English dropdown-ico

Pelco 90 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Pelco 90, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Pelco 90 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Pelco 90. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Pelco 90 should contain:
- informations concerning technical data of Pelco 90
- name of the manufacturer and a year of construction of the Pelco 90 item
- rules of operation, control and maintenance of the Pelco 90 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Pelco 90 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Pelco 90, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Pelco service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Pelco 90.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Pelco 90 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    INST ALLA TION 090 Series Camclosure ® Indoor Integrated Camera System C2462M-D (3/08) Surface Mount/In-Ceiling[...]

  • Page 2

    [...]

  • Page 3

    C2462M-D (3/08) 3 Contents Important Safety Instructi ons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Descripti[...]

  • Page 4

    4 C2462M-D (3/08) List of Illustrations 1 How to Remove the Dome Bubble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2 Ceiling/W all In stallation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3 Concrete Ceiling/W a[...]

  • Page 5

    C2462M-D (3/08) 5 Important Safety Instructions 1. Installation and servicing should be d one only by qualified se rvice personnel and conform to all local codes. 2. Unless the unit is specifically marked as a NEMA T ype 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and must not be installed where exposed to rain and mois[...]

  • Page 6

    6 C2462M-D (3/08) Description The ICS090 Series Camclosure ® integrated camera system integrates a camera and lens package in a small, discreet dome. The system is easy to install and can be mounted or recessed to the surface of a ceiling or wall. Prior to the installation of your n ew system, thoroughly familiarize yourself with the information i[...]

  • Page 7

    C2462M-D (3/08) 7 Remove the Dome Bubble T urn the dome bubble counterclockwise and lift (refer to Figure 1). Place the b ubble on a nonabrasive surface. If the unit is supplied with a dome liner , remove the li ner b efore installing the un it. T o re move the liner , gently lift it from the unit. Place t he liner to the side; it will be rein stal[...]

  • Page 8

    8 C2462M-D (3/08) Install the Back Box The installation methods for the ICS090 Series include the following options: • Mount to the surface of a ceiling or wall • Install in a suspended ceiling • Install in a fixed ceiling or wall • Mount to the surface of a 4S standard electrical bo x • Install in a 4S deep electrica l box Select the bes[...]

  • Page 9

    C2462M-D (3/08) 9 4. Use the 6-32 toggle bolts (not supplied) to at tach the surfa ce mount ring and back box to the mounting surface, refer to Figure 2. NOTE: For a concrete ceiling/wall installation, use 8-32 mounting hardware (not suppl ie d), refer to Figure 3. Figure 2. Ceiling/Wall Installati on Figure 3. Concrete Ceiling/W all Installation[...]

  • Page 10

    10 C2462M-D (3/08) IN-CEILING INSTALLATION: SUSPENDED CEILING Refer to Figure 4 and complete the following steps. 1. Remove the ceiling tile from the ceiling. 2. Cut a 4-inch diameter h ole in the ceiling tile. 3. Remove the surface mount ring from the back box. Refer to Figure 5 and complete the following steps: a. Place your fingers on the circul[...]

  • Page 11

    C2462M-D (3/08) 11 Figure 5. How to Remove Surfac e Mount Ring from Back Box AC operation only: If you are wiring more than one ICS090 Camclosure to the same transformer , connect one side of the transformer to the red wire on all units, and then connect the other side of the transformer to the black wire on all units. Failure to connect all of the[...]

  • Page 12

    12 C2462M-D (3/08) IN-CEILING INSTALLATION: FIXED CEILING/W ALL Refer to Figure 6 and complete the following steps. 1. Cut a 4-inch diameter h ole in the ceiling/wall. 2. Remove the surface mount ring from the back box. Refer to Figure 5 and complete the following steps: a. Place your fingers on the circular marks loca ted on the sides of the surfa[...]

  • Page 13

    C2462M-D (3/08) 13 INSTALLATION TO THE SURF ACE OF A 4S STANDARD ELECTRICAL BOX Refer to Figure 7 and complete the following steps. 1. Attach the adapter ring to the 4S box with the two 8-32 x 1.00-inch screws (s upplied). 2. Connect the video cable/wires. BNC: Connect the BNC connector from the Camclosure to a mating BNC connector . T wisted pair:[...]

