English dropdown-ico

Snapper FB13250BS, GM2515KAW, GM2513H manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Snapper FB13250BS, GM2515KAW, GM2513H, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Snapper FB13250BS, GM2515KAW, GM2513H one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Snapper FB13250BS, GM2515KAW, GM2513H. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Snapper FB13250BS, GM2515KAW, GM2513H should contain:
- informations concerning technical data of Snapper FB13250BS, GM2515KAW, GM2513H
- name of the manufacturer and a year of construction of the Snapper FB13250BS, GM2515KAW, GM2513H item
- rules of operation, control and maintenance of the Snapper FB13250BS, GM2515KAW, GM2513H item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Snapper FB13250BS, GM2515KAW, GM2513H alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Snapper FB13250BS, GM2515KAW, GM2513H, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Snapper service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Snapper FB13250BS, GM2515KAW, GM2513H.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Snapper FB13250BS, GM2515KAW, GM2513H item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    OPERA T OR’S MANU AL Mfg. No. Model No. Description 7085922 FB13250BS 13 hp Briggs, Hydro-Drive 7085923 GM2515KA W 15 hp Kaw asaki, Hydro-Dr iv e 7085924 GM2513H 13 hp Honda, Hydro-Drive Field and Brush Mo wer Manual No. 7078128 (I.R. 10/1/04)[...]

  • Page 2

    1 T roub leshooting, Adjustment and Service .....14 Chart .....................................................................14 Travel Control Adjustment ....................................16 Blade Clutch Adjustment .......................................17 Blade Brake Adjustment .......................................18 Mower Belt Adjustment ..[...]

  • Page 3

    2 SAFE OPERA TION PRA CTICES FOR W ALK-BEHIND MO WERS This cutting machine is capable of amputating hands and feet and throwing objects. Failure to observe the follow- ing safety instructions could result in serious injury or death. GENERAL OPERA TION • Read, understand, and follow all instructions on the machine and in the manual(s). Be thorough[...]

  • Page 4

    3 Safety Rules and Information SLOPE OPERA TION Slopes are a major factor related to slip and fall acci- dents, which can result in severe injury. All slopes require extra caution. If you feel uneasy on a slope, do not mow it. Do • Mow across the face of slopes; never up and down. Exercise extreme caution when changing direction on slopes. • Re[...]

  • Page 5

    4 Safety Rules & Information SER VICE AND MAINTENANCE • Use extra care in handling gasoline and other fuels. They are flammable and vapors are explosive. a) Use only an approved container. b) Never remove gas cap or add fuel with the engine running. Allow engine to cool before refu- eling. Do not smoke. c) Never refuel the unit indoors. • I[...]

  • Page 6

    5 Safety and Instructional Decals Decal - Warning (7028490) Important Safety Operating Instructions. Read and understand before operating machine Decal - Engine Throttle Control (7029167) Models - All mowers Decal - Blade Control, Engine Key Switch (7028349) Models - All mowers Decal - Traction Drive / Freewheel Lever (1725229) Models - All mowers [...]

  • Page 7

    6 Features & Controls Engine On/Starter Rotate this key switch to the ON position before pulling on the starter rope. If the mower is equipped with the optional electric start- ing system, rotate the key past the ON position to engage the starter. When the engine starts, release the key. Throttle Contr ol The throttle controls engine speed. Mov[...]

  • Page 8

    7 Operating the Mower Engage Disengage Figure 4 - Traction Drive / Freewheel Control ST AR TING THE ENGINE NOTE - The procedures outlined within this section are general guidelines, and are in no way meant to replace or supercede engine manufacturer's operating instruc- tions. In order to obtain optimum performance from your engine, refer to y[...]

  • Page 9

    8 Operating the Mower T o Pr opel Unit Forwar d: • Grasping both upper handle/safety bar (A, Figure 5) and lower portion of traction drive engagement bar (B) with both hands, slowly begin squeezing engage- ment bar up toward handle. The unit should begin moving forward. T o Pr opel Unit In Rever se: • Grasping both upper handle/safety bar (A, F[...]

  • Page 10

    9 Operating the Mower OFF RUN ST ART A Figure 7 - PTO Engaged A. Blade Engagement Lever in engaged position. OFF RUN ST ART A Figure 8 - PTO Disengaged A. Blade Engagement Lever in the disengaged posi- tion. ENGA GING/DISENGA GING THE CUTTING BLADE To Engage Cutting Blade: • Push Blade Engagement Lever forward and then to the right until lever lo[...]

  • Page 11

    10 Operating the Mower A D C C B Figure 9 - Adjusting Height A. Skid B. Capscrew C. Washer D. Nut T O ADJUST CUTTING HEIGHT The front skids on the brush cutter have 3 sets of holes (Figure 9) for height adjustment: – Top holes - 3 1 / 4 " cutting depth – Center holes - 4" cutting depth – Bottom holes - 4 3 / 4 " cutting depth ?[...]

