING ● Use only new fluid from a sealed con- tainer. Old, inferior or contaminated fluid may damage the brake and clutch systems. The use of improper [...]

WINDOW WASHER FLUID RESERVOIR Fill the window washer fluid reservoir periodically . Add window washer fluid when the low window washer fluid warning light comes on. T o fill the window washer fluid reservoir, lift the cap off the reservoir tank and pour the window washer fluid into the tank opening. Add a washer solvent to the washer for better cle[...]

● Do not operate the vehicle if the fluid in the battery is low. Low battery fluid can cause a higher load on the battery which can generate heat, reduce bat- tery life, and in some cases lead to an explosion. ● When working on or near a battery, al- ways wear suitable eye protection and remove all jewelry. ● Battery posts, terminals and rela[...]

V ehicles operated in high temperatures or under severe conditions require frequent checks of the battery fluid level. JUMP STARTING If jump starting is necessary , see “Jump starting” in the “In case of emergency” section of this manual. If the engine does not start by jump starting, the battery may have to be replaced. Contact a NISSAN de[...]

1. P ower steering fluid pump 2. Generator 3. Air conditioner 4. Crank pulley REPLACING SPARK PLUGS Iridium-tipped spark plugs (if so equipped) It is not necessary to replace iridium-tipped s A spark plugs as frequently as conventional type spark plugs because they last much longer. Fol- low the maintenance log shown in the “NISSAN Service and Ma[...]

The air cleaner filter should not be cleaned and reused. Replace it according to the maintenance log shown in the “NISSAN Service and Mainte- nance Guide.” When replacing the filter, wipe the inside of the air cleaner filter housing and the cover with a damp cloth. T o remove the air cleaner filter, push the tabs and pull the unit upward. WARNI[...]

CLEANING If your windshield is not clear after using the windshield washer or if a wiper blade chatters when running, wax or other material may be on the blade or windshield. Clean the outside of the windshield with a washer solution or a mild detergent. Y our windshield is clean if beads do not form when rinsing with clear water. Clean each blade [...]

If you wax the surface of the hood, be careful not to let wax get into the washer nozzle s A . This may cause clogging or improper windshield washer operation. If wax gets into the nozzle, remove it with a needle or small pin s B . If the brakes do not operate properly , have the brakes checked by a NISSAN dealer. SELF-ADJUSTING BRAKES Y our vehicl[...]

T wo types of fuses are used. T ype s A is used in the fuse boxes in the engine compartment. T ype s B is used in the passenger compartment fuse box. T ype A fuses are provided as spare fuses. They are stored in the passenger compartment fuse box. T ype A fuses can be installed in the engine com- partment and passenger compartment fuse boxes. If a [...]

3. Remove the fuse box cover by pushing the tab and lifting the cover up. 4. Remove the fuse with the fuse puller. The fuse puller is located in the center of the fuse block in the passenger compartment. 5. If the fuse is open s A , replace it with a new fuse s B . 6. If a new fuse also opens, have the electrical system checked and repaired by a NI[...]

PASSENGER COMPARTMENT CAUTION Never use a fuse of a higher or lower amperage rating than specified on the fuse box cover. This could damage the electrical system or cause a fire. If any electrical equipment does not operate, check for an open fuse. 1. Be sure the ignition switch and the headlight switch are OFF . 2. Pull the fuse box cover to remov[...]

CAUTION Be careful not to allow children to swallow the battery or removed parts. T ype B LDI0456 WDI0567 BATTERY REPLACEMENT Maintenance and do-it-yourself 8-25 Z REVIEW COPY— 2009 Altima (alt) Owners Manual (owners) —USA_English (nna) 02/03/09—debbie X[...]

NISSAN INTELLIGENT K EY™ Replace the battery in the Intelligent K ey as fol- lows: 1. Remove the mechanical key from the Intelli- gent K ey . 2. Insert a small screwdriver s A into the slit s B of the corner and twist it to separate the upper part from the lower part. Use a cloth to protect the casing. 3. Replace the battery with a new one. Recom[...]

