Planet ADSL 2/2+ Router ADE-3410 manual

ADSL 2/2+ Router with USB Port ADE-3410 User's Manual 1[...]

Copyright Copyright © 2008 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, tr ansmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the p[...]

This device complies with Part 15 of the FCC Ru les. Operation is subj ect to the Following two conditions: (1) This device may not cause ha rmful interference, and (2) this Device must accept any interference received, including interference that may cause undesire d operation. Federal Communication Commission (FCC) Radiation Exposure Statement Th[...]

Table of Contents 1. Intr oducti on ................................................................................................................ ...... 6 1.1 Feat ure .................................................................................................................... 6 1.2 Package Contents........................................[...]

5 3.5.3.2 DMZ ..................................................................................................... 38 3.5.4 Rout ing ......................................................................................................... 38 3.5.4.1 RIP ...............................................................................................[...]

1. Introduction The PLANET ADSL 2/2+ Router, ADE-3410, prov ides office and residential users the ideal solution for sharing a high-speed ADSL 2/2+ broadband Internet connection on one Ethernet port and one USB port. It can support downstream transmission rates of up to 24Mbps and upstream transmission rates of up to 3.5Mbps. The product supports P[...]

 Dynamic DNS Support DDNS, when used with the Virtua l Servers feature, allows users to connect to Servers on your LAN using a Domain Name, even if you have a dynamic IP address which changes every time you connect.  VPN Pass through Support PCs with VPN (Virtual Private Networking) software using PPTP, L2TP, and IPSec are transparently suppo[...]

Front Panel LED definition LED Meaning 1 PWR Lit when power is ON. 2 Link Lit when DSL line is connected. Blink when DSL line is training. 3 Data Blink when DSL data is transferring. 4 LAN Lit when connected to an Ethernet device. Blink when data is Transmitted / Received. 5 USB Lit when the USB port is connected to the PC and working properly. Rea[...]

2. Installation This chapter offers information about installing your router. If you ar e not familiar with the hardware or software par ameters presented here, please cons ult your service provider for the values needed. 2.1 System Requirement 1. Personal computer (PC) 2. Pentium III 266 MHz processor or higher 3. 128 MB RAM minimum 4. 20 MB of fr[...]

If do not need to connect to the splitter, z Connect the modem to wall jack with a RJ-11 cable. z Use Ethernet cable to connect “LAN” port of the modem and netwo rk adaptor of your computer. 2.3 Configuring the Network Properties Configuring PC in Windows XP 1. Go to St art / Control Panel (in Classic View) . In the Control Panel, double-click [...]

5. Select the Obt ain an IP address automatically and the Obt ain DNS server address automatically radio buttons. 6. Click OK to finish the configuration. Configuring PC in Windows 2000 1. Go to St art / Settings / Control Panel . In the Control Panel, double-click on Netw ork and Dial-up Connections . 2. Double-clic k Local Area Connection . 11[...]

3. In the Local Area Connection St atus window click Properties . 4. Select Internet Protocol (TCP/IP) and click Properties . 5. Select the Obta in an IP address automatic ally and the Obt ain DNS server address automatically radio buttons. 6. Click OK to finish the configuration. 12[...]

Configuring PC in Windows 98/Me 1. Go to St art / Settings / Control Panel . In the Control Panel, double-click on Network and choose the Configuration tab . 2. Select TCP/IP Æ NE2000 Comp atible , or the name of your Network Interface Card (NIC) in your PC. 3. Select the Obt ain an IP address automatically radio button. 4. Then select the DNS Con[...]

3. W eb Configuration Management Determine your connection settings Before you configure the router, you need to know the connection information supplied by your ADSL service provider. Connecting the ADSL Rou ter to your network Unlike a simple hub or switch, the setup of t he ADSL Router consists of more than simply plugging everything together. B[...]

Once you have powered on ADE-3410, system will boot up and connect to DSLAM automatically. In login dialog, enter “admin” as user name and “admin” as default password. After log in, you will s ee the following page. The default screen is Wizard setting screen. You can configure the device step by step. 3.1 ADSL Router Status The Status scre[...]

3.1.2 LAN Status You can see the LAN IP address, Mask, DHCP st atus, MAC and DHCP Client Table in this screen. 3.1.3 WAN Status You can see the VPI/VCI, Encapsulation ty pe, Protocol, WAN IP address, Gateway and DNS information in this screen. 16[...]

3.1.4 Port Mapping You can see the Port Mapping information in this screen. It includes the status and Mapping Relation. 3.1.5 Statistic You can see the Statistic information in this scr een. It includes the Tra ffic and DSL statistic. Traffic Statistic Screen The screen shows the statistic of LAN, WLAN and WAN Port. Click the Refresh button to ref[...]

