Sharp PG-M20S manual

DIGIT AL MUL TIMEDIA PR OJECT OR OPERA TION MANU AL MODEL PG-M20S Introduction Setup and Connections Basic Operation Easy to Use Functions Appendix[...]

This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC as amended by 93/68/ EEC. Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und 73/23/EWG mit Änderung 93/ 68/EWG. Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE modifiées par la directive 93/68/CEE[...]

SPECIAL NO TE FOR USERS IN THE U.K. The mains lead of this product is fitted with a non-r ewireable (moulded) plug incorporating a 10A fuse. Should the fuse need to be replaced, a BSI or AST A approved BS 1362 fuse marked or and of the same rating as above, which is also indicated on the pin face of the plug, must be used. Always refit the fuse cov[...]

The supplied CD-ROM contains operation instructions in English, German, French, Swedish, Spanish, Italian, Dutch, Portuguese, Chinese (T raditional Chinese and Simplified Chinese), Korean and Arabic. Carefully r ead through the operation instructions before operating the pr ojector . Die mitgelieferte CD-ROM enthält Bedienungsanleitungen in Englis[...]

Introduction -1 Before using the pr ojector , please read this operation manual carefull y . There ar e two important reasons for prompt warranty r egistration of your new SHARP Projector , using the REGISTRA TION CARD packed with the projector . 1. W ARRANTY This is to assure that you immediately r eceive the full benefit of the parts, service and[...]

-2 W ARNING: The cooling fan in this projector continues to run for about 90 seconds after the pr ojector is turned off. During normal operation, when tur ning the power off always use the PO WER button on the projector or on the remote control. Ensure the cooling fan has stopped befor e disconnecting the power cor d. DURING NORMAL OPERA TION, NEVE[...]

Introduction -3 Outstanding Features 1. Ima g e Quality • Superior image quality with Fujinon™ optical lens system • Newl y de veloped DDR (Double Data Rate) c hip eliminates Color Break- ing phenomena common with pre vious generation DLP™ projector s. • Newl y de veloped 12 ° DMD™ chip pr ovides significantl y impr oved opti- cal effi[...]

-4 Contents Adjusting the Picture ........................................ 40 Adjusting Image P r efe r ences ................................. . 40 Selecting the Signal T ype ....................................... 40 P r og r essive Mod e ................................................... . 41 Adjusting Computer Images ..........................[...]

Introduction -5 Setting the Anti-Thef t ........................................ 63 Entering the Keycode ............................................. . 63 Changing the Keycode .......................................... . 64 Initializing the Settings ..................................... 65 Displ a ying the Adjustment Setting s ................ 66 [...]

-6 1. Read Instructions All the safety and operating instructions should be read before the pr oduct is operated. 2. Retain Instructions The safety and operating instructions should be retained for futur e refer ence. 3. Heed W arnings All warnings on the product and in the operating instructions should be adhered to. 4. Follow Instructions All ope[...]

Introduction -7 18. Damage Requiring Service Unplug this product fr om the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power -supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the product. c. If the product has been exposed to rain or water . d. [...]

-8 IMPOR T ANT SAFEGU ARDS (cont.) Be sur e to read the following safeguar ds when setting up your projector . Caution concerning the lamp unit ■ P otential hazard of glass particles if lamp ruptures. In case of lamp r up- ture, contact y our nearest Sharp Au- thorized Projector Dealer or Service Center f or a replacement. See “ Replacing the L[...]

Introduction -9 PDF operation manuals in se veral languages are included in the CD-R OM. T o utilize these manuals, y ou need to install Adobe Acrobat Reader on y our PC (Windows or Macintosh). If you ha ve not installed Acrobat Reader y et, y ou can download it fr om the Internet (http:// www .adobe.com) or install it from the CD-R OM. T o install[...]

-10 Projector (Front and Top View) Part Names Foot releases/Adjustment feet For adjusting the projector ’ s height. Attaching the terminal cover Attach the terminal cover by placing it on the side panel of the projector and pressing it into place, as shown in the illustration. TEMPERA TURE W ARNING indicator When the internal temperature rises, t[...]

