Go to page of
A good user manual
The rules should oblige the seller to give the purchaser an operating instrucion of Siemens programming the cpu 314c-2dp, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.
What is an instruction?
The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Siemens programming the cpu 314c-2dp one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.
Unfortunately, only a few customers devote their time to read an instruction of Siemens programming the cpu 314c-2dp. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.
What should a perfect user manual contain?
First and foremost, an user manual of Siemens programming the cpu 314c-2dp should contain:
- informations concerning technical data of Siemens programming the cpu 314c-2dp
- name of the manufacturer and a year of construction of the Siemens programming the cpu 314c-2dp item
- rules of operation, control and maintenance of the Siemens programming the cpu 314c-2dp item
- safety signs and mark certificates which confirm compatibility with appropriate standards
Why don't we read the manuals?
Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Siemens programming the cpu 314c-2dp alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Siemens programming the cpu 314c-2dp, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Siemens service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Siemens programming the cpu 314c-2dp.
Why one should read the manuals?
It is mostly in the manuals where we will find the details concerning construction and possibility of the Siemens programming the cpu 314c-2dp item, and its use of respective accessory, as well as information concerning all the functions and facilities.
After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.
Table of contents for the manual
-
Page 1
A utomation and Drive s - SCE T I A Training Document Page 1 of 25 Module Training Document for Comprehensive Automation Solutions Totally Integrated Automation (T I A) MODULE A5 Programming the CPU 314C-2DP A5 Issue date: 02/2008 Programming the CPU 314C-2DP[...]
-
Page 2
A utomation and Drive s - SCE T I A Training Document Page 2 of 25 Module This document has been written by Siemens AG for tr aining purposes for the project entitled "Siemens Automation Cooperates with Education (SCE)". Siemens AG accepts no responsibility fo r the correctness of the contents. Transmission, use or reproduction of this do[...]
-
Page 3
A utomation and Drive s - SCE T I A Training Document Page 3 of 25 Module SEITE: 1. Forew ord .............................................................................................................. 4 2. Notes on Using the CPU 314C-2DP ................................................................... 6 2.1 Operator Control of the CPU 31xC .[...]
-
Page 4
A utomation and Drive s - SCE T I A Training Document Page 4 of 25 Module 1. FOREWORD In terms of its contents, module A5 belongs to the teaching unit entitled "Basic Principles of STEP 7 Programming' . Basic Principles of STEP 7 Programming 2 to 3 days Module A Industrial Field Bus Systems 2 to 3 days Module D Further Functions of STEP 7[...]
-
Page 5
A utomation and Drive s - SCE T I A Training Document Page 5 of 25 Module Hardw are and softw are needed 1 PC, operating system Windows 2000 Professional starting with SP4 /XP Professional starting with SP1/Server 2003 with 600 MHz and 512 RAM, free hard disk memory approx. 650 to 900 MB, MS Internet Explorer 6.0 2 Software: STEP7 V 5.4 3 MPI inter[...]
-
Page 6
A utomation and Drive s - SCE T I A Training Document Page 6 of 25 Module 2. NOTES ON THE USE OF THE CPU 314C-2DP The CPU 314C-2DP is shipped with an integrated PROFIBUS DP interface and integrated inputs/outputs. The following PROFIBUS protocol profile s are available for the CPU 314C-2DP: - DP interface as master according to EN 50170. - DP inter[...]
-
Page 7
A utomation and Drive s - SCE T I A Training Document Page 7 of 25 Module 2.1 OPERATING THE CPUS 31XC Operator control and display elements The following illustration shows the operator c ontrol and display elements of a CPU 31xC. The arrangement and number of elements in so me CPUs differ from this illustration. The figures show the following CPU [...]
-
Page 8
A utomation and Drive s - SCE T I A Training Document Page 8 of 25 Module Status and fault/error displays The CPU has the following LED displays: Slot for the SIMATIC Micro Memory Card (MMC) A SIMATIC Micro Memory Card (MMC) is used as a memory module for the CPU 31xC. The MMC can be used as a load memory and as a transportable data carrier. The MM[...]
-
Page 9
A utomation and Drive s - SCE T I A Training Document Page 9 of 25 Module 2.2 MEMORY AREAS OF THE CPU 31XC Foreword Notes H H a a r r d d w w a a r r e e c c o o n n f f i i g g u u r r a a t t i i o o n n STEP 7 program Testing Introduction The memory of the CPU 31xC can be divided into three areas: Note Only with the MMC plugged in is it possible[...]
-
Page 10
A utomation and Drive s - SCE T I A Training Document Page 10 of 25 Module Retentivity Your CPU 31xC has retentive me mory. Retentivity is implement ed on the MMC and on the CPU. Due to this retentivity, the cont ents of the retentive memory are retained even after the mains supply has been switched off and the CPU has been restarted (warm restart)[...]
-
Page 11
A utomation and Drive s - SCE T I A Training Document Page 11 of 25 Module 3. CREATING THE HARDWARE CONFIGURATION FOR THE CPU 314C-2DP In Step 7, files are managed with the 'SIMATIC Manager'. Here, program blocks can be copied, for example, or called for further processing with other tools by clicking on them with the mouse. Use of the SI[...]
