Go to page of
A good user manual
The rules should oblige the seller to give the purchaser an operating instrucion of Omega Engineering CN 79000, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.
What is an instruction?
The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Omega Engineering CN 79000 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.
Unfortunately, only a few customers devote their time to read an instruction of Omega Engineering CN 79000. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.
What should a perfect user manual contain?
First and foremost, an user manual of Omega Engineering CN 79000 should contain:
- informations concerning technical data of Omega Engineering CN 79000
- name of the manufacturer and a year of construction of the Omega Engineering CN 79000 item
- rules of operation, control and maintenance of the Omega Engineering CN 79000 item
- safety signs and mark certificates which confirm compatibility with appropriate standards
Why don't we read the manuals?
Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Omega Engineering CN 79000 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Omega Engineering CN 79000, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Omega Engineering service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Omega Engineering CN 79000.
Why one should read the manuals?
It is mostly in the manuals where we will find the details concerning construction and possibility of the Omega Engineering CN 79000 item, and its use of respective accessory, as well as information concerning all the functions and facilities.
After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.
Table of contents for the manual
-
Page 1
omega.com e-mail: info@omega.com For latest product manuals: omegamanual.info Series CN 79000 U ser ’ s Guide Shop online at[...]
-
Page 2
Servicing Nor th America: U.S.A.: One Omega Drive, Box 4047 ISO 9001 Certified Stamford, CT 06907-0047 T el: (203) 359-1660 F AX: (203) 359-7700 e-mail: info@omega.com Canada: 976 Bergar Laval (Quebec) H7L 5A1, Canada T el: (514) 856-6928 F AX: (514) 856-6886 e-mail: info@omega.ca For immediate technical or application assistance: U.S.A. and Canada[...]
-
Page 3
INSTRUCTIONS FOR THE CN79000 SERIES 1/32 DIN DUAL ZONE MICROPROCESSOR BASED TEMPERA TURE/PROCESS CONTROL OMEGA Engineering One Omega Drive Stamford, Connecticut 06907-0047 P .O. Box 4047 T elephone: 800/848-4286; 203/359-1660 Fax: 203/359-7700[...]
-
Page 4
Page 2 of 40 Contents INSTALLATION ....................................................................................... 3 WIRING ................................................................................................... 5 Wiring for Optional Inputs and Outputs ................................................... 6 Wiring for 4 to 20mA Tr[...]
-
Page 5
MODEL IDENTIFICA TION CN790 Output A 2 = Switched V oltage 5 VDC 3 = Relay Output 2 = Switched V oltage 5VDC 3 = Relay Options C4 = RS485 L V = Low V oltage[...]
-
Page 6
Page 4 of 40 From the front of the panel, slide the housing through the cutout. The housing gasket should be flat against the housing flange before installing. From the rear of the panel slide the mounting collar over the housing. Hold the housing with one hand and using the other hand, push the collar evenly against the panel until the spring loop[...]
-
Page 7
[...]
-
Page 8
Page 6 of 40 Wiring for Optional Inputs and Outputs Wire power and outputs as shown. Wiring for options is shown below. All wiring shown below is Class 2. Shielded twisted pair is required for Option C4 . 5 6 Option 992: T er minal 5 is line A (-). T erminal 6 is line B (+). Last control in chain must hav e 120 ohm ± 1% resistor across 5 and 6. Op[...]
-
Page 9
Page 7 of 40 Wiring for 4 to 20mA Transmitter inputs External Po wer Supply 24 Vdc + - T ransmitter + - Wiring for Z1 Input External Po wer Supply 24 Vdc + - T ransmitter + - Wiring for Z2 Input DO NOT WIRE THE 24 VOLT POWER SUPPLY ACROSS THE INPUT OF THE CONTROL. DAMAGE TO THE INSTRUMENT INPUT CIRCUITRY WILL RE- SULT. WARNING: The inputs of the in[...]
-
Page 10
[...]
-
Page 11
Page 9 of 40 SECURITY LEVEL SELECTION Four levels of security are provided. The display shows the current security level. To change security levels change the password value using the UP ARROW and DOWN ARROW keys and pressing the ENTER key. Refer to the password table (following) for the correct value to enter for the security level desired. The SE[...]
