English dropdown-ico

Shure SCM410E manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Shure SCM410E, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Shure SCM410E one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Shure SCM410E. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Shure SCM410E should contain:
- informations concerning technical data of Shure SCM410E
- name of the manufacturer and a year of construction of the Shure SCM410E item
- rules of operation, control and maintenance of the Shure SCM410E item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Shure SCM410E alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Shure SCM410E, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Shure service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Shure SCM410E.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Shure SCM410E item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    SCM410/SCM410E FOUR CHANNEL AUT OMA TIC MICROPHONE MIXER Shure Brothers Incorporated 222 Hartrey Avenue Evanston IL 60202-3696 U.S.A. Model SCM410/SCM410E User Guide 27A8690 (SG)  1999, Shure Brothers Incorporated Printed in U.S.A. U.S. Patents 4,658,425; 5,297,210[...]

  • Page 2

    2 T ABLE OF CONTENTS DESCRIPTION 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FEA TURES 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .[...]

  • Page 3

    3 DESCRIPTION The Shure Model SCM410/E is a four-channel automatic mi- crophone mixer designed for use in sound reinforcement, au- dio recording, and broadcast applications. The SCM410 dra- matically improves audio quality in any application where mul- tiple microphones are required. Any low-impedance dynamic or condenser microphone (including wire[...]

  • Page 4

    4 REAR P ANEL MODEL SCM410 REAR P ANEL FIGURE 2 1. Power Connector: Unit is energized when the power cord is plugged into a 100–120 V ac (SCM410) or 220–240 V ac (SCM410E) power source. Can be internally modified.Refer to the “Internal Modification” section. NOTE: There is no power On/Off switch on this mixer . 2. DIP Switch: The 4-position[...]

  • Page 5

    5 INST ALLA TION SUPPLIED HARDW ARE  4 rubber feet  1 rackmount bracket, long  1 rackmount bracket, short  2 straddle brackets  10 bracket screws, 6 mm (1/4 in.)  4 rackmount screws, 2.54 cm (1 in.)  4 plastic washers  4 wood screws, 1.25 cm (1/2 in.) RACK MOUNTING The SCM410 is supplied with hardware for mounting one or two[...]

  • Page 6

    6 T ABLE-TOP MOUNTING Adhere the four (4) supplied rubber feet to the bottom of the mixer at each corner , as shown in Figure 9. This will keep it from sliding and protect the table surface. A TT ACHING RUBBER FEET FOR T ABLE–TOP MOUNTING FIGURE 9 FIXED MOUNTING T op Mount 1. Fasten the straddle brackets to the recessed edges of the chassis, u si[...]

  • Page 7

    7 SCM410 CONNECTIONS 1. Connect microphone signal sources to the Channel Input connectors, as shown in Figure 14. Use conventional 2-con- ductor shielded audio cables. 2. I f any condenser microphones are connected, set the +12V phantom power DIP switch to ON. 3. Connect the SCM410 Mic/Line Level Output to the input of mixers, EQs, amplifiers or re[...]

  • Page 8

    8 BASIC MIXER OPERA TION 1. Adjust each channel level so that its Overload LED flickers only during very loud speech or noise. 2. Adjust the Low-Cut and High-Frequency controls adjacent to each Input Gain control so that the microphones sound similar . 3. Adjust the Master level control for the required output level, as indicated by the output peak[...]

  • Page 9

    9 SPECIFICA TIONS Measurement Conditions (unless otherwise specified): Line voltage 120 V ac, 60 Hz (SCM410) or 230 V ac, 50 Hz (SCM410E); full gain; 1 kHz, one channel activated; source impedances: Mic 150 Ω ; terminations: Line/Mic Aux 10 k Ω Frequency Response (at 1 kHz, channel controls centered) 50 Hz to 20 kHz ± 2 dB; -3 dB corner at 25 [...]

  • Page 10

    10 Replacement Parts Knob, Master (white) 95A8238 . . . . . . . . . . . . . . . . . . . . . . . Knob, Channel Gain (blue) 95B8238 . . . . . . . . . . . . . . . . . Line (Power) Cord (SCM410) 95A8762 . . . . . . . . . . . . . . . Line (Power) Cord (SCM410E) 95A8778 . . . . . . . . . . . . . . Link Cable 95A8889 . . . . . . . . . . . . . . . . . . . [...]

  • Page 11

    11 ADV ANCED FUNCTIONS CAUTION : Use of Advanced Functions is recommended only for qualified audio technicians. LOGIC CONNECTION SPECIFICA TIONS The SCM410 logic functions expand the range of installation an d control options. Logic can be used for everything from sim- ple cough switches to elaborate computer-controlled room systems. (Shure’s AMS[...]

  • Page 12

    12 SUGGESTED LOGIC APPLICA TIONS This section contains suggestions on the uses of the SCM410’s logic capabilities. Note that uses of these functions ar e not limited to the listed applications. The user is limited only by imagination and creativity . For additional suggestions and solutions to installation problems, contact the Shure Applica- tio[...]

  • Page 13

    13 Inhibiting Gating for Unwanted Sounds MaxBus attempts to activate only one microphone per sound source. Muting a microphone channel prevents its audio from appearing at the mixer ’ s output. However , the muted micro- phone still communicates with other mic channels via Max- Bus. A sound source picked up by a muted microphone will not activate[...]

  • Page 14

    14 Inhibit Function For information on the inhibit function, refer to the Internal Modifications section. Remote V olume Control Th e level of the Aux or Master output can be controlled from an external VCA (V oltage Controlled Amplifier) such as the RU- VCA1 from Radio Design Labs (T el. 1–800–281–2683, or www .rdlnet.com). T o connect a VCA[...]

  • Page 15

    15 INTERNAL MODIFICA TIONS W ARNING: V oltages in this equipment are hazardous to life. No user-serviceable parts inside. Refer all servicing to qualified service personnel. NOTE: • Only make changes to jumpers (X) and resistors (R). The circuit board contains holes where resistors are to be added. • For Channel modifications, the first charact[...]

  • Page 16

    16 INSERTING AN INPUT LINE P AD T o insert a 40 dB line pad for a given microphone input, remove the resistors specified in the following table. Channel Remove Resistor 1 R1005, R1006 2 R2005, R2006 3 R3005, R3006 4 R4005, R4006 DISABLING THE MASTER LEVEL CONTROL Th e Master gain control can be disabled to prevent tampering. Refer to the following [...]

  • Page 17

    17 When both MUTE IN and OVERRIDE IN logic are grounded, the Override mode will take precedence (as supplied, the MUTE IN takes precedence over OVERRIDE IN). Procedure: 1. Short jumper X1005. 2. Remove resistor R1087. DEAD ZONE ON MUTE IN DEFEA T As supplied, MUTE IN is intended for use as a momentary cough button or privacy function (mute when nec[...]

  • Page 18

    18 This modification is equivalent to shorting one of the channel OVERRIDE IN t o the LOGIC GROUND pin via the high density DB-15 logic connector . With this modification, a channel is al- ways on. Procedure: Short jumper X1003. SHORTING MUTE IN T O LOGIC GROUND INTERNALL Y This modification is equivalent to shorting a channel MUTE IN to the LOGIC [...]