English dropdown-ico

Pentair PS4 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Pentair PS4, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Pentair PS4 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Pentair PS4. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Pentair PS4 should contain:
- informations concerning technical data of Pentair PS4
- name of the manufacturer and a year of construction of the Pentair PS4 item
- rules of operation, control and maintenance of the Pentair PS4 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Pentair PS4 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Pentair PS4, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Pentair service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Pentair PS4.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Pentair PS4 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    Installation Data Installation Man u al PDA - Pool Digital Assistant W ARNING FOR YOUR SAFETY - This product must be installed and serviced by a pro fes sion al pool/spa service technician. The procedures in this manual must be followed ex act ly . Failure to follow warning notices and instructions may result in property damage, serious injury , or[...]

  • Page 2

    [...]

  • Page 3

    Page 3 T able of Contents Section 1. Important Safety Instructions .............. 4 Section 2. System Overview ................................... 6 2.1 Package Contents .................................... 6 2.2 System Component Speci fi cations and Dimensions ....................................... 7 2.3 Basic Plumbing ..........................[...]

  • Page 4

    Page 4 Section 1. Important Safety Instructions READ AND FOLLOW ALL INSTRUCTIONS LIRE LA NOTICE TECHNIQUE. All electrical work must be performed by a licensed electrician and conform to all national, state, and local codes. When installing and using this electrical equipment, basic safety precautions should always be followed, including the followi[...]

  • Page 5

    Page 5 CAUTION A ground-fault circuit-interrupter must be provided if this device is used to control underwater lighting fixtures. The conductors on the load side of the ground-fault circuit-interrupter shall not occupy conduit, boxes, or enclosures containing other conductors unless the additional conductors are also protected by a ground-fault ci[...]

  • Page 6

    Page 6 Section 2. System Overview 2.1 Package Contents All Jandy AquaLink RS Systems come complete with the appropriate number of 3HP relays needed. Pool Digital Assistant (PDA) System Sub-Assembly Power Centers (Sold Separately) Standard Power Center (with mounting brackets) Sub-Panel Power Center (with mounting brackets and circuit breaker mounti[...]

  • Page 7

    Page 7 2.2 System Component Speci fi cations and Dimensions T able 1 Specifications (USA and Canada) Power Supply 120 V AC; 60 Hz; 3 A Contact Rating (Relays) High voltage - 25 A; 3HP @ 240 V AC 1½ HP @120 V AC 1500 W atts Incandescent Low V oltage - Class T wo, 1 A @ 24 V AC Service Switch All Circuits (located at Power Center in Service Mode) D[...]

  • Page 8

    Page 8 2.3 Basic Plumbing 2.3.1 Plumbing for Pool and Spa Combination The following plumbing diagrams illustrate simplified versions of standard plumbing setups for a pool and spa that share the same filter pump, filter , and heater . The intake and return Jandy V alve Actuators (JV As) turn si mul ta neous ly so when the Spa mode is selected on th[...]

  • Page 9

    Page 9 2.3.2 Booster Pump Pool Cleaner Plumbing Heater Filter Filter Pump Pool Intake Spa Intake Spa Return Pool Return Check V alve Spa Make-up Booster Pump 2.3.3 Non-Booster Pump Pool Cleaner Plumbing Filter Filter Pump Pool Intake Spa Intake Spa Return Pool Return Check V alve Spa Make-up Energy Filter Cleaner Line Heater[...]

  • Page 10

    Page 10 3.1 Power Center Mounting 1. The Power Center should be located at or near the equipment pad. Locate the Power Center at least fi ve (5) feet or more away from pool/spa and fi ve (5) feet off the ground. All na tion al, state, and local codes are applicable. NOTE For Canadian installations, the Power Center must be at least three (3) mete[...]

  • Page 11

    Page 1 1 3.2.3 Bonding the Power Center Install a bonding lug to the Power Center enclosure. Connect the bond lug, using a #8 solid copper core wire, to an approved earth ground (an approved ground stake, grid, or conducting metal water pipe buried to a sufficient depth). See Figure 3. 3.2.2 3HP (Standard) Relays For each piece of 240 volt equipmen[...]

