English dropdown-ico

ParaBody 883 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of ParaBody 883, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of ParaBody 883 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of ParaBody 883. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of ParaBody 883 should contain:
- informations concerning technical data of ParaBody 883
- name of the manufacturer and a year of construction of the ParaBody 883 item
- rules of operation, control and maintenance of the ParaBody 883 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of ParaBody 883 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of ParaBody 883, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the ParaBody service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of ParaBody 883.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the ParaBody 883 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    1 883 SECOND ST ACK OPTION FOR 880 GYM SYSTEM CLASS H PAR T # 7168901 REV . C Revision: 3/08/02 USER’S GUIDE W ARNING: Read and follow all directions for each step to insure proper assembly of this product. V ersion: 883102[...]

  • Page 2

    THERE IS A RISK ASSU MED BY IND IVIDUALS W HO USE T HI S TYPE OF EQUIPMENT. TO MINIMIZE RISK F OLLOW THESE RULE S ! 1. Before u sing, read al l the w arnings and in structions on the use of this mach ine. Use only for in tended exercise. DO NOT mo dify the m achine. 2. Obtain a medica l exam bef ore begi nning any exercise pro gram. 3. Keep body a [...]

  • Page 3

    IMPOR T ANT NOTES Please note: T ools Required for Assembly * Thank you for purchasing the ParaBody 880 Second Stack Option. Please read these instructions thoroughly and keep them for future reference. 3 NOTE: BOL T LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOL T . BOL T LENGTH RULER: * This product must be assembled on a flat, leve[...]

  • Page 4

    PA R T # 7160208 7167908 6523401 7095701 7012102 6957302 7165701 7156101 31 16201 6972201 3108002 6978101 KEY 1 2 3 4 5 6 7 8 9 10 11 12 QTY 1 1 2 1 2 1 1 1 2 1 2 1 PA R T # 3102924 3102807 3102906 3102955 3102802 3102501 3102503 6939202 6382301 3221702 3103302 7159801 DESCRIPTION 3/8 X 1-3/4” BOL T 3/8” LOW HEIGHT LOCK NUT 3/8 X 4” BOL T 3/8[...]

  • Page 5

    STEP 1: 5 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • REMOVE the PRESS/LEG CABLE from the 880 GYM SYSTEM . Discard the PRESS/LEG CABLE . See FIGURE 1. (NOTE: Remove pulleys for ease of removal.) • NOTE: Follow these steps if assembling the SECOND ST ACK OPTION to a completely assembled (including cables) 880 GYM SYSTEM without LEG PRESS OPTION, othe[...]

  • Page 6

    STEP 2: FIGURE 2 6 • Remove the two 3/8 X 4” BOL TS, four 3/8” W ASHERS and two 3/8” LOCK NUTS from the REAR UPRIGHT as shown in FIGURE 2. 3/8 X 4” BOL TS STEP 3: FIGURE 3 • SECUREL Y assemble the ST ACK BASE (1) to the BASE FRAME using two 3/8 X 4-1/4” BOL TS (16), two previously removed 3/8 X 4” BOL TS, four 3/8” W ASHERS (18), [...]

  • Page 7

    7 FIGURE 5 STEP 5: FIGURE 4 • Insert two WEIGHT PLA TE BUSHINGS (21) into each of the fifteen WEIGHT PLA TES (20) as shown in FIGURE 4. STEP 4: • Slide the WEIGHT PLA TE SHAFT (4) thru the hole in the HEAD PLA TE (6), and lock in place using one E-RING (22) as shown in FIGURE 5. 21 20 6 22 4 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2[...]

  • Page 8

    FIGURE 6 STEP 6: 8 • Insert two GUIDE RODS (3) into the ST ACK BASE (1) as shown on FIGURE 6. (NOTE: If the 880 SHROUD OPTION was purchased, place the GUIDE RODS (3) through the BOTTOM SHROUD BRACKET (found in SHROUD OPTION box) and into the ST ACK BASE (1) as shown in FIGURE 6. • Slide two WEIGHT ST ACK SP ACERS (5), two 3/4” FLA T W ASHERS [...]

  • Page 9

    FIGURE 7 STEP 7: 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • CAREFULL Y remove the BOOM PLA TE from the the REAR UPRIGHT and the FRAME as shown in FIGURE 7. Discard the BOOM PLA TE. FIGURE 8 STEP 8: • Swing the GUIDE RODS (3) into the guide rod bushings in the LEFT BOOM BRACKET (2) as shown in FIGURE 8. • SECUREL Y assemble the LEFT BOOM BRACKET ([...]