HEADLIGHTS Replacing the xenon headlight bulb (if so equipped) WARNING c HIGH VOL T AGE When xenon headlights are on, they pro- duce a high voltage. T o prevent an electric shock, never attempt to modify or disas- semble. Always have your xenon head- lights replaced at a NISSAN dealer. For additional information, see “Headlight and turn signal sw[...]

EXTERIOR AND INTERIOR LIGHTS Item W attage (W) Bulb No.* 1 Headlight assembly * 2 Low (Halogen) 55 H11 Low (Xenon) 35 D2R High 65 H9 Park 8 168 T urn 27 3457NAK Sidemarker Sedan 5 168 Coupe 5 W5W Front fog light (if so equipped) * 2 55 H11 Step light — 194 Rear combination light T ail/Stop 8/27 3157K T urn 27 3156 Backup (reversing) Sedan 18 921 [...]

Coupe 1. Mirror-mounted turn signal light (if so equipped) 2. Interior light 3. Map light 4. Headlamp assembly 5. Fog light (if so equipped) 6. Step light 7. High-mount stoplight 8. T runk light 9. License plate light 10. Rear combination light WDI0626 Maintenance and do-it-yourself 8-29 Z REVIEW COPY— 2009 Altima (alt) Owners Manual (owners) —[...]

Sedan 1. Rear map light 2. Front map light 3. Step light 4. Headlamp assembly 5. Fog light (if so equipped) 6. High-mount stoplight (if so equipped) 7. T runk light 8. Spoiler mounted stoplight (if so equipped) 9. Rear combination light 10. License plate light 11. Mirror-mounted turn signal light (if so equipped) WDI0680 8-30 Maintenance and do-it-[...]

Replacement procedures All other lights are either type A , B, C or D. When replacing a bulb, first remove the lens, light and/or cover. Indicates bulb removal Indicates bulb installation Use a cloth s 1 to protect the housing. WDI0306 Step light LDI0341 Maintenance and do-it-yourself 8-31 Z REVIEW COPY— 2009 Altima (alt) Owners Manual (owners) ?[...]

Use a cloth s 1 to protect the housing. Use a cloth s 1 to protect the housing. Map light LDI0571 Interior light WDI0632 8-32 Maintenance and do-it-yourself Z REVIEW COPY— 2009 Altima (alt) Owners Manual (owners) —USA_English (nna) 02/03/09—debbie X[...]

Rear combination light T o access the bulbs in the rear combination light: s 1 Remove the fasteners. Carefully push back the carpet. s 2 Remove the 2 nuts and pull out the rear combination light. s 3 Rotate the bulb(s) counterclockwise and pull out to remove: s A T urn signal light s B Sidemarker light s C T ail/stop light s D Backup light WDI0635 [...]

If you have a flat tire, see “Flat tire” in the “In case of emergency” section of this manual. TIRE PRESSURE Tire Pressure Monitoring System (TPMS) This vehicle is equipped with the Tire Pressure Monitoring System (TPMS) . It monitors tire pressure of all tires except the spare. When the low tire pressure warning light is lit, one or more o[...]

Incorrect tire pressure, including un- der inflation, may adversely affect tire life and vehicle handling. WARNING ● Improperly inflated tires can fail suddenly and cause an accident. ● The Gross V ehicle Weight Rating (GVWR) is located on the F .M .V.S.S./C.M .V.S.S. certifica- tion label. The vehicle weight ca- pacity is indicated on the Tire[...]

Tire and loading information label s 1 Seating capacity: The maximum num- ber of occupants that can be seated in the vehicle. s 2 V ehicle load limit: See loading infor- mation in the “T echnical and con- sumer information” section. s 3 Original tire size: The size of the tires originally installed on the vehicle at the factory . s 4 Cold tire [...]

