English dropdown-ico

Porter-Cable 33-413 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Porter-Cable 33-413, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Porter-Cable 33-413 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Porter-Cable 33-413. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Porter-Cable 33-413 should contain:
- informations concerning technical data of Porter-Cable 33-413
- name of the manufacturer and a year of construction of the Porter-Cable 33-413 item
- rules of operation, control and maintenance of the Porter-Cable 33-413 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Porter-Cable 33-413 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Porter-Cable 33-413, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Porter-Cable service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Porter-Cable 33-413.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Porter-Cable 33-413 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    INSTRUCTION MANUAL P ART NO. 424-03-651-0019 - 06-20-05 Copyright © 2004 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582). 14", 16", and 18" Long Arm Radial Saws (Model[...]

  • Page 2

    2 T ABLE OF CONTENTS Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to r educe the risk of personal injury . Improper operation, maintenance or modification of tools or equipment could r esult in serious injury and prop[...]

  • Page 3

    3 Indicates an imminently hazardous situation which, if not avoided, will r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, could r esult in death or serious injury . Indicates a potentially hazardous situation which, if not avoided, may r esult in minor or moderate injury . Used without the saf[...]

  • Page 4

    4 GENERAL SAFETY RULES READ AND UNDERST AND ALL W ARNINGS AND OPERA TING INSTRUCTIONS BEFORE USING THIS EQUIPMENT . Failure to follow all instructions listed below , may result in electric shock, fire, and/or serious personal injury or pr operty damage. IMPORT ANT SAFETY INSTRUCTIONS 1. FOR YOUR OWN SAFETY , READ THE INSTRUCTION MANUAL BEFORE OPERA[...]

  • Page 5

    5 F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS PERSONAL INJUR Y . ADDITIONAL SPECIFIC SAFETY RULES SA VE THESE INSTRUCTIONS. Refer to them often and use them to instruct others. 1 . DO NOT OPERA TE THIS MACHINE UNTIL it is assembled and installed according to the instructions. 2. OBT AIN ADVICE from your supervisor, instructor , or anothe[...]

  • Page 6

    Fig. 1 1. 3/8-16x1" Hex Head Screw (12) 2. 1/4-20x7/8" Round Head Screw (15) 3. 1/2-20x1/2" Hex Head Screw (4) 4. 3/8" Flat Washer (12) 5. 9/32" Flat Washer (15) 6. 3/8" Lockwasher (12) 7. 1/4" Lockwasher (4) 8. 3/8-16 Hex Nut (12) 9. 1/4-20 Hex Nut (1) 1. Blade Guard (1) 2. Angle Support (3) 3. Blade (1) 4. Cross[...]

  • Page 7

    7 UNP ACKING AND CLEANING Carefully unpack the machine and all loose items fr om the shipping container(s). Remove the protective coating fr om all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gasoline or lacquer thinner for this purpose). After cleaning, cover the unpainted surfaces[...]

  • Page 8

    8 ELEV A TING CRANK HANDLE Assemble elevating crank handle (A) Fig. 6 to rod in front of base using the r oll pin (B). TRACK-ARM LOCK Assemble track-arm lock handle (A) to the overarm (Fig. 7), and tighten set screw (B). Lock handle (A) should be tight when in the position shown in Fig. 7, and loose when pulled forward and r esting against stop (C)[...]

  • Page 9

    9 CUTTINGHEAD AND CROSS-CUT STOP TO TRACK-ARM 1. Remove two screws (A) and end cap (B) from track- arm, Fig. 8. 2. Hold cuttinghead assembly (D) Fig. 9, with both hands and insert the ball bearings (E) into the track- arm, as shown. Push cuttinghead all the way onto track-arm and tighten clamp knob (F). 3. Assemble cross-cut stop (C) to the track-a[...]

  • Page 10

    10 ST AR TER BOX TO BASE 1. Assemble bracket (A) to the bottom of the right side of saw base, (Fig. 12), using the 1/4-20x1/2" hex head screw (B), 1/4" lockwasher (D), and 1/4-20 nut (E). 2. Assemble the starter box (B) Fig. 13 to the right side of the base by inserting the three1/4-20x1/2" hex head screws (C) with 1/4" lock-was[...]

  • Page 11

    11 ADJUSTING T ABLE TOP P ARALLEL TO TRACK-ARM For accurate work the track-arm must be parallel to the table top at all points. T o check and adjust: 1. Move the motor and cuttinghead assembly (A) to the vertical position (Fig. 18). Position saw arbor (B) Fig. 18, so that it is approximately in the center of the front table boar d. Push track-arm c[...]

  • Page 12

    12 3. IMPORT ANT : T o prevent arbor nut fr om spinning when blade stops, place the 1-1/16" wrench (C) Fig. 23 on flats of arbor and firmly tighten arbor nut (A) with the 1-5/8" box end spanner wrench (D) (left handed thread). Firmly tighten set scr ew (E). 4. Remove screw (F) Fig. 25 that attaches inside leaf guar d (G) to rear of blade [...]