-
Page 12
The home display is the normal display while the control is operating. If no errors or functions are active, the HOME display will indicate the Process V ariable for Set Point 1 on the top display and the Process variable for Set Point 2 on the bottom.[...]
-
Page 13
Page 11 of 40 PROGRAMMING SET POINTS FOR ALARM FUNCTIONS Caution: In any critical application where failure could cause expensive product loss or endanger personal safety, a redundant limit controller is required. The C N 74000 Series allows Zone 1 and / or Zone 2 to operate as limit or alarm type outputs. This function is available on both outputs[...]
-
Page 14
Page 12 of 40 OPERATION OF SELF TUNE® FUNCTION Self Tune® allows automatic selection of the necessary parameters to achieve best control operation from your C N 74000 Series control. If you are using the control output as a simple on-off function (e.g. Out1 Out1 Out1 Out1 Out1 set for OnOF OnOF OnOF OnOF OnOF ), none of the following will apply. [...]
-
Page 15
Page 13 of 40 The calculations for the PID values are the same as used in the standard Ziegler - Nichols equations that have been recognized as standard for decades. The only modification to the application of the Ziegler - Nichols equations is controlled by the dFC1 dFC1 dFC1 dFC1 dFC1 and dfC2 dfC2 dfC2 dfC2 dfC2 menu items. These menu items cont[...]
-
Page 16
Page 14 of 40 FACTORY DEFAULT PROCEDURE If for any reason you wish to restore the factory settings use the following procedure. 1. Turn off power to control 2. Turn on power to control 3. While control is performing SELF SELF SELF SELF SELF tESt tESt tESt tESt tESt , press and hold the INDEX and ENTER keys. 4. The control will display the ROM ID co[...]
-
Page 17
Page 15 of 40 SECONDARY MENU Hold UP ARROW & ENTER. Press INDEX to advance to the next menu item. Press UP ARROW or DOWN ARROW to change the value in the display. Press ENTER to retain the value. Edit Edit Edit Edit Edit Edit Set Point parameters: Select 0 , 1 , 2 , or 3 . 0 0 0 0 0 Edit function is off. 1 1 1 1 1 Edit Secondary and Secure Menu[...]
-
Page 18
Page 16 of 40 Power On, PEA2 is reset to the present input. To manually reset the value PEA2 PEA2 PEA2 PEA2 PEA2 must be in the lower display. Press the ENTER key to reset. PEA2 PEA2 PEA2 PEA2 PEA2 will be reset and display the present input value. UAL2 UAL2 UAL2 UAL2 UAL2 The Valley feature stores the lowest input the Instrument has measured for Z[...]
-
Page 19
age 17 of 40 If Edit Edit Edit Edit Edit is set to 1 1 1 1 1 or 3 3 3 3 3 , begin. If Edit Edit Edit Edit Edit is set to 2 2 2 2 2 , jump to Out2 Out2 Out2 Out2 Out2 on page 20. Out1 Out1 Out1 Out1 Out1 Output selection: Select OnOf OnOf OnOf OnOf OnOf , 1tP 1tP 1tP 1tP 1tP , or 1PuL 1PuL 1PuL 1PuL 1PuL . ONOF ONOF ONOF ONOF ONOF A setting of ONOF [...]
-
Page 20
Page 18 of 40 value of 1 provides an output of one sec- ond on and one second off (50% output). A pulse value of 2 provides an output of one second on and two seconds off (33% out- put). Output at center of band equals one second on, 2 (pulse value-1) seconds off. ProP ProP ProP ProP ProP For Current (Code 5) outputs only. tun1 tun1 tun1 tun1 tun1 [...]
-
Page 21
Page 19 of 40 OFF OFF OFF OFF OFF Reset Offset Value is retained in memory when the process input is not within the Proportional Band. Art1 Art1 Art1 Art1 Art1 Approach Rate Time: Select OFF OFF OFF OFF OFF , 0.01 0.01 0.01 0.01 0.01 to 99.99 99.99 99.99 99.99 99.99 minutes. The function defines the amount of Rate applied when the input is outside [...]