Checking tire pressure 1. Remove the valve stem cap from the tire. 2. Press the pressure gauge squarely onto the valve stem. Do not press too hard or force the valve stem side- ways, or air will escape. If the hissing sound of air escaping from the tire is heard while checking the pressure, reposition the gauge to eliminate this leakage. 3. Remove [...]

Size Cold Tire Inflation Pres- sure Front Original Tire P215/60/R16 220 kPa, 32 PSI P215/55R17 230 kPa, 33 PSI P235/45R18 Rear Original Tire P215/60R16 220 kPa, 32 PSI P215/55R17 230 kPa, 33 PSI P235/45R18 Spare Tire T135/70R16 T135/90R16 420 kPa, 60 PSI TIRE LABELING Federal law requires tire manufacturers to place standardized information on the [...]

s 1 Tire size (example: P215/65R15 95H) 1. P: The “P” indicates the tire is de- signed for passenger vehicles (not all tires have this information) . 2. Three-digit number (215): This num- ber gives the width in millimeters of the tire from sidewall edge to side- wall edge. 3. T wo-digit number (65): This number, known as the aspect ratio, give[...]

s 2 TIN (Tire Identification Number) for a new tire (example: DO T XX XX XXX XXXX) 1. DO T : Abbreviation for the “Depart- ment Of T ransportation” . The symbol can be placed above, below or to the left or right of the Tire Identification Number. 2. T wo-digit code: Manufacturer’s identification mark. 3. T wo-digit code: Tire size. 4. Three-d[...]

s 7 The word “radial” The word “radial” is shown if the tire has radial structure. s 8 Manufacturer or brand name Manufacturer or brand name is shown. Other Tire-related T erminology In addition to the many terms that are defined throughout this section, Intended Outboard Sidewall is (1) the sidewall that contains a whitewall, bears white l[...]

studded tires. Skid and traction capabilities of studded snow tires on wet or dry surfaces may be poorer than that of non-studded snow tires. TIRE CHAINS CAUTION Only certain SAE class “S” tire chains can be used on this vehicle. Using the wrong Class “S” chains on this vehicle will cause damage to the vehicle. If you plan to use tire chain[...]

CHANGING WHEELS AND TIRES Tire rotation NISSAN recommends rotating the tires every 7,500 miles (12,000 km) . See “Flat tire” in the “In case of emer- gency” section of this manual for tire re- placing procedures. As soon as possible, tighten the wheel nuts to the specified torque with a torque wrench. Wheel nut tightening torque: 83 ft-lb ([...]

● The original tires have built-in tread wear indicators. When the wear indicators are visible, the tire(s) should be replaced. ● Tires degrade with age and use. Have tires, including the spare, over 6 years old checked by a qualified technician because some tire damage may not be ob- vious. Replace the tires as neces- sary to prevent tire fail[...]

● Do not install a damaged or deformed wheel or tire even if it has been re- paired. Such wheels or tires could have structural damage and could fail with- out warning. ● The use of retread tires is not recommended. ● For additional information regarding tires, refer to “Important Tire Safety In- formation” (US) or “Tire Safety Informa-[...]

● Tire tread of the TEMPORAR Y USE ONL Y spare tire will wear at a faster rate than the standard tire. Replace the spare tire as soon as the tread wear indicators appear. ● Do not use the spare tire on other vehicles. ● Do not use more than one spare tire at the same time. ● Do not tow a trailer when the TEMPO- RAR Y USE ONL Y spare tire is[...]

9 T echnical and consumer information Capacities and recommended fuel/lubricants .........9 - 2 Fuel recommendation ...........................9 - 3 Engine oil and oil filter recommendations ..........9 - 5 Air conditioner system refrigerant and oil recommendations ..............................9 - 6 Specifications .................................[...]

The following are approximate capacities. The actual refill capacities may be slightly different. When refilling, follow the procedure described in the “Maintenance and do-it-yourself” section to determine the proper refill capacity. Capacity (Approximate) Recommended Fluids and Lubricants US measure Imp measure Liter Fuel 20 gal 16-5/8 gal 75.[...]