Introduction -11 24 20 69 11 26 21 21 24 Projector (Side View) Exhaust vent AC socket Kensington Security Standard connector Using the Kensington Lock • This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security System. Refer to the information that came with the system for instructions on how to use[...]

-12 Remote Control Part Names (cont.) 28 49 48 30 29 29 29 29 44 32 36 46 36 50 36 33 26 FOR W ARD/BA CK b utton Moves forward or backwards when connected to a computer using a USB cable. Same as the [Page Down] and [Page Up] keys on a computer keyboard. A V MUTE button For temporarily turning off the sound and picture. VOLUME buttons For adjusting[...]

Introduction -13 23' (7 m) 30 ° 30 ° 45 ° Using the Remote Control ■ The remote control can be used to control the projector within the ranges shown in the illustration. Note • The signal from the remote control can be reflected off a screen for easy oper ation. Howe ver , the effectiv e distance of the signal ma y differ due to the scr[...]

-14 Note Accessories Remote control RRMCGA013WJSA T wo R-03 batteries (“AAA” size, UM/SUM-4, HP-16 or similar) Power cord (6' (1.8m)) For U.S., Canada, etc. QACCDA007WJPZ For Europe, except U.K. QACCV4002CEZZ For U.K., Hong Kong and Singapore QA CCBA012WJPZ F or Austr alia, New Zealand and Oceania QACCL3022CEZZ • Depending on the region,[...]

Setup and Connections Setup and Connections[...]

Up Down Foot releases Adjustment feet Setup Using the Adjustment Feet The height of the projector can be adjusted using the adjustment feet when the surface of the projector is placed on is une ven or when the screen is slanted. The projection of the image can be made higher by adjusting the pr ojector when it is in a location lower than the screen[...]

Setup and Connections -17 90 ° 90 ° Example of Standard Setup Setting up the Screen P osition the projector perpendicular to the screen with all f eet flat and level to achieve an optimal ima ge. Note • The projector lens should be centered in the middle of the screen. If the horizontal line passing through the lens center is not per pendicular[...]

-18 Setup (cont.) Screen Size and Projection Distance 90 ° H Screen Base line: Horizontal line passing through the lens center . Lens center L:Projection distance The formula f or picture size and projection distance L1 (ft) = (0.0 62081X – 0.03 8676) / 0.3048 L2 (ft) = (0.0 51456X – 0.038901 ) / 0.3048 H (in) = – 0.084 8X X: Picture size (d[...]

Setup and Connections -19 When using the default setting. ▼ On-screen Display Projecting a Reversed/Inverted Image Pr ojection from behind the screen ■ Place a translucent screen between the projector and the audience. ■ Rev erse the image by setting “ Rear ” in “ PRJ Mode ” . See page 60 f or use of this function. Projection using a [...]

Connecting the Pr ojector to Other De vices Before Connecting Note • Bef ore connecting, be sure to tur n off both the projector and the devices to be connected. After making all connections, turn on the projector and then the other de vices. When connecting a computer , be sure that it is the last de vice to be turned on after all the connection[...]

Setup and Connections -21 1 D VI to 15-pin D-sub cab le Connecting the Projector to a Computer Connecting to a Computer Using the DVI to 15-pin D-sub Cable 1 Connect the pr ojector to the computer using the supplied D VI to 15-pin D-sub cable. • Secure the connectors by tightening the thumbscrews . 2 T o input audio signal, connect the projector [...]

-22 1 D VI cable (sold separately) Connecting the Pr ojector to Other De vices (cont.) Connecting to a Computer Using a DVI Cable (Sold Separately) This projector comes installed with a D VI digi- tal input terminal in which computer digital im- age signals can be directly input. 1 Connect the pr ojector to the computer using the D VI cable. 2 T o [...]