  • Page 12

    11 Regular Maintenance LUBRICA TION Service Interval: Every 25 Hours Lubricate the unit at the locations shown in Figure 10 as well as the lubrication points listed. Generally, all moving parts should be oiled where contact is made with other parts. Keep oil and grease off belts and pulleys. Wipe surfaces clean before and after lubrication. Grease:[...]

  • Page 13

    12 Regular Maintenance TIRE PRESSURE Tire pressure is 20 psi (1.4 bar). B A TTER Y SER VICE Cleaning the Battery and Cables - 9HP Models Service Interval: Every 100 Hours 1. Disconnect the cables from the battery, negative cable first (C, Figure 13a). 2. Remove the battery hold-down (B), rubber protective sheet (D) and battery (A). 3. Clean the bat[...]

  • Page 14

    13 Regular Maintenance SER VICING THE MO WER BLADES Service Interval: Every 100 Hours or As Required 1. Raise the front end of the brush mower and securely support in the raised position. 2. Blades should be sharp and free of nicks and dents. If worn or damaged, replace the blades as described in following steps. 3. To remove the blade, use a wood [...]

  • Page 15

    14 T roubleshooting, Adjustment, & Service TR OUBLESHOO TING PROBLEM CAUSE REMEDY Engine will not turnover or start. 1. PTO lever in the engaged position. Place in disengaged position. 2. Out of fuel. If the engine is hot, allow it to cool, then refill the fuel tank. 3. Engine flooded. Disengage choke. 4. Battery terminals require cleaning. See[...]

  • Page 16

    15 T roubleshooting, Adjustment & Service T r oubleshooting Cont. Blade will not engage. 1. Blade clutch rod too loose. See Blade Clutch Adjustment Section. 2. Blade belt worn or broken. Turn off engine and inspect belt. Adjust or replace as required. 3. Over-stretched or broken spring Turn off engine and inspect spring. Replace on blade clutch[...]

  • Page 17

    16 T roubleshooting, Adjustment, & Service TRA VEL CONTROL ADJUSTMENT Serial Number 0-011903999 1. The Travel Control engagement bars (A, Figure 16a) should be an equal distance from the Upper Handle Bar. If they are not, adjust their position. 2. Loosen the wing nut locknut (D) and rotate control rod (C) until engagement bars are properly adju[...]

  • Page 18

    17 T roubleshooting, Adjustment, & Service A D C B E Figure 17 - Blade Clutch Adjustment A. Clutch Rod B. Clutch Rod Lever C. Clutch Rod Fitting D. Locknut E. Hairpin Clip BLADE CLUTCH ADJUSTMENT If the mower blade does not stop running when the blade clutch lever is in the DISENGAGED position, does not run at full speed, adjust the Blade Clutc[...]

  • Page 19

    18 T roubleshooting, Adjustment, & Service BLADE BRAKE ADJUSTMENT The mower blade should stop within 5 seconds after the Blade Engagement Lever is moved to the DISEN- GAGED position. This adjustment is checked by: 1. Remove blade clutch cover plate (A, Figure 19). 2. Start engine. 3. With mower blade engagement lever in the DISEN- GAGED positio[...]

  • Page 20

    19 T roubleshooting, Adjustment, & Service A D B 1/8” Max. C Figure 21 - Traction Drive Belt Adjustment A. Transmission Pulley B. Drive Belt C. Engine Pulley D. Idler Pulley Figure 22 - Traction Drive Belt Adjustment A. Adjustment Nut TRA CTION DRIVE BEL T ADJUSTMENT If the mower drive is not functioning properly, the drive belt may need to b[...]

  • Page 21

    20 T roubleshooting, Adjustment & Service E D G F B C A Figure 24 - Belt Alignment A. Blade Drive Pulley B. Mower Belt C. Mower Tension Idler D. Transmission Pulley E. Transmission Belt F. Engine Pulley G. Transmission Tension Idler MO WER BEL T REPLA CEMENT To replace the mower blade drive belt; NOTE - The traction drive belt will have to be r[...]

  • Page 22

    21 Specifications Parts & Accessories ENGINEl BRIGGS HONDA KAWASAKI BRIGGS Engine 13 HP B&S 13 HP Honda 15 HP V-twin 16 HP B&S Transmission Hydro/Variable Hydro/Variable Hydro/Variable Hydro/Variable Ground Speed (mph) Infinite (.01 - 6) Infinite (.01 - 6) Infinite (.01 - 6) Infinite (.01 - 6) Weight (lbs) 287 298 299 N/A Overall Length[...]

  • Page 23

    22 Notes[...]

  • Page 24

    A Division of Simplicity Manufacturing, Inc. 535 Macon Street/PO Box 777 McDonough, GA 30253 © Copyright 2004 All Rights Reserved. Printed in USA.[...]