  • Page 12

    Page 12 3.2.4 Underwater Lighting GFCI Wiring Figure 4. GFCI Installation for Underwater Lighting GFCI Outlet OPTIONAL Standard Power Center GFCI Outlet (Optional) OPTIONAL Sub-Panel Power Center 3.2.5 Jandy Pool and Spa Lights W iring The Jandy Pool and Spa Lights can be wired into the Jandy AquaLink RS control system to ensure simplified operatio[...]

  • Page 13

    Page 13 GFCI Black White Green 120V Jandy Light Ground Ground Neutral 120 V AC Power Supply Junction Box Figure 5. 120-V olt Jandy Pool and Spa Light Wiring Diagram Figure 6. 12-V olt Jandy Pool and Spa Light Wiring Diagram GFCI Ground Ground Neutral Black White Green 12V Jandy Light Black White Green 120V/12V Transformer 120 V AC Power Supply Junc[...]

  • Page 14

    Page 14 Figure 8. PDA J-Box Cable Connection to Power Center PCB Conduit Knockout for Low V oltage PDA J-box Wire Heyco Fittings for Low V oltage JV A and Sensor Wires Low V oltage Raceway High V oltage Knock outs for Conduit (DO NOT run any Low V oltage wires through these knockouts) 3.3 Low V oltage Wiring 3.3.1 Bezel Connection Plug the 24 V AC [...]

  • Page 15

    Page 15 3.4 Heater Connection The heater connection section applies to all heaters or heat pumps with thermostatic circuitry of 24 V AC or less (see pages 15 thru 17 for brand specific installation). NOTE If you are connecting a heater with thermostatic circuitry of 120 V AC or greater , do not connect to the green, 10-pin T erminal Bar . Instead, [...]

  • Page 16

    Page 16 3.4.4 Guidelines for a Gas Heater and a Jandy AE Series Heat Pump/Chiller Installation NOTE The following steps provide the procedure for installing a Jandy AE Series Heat Pump. 1. Install a fi xed resistor , with a value of 2.2K Ohms, in the solar sensor terminals #3 and #4 of the green, 10-pin terminal bar of the AquaLink RS Power Center[...]

  • Page 17

    Page 17 3.5 T emperature Sensors 1. Drill 3/8" hole in pipe between fi lter pump and fi lter and install the W ater T emperature Sensor per instructions (make certain the o-ring is in place). 2. Install Air T emperature Sensor outside the Power Center can, not in direct sunlight and away from motors and other heat sources. 3. Install Solar T[...]

  • Page 18

    Page 18 3.7.2 PDA Handheld Remote Installation 1. Remove the Handheld Remote from the packaging. 2. On the back of the Handheld Remote, loosen and remove the two (2) screws that secure the cover for the battery chamber (see Figure 19). 3. Install two (2) AA batteries. Ensure that the polarity is correct. 4. Re-install the cover for the battery cham[...]

  • Page 19

    Page 19 Section 4. System Startup 4.1 Handheld Remote Programming 4.1.1. Basic Programming Menu T o set a particular piece of equipment to turn on and off at predetermined times, highlight MENU and press SELECT (see Figure 23). Highlight PROGRAM and press SELECT . Use the UP or DOWN buttons to highlight the equipment (for example, Filter Pump) then[...]

  • Page 20

    Page 20 4.1.2 Set the T ime Menu T o set the time, highlight the MENU and press SELECT . Highlight SET TIME and press SELECT (see Figure 24). Use the UP or DOWN button to set the values. Press SELECT to continue. Pool/Spa Only - Highlight MENU and press SELECT . Highlight SET TEMP and press SELECT (see Figure 26). The message TEMP1 must be higher t[...]

  • Page 21

    Page 21 4.1.5 Set Freeze Pr otection Menu Highlight MENU and press SELECT . Highlight SYSTEM SETUP and press SELECT (see Figure 28). Highlight FREEZE PROTECT and press SELECT . Use the UP or DOWN button to change the temperature. Once the temperature is set press the SELECT button to move to the next screen to assign freeze protection to a selected[...]

  • Page 22

    Page 22 4.2 Restarting the System (Clear Memory) Menu T o remove all labeling, programming, assignments and temperature settings, highlight MENU and press SELECT . Highlight SYSTEM SETUP and press SELECT (see Figure 30). Highlight CLEAR MEMOR Y and press SELECT . Highlight CONTINUE and press SELECT . Use the UP or DOWN button to highlight YES or NO[...]