Setup and Connections -23 1 D VI to 15-pin D-sub adaptor (sold separately) Connecting to Video Equipment Connecting to Component Video Equipment Use a 3 RCA to 15-pin D-sub cable and D VI to 15-pin D-sub adaptor when connecting to the INPUT 1 terminal, component video equipment such as D VD play ers and DTV* decoders. *DTV is the umbrella term used[...]

1 S-VIDEO cable (commercially a vailable) Connecting the Pr ojector to Other De vices (cont.) Connecting to Video Equipment Using an S-VIDEO, a Composite Video or an Audio Cable Using an S-VIDEO , video, or audio cable, a VCR, laser disc play er or other audio-visual equipment can be connected to INPUT 2, IN- PUT 3 and A UDIO terminals. 1 Connect t[...]

Setup and Connections -25 T o RGB output por t Connecting to a Monitor Watching Images on Both the Projector and a Monitor Y ou can display computer images on both the projector and a separate monitor using an RGB monitor loop-out adaptor and an RGB cable. 1 Connect the pr ojector to the computer and monitor using an RGB monitor loop-out adap- tor [...]

FOR W ARD/BA CK button Connecting the Pr ojector to Other De vices (cont.) Using the Wireless Presentation Function of the Remote C ontrol The Wireless Presentation function on the pr ojector works the same as the [P age Up] and [P age Down] keys on a computer ke yboard. It can also be used to mo ve forward or bac kwar d when viewing ima g es of pr[...]

Basic Operation Basic Operation[...]

Image Projection Basic Procedure Connect the required external equipment to the projector before operating the following procedures. The language preset at the factory is English. If you want to change the on-screen display to another language, reset the language ac- cording to the procedure on page 30 . 1 Plug the power cor d into the wall outlet.[...]

Basic Operation -29 " On-screen Display (Example) ➝ ➝➝ Using Analog RGB Using Component INPUT 2 Mode Using S-Video INPUT 3 Mode Using Video 3 Press , or on the re- mote contr ol to select the IN- PUT Mode. • After pressing once, use the b ut- ton to select the desired INPUT Mode. Note • When no signal is received, “ NO SIGNAL ” w[...]

Image Projection (cont.) POWER button 5 Press to temporaril y turn off the picture and sound. Note • Pressing again will turn the pic- ture and the sound back on. 6 Press , then press again while the confirmation message is displayed, t o turn off the pro- jector . Note • If you accidentally pressed and do not want to turn off the power , wait [...]

Basic Operation -31 Zoom in Z o o m o u t 3 Press or to select the desired language, and then press . 4 Press . • The desired language will be set as the on-screen displa y . Adjusting the Lens The image is focused and adjusted to the desired size using the focus ring or zoom knob on the projector . 1 The focus is adjusted by rotat- ing the focus[...]

Correcting T rapezoidal Disto r tion ( K e ystone Correction ) Correcting Trapezoidal Distortion This function allows for Keystone (On-screen T rapezoidal Distortion) Correction. Note • Keystone Correction is the correction for trapezoidal distortion that occurs when the image is positioned away from the center axis of the screen. • The trapezo[...]

Basic Operation -33 • The Digital Shift function works with BORDER, STRETCH or SMART STRETCH screen. For details, see page 47 . Digital Shift Setting For easier viewing, this function shifts the entire image projected on the screen up or down when projecting 16:9 images from DVD players and DTV* decoders. * DTV is the umbrella term used to descri[...]

-34 Menu Bar Items This list shows the items that can be set in the pr ojector . ■ INPUT 1 Mode Page 66 Note • The resolution, vertical frequency and horizontal frequency figures displayed above are for example pur poses only . • When D VI digital signals hav e been entered into INPUT 1, in “ Picture ” only “ CLR T emp ” , “ Red ”[...]

Basic Operation -35 ■ INPUT 2 / 3 Mode +30 – 30 +30 – 30 +30 – 30 +30 – 30 +30 – 30 +30 – 30 +30 – 30 +3 – 3 English Deutsch Espa ñ ol Nederlands Fran ç ais Italiano Svenska Portugu ê s Picture Options (1) Contrast Bright Color Tint Sharp Red Blue CLR T emp Reset Progressive Mode Power Save [ON/OFF] Auto Search [ON/OFF] DNR OSD[...]