DSL Statistic The screen shows the ADSL line statistic. 3.1.6 ARP Table You can see the ARP information in this screen. Click the Refresh button to refresh the information. 18[...]

3.2 Wizard You can use "Wizard" to setup the router as follows, and the router will connect to the Internet via ADSL line. Step 1. Click "Wizard" to get into the quick setup pr ocedures. It will show the below screen. Enter the VPI / VCI value that provided by your ISP. Step 2. Click " Next " to select your WAN Connect[...]

Step 3. Click " Next " to setup to select the WAN IP type, and the WAN IP setting is provided by your ISP. Step 4. Enter the user name and password that your ISP has provided to you. Select the connection type that you want to use. There are three types for your selection – Continuous , Connect on Demand and Manual . 20[...]

Step 5. Click " Next " to setup your LAN IP and DHCP Server setting. Step 6. Enter the Finish to save settings and reboot the device or click Back to modify your settings. 21[...]

3.3 LAN The LAN setup includes two parts – LAN Interface and DHCP Settings. 3.3.1 LAN Interface Settings There are the IP settings of the LAN Interface for the device. These settings may be referred to as Private settings. You may change the LAN IP address if needed. The LAN IP address is provided to your internal netwo rk and cannot be seen on t[...]

3.3.2 DHCP Server Settings Enable the DHCP Server if you are using this device as a DHCP server. This page lists the IP address pools available to hosts on your LAN. The device distributes numbers in the pool to hosts on your network as they request Internet access. You can setup DHCP server to assign IP addre ss to your PC automatically. You can a[...]

IP Pool Range: Enter the start IP and end IP address y ou wish to use as the DHCP serve r's IP assignment. Show Client : It shows the current client which is connecting with your ADSL router. Max Lease Time: Enter the amount of time you wis h to lease out a given IP address. Domain Name: Enter your domain name. Gateway Address: Enter the defau[...]

3.4 WAN 3.4.1 WAN Interface ADSL 2/2+ Router provide 8 PVCs with different channel mode. You can select the Bridge / MER / PPPoE / PPPoA mode for your environment. Bridge Mode The device can be configured to act as a bri dging device between your LAN and your ISP. Bridges are devices that enable 2 or more networks to communicate as if they are 2 se[...]

function saves your changes from RAM to flash memory and then reboot the system. PPPoE / PPPoA Mode Select this option if your I SP requires you to use a PPPoE / PPPoA connection. This op tio n is typically used for DSL service. Please ent er the proper information in the fields. 1. Open the WEB page at “WAN Æ WAN Interface” . 2. Select the Ch[...]

MER Mode Select this option to set static IP information. You will need to ent er in the encapsulation type, IP address, subnet mask, and gateway address pr ovided to you by your ISP. Each IP address entered in the fields must be in the appropriate IP form, which is 4 IP octets separated by a dot (x.x.x.x). The Router will not accept the IP address[...]

3.4.2 ATM Settings The page is for ATM PVCs’ QoS mode setting. The device supports 4 QoS mode — UBR / CBR /rt-VBR / nrt-VBR. You can click the “ATM Setting” on the WAN Interface setting screen. ATM QoS: Select the Quality of Service types for this Virtual Circuit. The ATM QoS types include CBR(Constant Bit Rate ), VBR(Variable Bit Rate) and[...]

MBS: Maximum Burst Size (MBS) is the maximum number of cells that can be sent at the PCR. After MBS is reached, cell rates fall bel ow SCR until cell rate averages to the SCR again. At this time, more cells (up to the MBS) can be sent at the PCR again. “Apply Changes”: Set new PVC QoS mode and val ues for the selected PVC. “Undo”: Discard y[...]

3.5 Advance You can configure different advanced se rvices in this part. It includes DNS, Firewall, Virtual Server, Routing, IP QoS, Anti-DoS, Port Map ping and Other. 3.5.1 DNS In this screen, you can modi fy the DNS server settings. It includes the DNS and DDNS functions. DNS Configuration Attain DNS Automatically: If “Attain D NS Automatically[...]

Enable: Enable or disable DDNS. DDNS Provider: Choose the option of provider. It supports the DynDns and TZO. Hostname: Type the domain name assigne d to your ADSL by your Dynamic DNS provider. DynDns Settings: Username: Type your user name. Password: Type the password assigned to you. TZO Settings: E-mail Address : Type your e-mail address. Key: T[...]

3.5.2 Firewall Firewall is an advance feature us ed to deny or allow traffic from passing through the device. ADSL router support some firewall related functi ons. It includes the IP/P ort Filter, MAC Filter and URL Blocking. 3.5.2.1 IP/Port filtering Use the IP/Port filters to deny / allow parti cular LAN IP addresses from accessing the Internet. [...]