  • Page 23

    Page 23 Battery Backup A nine-volt battery is located at the power center . The battery keeps the clock running during a power outage so the time and date will be correct when power is restored. Programming will not be lost even if the battery is dead. Do not install the battery in the power center until the system is ready to operate. Battery will[...]

  • Page 24

    Page 24 4.4 PDA Handheld Remote Menu Flow Chart MENU PROGRAM SET TEMP POOL HEA T SP A HEA T SET TIME SET MONTH, DA Y , YEAR & TIME PDA OPTIONS SET AUT O-OFF BACKLIGHT ASSIGN HOTKEYS SYSTEM SETUP LABEL AUX TEMP CALIBRA TE SOLAR HEA T PRIORITY † ASSIGN JV As SP A SWITCH SERVICE INFO CLEAR MEMORY GENERAL LABELS LIGHT LABELS WTRF ALL LABELS (TYPE[...]

  • Page 25

    Page 25 Section 5. T roubleshooting 5.1 PDA Quick T roubleshooting Guide The AquaLink RS PDA will stop communicating anytime interference (such as a 900 MHz device) prevents a valid signal transmission. When communication is lost the PDA Handheld Remote will lock on the startup screen until a good link is again achieved, usually within a few sec on[...]

  • Page 26

    Page 26 Symptom Problem Possible Solution One button on the Four Function Remote does not operate. Check programming first. If the Four Function Remote is programmed correctly , the button may be shorted. NOTE If dip switch 1 (CLEANER) is on, button # 3 on the Four Function Remote will not operate when in spa mode unless this button is programmed t[...]

  • Page 27

    Page 27 Section 6. Power Center Wiring Diagram Aux. 4 Relay Aux. 7 Relay Aux. 5 R elay Aux. 6 Relay Filter Pump R e lay Aux. 3 R elay Aux. 1 Relay Li ne One Low V o l tage R a ceway ( do no t r un h igh volt age wi r e in thi s c ompar tment) Line Tw o Load One Load T wo Aux. 2 Relay Groun ding Ba r Wire Nut t o 120V AC Power System Power Intake JV[...]

  • Page 28

    Page 28 Section 7. Power Center PCB DIP Switch Settings IMPORT ANT Do not program equipment ON/OFF times until all DIP switches are set. 7.1 DIP Switch Functions DIP #1 ON- AUX 1 Controls Pool Cleaner If you installed a booster pump for a pool cleaner , the relay coil for the booster pump must be plugged into the AUX 1 relay socket. If a non-booste[...]

  • Page 29

    Page 29 7.2 DIP Switch Settings for Pool and Spa Combination DIP Switch # OFF ON 1 AUX1= any equipment AUX1= Pool Cleaner 2 AUX2= any equipment AUX2= Low Speed for a two-speed filter pump. Filter pump circuit becomes High Speed. 3 AUX3= any equipment AUX3= Spa Spillover effect- Combination controls only . 4 Heater cool down operates. Heater cool do[...]

  • Page 30

    Page 30 7.3 DIP Switch Settings for Pool or Spa Only DIP Switch # OFF ON 1 AUX1= any equipment AUX1= Pool Cleaner 2 AUX2= any equipment AUX2= Low Speed for a two-speed filter pump. Filter pump circuit becomes High Speed. 3 AUX3= any equipment No change 4 Heater cool down operates. Heater cool down disabled. 5 Normal operation Factory adjustment- wh[...]

  • Page 31

    Page 31 Section 8. General, W ater Featur e and Light Aux Labels General Labels Light Labels W aterfall Labels Aerator Air Blower Backwash Booster Pump Chem Feed Cleaner Color Wheel Drain Line Fan Fiber Optic Fill Line Filter Pump Floor System Fogger Fountain Heat Pump Heater Hi-E2 High Speed Home A/C Home Heat Jet Pump Lite Lamp Low Speed Mist Mus[...]

  • Page 32

    LIMITED W ARRANTY Thank you for purchasing Jandy ® pool and spa products. Jandy Pool Products, Inc. warrants all parts to be free from manufacturing defects in materials and workmanship for a period of one year from the date of retail purchase, with the following exceptions: • AquaLink ® RS units installed with Jandy ® Surge Protection Kits wi[...]