FUEL RECOMMENDATION For 2.5L engine Use unleaded regular gasoline with an octane rating of at least 87 AKI (Anti-Knock Index) num- ber (Research octane number 91) . For 3.5L engine NISSAN recommends the use of premium un- leaded gasoline with an octane rating of at least 91 AKI (Anti-Knock Index) number (Research octane number 96) . If unleaded pre[...]

If any driveability problems such as engine stall- ing and difficult hot-starting are experienced after using oxygenate-blend fuels, immediately change to a non-oxygenate fuel or a fuel with a low blend of MTBE. T ake care not to spill gasoline during refu- eling. Gasoline containing oxygenates can cause paint damage. E–85 fuel E-85 fuel is a mix[...]

ENGINE OIL AND OIL FILTER RECOMMENDATIONS Selecting the correct oil It is essential to choose the correct grade, quality and viscosity engine oil to ensure satisfactory engine life and performance. See “Capacities and recommended fuel/lubricants” earlier in this section. NISSAN recommends the use of an energy conserving oil in order to improve [...]

Y our engine was filled with a high-quality engine oil when it was built. Y ou do not have to change the oil before the first recommended change interval. Oil and filter change intervals depend upon how you use your vehicle. Operation under the following conditions may require more frequent oil and filter changes: ● repeated short distance drivin[...]

ENGINE Model QR25DE VQ35DE T ype Gasoline, 4-cycle, DOHC Gasoline, 4-cycle, DOHC Cylinder arrangement 4-cylinder in-line 6-cylinder, V-block, Slanted at 60° Bore x Stroke in (mm) 3.5 x 3.9 (89.0 x 100.0) 3.760 x 3.205 (95.5 x 81.4) Displacement cu in (cm 3 ) 151.82 (2,488) 213.45 (3,498) Firing order 1–3–4–2 1–2–3–4–5–6 Idle speed [...]

WHEELS AND TIRES Wheel type Size Offset in (mm) Aluminum/Steel 16 x 7JJ 1.77 (45) Aluminum 17 x 7 1/2JJ 1.77 (45) Aluminum 18 x 7.5JJ 1.77 (45) T type (Spare) 16 x 4T 1.77 (45) Tire size P215/60R16 P215/55R17 P235/45R18 Spare tire T135/70R16 T135/90R16 DIMENSIONS AND WEIGHTS Coupe Sedan Overall length in (mm) 182.5 (4,636) 189.8 (4,820) Overall wid[...]

When planning to drive your NISSAN ve- hicle in another country, you should first find out if the fuel available is suitable for your vehi- cle’s engine. Using fuel with an octane rating that is too low may cause engine damage. All gasoline vehicles must be operated with unleaded gasoline. There- fore, avoid taking your vehicle to areas where app[...]

ENGINE SERIAL NUMBER The number is stamped on the engine as shown. F .M.V .S.S./C.M.V .S.S. CERTIFICATION LABEL The Federal/Canadian Motor V ehicle Safety Standard (F .M.V .S.S./C.M.V .S.S.) certification la- bel is affixed as shown. This label contains valu- able vehicle information, such as: Gross V ehicle W eight Ratings (GVWR) , Gross Axle Weig[...]

EMISSION CONTROL INFORMATION LABEL The emission control information label is at- tached to the underside of the hood as shown. TIRE AND LOADING INFORMATION LABEL The cold tire pressure is shown on the Tire and Loading Information label. The label is located as shown. AIR CONDITIONER SPECIFICATION LABEL The air conditioner specification label is aff[...]

Use the following steps to mount the front license plate: s 1 Make a shallow hole in each plastic finisher at the location mark (small dimple) using a 0.31 in (8 mm) drill. T o avoid damaging the threads behind the finisher, apply only light pressure to the drill. s 2 Mount the license plate bracket using two 8 mm slotted hex head screws. WARNING ?[...]