  • Page 10

    10 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 9: FIGURE 9 • Unscrew the threaded ends of the WEIGHT ST ACK CABLE from the WEIGHT ST ACK SHAFT and remove the two PULLEYS from the BOOM BRACKET . See FIGURE 9. WEIGHT ST ACK CABLE PULLEY BOOM BRACKET[...]

  • Page 11

    11 STEP 10: FIGURE 10 • Assemble two 3-1/2” PULLEYS (9) to the LEFT BOOM BRACKET (2) using two 3/8 X 1-3/4” BOL TS (13) and two 3/8” LOW HEIGHT LOCK NUTS (14) as shown in FIGURE 10. • Screw the long threaded end of the WEIGHT ST ACK CABLE into the end of the HEAD PLA TE (6) .See FIGURE 10. • Route the WEIGHT ST ACK CABLE around the pull[...]

  • Page 12

    12 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 10: FIGURE 1 1 • Route the new PRESS ST ACK CABLE (7) thru the PRESS ST A TION as shown. (NOTE: Remove pulleys for ease of installa- tion.) 7[...]

  • Page 13

    13 STEP 12: FIGURE 12 • Route the new PRESS ST ACK CABLE (7) thru the PEC ST A TION as shown. (NOTE: Remove pulleys for ease of installation.) Slide GUIDE RODS up just enough to get the cable end thru. Push GUIDE RODS down when finished. STEP 13: FIGURE 13 • Screw the threaded end of the PRESS ST ACK CABLE (7) into the end of the HEAD PLA TE. S[...]

  • Page 14

    STEP 14: FIGURE 14 14 • Route the LEG CABLE (8) around the 3-1/2” PULLEY on the PULLEY PLA TES using one existing 3/8 X 1-3/4” BOL T and one existing 3/8” LOCK NUT . See FIGURE 14. • Securely assemble the threaded end of the LEG CABLE (8) to the THREADED HOUSING (24) then assemble the THREADED HOUSING (24) to the bracket on the ST ACK BAS[...]

  • Page 15

    15 TIGHTEN! 20 6 23 3 STEP 15: FIGURE 15 • SECUREL Y tighten all loose frame connections. • Slide the SHAFT COLLARS (23) to the top of the GUIDE RODS (3) and tighten set screws as shown in FIGURE 15. • Adjustments can be made in the above locations to set the correct amount of tension in the cables. (NOTE: FLOA TING PULLEYS should rest agains[...]

  • Page 16

    16 FIGURE 1 STEP 1: PRESS/LEG CABLE • NOTE: Follow these steps if assembling the SECOND ST ACK OPTION to a completely assembled (including cables) 880 GYM SYSTEM with LEG PRESS OPTION (already assembled to the 880), otherwise please refer to P AGE 5. • REMOVE the PRESS/LEG CABLE as shown in FIGURE 1. Discard the PRESS/LEG CABLE. (NOTE: Remove p[...]

  • Page 17

    SHOR T LEG PRESS CABLE FIGURE 2 STEP 2: • Carefully remove and discard the SHOR T LEG PRESS CABLE from the LEG PRESS as shown in FIGURE 2. 17 STEP 3: FIGURE 3 • Remove the two 3/8 X 4-1/4” BOL TS, two 3/8 X 3-3/4” BOL TS, eight 3/8” W ASHERS, PULLEY BRACKET and four 3/8” LOCK NUTS from the REAR UPRIGHT and the BASE FRAME as shown in FIG[...]

  • Page 18

    18 STEP 4: FIGURE 4 • SECUREL Y assemble the ST ACK BASE (1) to the BASE FRAME using two 3/8 X 4” BOL TS (15), two previously removed 3/8 X 4-1/4” BOL TS, eight previously removed 3/8” W ASHERS and four previously removed 3/8” LOCK NUTS as shown in FIGURE 4. 3/8 X 4” 15 3/8 X 4-1/4” BOL TS BASE FRAME 1 STEP 5: FIGURE 5 • Remove the [...]

  • Page 19

    STEP 6: FIGURE 6 SHOR T LEG PRESS CABLE • Remove the rest of the SHOR T LEG PRESS CABLE from the FRAME as shown in FIGURE 6. (NOTE: Remove pulleys for ease of installation.) 19 FRAME BOOM BRACKET[...]

  • Page 20

    STEP 8: FIGURE 8 • SECUREL Y assemble the PEC ST A TION P AD to the FRAME using two previously removed 3/8 X 3” BOL TS and two 3/8” W ASHERS (18). See FIGURE 8. 3/8 X 3” STEP 7: FIGURE 7 • Remove the PULLEY BRACKET , the PEC ST A TION P AD and two 3/8 X 3” BOL TS from the FRAME. Discard the PULLEY BRACKET . See FIGURE 7. PEC ST A TION P[...]