-
Page 12
A utomation and Drive s - SCE T I A Training Document Page 12 of 25 Module The hardware configuration of the PLC is mapped in the 'SIMATIC 300 Station' and 'CPU' folders. This is done in the special case where a c onfiguration is created with the CPU 314C-2DP. Also, a clock memory is configured and the addresses of the input and[...]
-
Page 13
A utomation and Drive s - SCE T I A Training Document Page 13 of 25 Module 3. The project is now assigned the name 'CPU314C_2DP' under 'Name' ( → CPU314C_2DP → OK) 4. A 'SIMATIC 300-Station' station is now inserted. ( → Insert → Station → SIMATIC 300 Station) Foreword Notes Hardware configuration STEP 7 progr[...]
-
Page 14
A utomation and Drive s - SCE T I A Training Document Page 14 of 25 Module 5. Open the configurati on tool by double-clicking on 'Hardw are' . ( → Hardware) 6. Open the hardware catalog by clicking on the symbol. ( → ) The catalog is divided into the following directories: - PROFIBUS-DP/PA, SIMATIC 300, SIMATI C 400 and SIMATIC PC Bas[...]
-
Page 15
A utomation and Drive s - SCE T I A Training Document Page 15 of 25 Module 7. Insert a rail by double-clicking on 'Rail' ( → SIMATIC 300 → RACK-300 → Rail). A configuration table for desi gning Rack 0 is then displayed. Foreword Notes Hardware configuration STEP 7 program Testing A5 Issue date: 02/2008 Programming the CPU 314C-2DP[...]
-
Page 16
A utomation and Drive s - SCE T I A Training Document Page 16 of 25 Module 8. From the hardware catalog, you now can sele ct any of the modules that are also plugged into the real rack and insert them in the configuration table. To do this, you must click on the name of the respective module, hold down the mouse button and drag the module into a ro[...]
-
Page 17
A utomation and Drive s - SCE T I A Training Document Page 17 of 25 Module 9. In the next step, we drag the CPU 314C-2DP ont o the second slot. When this is being done, the order number and the version of the CPU can be read on the front of the CPU. ( → SIMATIC 300 → CPU-300 → CPU 314C-2DP → 6ES7 314-6CF00-0AB0). 10. In the following dialog[...]
-
Page 18
A utomation and Drive s - SCE T I A Training Document Page 18 of 25 Module 11. The properties of some modules can be altered ( → Click on module → Change properties → OK). For example, a clock memory c an be specified for all CPUs ( → Cycle/Clock memory → ∨ Clock memory → Memory Byte 100). Foreword Notes Hardware configuration STEP 7 [...]
-
Page 19
A utomation and Drive s - SCE T I A Training Document Page 19 of 25 Module 12. With most S7-300 CPUs, the addresse s of the I/O modules can be altered. This is done by double-clicking on the correspondi ng modules and altering their settings in the 'Addresses' tab. A note should always be made of these addr esses (addresses assigned autom[...]
-
Page 20
A utomation and Drive s - SCE T I A Training Document Page 20 of 25 Module 13. By clicking on the and buttons, the configuration table is now first stored and converted, and then loaded into the PLC. When th is is being done, the key switch on the CPU should be in the Stop position! ( → → ) Foreword Notes Hardware configuration STEP 7 program T[...]
-
Page 21
A utomation and Drive s - SCE T I A Training Document Page 21 of 25 Module 4. WRITING A STEP 7 PROGRAM We are writing the program to be tested in the st atement list language (STL), and it only contains two lines. Here, the frequencies of the MB100 clock memory byte activated in the hardware are to be read out on an output byte. Assignment list: MB[...]
-
Page 22
A utomation and Drive s - SCE T I A Training Document Page 22 of 25 Module 15. In the SIMATIC Manager, double-click on the 'OB1' block to open it ( → OB1) 16. As an option, you can enter the properties of the OB1 for documentation purposes and accept them with 'OK' . ( → OK) Foreword Notes Hardware configuration STEP 7 progr[...]
-
Page 23
A utomation and Drive s - SCE T I A Training Document Page 23 of 25 Module 17. 'LAD/STL/FDB Program S7 Blocks’ is an editor which allows you to create your STEP 7 program as you require. To this end, the OB 1 organization block with the first network has already been opened. In order to create your firs t logic operations, you must mark the [...]
-
Page 24
A utomation and Drive s - SCE T I A Training Document Page 24 of 25 Module 5. TESTING THE STEP 7 PROGRAM The STEP 7 program to be tested can now be loaded into the PLC. In our case, this is only OB1. 18. Save the organization block with and load it into the PLC by clicking on . When this is being done, the key switch on the CPU should be in the STO[...]
-
Page 25
A utomation and Drive s - SCE T I A Training Document Page 25 of 25 Module 19. To start the program, move the key switch to the RUN position. Click on the symbol to view the program in 'OB1' . ( → ) Foreword Notes Hardware configuration STEP 7 program Testing A5 Issue date: 02/2008 Programming the CPU 314C-2DP[...]