  • Page 13

    13 4. Attach eyelet (H) Fig. 30 of cable assembly (C) to "S" bracket (E). 5. NOTE: T o prevent pr emature wear of r etur n reel cable, position the return reel so that the cable does not rub against the wall of the return reel. Fig. 30 H C E Fig. 30B B OPERA TION ST AR TING AND STOPPING SAW 1. The on/off switch (A) Fig. 30A is located on [...]

  • Page 14

    14 T AKING SIDE MOTION OUT OF OVER-ARM 1. Loosen hex nuts (A) and gib adjusting scr ews (B) and (C) Fig. 31. 2. Loosen nuts (D) Fig. 31, and adjust bolts (E), so that base wraps around column secur ely . If column is tight in base, turn bolts (E) clockwise to loosen. IMPORT ANT : T ur ning bolts (E) clockwise will open the base jaws, while turning [...]

  • Page 15

    15 Fig. 33 Fig. 34 G ADJUSTING TRACK RODS Each track rod (A, B, C, D) Fig. 34 can be adjusted individually to present a new bearing surface. Adjust the track rods one at a time as follows: 1. Remove end cap (E) Fig. 35, cross-cut stop (F) and cutterhead assembly (G), from the track-arm (Fig. 35). 2. Loosen series of top screws (H) Fig. 35 just enou[...]

  • Page 16

    16 ADJUSTING BLADE SQUARE WITH T ABLE TOP 1. Remove blade guard and place saw blade in cut-of f position over fixed portion of table. 2. Place a square (A) Fig. 36, against saw blade. Be sure squar e is on the table surface, and between the gullets of the teeth, not against the saw teeth. 3. Loosen bevel clamp handle (B) Fig. 36, and loosen two scr[...]

  • Page 17

    17 1. Place a square (A) Fig. 40 against fence (B), and lower cuttinghead (C) so that saw blade just clears table top. 2. Pull cuttinghead (C) Fig. 40, along square (A). If saw blade does not travel parallel to the square, the following adjustment is necessary . 3. Remove cover plate (D) Fig. 41. 4. Locate center cap screw (E) Fig. 41 inside pivot [...]

  • Page 18

    18 Even though the cuttinghead travel may be perfectly aligned at 90 degrees to the fence, the blade itself may not be 90 degrees or squar e with the fence, (Fig. 42). This condition is known as "heeling."T o check and adjust: 1. Cross-cut a board and see on which side of the cut board saw teeth marks appear . 2. If saw teeth marks appear[...]

  • Page 19

    19 ADJUSTING BLADE GUARD On all ripping and plowing operations, the back part of the blade guard is lower ed so that it just clears the material. This will prevent the material fr om being lifted off the table. Also, lower the kickback r od (A) Fig. 46, so that the kickback fingers are 1/8" below surface of material. The kickback fingers will [...]

  • Page 20

    20 ADJUSTING TENSION ON CUTTINGHEAD RETURN ASSEMBL Y The cuttinghead return assembly is properly tensioned when ther e is just enough cable tension to return the cuttinghead (A) Fig. 49, without excessive force, to the r ear of the track arm (B) after completion of the cut. T o adjust: 1. T o INCREASE cable tension, turn adjustment dial (C), Fig. 4[...]

  • Page 21

    21 CROSS-CUTTING Cross-cutting consists of supporting the workpiece against the fence and pulling the saw blade through the material at right angles to it. When cross-cutting, the track arm should be indexed at “0” and the track arm clamp handle tightened. The fence should be clamped between the table boards. The saw blade is to be to the left [...]

  • Page 22

    22 COMPOUND MITER CUTTING Compound miter cutting is performed in the same manner as miter cutting except the saw blade is also tilted to cut a bevel. The settings and operation ar e similar to miter cut ting except that the blade is first tilted to the desired angle on the bevel scale befor e it is clamped in place. Fig. 55 shows a compound miter c[...]

  • Page 23

    23 PUSH STICK Make from 1/2 ″ OR 3/4 ″ WOOD or thickness less than width of material to be cut. Cut her e to push 1/4 ″ wood. Cut her e to push 1/2 ″ wood. Notch to help pr event hand fr om slipping 1/2 ″ Squar es CONSTRUCTING A PUSH STICK When ripping work less than 4 inches wide, a push stick should be used to complete the feed and coul[...]

  • Page 24

    24 TROUBLESHOOTING GUIDE For assistance with your tool, visit our website at www .deltamachinery .com for a list of service centers or call the DEL T A Machinery help line at 1-800-223-7278 (In Canada call 1-800-463-3582). MAINTENANCE P AR TS, SERVICE OR WARRANTY ASSIST ANCE All Delta Machines and accessories are manufactur ed to high quality stand[...]

  • Page 25

    A complete line of accessories is available from your Delta Supplier , Porter -Cable • Delta Factory Service Centers, and Delta Authorized Service Stations. Please visit our W eb Site www .deltamachinery .com for a catalog or for the name of your nearest supplier . Since accessories other than those offer ed by Delta have not been tested with thi[...]

  • Page 26

    26 NOTES[...]

  • Page 27

    27 NOTES[...]

  • Page 28

    The following are trademarks of POR TER-CABLE • DEL T A (Las siguientes son marcas registradas de POR TER-CABLE • DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE • DEL T A): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’ s Saw ® , Contractor’ s Saw ® , Contractor’ s Saw II™, Delta ® , DEL T[...]