-
Page 22
Page 20 of 40 InC1 InC1 InC1 InC1 InC1 Input Correction: Select -500 -500 -500 -500 -500 to 500 500 500 500 500 °F, °C, or counts. This feature allows the input value to be changed to agree with an external reference or to compensate for sensor error. Note: InC1 is reset to zero when the input type is changed, or when decimal position is changed.[...]
-
Page 23
Page 21 of 40 If Edit Edit Edit Edit Edit is set to 1 1 1 1 1 , jump to LorE LorE LorE LorE LorE on page 24. If Edit Edit Edit Edit Edit is set to 3 3 3 3 3 , continue. If Edit Edit Edit Edit Edit is set to 2 2 2 2 2 , begin. Out2 Out2 Out2 Out2 Out2 Output selection: Select OnOf OnOf OnOf OnOf OnOf , 1tP 1tP 1tP 1tP 1tP , or 1PuL 1PuL 1PuL 1PuL 1P[...]
-
Page 24
Page 22 of 40 center of the proportional band, a pulse value of 1 provides an output of one sec- ond on and one second off (50% output). A pulse value of 2 provides an output of one second on and two seconds off (33% out- put). Output at center of band equals one second on, 2 (pulse value-1) seconds off. ProP For Current (Code 5) outputs only. tun2[...]
-
Page 25
Page 23 of 40 OFF OFF OFF OFF OFF Reset Offset Value is retained in memory when the process input is not within the Proportional Band. Art2 Art2 Art2 Art2 Art2 Approach Rate Time: Select OFF OFF OFF OFF OFF , 0.01 0.01 0.01 0.01 0.01 to 99.99 99.99 99.99 99.99 99.99 minutes. The function defines the amount of Rate applied when the input is outside [...]
-
Page 26
Page 24 of 40 InC2 InC2 InC2 InC2 InC2 Input Correction: Select -500 -500 -500 -500 -500 to 500 °F, °C, or counts. This feature allows the input value to be changed to agree with an external reference or to compensate for sensor error. Note: InC2 is reset to zero when the input type is changed, or when decimal position is changed. Fil2 Fil2 Fil2 [...]
-
Page 27
Page 25 of 40 address 17 17 17 17 17 and Zone 2 is assigned to address 18 18 18 18 18 ). To change this parameter, see Addr Addr Addr Addr Addr in the Secure Menu. SECURE MENU Hold UP ARROW & ENTER for 5 Seconds. Press INDEX to advance to the next menu item. Press UP ARROW or DOWN ARROW to change the value in the display. Press ENTER to retain [...]
-
Page 28
[...]
-
Page 29
Page 27 of 40 Note: If both Set Point 1 and Set Point 2 are set for temperature inputs, they must both be set for the same scale. While it is possible to set one input as degrees F and the other degrees C, as there is only one descriptor, one of the displays is likely to be mis-read. If one Set Point is set for process input, you may select to disp[...]
-
Page 30
Page 28 of 40 SCH1 SCH1 SCH1 SCH1 SCH1 Scale High: Select 100 to 9999 counts above SCL1 SCL1 SCL1 SCL1 SCL1 . The total span between SCL1 SCL1 SCL1 SCL1 SCL1 and SCH1 SCH1 SCH1 SCH1 SCH1 must be within 11998 counts. Maximum setting range is -1999 to + 9999 counts. Minimum span is 100 counts. For Current and Voltage inputs, this will set the high ra[...]
-
Page 31
Page 29 of 40 devices which do not have bias adjustments. Factory set to 100 100 100 100 100 for all output codes. If Out1 Out1 Out1 Out1 Out1 is set for ## tP tP tP tP tP , # PUL PUL PUL PUL PUL , or ProP ProP ProP ProP ProP ,then skip to S1LP S1LP S1LP S1LP S1LP . S1rE S1rE S1rE S1rE S1rE Set Point Reset. Select OnOF OnOF OnOF OnOF OnOF or Hold H[...]
-
Page 32
[...]
-
Page 33
Decimal Point Positioning: Select 0 0 , , 0 0 . . 0 0 . This will only ef fect the Process V alue, SP1, SP2, and InC1llnC2. 0 0 No decimal Point is selected. 0 0 . . 0 0 One decimal place is available for T ype J, K, E, T , L Inputs.[...]