Rule Action: Select the Deny or Allow for your rules. Direction: Select the Outgoing or Incoming. Protocol: Set protocol type to be blocked or allowed. Src IP Address / Mask / Port: Set the subnet of source side computers to be denied / allowed access to the destination side computers. An individual source IP address can be designated for filtering[...]

3.5.2.2 MAC Filtering Use the MAC filters to deny computers within the local ar ea network from accessing the Internet. Entries in Filter Table are used to re strict certain types of data packets from your local network to Internet through the Gateway. Use of such filters can be helpful in securing or restricting your local network. Default Action:[...]

35 Src MAC Address: Set the MAC address of source si de computers to be denied/allowed access to the destination side computers. Dst MAC Address: Set the MAC address of desti nation side computers to be denied/allowed access to the source side computers. Click “Add” button to add this filtering rule. " Note Please Commit/Reboot if you want[...]

3.5.2.3 URL Block This page is used to configure the Block ed FQDN (Such as tw.yahoo.com) and filtered keyword. Here you can add / del ete FQDN and filter ed keyword. URL Blocking: Enable or Disable URL Blocking. Click t he “Apply Changes” to apply your setting. URL Blocking: Enter the FQDN in the field and click the “Add FQDN” button to ad[...]

3.5.3 Virtual Server The Virtual Server is the server or serve r(s) behind NAT (on the LAN), for example, Web server or FTP server, that you can make visible to the outside world even though NAT makes your whole inside network appear as a single machine to the outside world. The Virtual Server includes two parts – Services and DMZ . 3.5.3.1 Servi[...]

3.5.3.2 DMZ A DMZ (Demilitarized Zone) allows a single computer on y our LAN to expose ALL of its ports to the Internet. Enter t he IP address of that computer as a DMZ (Demilitarized Zone) host with unrestricted Internet access. When doing this, the DMZ host is no longer behind the firewall. Enable DMZ: Click it to enable the DMZ function. Enter ?[...]

To activate RIP for the device, select the “Enabled” radio button for RIP Mode and click “Apply Changes” to apply it. To configure an individual interface, select the Interface, Receive Mode and Send mode. Click the “Add” button to save the configuration, and to start or st op RIP based on the Global RIP mode selected. 3.5.4.2 Static Ro[...]

static route information. Destination: The IP address where packets will go to. Subnet Mask: The subnet mask of the destination IP address. Next Hop: The gateway that the packets will pass by during transmission. Metric: Metric represents the “cost” of transmission for routing purposes. IP Routing uses hop count as the measurement of cost, with[...]

41[...]

3.5.6 Anti-DoS "Denial-of-Service Attack" (DoS Attack), a type of attack on a network that is designed to bring the network to its knees by flooding it with useless traffic. This page is used to prevent DOS attacks that you configure. Select “Enable” can automatically detect and block Denial of Service (DoS) attacks, such as Ping of D[...]

3.5.7 Port Mapping Port Mapping supports multiple ports to PVC and bridging groups. Ea ch group will perform as an independent network. To support this feature, you must create mapping groups with appropriate LAN and WAN in terfaces using the “ ->” button. The “ <- “button will remove the grouping and add the ungrouped interfac es to [...]

3.5.8 Other This function includes as following parts – IGMP Proxy, UPnP and Bridge. 3.5.8.1 IGMP Proxy IGMP Proxy enables the system to issue IGMP host messages on behalf of hosts that the system discovered through standard IGMP interfaces. The system acts as a proxy for its hosts when you enable it by doing the follows:  Enable IGMP proxy on[...]

Click “Enable” to enable UPnP function and select the WAN Interface. Click “Apply Changes” to apply your setting. " Note Please Commit/Reboot if you want to make th is settings effective immediately 3.5.8.3 Bridge This page is used to configure the bridge parame ters. Here you can change the settings or view some information on the bri[...]

3.6 Admin You can configure admin management in this part. It includes Remote Access , Commit / Reboot , Password , Backup / Restore , Update Firmware , Time Zone , System Log , SNMP , TR-069 , and ACL . 3.6.1 Remote Access User can enable or disable remote m anagement services for the LAN and WAN. Select the service items which y ou want to remote[...]

3.6.3 Password This page is used to set the account to acce ss the web server of A DSL Router. The new password will be availability after system reboot. User Name: There are two level user accounts for your selection. The admin account has full rights for device management, and the user a ccount only can see the status information of this device. [...]