  • Page 14

    14 C2462M-D (3/08) INSTALLATION IN A 4S DEEP ELECTRICAL BOX Refer to Figure 8 and complete the following steps. 1. Remove the surface mount ring from the back box. Refer to Figure 5 and complete the following steps: a. Place your fingers on the circular marks loca ted on the sides of the surface mount ring. b. Pinch the sides. c. Lift and remove th[...]

  • Page 15

    C2462M-D (3/08) 15 Camera Positioning Manually rotate and tilt th e camera module to positio n the camera. Do not over- rotate the module. Figure 9. Positioning the Camera WAR NI NG : Excessively turning the module in one direct ion could result in damage to the wiring.    ì T ilt 140° î Pan 360° ï Rotation 360°[...]

  • Page 16

    16 C2462M-D (3/08) Camera Adjustments SWITCH SETTINGS SWITCH SETTINGS FOR FIXED FOCAL LENGTH LENS WITHOUT AUTO IRIS Refer to the switch drawing. The switch is located n ext to the lens. Automatic backlight compensation (factory setting) is used under vary ing lighting conditions (suc h as ou tdoors) or fixed lighting conditions where there are no b[...]

  • Page 17

    C2462M-D (3/08) 17 V ERTICAL PHASE ADJUSTMENT (24 V AC OPERATION ONLY) When using more than one camera power supply, a brief vertical roll may occur on the monitor when a camera view is switched. T o elim inate vertical roll, reverse the 24 V AC connections on one camera. If both cameras are connected to the same transformer , this should solve the[...]

  • Page 18

    18 C2462M-D (3/08) Reinstall the Dome Bubble DOME LINER INSTALLATION If the unit is supplied with a dome liner , reinsta ll t he liner before installing the dome bubb le. T o install the liner , refer to Figure 11 comp lete the following steps: 1. Align the studs located on the camera module with the clips on the liner . 2. Lightly pinch the sides [...]

  • Page 19

    C2462M-D (3/08) 19 DOME BUBBLE INSTALLATION T o insta ll the dome bubble refer t o Figure 12 and complete the fo llowing steps: 1. Select the bubble (clear or smoked). 2. Align the standoffs of the bubble with the slots of the back box. 3. T urn the bubble clockwise, until it locks in place. Figure 12. Installing the Dome Bubble[...]

  • Page 20

    20 C2462M-D (3/08) Service Connector An optional 4-foot service/monitor cable, part numb er ICS090-SC, is available for on- site setup and adjustments. T o use the cable simply plug one end of the cable directly into the service connector of the ICS090, and then connect the other end to any st andard BNC (VIDEO IN) connector on a monitor . T o asse[...]

  • Page 21

    C2462M-D (3/08) 21 Specifications BACKBOX Electrical Input V oltage 12 VDC or 24 V AC (±10%), autosensing Power Consumption 3 W or less Video Connector BNC General Pan/T ilt Adjustment Pan 360° T ilt 140° (20° to 160° range) Rotation 360° Construction Back Box and Surface Mount Ring ABS plastic Bubble Polycarbonate Finish White Environment In[...]

  • Page 22

    22 C2462M-D (3/08) The materials used in the manufacture of this document an d its components are compliant to th e requirements of Directiv e 2002/95/EC. This equipment co ntains electr ical or electron ic components that must be recycle d properly to comply with Direct ive 2002/96/EC of the European Union re garding the disp osal of waste electri[...]

  • Page 23

    PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, witho ut charge, any mer c handise proved defective in ma terial or wo rkmanship for a period of one year after th e date of shipment. Exception s to this warrant y are as noted below: • Five years on fiber opt ic products and TW3 000 Series unshield ed twisted pair (U[...]

  • Page 24

    Worl dwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .pelco.com ISO 9001 Australia | Finland | France | Germany | Italy | Macau | The Nethe rland s | Russia | Singapore South Africa | Spain | Sweden | United Arab Emirates[...]