This projector has two sets of menu screens that allow you to adjust the image and various projector settings. Y ou can operate the menus fr om the projector or remote contr ol using the following pr oce- dure. Using the Menu Screen On-screen menu for INPUT 1 RGB mode On-screen menu for INPUT 2 or INPUT 3 Mode Menu Bar (Main Menu) MENU button butto[...]

Basic Operation -37 2 Press or to select the menu you want to adjust. Note • For details on the menus, see the tree charts on pages 34 and 3 5 . 3 Press or to select the item you want to adjust. Note • T o display a single adjustment item, press after selecting the item. Only the menu bar and the selected adjustment item will be displayed. Then[...]

MENU button b uttons ENTER button MENU button buttons ENTER button ▼ On-screen Display Basic Operations (Settings) 1 Press . Note • The “ Picture ” menu screen for the selected input mode is displayed. • The on-screen display shown on the right is display ed when INPUT 1 mode is selected. 2 Press or to select the menu you want to adjust. [...]

Basic Operation -39 4 Press . • The cursor shifts to the sub menu. 5 Press or to select the setting of the item displayed in the sub menu. 6 Press . • The item selected is set. Note • Some adjustment items will display a confirmation message. When setting an item, press or to select “ Ye s ” or “ OK ” and then press . 7 Press . • Th[...]

Adjusting the Picture Y ou can adjust the projector’ s picture to y our preferences with the f ollowing picture settings. Selected Item Description button button Contrast Bright Color Tint Sharp Red Blue CLR T emp For adjusting the contrast level For adjusting the brightness of an image For adjusting the color intensity of the image For adjusting[...]

Basic Operation -41 Progressive Mode This function allows you to select the pro- gressive display of a video signal. The pro- gressive display projects a smoother video image. Select “ Progressive Mode ” in the “ Pic- ture ” menu ➝ For settings, see page 38 . Note • 2D Progressive This function is useful to display fast- moving images s[...]

Adjusting Computer Images Use the Fine Sync function in case of irregularities such as vertical stripes or flickering in portions of the screen. When Auto Sync is OFF When “ Auto Sync ” is “ OFF ” , interference such as flickering or vertical stripes may oc- cur if displaying tilings or vertical stripes. Should this occur , adjust “ Cloc [...]

Basic Operation -43 Selecting Adjustment Settings Adjustment settings stored in the projector can be easily accessed. Select “ Select Setting ” in the “ Fine Sync ” menu ➝ For details, see page 38 . Note • If a memory position has not been set, a resolution and frequency setting will not be displayed. • When selecting a stored adjustm[...]

Auto Sync Adjustment Used to automatically adjust a computer im- age. Select “ Auto Sync ” in the “ Fine Sync ” menu ➝ For settings, see page 38 . Note When setting to “ Normal ” or “ High Speed ” : • Auto Sync adjustment will occur when the projector is turned on or when the inputs are switched, when connected to a com- puter .[...]

Easy to Use Functions Easy to Use Functions[...]

46 Selecting the Picture Displa y Mode Switching the Picture Display Using Different Input Signals 1 Press . • Each time is pressed, the displa y changes as sh o wn on page 4 7 . Note • In the Dot by Dot Mode , images are dis- play ed in the original resolution, theref ore they will not be enlarged. • T o return to the standard image, press w[...]

Easy to Use Functions -47 4:3 aspect ratio Other aspect ratios SVGA (800 × 600) XGA (1024 × 768) SXGA (1280 × 960) SXGA (1280 × 1024) NORMAL 800 × 600 800 × 600 800 × 600 750 × 600 FULL — — — 800 × 600 D O T BY D O T — 1024 × 768 1280 × 960 1280 × 1024 480 I , 480P , NTSC P AL, SECAM 720P , 1080 I 4:3 aspect ratio. Letter box, s[...]