● GVW (Gross V ehicle W eight) - curb weight plus the combined weight of passengers and cargo. ● GVWR (Gross V ehicle W eight Rat- ing) - maximum total combined weight of the unloaded vehicle, pas- sengers, luggage, hitch, trailer tongue load and any other optional equipment. This information is lo- cated on the F .M.V .S.S./C.M.V .S.S. certifi[...]

Steps for determining correct load limit 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3. Subtract the combined weight of the driver and passengers from XXX [...]

5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4. 6. If your vehicle will be towing a trailer, load from your trailer will be trans- ferred to your vehicle. Consult this manual to determine how this re- duces the av[...]

WARNING Overloading or improper loading of a trailer and its cargo can adversely affect vehicle handling, braking and perfor- mance and may lead to accidents. CAUTION ● Do not tow a trailer or haul a heavy load for the first 500 miles (800 km) . Y our engine, axle or other parts could be damaged. ● For the first 500 miles (800 km) that you tow [...]

T emperature conditions can also affect towing. For example, towing a heavy trailer in high outside temperatures on graded roads can affect engine performance and cause overheating. The engine protection mode, which helps reduce the chance of engine damage, could activate and automati- cally decrease engine power. V ehicle speed may decrease under [...]

T owing capacities are calculated assuming a base vehicle with driver and any options required to achieve the rating. Additional passengers, cargo and/or optional equipment, such as the trailer hitch, will add weight to the vehicle and reduce your vehicle’s maximum towing capacity and trailer tongue load. The vehicle and trailer need to be weighe[...]

Always verify that available capacities are within the required ratings. T OWING LOAD/SPECIFICATION T OWING LOAD / SPECIFICA TION UNIT : lb (kg) MAXIMUM T OWING L OAD 1,000 (454) MAXIMUM T ONGUE L OAD 100 (45) T OWING SAFETY T railer hitch Choose a proper hitch for your vehicle and trailer. Make sure the trailer hitch is securely attached to the ve[...]

Y ou may add Class I trailer hitch equipment that has a 2,000 lb (909 kg) maximum weight rating to the vehicle, but your vehicle is only capable of towing the maximum trailer weights shown in the T owing Load/Specification Chart earlier in this section. CAUTION ● Do not use axle-mounted hitches. ● The hitch should not be attached to or affect t[...]

WARNING Never connect a trailer brake system di- rectly to the vehicle brake system. When towing a trailer load of 3,500 lbs. (1587 kg) or more, trailers with a brake system MUST be used. However, most states require a separate braking system on trailers with a loaded weight above a specific amount. Make sure the trailer meets the local regulations[...]

● Always drive your vehicle at a moderate speed. ● When backing up, hold the bottom of the steering wheel with one hand. Move your hand in the direction in which you want the trailer to go. Make small corrections and back up slowly . If possible, have someone guide you when you are backing up. Always block the wheels on both vehicle and trailer[...]

2. When the trailer sway stops, gently apply the brakes and pull to the side of the road in a safe area. 3. T ry to rearrange the trailer load so it is bal- anced as described earlier in this section. ● Be careful when passing other vehicles. Passing while towing a trailer requires con- siderably more distance than normal pass- ing. Remember, the[...]

Manual T ransmission ● Always tow with the manual transmission in Neutral. ● After towing 500 miles (805 km) , start and idle the engine with the transmission in Neu- tral for two minutes. Failure to idle the engine after every 500 miles (805 km) of towing may cause damage to internal transmission parts. DO T (Department of T ransportation) Qua[...]

WARNING The temperature grade for this tire is es- tablished for a tire that is properly inflated and not overloaded. Excessive speed, under-inflation, or excessive loading, ei- ther separately or in combination, can cause heat build-up and possible tire failure. Y our NISSAN vehicle is covered by the following emission warranties: For USA 1. Emiss[...]

Due to legal requirements in some states and Canadian Provinces, your vehicle may be re- quired to be in what is called the “ready condi- tion” for an Inspection/Maintenance (I/M) test of the emission control system. The vehicle is set to the “ready condition” when it is driven through certain driving patterns. Usually , the ready condition[...]

