English dropdown-ico

Poulan Pro 428707 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Poulan Pro 428707, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Poulan Pro 428707 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Poulan Pro 428707. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Poulan Pro 428707 should contain:
- informations concerning technical data of Poulan Pro 428707
- name of the manufacturer and a year of construction of the Poulan Pro 428707 item
- rules of operation, control and maintenance of the Poulan Pro 428707 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Poulan Pro 428707 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Poulan Pro 428707, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Poulan Pro service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Poulan Pro 428707.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Poulan Pro 428707 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    OWNER'S MANUAL MODEL NUMBER: 961940008 SNOW THROWER Always W ear Eye Protection During Operation IMPORT ANT MANU AL Do Not Throw Away W ARNING: Read the Owner's Manual and fol low all W arnings and Safety In struc tions. F ail ure to do so can result in serious injury . 428707 10.21.09 SR Printed in U.S.A.[...]

  • Page 2

    2 IMPORT ANT Safe Operation Practices for W alk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. F ailure to observe the following safety instructions could result in serious injury . WARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces. Caution should be e[...]

  • Page 3

    3 6. When cleaning, repairing or inspecting the snow thrower , stop the engine and make certain the collector/impeller and all moving parts have stopped. Disconnect the spark plug wire and keep the wire away from the plug to prevent someone from accidentally starting the en- gine. 7. Do not run the engine indoors, except when starting the engine an[...]

  • Page 4

    4 P ARTS P ACKED SEP ARA TEL Y IN CARTON AS SEMBL Y / PRE-OPERA TION Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower . Reading the entire manual will familiar- ize you with the unit, which will assist you in assembly , operation and maintenance of the product. Y our new snow th[...]

  • Page 5

    5 AS SEMBL Y / PRE-OPERA TION SPEED CON TROL ROD SPEED CONTROL BRACKET RET AINER SPRING SPEED CONTROL LEVER FIG. 2 SPEED CONTROL ROD HANDLE KNOB L OWER HANDLE PL ASTIC TIE UPPER HANDLE FIG. 1 INST ALL TRACTION DRIVE CONTROL ROD (See Figs. 3 and 4) The traction drive control rod is installed on the snow thrower . 1. Remove plastic tie securing rod t[...]

  • Page 6

    6 AS SEMBL Y / PRE-OPERA TION AUGER CONTROL LEVER AUGER CONTROL ROD AUGER CONTROL BRACKET RET AINER SPRING FIG. 6 INST ALL AUGER CONTROL ROD (See Figs. 5 and 6) 1. Retrieve vinyl sleeve and spring from bag of parts and retrieve the auger control rod from carton chute tray . Slide straight rod end through the small hole in the vinyl sleeve. Hook spr[...]

  • Page 7

    7 OPERA TION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERA TING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your snow thrower or in literat[...]

  • Page 8

    8 OPERA TION ON / OFF switch - used to STOP the engine. T raction drive control lever - used to engage power - pro pelled for ward or reverse motion of snow thrower . Auger control lever - used to engage auger motion (throw snow). Discharge chute control knob - used to change the di rec tion the snow is thrown. Skid plate - used to adjust height of[...]

  • Page 9

    9 The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your snow thrower or performing any ad just- ments or repairs. We recommend standard safe ty glasses or a wide vision safety mask worn over spectacles. HOW TO USE YO[...]

  • Page 10

    10 TO MOVE FORWARD AND BACK WARD (See Fig. 15) SELF-PROPELLING, forward and reverse movement of the snow thrower , is controlled by the traction drive control lever located on the left side handle. • Squeeze traction drive control lever to handle to en gage the drive system. • Release traction drive control lever to stop the forward or reverse [...]

  • Page 11

    11 TO ADJUST SKID PL A TES (See Fig. 16) NOTE: The wrench provided in your parts bag may be used to adjust the skid plates. Skid plates are located on each side of the auger housing and adjust the clearance between the scraper bar and the ground surface. Adjust skid plates evenly to proper height for current surface conditions. For removal of snow [...]

  • Page 12

    12 OPERA TION SNOW THROWING TIPS • Go slower in deep, freezing or heavy wet snow . Use the drive speed control, NOT the ON / OFF switch, to adjust speed. • It is easier and more efficient to remove snow im me- di ate ly after it falls. • The best time to remove snow is the early morning. At this time the snow is usually dry and has not been e[...]

  • Page 13

    13 GENERAL REC OM MEN DA TIONS The warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. T o receive full value from the warranty , operator must maintain snow thrower as in struct ed in this manual. Some ad just - ments will need to be made periodically to properly maintain your snow thrower[...]

  • Page 14

    14 MAINTENANCE AUGER GEAR CASE • The gear case was filled with lubricant to the proper level at the factory . The only time the lubricant needs attention is if service has been performed on the gear case. • If lubricant is required, use only Ronex ED #1 grease. TRACTION DRIVE SYSTEM DO NOT lubricate the drive components inside the snow thrower [...]

  • Page 15

    15 3. Align holes in impeller hub with holes in impeller shaft and install two (2) new 1/4-20 x 1-5/8" capscrew/shear bolts. Install 1/4-20 locknuts and tighten securely . CAUTION: Do not substitute. Use only original equip ment capscrew/shear bolts as sup plied with your snow thrower . 4. Insert safety ignition key and reconnect spark plug wi[...]