48 Storing an Image in Still Image Format 1 Press . • The projected image is frozen. 2 Press again to return to the moving ima ge from the cur - rently connected de vice. Displa ying a Still Image This function all o ws y ou to instant l y free z e a m o ving im a g e . This is useful when y ou want to display a still ima ge from a computer or vi[...]

Easy to Use Functions -49 Enlarging a Specific P or tion of an Image Displaying an Enlarged Portion of an Image 1 Press . • Enlarges the image. • Pressing or enlarges or re- duces the projected image. Note • Y ou can change the location of the enlarged image using , , or . • When an image with a resolution higher than XGA is displa yed, “[...]

50 Selected Mode ST ANDARD PRESENT A TION CINEMA GAME Description F or Standard picture Brightens darker por tions of image for more enhanced presentations . Giv es greater depth to darker por tions of image f or a more exciting theater e xper ience. Natural color gr adation for pla ying a game, etc. Gamma Correction Function Gamma is an image qual[...]

Easy to Use Functions -51 Displ a ying Dual Pictures ( Pict in Pict ) Picture in Picture function allows y ou to displa y two pictures on the same screen. Y ou can display the ima ge input from INPUT 2 or 3 as an inset picture o verlapping the main picture from INPUT 1. (This function can only be set in the RGB menu.) Displaying the Inset Picture S[...]

52 Selecting the P o wer Save Mode The P ower Sa ve Mode or the A utomatic P ower Shutoff function allo ws y ou to reduce the power consumption of the pr ojector . Setting the Power Save Mode Function to control the quantity of pr ojected light. Select “ ON ” or “ OFF ” to decrease or increase brightness and power consumption. Description o[...]

Easy to Use Functions -53 Acti v ating the sRGB Color Man a g ement Function This function calibrates the p r ojecto r ’ s output to con f orm to sRGB standa r d (6,500K). Using Auto Search Select “ A uto Search ” in the “ Options (1) ” me n u ➝ For settings, see p a g e 36 . Note • ON Automatically s witches to the input mode in whic[...]

54 Video Digital Noise Reduction (DNR) System Reducing Image Noise (DNR) Select “ DNR ” in the “ Options (1) ” me n u ➝ For settings, see p a g e 38 . Note • Set a le vel so as to vie w a clearer picture. Make sure to set DNR to “ OFF ” in the f ol- lowing cases: • When the image is blurry . • When the contours and colors of mov[...]

Easy to Use Functions -55 Setting the Video System Setting the Video System Select “ Video System ” in the “ Options (1) ” me n u ➝ For settings, see p a g e 38 . Note • The video signal can only be set in IN- PUT 2 or INPUT 3 mode. • In “ A uto ” , images are displa yed in P AL e ven if P AL-N or P AL-M input signals are received[...]

56 Sa ving Pr ojected Images • This pr ojector allows y ou to capture projected ima ges (RGB signals) and set them as a startup image, or bac kground ima ge when no signals are being received. • Y ou can capture the images that are input using analog RGB signals and Digital D VI SV GA signals. Capturing the Image Select “ Image Capture ” in[...]

Easy to Use Functions -57 Setting a Ba c kg r ound Im a g e This function allows y ou to select the image displa yed when no signal is being sent to the projector . *1 Y ou can set a captured image as a background image b y selecting “ Custom ” . *2 If the input signal has interf erence, the screen will be displa y ed with the interference . Se[...]

58 Lamp Usage Time Using an RGB monitor loop-out adaptor (sold separatel y) and an RGB cable (commerciall y av ailable), be sure to set to “ Y es (Y Cable) ” when you want to displa y computer images both on the pr ojector and on a monitor . Using a RGB Monitor Loop-out Adaptor Select “ Monitor Out ” in the “ Options (1) ” me n u ➝ Fo[...]

