Smeg PTSA726X5 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16

Go to page of

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Smeg PTSA726X5, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Smeg PTSA726X5 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Smeg PTSA726X5. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Smeg PTSA726X5 should contain:
- informations concerning technical data of Smeg PTSA726X5
- name of the manufacturer and a year of construction of the Smeg PTSA726X5 item
- rules of operation, control and maintenance of the Smeg PTSA726X5 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Smeg PTSA726X5 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Smeg PTSA726X5, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Smeg service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Smeg PTSA726X5.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Smeg PTSA726X5 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    Table of contents 3 1. Precautions for safety and use _________________________ 4 2. Fitting the appliance in the top _________________________ 5 2.1 Fixing to the supporting structure ________________________________________5 3. Electrical connection ________________________________ 7 3.1 Clearance above and around dom estic appliances ___________[...]

  • Page 2

    Precautions for Safety and Use 4 1. Precautions f or safety and use THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE. TAKE GOOD CARE OF IT AND KEEP IT TO HAND THROUGHOUT THE HOB'S LIFE CY CLE. USERS ARE ADVISED TO READ THIS MANUAL AND ALL THE INSTRUCTIONS IT C ONTAINS BEFORE USING THE HOB. ALSO KEEP THE SET OF NOZZLES PROVIDED IN A SAFE PLACE.[...]

  • Page 3

    Instructions for the Installer 5 2. Fitting the appliance in the top The procedures required below must be carried o ut by a skilled builder and/or joiner. The hob can be installed on vari ous materials, including masonry, metal, solid wood and wood finished with plastic laminates, pr ovided the material is heat-resistant (T 90° C). 2.1 Fixing to [...]

  • Page 4

    Instructions for the Installer 6 edge of the gasket B . The dimensions in the drawing belo w refer to the hole on the inside edge of the gasket. In case of installation on a hollow compartment with doors, a separating panel has to be placed under the hob. K eep a mini mum distance of 10 mm between the bottom of the unit and the panel surface. The p[...]

  • Page 5

    Instructions for the Installer 7 3. Electrical connection Check that the power su pply line voltage and size are as speci fied on the nameplate underneath the applian ce's casing. This nameplate must never be removed. The plug on the end of the power supply lead and the wall socket must be of the same type and comply with the relevant re gulat[...]

  • Page 6

    Instructions for the Installer 8 3.1 Clearance abo ve and around domestic appliances Extract from AS5601 REQUIREMENTS 1 Overhead clearances – (M easurement A ) Range hoods and exhaust fans shall be installed in accordance with the manufacturer’s instruction s. However, in no case shall the cleara nce between the highest part of the hob of the c[...]

  • Page 7

    Instructions for the Installer 9 2 Side clearances – (Mea surements B & C) Where B , measured from the peri phery of the nearest burner to any vertical combustible surface , is less than 200 mm , the surface sh all be protected in accordance with Clause 5.12.1.2 to a height C of not less than 150 mm above the hob for the full dimension (width[...]

  • Page 8

    Instructions for the Installer 10 4. GAS CONNECTION This appliance is suitable for installation with Natural Ga s or LPG (propane). Refer to page 12 for the relevant burner pressure and appropriate injector si zes. When the appliance is to be connected to Natural Gas then the pressure regulato r supplied must be fitted to the gas inlet. A test poin[...]

  • Page 9

    Instructions for the Installer 11 5. Adapting to diff erent types of gas Before carrying out the operations described below, disconnect th e appliance from the electricity supply. The hob of the cooker is adjusted for use with either natur al gas at a pressure of 1.0 kPa . If used with other types of gas, you have to replace the nozzles, the n adju[...]

  • Page 10

    Instructions for the Installer 12 5.2 Adjusting fo r bottled gas Undo the scre w A and push the support B fully down. Remove the nozzle C with a spanner and fit the suitable one followi ng the instructions in the tables referring to the type of gas to be used. The nozzle must not be tightened with a torque of more than 3 Nm . Return the support B t[...]

  • Page 11

    Instructions for the Installer 13 5.4 Adjusting the primary air flow Refers to the gap “ X ” in mm. BURNER NG – 1.0 kPa ULPG – 2.75kPa Auxiliary 4.0 10.0 Semi rapid 4.0 10.0 Rapid (3) 4.0 10.0 Rapid (6) 4.0 10.0 Rapid (7) 4.0 10.0 Internal 5.0 8.0 WOK double flame (4-8) External 10.0 13.0 WOK 5.0 12.0 5.5 Reassembling the hob skin Reverse t[...]

  • Page 12

    Instructions for the Installer 14 5.8 Hob b urner lay out Burner type 1 Auxiliary 2 Semi rapid 3 Rapid 4 WOK Double flame 5 WOK 6 Rapid 7 Rapid 8 WOK Double flame 5.9 Greasing the gas taps Over time, the gas taps may beco me stiff or jam. Clean their insides and change their lubricating grease. This operation must be carried out by a skilled techni[...]

  • Page 13

    Instructions for the User 15 6. Description of contr ols 6.1 The fr ont panel All the hob's control and monitori ng devices are placed together on the front panel. MODEL 60 CONTROL PANEL 4 Burner Hob MODEL 70 CONTROL PANEL 5 Burner Hob 6 Burner Hob, UR2 at Side 6 Burner Ho b, central UR2 KNOB OPERATING MODE To light the flame, press the knob a[...]

  • Page 14

    Instructions for the User 16 7. Using the hob Check that the fixing rings, burners, flame diffuser rings and pan stands are fitted correctly. The burner pins A must be fitted into the recesses B in the flame diffuser ring. The holes C in the flame diffuser ring must mate with the ignition plugs and thermocouples D on the hob. 7.1 Lighting b urners [...]

  • Page 15

    Instructions for the User 17 7.4 P an diameters BURNERS 1. Auxiliary 2. Semi rapid 3. Rapid 4. WOK double flame 5. WOK 6. Rapid 7. Rapid 8. WOK double flame min. and max. Ø (in cm) 7-18 10-24 18-24 20-28 20-28 18-24 18-24 20-28[...]

  • Page 16

    Instructions for the User 18 8. Cleaning and maintenance Before carrying out any operations, disconnect the ap pliance from the electricity supply. 8.1 Cleaning stainless steel To keep the hob in good condition, it must be cleaned regula rly, after each u se, first allowing it to cool. 8.1.1 Routine daily hob cleaning When cleaning an d caring for [...]