This vehicle is equipped with an Event Data Re- corder (EDR) . The main purpose of an EDR is to record, in certain crash or near crash-like situa- tions, such as an air bag deployment or hitting a road obstacle, data that will assist in understand- ing how a vehicle’s systems performed. The EDR is designed to record data related to vehicle dynami[...]

For Canada T o purchase a copy of a genuine NISSAN Ser- vice Manual or Owner’s Manual please contact your nearest NISSAN dealer. For the phone num- ber and location of a NISSAN dealer in your area call the NISSAN Information Center at 1-800- 387-0122 and a bilingual NISSAN representa- tive will assist you. Also available are genuine NISSAN Servic[...]

10 Index A Air bag (See supplemental restraint system) .................... .1-43 Air bag system Front (See supplemental front impact air bag system) .............. .1-52 Air bag warning light .......... .1-58, 2-14 Air cleaner housing filter ........... .8-19 Air conditioner Air conditioner operation ......... .4-13 Air conditioner service .......[...]

Clock ............ .4-5, 4-28, 4-32, 4-38 (models with navigation system) ..... .4-5 (models without navigation system) ............... .4-28, 4-32 Clock set ............. .4-5, 4-28, 4-32 Clutch Clutch fluid ................ .8-14 C.M.V .S.S. certification label ......... .9-10 Cold weather driving ............. .5-27 Compact disc (CD) player ....[...]

F .M.V .S.S. certification label ......... .9-10 Fog light switch ................ .2-33 Front air bag system (See supplemental restraint system) .... .1-52 Front seats ................... .1-2 Fuel Capacities and recommended fuel/lubricants ................ .9-2 Fuel economy ............... .5-21 Fuel gauge ................. .2-6 Fuel octane ratin[...]

V ehicle identification number (VIN) plate . .9-9 W arning labels (for SRS) ......... .1-58 Language setting ................ .4-6 LA TCH (Lower Anchors and T ethers for CHildren) System ............. .1-25 License plate Installing the license plate ........ .9-12 Light Air bag warning light ........ .1-58, 2-14 Brake light (See stop light) .......[...]

Rear power windows ........... .2-45 Precautions Maintenance precautions ......... .8-5 Precautions on child restraints ........... .1-23, 1-33, 1-39 Precautions on seat belt usage ..... .1-15 Precautions on supplemental restraint system ................... .1-43 Precautions when starting and driving . . .5-2 Programmable features ............ .4-3[...]

Switch Autolight switch .............. .2-30 Automatic power window switch .... .2-45 Fog light switch .............. .2-33 Hazard warning flasher switch ...... .2-33 Headlight and turn signal switch ..... .2-29 Headlight control switch ......... .2-29 Power door lock switch .......... .3-5 Rear window and outside mirror defroster switch ..........[...]

W arning labels (for SRS) ......... .1-58 W arning/indicator lights and audible reminders ................. .2-10 W arning lights ................. .2-10 W asher switch Windshield wiper and washer switch . . .2-27 W eights (See dimensions and weights) . . . .9-8 Wheels and tires ............... .8-34 Wheel/tire size ................. .9-8 When trav[...]

RECOMMENDED FUEL: For 2.5L engine Use unleaded regular gasoline with an octane rating of at least 87 AKI (Anti-Knock Index) num- ber (Research octane number 91) . For 3.5L engine NISSAN recommends the use of premium un- leaded gasoline with an octane rating of at least 91 AKI (Anti-Knock Index) number (Research octane number 96) . If unleaded premi[...]

200 9 N I S S AN AL TI MA 200 9 AL TI MA OWN E R'S MAN UAL L3 2-D Printing : May 2009 ( 1 0) Publication No.: OM9E-0L3 2U2 Printed in U.S.A. F or your saf et y , read car efully and k eep in this v ehicle. L3 2-D[...]