3.6.4 Backup / Restore This page allows you to backup current settings to a file or restores the settings from the file which was saved previously. Backup: Click the “Save…” button to backup the configuration of router. Restore: Click the “Browse...” button, select the correct update configure settings file. Then click the “Upload” to[...]

3.6.6 Time Zone The system time is the time used by the device for scheduling services. You can manually set the time or connect to a NT P (Network Time Protocol) server. If an NTP server is set, you will only need to se t the time zone. Current Time: It shows the current time. Time Zone: Choose the T ime Zone of your location . This will set the t[...]

3.6.7 System Log Click “System Log” to show the log information of dev ice. The system l og dialog allows you to view the system log and click the “Refresh” button to fresh the system event logs. System Log: You can Enable or Disable the System Log Function. Click “Apply Changes” to apply your setting. " Note Please Commit/Reboot i[...]

3.6.8 SNMP This page is used to configure the SNMP prot ocol. You can set SNMP related information here. Read Community: Select to set the password for in coming Get- and GetNext request from management station. Write Community : Select to set the password for incoming Set request from management station. The default password is “public” . When[...]

3.6.9 TR-069 This page is used to configure the TR-069 C PE. Here you may change the setting for the ACS's parameters. 3.6.10 ACL Access Control List Configuration If enabled, permits access to local management services from IP addr esses contained in the Access Control List. 52[...]

If enable ACL, and then only the effective IP in ACL can access the router. Step1 If you want to enable ACL, please choose "Enable" and then press " Appl y Changes " to apply your setting. Step2 Click the Enable checkbox. Step3 Enter the host IP address that you want to permit and click “ Add ”. Step4 Press "take effect[...]

Select your PVC and Flow Type that you want to test. Ente r the Loopback Location IP and then click “Go” for testing. 3.7.3 ADSL In this page, you can test the ADSL line tone status. Click “Go” to st art testing. The test result will come out about 3 minutes later and the page will refresh itself automatically. " Note This test is for [...]

3.7.4 Diagnostic The DSL Router is capable of testing your DS L connection. The individual tests are listed below. If a test displays a fail status, click "Run Diagnostic Test" button again to make sure the fail status is consistent. 55[...]

Appendix A: Glossary Address mask A bit mask select bits from an Internet addre ss for subnet addressing. The mask is 32 bits long and selects the network porti on of the Internet address and one or more bits of the local porti on. Sometimes it called subnet mask. AAL5 ATM Adaptation Layer - This layer maps higher layer user data into ATM cells, ma[...]

DHCP (Dynamic Host Configuration Protocol) DHCP is software that automatica lly assigns IP addresses to c lient stations logging onto a TCP/IP network. DHCP eliminates having to manually assign permanent IP addresses to every device on your network. DHCP software typically runs in servers and is also found in network devices such as Routers. DMT Di[...]

HTML Hypertext Markup Language - The page-coding language for the World Wide Web. HTML browser A browser used to traverse the Internet, such as Netscape or Microso ft Internet Explorer. http Hypertext Transfer Protocol - The protocol carry world-wide-web (www) traffic between a www browser computer and the www server being accessed. ICMP Internet C[...]

management protocol, such as SNMP and CMIP (Common Management Information Protocol). NAT Network Address Translation - A proposal for IP address reuse, where the local IP address is mapped to a globally unique address. NVT Network Virtual Terminal PAP Password Authentication Protocol PORT The abstraction used in Internet transport pr otocols to dis[...]

Router A system is responsible for making decisions about which of several paths network (or Internet) traffic will follow. To do this, it uses a routing protocol to gain information about the network and algorithms to choose the best r oute based on several criteria known as "routing metrics". Routing Table Information stored within a ro[...]

A static IP address is an IP addr ess permanently assigned to computer in a TCP/IP network. Static IP addresses are usually assigned to networked devices that are consistently accessed by multiple users, such as Server PCs, or printers. If you are using your Router to share your cable or DSL Internet connection, c ontact your ISP to see if they hav[...]

62 A link that seems and behaves like a dedicated poi nt-to-point line or a system that delivers packets in sequence, as happens on an actual point-t o-point network. In reality, the data is delivered across a network via the most appr opriate route. The sending and receiving devices do not have to be aware of the opt ions and the route is chosen o[...]

PLANET TECHNOLOGY CORPORA TION e-mail: sales@planet.com.tw http://www .planet.com.tw 1 1F , No. 96, Min Chuan Road, Hsin Tien, T aipei, T aiwan, R.O.C. T el:886-2-2219-9518 Fax:886-2-2219-9528 EC Declaration of Conformity For the following equipment: *T ype of Product : ADSL 2/2+ Router *Model Number : ADE-3410A / ADE-3410B * Produced by: Manufactu[...]