English dropdown-ico

Raypak D-2 POWER VENT 206A manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Raypak D-2 POWER VENT 206A, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Raypak D-2 POWER VENT 206A one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Raypak D-2 POWER VENT 206A. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Raypak D-2 POWER VENT 206A should contain:
- informations concerning technical data of Raypak D-2 POWER VENT 206A
- name of the manufacturer and a year of construction of the Raypak D-2 POWER VENT 206A item
- rules of operation, control and maintenance of the Raypak D-2 POWER VENT 206A item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Raypak D-2 POWER VENT 206A alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Raypak D-2 POWER VENT 206A, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Raypak service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Raypak D-2 POWER VENT 206A.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Raypak D-2 POWER VENT 206A item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    INST ALLA TION & OPERA TING INSTR UCTIONS SWIMMING POOL & SP A HEA TER D-2 Catalog No. 6000.57.1D Effective: 05-21-10 Replaces: 10-26-06 P/N 241243 Rev . 3 W ARNING: If these instructions are not followed exactly , a fire or explosion may result causing property damage, personal injury or death. Do not store or use gasoline or other flammab[...]

  • Page 2

    2 Rev . 3 reflects the following: Changes to: Parts photos on page 3, dimensional illustration on page 4, Fig. 1 and Fig. 3 on page 5, Illustrated Parts List on page 19[...]

  • Page 3

    3 RECEIVING EQUIPMENT On receipt of your equipment, it is suggested that you visually check for external damage to the carton. If the carton is damaged, it is suggested that a note be made on the Bill of Lading when signing for equipment. Remove the complete assembly from the carton. If it is damaged, report the damage to the carrier immediate- l y[...]

  • Page 4

    4 INST ALLA TION REQUIREMENTS Failure to install, maintain and/or operate the Power V ent in accordance with manufacturer ʼ s instructions may result in conditions which can produce bodily injury and property damage. The equipment must be installed by a qualified installer in accordance with all local codes, or , in the absence of local codes, wit[...]

  • Page 5

    5 INST ALLA TION 1 . Start off by disconnecting main power to the heater . 2. Remove the front door from the heater . See Fig 1. 3. If this is a retro-fit application, remove existing “Pagoda T op” and discard. See Fig. 2. If equipped with a drafthood, refer to drafthood installation manual for removal process. 4 . Remove the (6) Phillips screw[...]

  • Page 6

    6 INST ALLA TION (Continued) 6 . Lower the jacket top back onto the heater and reinstall the (6) Phillips screws. See Fig. 3. 7. If installing on a model 266, 267, 406 or 407 heater , skip step 8. 8. T urn t he Po wer V ent u psi de do wn . Usi ng a 5/ 16” n ut dr iv er , re loc ate t he mo un tin g bra cke ts as s ho wn in F ig. 8 . 9. Place the[...]

  • Page 7

    7 INST ALLA TION (Continued) 1 3. Install the right side outdoor conduit through the top 7/8” hole located on the right side of the heater . See. Fig. 13. Note: Y ou must first remove the 7/8” plug on the heater to install the hard conduit. 14. Wire the heater power lines along with the D-2 Power V ent power lines to the supply power per the wi[...]

  • Page 8

    8 INST ALLA TION (Continued) 1 9. Route the 24 V AC harness through the 7/8” grommet, See Fig. 17. 20. Continue to route the harness down through any available grommet hole. See Fig. 18. 21. Wire the harness along with the installed gas valve harness per the wiring diagram. 22. Reinstall the (4) Phillips screws that hold the control panel to the [...]

  • Page 9

    9 U.S. Ins tallations 1 Canad ian Inst alla tions 2 A Clear ance above gr ade , veranda, p orch , deck, or balco ny 1 ft (30 c m) 1 ft (30 c m) B Clear ance to window or do or that may b e o pened 4 ft (1.2 m) below or to side of opening; 1 foo t (30 c m) a bove op ening 3 ft (91 cm) C Clearance to perma nen tly closed window ** D V ertical clearan[...]

  • Page 10

    10 VENTING (Continued)[...]

  • Page 11

    11 VENTING (Continued)[...]

  • Page 12

    12 VENTING (Continued)[...]

  • Page 13

    13 VENTING (Continued)[...]

  • Page 14

    14 SEQUENCE OF OPERA TION On call for heat, the PC board will go through its safety chain (water pressure switch, high limit 1 & 2, roll-out, etc.). When the safety chain is closed, the IID pilot will begin to spark and the pilot gas valve will open. A flame will be lit at the pilot assembly . When an acceptable signal is sent back to the PC bo[...]

  • Page 15

    15 WIRING (Continued) STEP 1 : VERIFY CURRENT CONNECTIONS AS SHOWN BELOW . P/PV C/ M/MV MV PV R/BK Y/BK Y/BK V/BK V/BK V/BK Y/BK G/BK P4 1 RELA Y D-2 POWER VENT Y/BK HONEYWELL V AL VE Y/BK V/W V/BK HONEYWELL V AL VE PV MV M /MV C/ P/PV STEP 2 : DISCONNECT BOTH TERMINALS MVPV & MV AS SHOWN BELOW . D-2 POWER VENT V/BK V/W Y/BK Y/BK R/BK Y/BK V/BK[...]

  • Page 16

    16 WIRING (Continued) MODELS 206, 266, 336, 406 EQUIPPED WITH HONEYWELL GAS V A LV E V/W V/BK V/BK G/BK R/BK 1 P4 D -2 POWER VENT P/PV C/ M/MV MV PV HONEYWELL V AL VE STEP 4 : CONNECT THE MAIN V AL VE LINE, FEMALE SP ADE TO MALE SP ADE AS SHOWN BELOW . D-2 POWER VENT V/BK Y/BK V/W V/BK R/BK P4 1 G/BK STEP 3 : CONNECT THE RETURN LINE, FEMALE SP ADE [...]

  • Page 17

    17 WIRING DIAGRAM – MODELS 207A, 267A, 337A, 407A POWER VENT D-2 D-2 BLOWER POWER VENT GAS V AL VE HONEYWELL 1 1 + -[...]

  • Page 18

    18 WIRING DIAGRAM – MODELS 206A, 266A, 336A, 406A POWER VENT D-2 D-2 BLOWER POWER VENT + - 1 1 TH TR[...]

  • Page 19

    19 REPLACEMENT P ARTS NOTE: T o supply you with the correct part, it is impor- tant that you supply the heater model number , serial number and type of gas when applicable. Any part returned for replacement under standard c ompany warranties must be properly tagged with a return parts tag, completely filled in with the heater serial number , model [...]

  • Page 20

    20 w w w .r ay pak .co m Raypak, Inc., 2151 Eastman Avenue, Oxnard, CA 93030 (805) 278-5300 Fax (805) 278-5468 Litho in U.S.A.[...]