  • Page 21

    21 FIGURE 10 STEP 10: FIGURE 9 • Insert two WEIGHT PLA TE BUSHINGS (21) into each of the fifteen WEIGHT PLA TES (20) as shown in FIGURE 9. STEP 9: • Slide the WEIGHT PLA TE SHAFT (4) thru the hole in the HEAD PLA TE (6), and lock in place using one E-RING (22) as shown in FIGURE 10. 21 20 6 22 4[...]

  • Page 22

    FIGURE 1 1 STEP 1 1: 22 • Insert two GUIDE RODS (3) into the ST ACK BASE (1) as shown on FIGURE 1 1. (NOTE: If the 880 SHROUD OPTION was purchased, place the GUIDE RODS (3) through the BOTTOM SHROUD BRACKET (found in SHROUD OPTION box) and into the ST ACK BASE (1) as shown in FIGURE 1 1. • Slide two WEIGHT ST ACK SP ACERS (5), two 3/4” FLA T [...]

  • Page 23

    FIGURE 12 STEP 12: 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • CAREFULL Y remove the BOOM PLA TE (10) from the the REAR UPRIGHT and the FRAME as shown in FIGURE 12. Discard the BOOM PLA TE. FIGURE 13 STEP 13: • Swing the GUIDE RODS (3) into the guide rod bushings in the LEFT BOOM BRACKET (2) as shown in FIGURE 13. • SECUREL Y assemble the LEFT BOO[...]

  • Page 24

    24 STEP 14: FIGURE 14 • Unscrew the threaded ends of the WEIGHT ST ACK CABLE from the WEIGHT ST ACK SHAFT and remove the two PULLEYS from the BOOM BRACKET . See FIGURE 14. WEIGHT ST ACK CABLE PULLEY BOOM BRACKET[...]

  • Page 25

    25 STEP 15: FIGURE 15 • Assemble two 3-1/2” PULLEYS (9) to the LEFT BOOM BRACKET (2) using two 3/8 X 1-3/4” BOL TS (13) and two 3/8” LOW HEIGHT LOCK NUTS (14) as shown in FIGURE 15. • Screw the long threaded end of the WEIGHT ST ACK CABLE into the end of the HEAD PLA TE (6) .See FIGURE 15. • Route the WEIGHT ST ACK CABLE around the pull[...]

  • Page 26

    STEP 16: FIGURE 16 PULLEY PLA TES • Route the previously removed original LA T CABLE through the FRAME (1) and assemble one 3-1/2” PULLEY to the PULLEY PLA TES using one existing 3/8 X 1-3/4” BOL T and one exsisting 3/8” LOCK NUT . See FIGURE 16. 26 PULLEY LA T CABLE STEP 17: FIGURE 17 • Securely assemble the LA T CABLE to the THREADED HO[...]

  • Page 27

    27 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 18: FIGURE 18 • Route the new PRESS ST ACK CABLE (7) thru the PRESS ST A TION as shown. (NOTE: Remove pulleys for ease of installa- tion.) 7[...]

  • Page 28

    28 STEP 19: FIGURE 19 • Route the new PRESS ST ACK CABLE (7) thru the REAR UPRIGHT as shown. (NOTE: Remove pulleys for ease of installa- tion.) Slide GUIDE RODS up just enough to get the cable end thru. Push GUIDE RODS down when finished. STEP 20: FIGURE 20 • Screw the threaded end of the PRESS ST ACK CABLE (7) into the end of the HEAD PLA TE. [...]

  • Page 29

    STEP 21: FIGURE 21 29 • Route the LONG LEG PRESS CABLE around the 3-1/2” PULLEY on the PULLEY PLA TES using one existing 3/8 X 1-3/4” BOL T and one existing 3/8” LOCK NUT . See FIGURE 21. 0 1 2 34 5 6 1/2 1/2 1/2 1/2 1/2 1/2 BASE FRAME PULLEY PLA TES • Assemble the LONG LEG PRESS CABLE (from the 883 LEG PRESS OPTION box) to the PEDEST AL [...]

  • Page 30

    30 CABLE ROUTING DIAGRAM FIGURE 22 STEP 22: • Carefully route the LONG LEG PRESS CABLE thru the LEG PRESS as shown in FIGURE 22 and assemble the LONG LEG PRESS CABLE to the existing THREADED HOUSING . LONG LEG PRESS CABLE THREADED HOUSING[...]

  • Page 31

    31 TIGHTEN! 20 6 23 3 STEP 23: FIGURE 23 • SECUREL Y tighten all loose frame connections. • Slide the SHAFT COLLARS (23) to the top of the GUIDE RODS (3) and tighten set screws as shown in FIGURE 23. • Adjustments can be made in the above locations to set the correct amount of tension in the cables. (NOTE: FLOA TING PULLEYS should rest agains[...]