Easy to Use Functions -59 Displa ying the Break Timer " On-screen Display Displaying and Setting the Break T imer Select “Break Timer” from the “Options (2)” me n u ➝ For details, see p a g e 36 . 1 When “ ” is display ed, press or to set the Break Timer . • Y ou can set anywhere between 1 and 60 minutes (in 1 minute units). 2 [...]

Reversing/Inverting Projected Images This projector is equipped with a re verse/in ver t image function that allows y ou to rever se or in vert the projected image f or various applications. Setting the Pr ojection Mode Select “ PRJ Mode ” in the “ Options (2) ” menu ➝ For settings, see page 3 8 . Note • If a password has been set, the [...]

Easy to Use Functions -61 Canceling the Keylock Setting When the Keylock Level is set to “ Normal ” , all buttons are functional. Select “ K eylock Le vel ” in the “ Options (2) ” menu and set “ Normal ” . ➝ For settings, see page 38 . Note • When a password has been set, and “ Keylock Level ” is selected, the password input[...]

Changing the Passwor d Select “ Password ” in the “ Options (2) ” menu ➝ For selecting, see page 38 . 1 Press , and to enter the password in “ Old Pass- word ” and press . 2 Press , and to set the new pass wor d and press . 3 Enter the new 4-digit password again in “ Reconfirm ” and press . Note • If you do not want to set a pas[...]

Easy to Use Functions -63 Setting the Anti-Theft The anti-theft function prevents unauthorized use of the pr ojector . Y ou can choose to use this function or not. If y ou do not want to use this function, just do not enter the ke ycode. Once the theft-deterrent function is activ ated, users will need to enter the correct ke ycode each time the pro[...]

Setting the Anti-Theft (cont.) When “ Anti-Theft ” is set, the keycode inputting section appears after the power is turned on. At that time , enter the right keycode. • Press the buttons on the remote control if the buttons on the remote control are used f or setting the ke ycode. In the same manner , press the buttons on the projector if the[...]

Easy to Use Functions -65 Initializing the Settings This function allows y ou to initialize the settings y ou have made in the pr ojector . Retur ning to the Default Settings Select “ All Reset ” in the “ Options (2) ” menu ➝ For resetting, see page 36 . Note • If a password has been set, the pass- word input box will be displayed when [...]

This function can be used to display all the adjusted settings as a list on the screen. Displa ying the Adjustment Settings Over view of All Menu Setting Select the “ Status ” me n u and press ➝ For details, see page 36 . -66[...]

Appendix Appendix[...]

Carrying the Projector How to Use the Carr ying Case When carrying the projector , attac h the lens cap to the lens, and place it in the included carrying case. 1 Open the cover of the carrying case. 2 Remove the inner pad ding from the carrying case, and fold it in the direction of the arr ows. 3 Reinsert the inner padding into the carrying case .[...]

Appendix -69 Cleaning the lens ■ Use a commercially av ailable b low er or lens cleaning paper (for glasses and camer a lenses) for cleaning the lens . Do not use any liquid type cleaning agents, as the y may w ear off the coat- ing film on the surf ace of the lens. ■ As the surface of the lens can easily get dam- aged, be sure not to scrape or[...]

-70 Maintenance Indicator s Info • If the TEMPERA TURE W ARNING indicator illuminates, and the po wer turns off, f ollow the abo ve possib le solutions and then wait until the projector has cooled do wn completely bef ore plugging in the power cord and tur ning the pow er back on. (At least 5 minutes.) • If the power is turned off and then turn[...]

Appendix -71 Lamp ■ It is recommended that the lamp (sold separatel y) be replaced after appro ximately 1,900 cum ulative hours of use or when y ou notice a significant deterioration of the picture and color quality . The lamp us a g e time can be c he c ked with the on-screen displ a y . See p a g e 58 . ■ For lamp replacement, please consult [...]

PO WER b utton Regar ding the Lamp (cont.) Removing and Install- ing the Lamp Unit Info • Be sure to remov e the lamp unit by the handle. Be sure not to touch the glass surf ace of the lamp unit or the inside of the projector . • T o a void injury to yourself and damage to the lamp , be sure to carefully follo w the steps below . • Do not loo[...]