  • Page 16

    16 SERVICE AND ADJUSTMENTS 8. RELIEVE TENSION ON TRACTION DRIVE BEL T IDLER and remove traction drive belt from around pulleys. HINT : Insert a 3/8" drive ratchet (in the “ON” position) into the square hole in idler arm and rotate ratchet clockwise to relieve tension. 9. With tension relieved on idler , install new traction drive belt arou[...]

  • Page 17

    17 SERVICE AND ADJUSTMENTS TO REMOVE WHEELS (See Fig. 21) • Remove the klik pin and remove wheel from axle. IMPORT ANT : When installing wheel, be sure to use the in- nermost hole in axle and the wheel hub hole. T o dis en gage drive system from the wheels (for pushing or trans port ing the snow thrower), remove klik pin from wheel hub and insert[...]

  • Page 18

    18 STORAGE Immediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more. WARNING: Never store the snow thrower with gaso line in the tank in side a build ing where fumes may reach an open flame, spark or pilot light as on a fur nace, water heater , clothes dryer or gas ap pli ance. Allow the[...]

  • Page 19

    19 Does not start 1. F uel shut-off valve (if so 1. T urn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition switch OUT . 2. Push safety ignition switch IN. 3. Out of fuel. 3. Fill fuel tank with fresh, clean gasoline. 4. Throttle in STOP position. 4. Move throttle to F AST position. (or ON/OFF switch is OFF). 5. Ch[...]

  • Page 20

    38 REP AIR P ARTS SNOW THROWER - MODEL NUMBER 96194000801 A UGER HOUSING / IMPELLER AS SEMBL Y NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . 10 11 11 11 11 [...]

  • Page 21

    39 REP AIR P ARTS SNOW THROWER - MODEL NUMBER 96194000801 A UGER HOUSING / IMPELLER AS SEMBL Y NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . [...]

  • Page 22

    40 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION 1 2 3 (5x) 4 (5x) 01.07.001-A 1 404928X428 [...]

  • Page 23

    41 1 1 2 3 2 3 01.07.024-B NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION 1 2 3 4 4 3 01.11.0[...]

  • Page 24

    42 REP AIR P ARTS SNOW THROWER - MODEL NUMBER 96194000801 CONTROL P ANEL / DISCHARGE CHUTE 1 2 3 4 5 6 6 7 8 9 11 11 11 10 01.09.001-B KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be haza[...]

  • Page 25

    43 REP AIR P ARTS SNOW THROWER - MODEL NUMBER 96194000801 CONTROL P ANEL / DISCHARGE CHUTE KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void you[...]

  • Page 26

    44 REP AIR P ARTS SNOW THROWER - MODEL NUMBER 96194000801 HANDLES NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . DESCRIPTION 10 11 1 2 3 [...]

  • Page 27

    45 REP AIR P ARTS SNOW THROWER - MODEL NUMBER 96194000801 HANDLES NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . DESCRIPTION KEY P ART NO[...]

  • Page 28

    46 REP AIR P ARTS SNOW THROWER - MODEL NUMBER 96194000801 HANDLES KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . 10 10 10 1 2[...]

  • Page 29

    47 REP AIR P ARTS SNOW THROWER - MODEL NUMBER 96194000801 HANDLES KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . 1 4 4 5 5 2 [...]

  • Page 30

    48 REP AIR P ARTS SNOW THROWER - MODEL NUMBER 96194000801 DRIVE NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . 9 9 11 11 11 1 2 3 21 5 6 12 13 14 15 20 15 16[...]

  • Page 31

    49 REP AIR P ARTS SNOW THROWER - MODEL NUMBER 96194000801 DRIVE NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . DESCRIPTION KEY P ART NO .[...]

  • Page 32

    50 REP AIR P ARTS SNOW THROWER - MODEL NUMBER 96194000801 DRIVE NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . 1a 1b 1b 4 3 3 4 5 6 6 7 5 2 01.03.005-B KEY P[...]

  • Page 33

    51 REP AIR P ARTS SNOW THROWER - MODEL NUMBER 96194000801 CHAS SIS / ENGINE / PULLEYS KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do s[...]

  • Page 34

    52 REP AIR P ARTS SNOW THROWER - MODEL NUMBER 96194000801 CHAS SIS / ENGINE / PULLEYS 10 11 1 2 3 4 5 6 7 9 8 12 13 14 14 14 15 16 17 18 19 20 20 21 21 22 23 24 01.21.003-B KEY P ART NO . NO . DESCRIPTION KEY P ART NO . NO . DESCRIPTION NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Ma[...]

  • Page 35

    53 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO . DESCRIPTION REP AIR P ARTS SNOW THROWER - MODEL NUMBER 96194000801 WHEELS 1 2 01.06.001[...]

  • Page 36

    54 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . REP AIR P ARTS SNOW THROWER - MODEL NUMBER 96194000801 BAG OF P ARTS KEY P ART NO . NO . DESCRIPTION KEY P [...]

  • Page 37

    55 REP AIR P ARTS SNOW THROWER - MODEL NUMBER 96194000801 DECALS 1 181037 DECAL, DANGER 3 181035 DECAL, DANGER, DEFLECTOR 4 181042 DECAL, DANGER - - 428707 OWNER’S MANUAL, ENGLISH / SP ANISH NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ail[...]

  • Page 38

    LIMITED W ARRANTY The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and work man ship. For a period of two (2) years from date of purchase by the original consumer pur - chaser , we will repair or replace, at our option, without charge for parts or labor incurred in repl[...]