-
Page 34
Page 32 of 40 SCH2 SCH2 SCH2 SCH2 SCH2 Scale High: Select 100 to 9999 counts above SCL2 SCL2 SCL2 SCL2 SCL2 . The total span between SCL2 and SCH2 must be within 11998 counts. Maximum setting range is -1999 to +9999 counts. Minimum span is 100 counts. For Current and Voltage inputs, this will set the high range end. Viewable only for Thermocouple a[...]
-
Page 35
Page 33 of 40 devices which do not have bias adjustments. Factory set to 100 100 100 100 100 for all output codes. If Out2 Out2 Out2 Out2 Out2 is set for ## tP tP tP tP tP , # PUL PUL PUL PUL PUL , or ProP ProP ProP ProP ProP ,then skip to S2LP S2LP S2LP S2LP S2LP . S2rE S2rE S2rE S2rE S2rE Set Point Reset. Select OnOF OnOF OnOF OnOF OnOF or Hold H[...]
-
Page 36
Page 34 of 40 The following Menu Items operate on the entire Instrument. There is no Set Point distinction. These items will appear in both the Edit1 Edit1 Edit1 Edit1 Edit1 , Edit2 Edit2 Edit2 Edit2 Edit2 , and Edit3 Edit3 Edit3 Edit3 Edit3 menus. SP1o SP1o SP1o SP1o SP1o Set Point 1 Output Select: Select OutA OutA OutA OutA OutA or Outb Outb Outb[...]
-
Page 37
Page 35 of 40 SPECIFICATIONS Input: Thermocouple . Input Impedance: Thermocouple = 3 megohms minimum. Sensor Break Protection: De-energizes control output to protect system after customer set time. (See InP1 and InP2 in Secondary Menu.) Set Point Range: Selectable (See Range Chart Page 39). Display: Two 4 digit, 7 segment 6.35 mm (0.25") high [...]
-
Page 38
Page 36 of 40 Storage Temperature: -40 to +80 °C (-40 to 176 °F). Humidity Conditions: 0 to 90% up to 40 °C non-condensing, 10 to 50% at 55 °C non-condensing. Memory Backup: Nonvolatile memory. No batteries required. Control Output Ratings: Relay (Output A, Output B): SPST, 3 A @ 240 Vac resistive; 1.5A @240 Vac inductive; 1/10 HP @ 120 Vac. Sw[...]
-
Page 39
Page 37 of 40 DISPLAY No display lighted FAIL FAIL FAIL FAIL FAIL tESt tESt tESt tESt tESt CHEC SP1 CHEC SP1 CHEC SP1 CHEC SP1 CHEC SP1 CHEC SP2 CHEC SP2 CHEC SP2 CHEC SP2 CHEC SP2 CHEC SPL1 CHEC SPL1 CHEC SPL1 CHEC SPL1 CHEC SPL1 CHEC SPH1 CHEC SPH1 CHEC SPH1 CHEC SPH1 CHEC SPH1 or CHEC SPL2 CHEC SPL2 CHEC SPL2 CHEC SPL2 CHEC SPL2 CHEC SPH2 CHEC S[...]
-
Page 40
[...]
-
Page 41
[...]
-
Page 42
OMEGA Engineering One Omega Drive Stamford, Connecticut 06907-0047 P .O. Box 4047 T elephone: 800/848-4286; 203/359-1660 Fax: 203/359-7700 FR# 08-195860-03[...]
-
Page 43
OME GA ENGINEERING, INC. war rants this unit to be free of defects in materials and workmanship for a period of from date of purc hase. OME GA ’ s WARRAN TY adds an additional one (1) month grace period to the normal to cover handling and shipping time. This ensures that OME GA ’ s customer s receive maximum coverage on eac h product. If the un[...]
-
Page 44
Where Do I Find Everything I Need for Pr ocess Measurement and Contr ol? OM EGA…Of Course! Shop online at omega.com TEMPERA TURE 䡺 ⻬ Thermocouple, R TD & Thermistor Pr obes, Connectors, Panels & Assemblies 䡺 ⻬ W ire: Thermocouple, RTD & Thermistor 䡺 ⻬ Calibrators & Ice Point References 䡺 ⻬ Recorders, Contr ollers &[...]