Appendix -73 A C soc ket PO WER b utton b uttons ENTER b utton User service screw 4 Remove the lamp unit. • Loosen the securing screws from the lamp unit. Hold the lamp unit b y the handle and pull it in the direction of the arrow . 5 Insert the new lamp unit. • Press the lamp unit firmly into the lamp unit compar tment. F asten the secur- ing [...]

-74 1 2 4 3 17 ••••••••• ~ ••••••••• •••• ~ •••• •••• ~ •••• 24 18 23 C3 2 1 9 16 C1 C2 C4 C5 8 7 • D VI Digital RGB Input Pin No. Signal Pin No. Signal 1 T .M.D .S data 2 – 16 Hot plug detection 2 T .M.D .S data 2+ 17 T .M.D .S data 0 – 3 T .M.D .S data 2 shield 18 T .M.D.S [...]

Appendix -75 Computer Compatibility Char t * T emporary noise may be visib le with vertical frequencies above 100Hz if OSD functions are activ ated. Note • This projector may not be ab le to displa y images from notebook computers in simultaneous (CR T/LCD) mode. Should this occur , turn off the LCD display on the notebook computer and output the[...]

-76 T roub leshooting Check • Projector power cord is not plugged into the w all outlet. • P ow er to the e xter nal connected de vices is off. • The selected input mode is wrong. • Cables incorrectly connected to side panel of the projector . • Remote control batteries hav e run out. • External output has not been set when connecting n[...]

Appendix -77 Check Problem Page • The K e ylock le v el is set. If the K eyloc k le vel is set to Le vel B , all the buttons are lock ed. If the K eyloc k le vel is set to Le vel A, only the INPUT , V OLUME and A V MUTE buttons work. • Change the input signal type setting. • The LAMP REPLACEMENT indicator is blinking in red. Replace the lamp.[...]

-78 For SHARP Assistance If you encounter an y pr oblems during setup or operation of this pr ojector , fir st refer to the “T roubleshooting” section on pages 76 and 77. If this operation manual does not ans wer your question, please contact the SHARP Service depar tments listed below . U.S.A. Sharp Electronics Corporation 1-888-GO-SHARP (1-88[...]

Appendix -79 Specifications Digital Multimedia Projector PG-M20S NTSC 3.58/NTSC 4.43/P AL/P AL-M/P AL-N/P AL 60/SECAM/ DTV480 I /DTV480P/DTV720P/DTV1080 I Single Chip Digital Micromirror De vice ™ (DMD ™ ) by T exas Instruments P anel size: 0.55" (14 mm), 1 chip SV GA DMD No . of dots: 480,000 dots (800 [H] × 600 [V]) 1 – 1.2 × zoom le[...]

-80 Side View Side View Top View Rear View Front View Bottom View 11 15 / 16 (303) 1 1 / 2 (38.7) 1 3 / 8 (34.2) 3 9 / 32 (83) 3 (76) 10 5 / 16 (261.5) 4 1 / 8 (104) 3 1 / 8 (80) 5 / 16 (7.5) 12 17 / 32 (318) 8 5 / 8 (219) 5 1 / 16 (128) 4 9 / 16 (115.5) ø54 8 3 / 4 (223) 7 11 / 16 (195) 2 3 / 8 (60) 3 1 / 4 (82.5) 1 31 / 64 (37.5) M3 M3 M3 Units:[...]

Appendix -81 Glossary Advanced intelligent compression High quality resizing of lower and higher resolu- tion images to fit the projector ’ s nativ e resolution. Anti-theft In case the projector is stolen, this function dis- ables projection of images if the correct keycode is not entered. Aspect Ratio Width and height ratio of an image . The nor[...]

-82 2D Progressive .................................................... 4 1 3D Progressive .................................................... 4 1 AC socket ............................................................ 2 0 Adjustment buttons .............................................. 3 6 Adjustment fee t ........................................[...]

SHARP CORPORA TION[...]