English dropdown-ico

Southbend SB1269 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Southbend SB1269, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Southbend SB1269 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Southbend SB1269. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Southbend SB1269 should contain:
- informations concerning technical data of Southbend SB1269
- name of the manufacturer and a year of construction of the Southbend SB1269 item
- rules of operation, control and maintenance of the Southbend SB1269 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Southbend SB1269 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Southbend SB1269, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Southbend service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Southbend SB1269.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Southbend SB1269 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    M O D E L S B126 9 T AP E R A T T A C H M E NT Instruction Sheet This taper attach ment is heav y! Get assistance when installing this accessor y o n the lathe . Wear heavy duty leat her b oots for foot and t oe pr o tec tion , and keep hands and finger s away fr om all pinc h poi nts. Ignor ing this warning can lead to a sev er e cr ushing injur y[...]

  • Page 2

    Identification Serio us pe rsonal injur y coul d occu r if you connec t the lathe to power before complet ing the installat ion p rocess. DO NOT connec t power u ntil instruc ted to do so l at e r in this manual. Untr ained users hav e an increased risk of serious ly injuri ng t hemselves wi th t his l athe accessor y . Do not op erate l athe unti[...]

  • Page 3

    Inventor y W he n you are com pl etel y satisfied with the condi tion o f your ship men t, yo u should in ven tory the con tents . Inventor y (Fi gure 3) Q ty A. Cap Screws M10-1.5 x 40mm ( Taper Attachment Mounting) ...................... 4 B. Taper Attachment Assembly ......................... 1 C. Tapered Pins 8.7 x 7.7 x 47mm ..................[...]

  • Page 4

    The unpainted surfaces are coated with a heavy- duty rust preventative that prevents corrosion during shipment and storage. This rust preventative has been a close ally and guardian since this item left the factory. If the unpainted surfaces are free of rust, then be thankful that the rust preventative did its job...and try to stay thankful as you [...]

  • Page 5

    Inst allation T o inst all the taper att ac hment: 1 . DISCONNECT LATHE FROM POWER! 2 . With the assistance of a helper and using a 6mm hex wrench, remove the four cap screws holding the splash guard on the rear of the lathe. 3 . Using a 5mm hex wrench, remove the two leadscrew end-cap cap screws shown in Figure 4 . Note : Make sure to keep the cor[...]

  • Page 6

    9 . Lift out the slide block without losing the copper anti-score plug ( Figure 8 ). 12 . Clean the bearings and races with mineral spirits, then dry and repack them with white lithium grease. 13 . Install the bearings and races onto the leadscrew in the order shown in Figure 10 . Figure 8. Slide block copper anti-score plug. 10 . Apply a dab of mu[...]

  • Page 7

    Figure 15. T op plate installation. 22 . Reinstall the top plate as shown in Figure 15 . 17 . Make sure the copper plug is still inside of the slide block. 18 . With the help of an assistant, raise the taper attachment underneath the slide block, so the pivot pin slides into the pin bore in the slide block (see Figure 12 ). 19 . With your assistant[...]

  • Page 8

    Figure 16. Deadman and arm installation. Deadman Clamp Cap Screw Deadman Arm Arm Clevis Arm Clamp Cap Screw 29 . Rotate, push in, or pull out the adjustment cam to adjust the deadman arm so it is as parallel as possible with the lathe bed in both the vertical and horizontal plane. Note : You may have to rotate the deadman arm so the arm clevis allo[...]

  • Page 9

    35 . Loosen the four mounting cap screws and rotate the taper attachment left or right to correct the alignment (see Figure 21 ). Figure 22. Roll pin installation. Pre- Drilled 6.5mm Pilot Holes for T apered Pins 36 . Retighten the taper attachment cap screws, and double check your parallelism. 37 . Using the existing pilot holes in the taper attac[...]

  • Page 10

    Operation 6 . Retighten both dovetail lock cap screws. 7 . Begin lathe operations. W he n the deadman cla m p cap screw s a re l oose, the d ead man clamp s l i des alo ng t h e lathe w a y , and the tape r attachmen t is disengaged. No r mal la t h e tu rni ng o perati ons ca n be con du ct ed. W he n the deadman cla m p cap screw s a re tighten e[...]

  • Page 11

    T o disable the t aper attachment: 1 . DISCONNECT LATHE FROM POWER! 2 . Use an 8mm hex wrench, and loosen both deadman clamp cap screws shown in Figure 26 , so the deadman can slide on the way as the carriage is moved. Figure 27 . T aper angle control knob. Dovetail Lock Cap Screw T aper Angle Control Knob 3 . Using a 6mm hex wrench, loosen both do[...]

  • Page 12

    3. U sing a n oil can w i th the same oil yo u use on yo ur lathe ball oile rs, ap pl y oil on the k n ob threads shown in Figure 30 . T o clean the t aper attachment: 1 . DISCONNECT LATHE FROM POWER! 2. V acuum excess meta l c hi ps a n d w i pe off the remain ing me ta l, coo la n t, a n d oils w i th a dr y cl oth. If any coolant sludge has buil[...]

  • Page 13

    2 9 8 7 3 33 32 31 30 28 12 13 5 2 21 20 18 17 16 15 14 12 13 12 11 10 34 35 27 26 36 25 22 24 36 23 19 20 51 10 11 48 46 47 33 45 44 43 40 42 40 39 38 37 23 41 46 49 50 T aper Att ac hment Breakdown F or Produ ct Mfg. Since 1 /1 0 Mod el S B 12 69 -1 3 - PARTS[...]

  • Page 14

    REF PART # DE SCRI PTIO N REF PART # DE SCRI PTIO N 2 PCAP02M CAP SCREW M6-1 X 20 28 PSB1269028 PIN 3 PSB1269003 BALL OILER 30 PSB1269030 PIVOT SADDLE 5 PSB1269005 END CAP 31 PSB1269031 GIB 7 PFH04M FLAT HD SCR M6-1 X 8 32 PSB1269032 GIB SCREW 8 PSB1269008 COVER PLATE 33 PCAP31M CAP SCREW M8-1.25 X 25 9 PSB1269009 SLIDE BLOCK 34 PSB1269034 DOVETAIL[...]

  • Page 15

    W AR RANT Y & RETU R NS This quality product is warranted by South Bend Lathe Company to the original buyer for one year from the date of purchase. This warranty does not apply to consumable parts, or defects due to any kind of misuse, abuse, negligence, accidents, repairs, alterations or lack of maintenance. We do not reimburse for third party[...]

  • Page 16

    Copyright © F ebr uary , 2010 By South Bend Lathe Co . R evised April, 2010 (CR ). WARNING: No portion of this manual ma y be repr oduced in any sha pe or form without the written appr ov al of South Bend La the Co . #CR12550 Printed in T aiwan. www .southbendlathe.com[...]