English dropdown-ico

Stanley Black & Decker CS05 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Stanley Black & Decker CS05, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Stanley Black & Decker CS05 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Stanley Black & Decker CS05. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Stanley Black & Decker CS05 should contain:
- informations concerning technical data of Stanley Black & Decker CS05
- name of the manufacturer and a year of construction of the Stanley Black & Decker CS05 item
- rules of operation, control and maintenance of the Stanley Black & Decker CS05 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Stanley Black & Decker CS05 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Stanley Black & Decker CS05, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Stanley Black & Decker service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Stanley Black & Decker CS05.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Stanley Black & Decker CS05 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    © 2014 Stanley Black & Decker , Inc. New Britain, CT 06053 U.S.A. 66864 7/2014 V er . 8 USER MANUAL Safety , Operation and Maintenance CS05/CS06 HYDRAULIC CHAIN SA W[...]

  • Page 2

    [...]

  • Page 3

    CS05/CS06 User Manual ◄ 3 WARNING SERIOUS INJUR Y OR DEA TH COULD RESUL T FROM THE IMPROPER REP AIR OR SERVICE OF THIS T OOL. REP AIRS AND / OR SERVICE T O THIS TOOL MUST ONL Y BE DONE BY AN AUTHORIZED AND CERTIFIED DEALER. SERVICING: This manual contains safety , operation, and routine maintenance instructions. Stanley Hy- draulic T ools recomme[...]

  • Page 4

    4 ► CS05/CS06 User Manual Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULA TIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte - nance personnel. Safety symbols and signal words, as shown below , are used to [...]

  • Page 5

    CS05/CS06 User Manual ◄ 5 T ool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose. These safety precautions are given for your safety . Re - view them carefully before operating the tool and before performing general maintenance or rep[...]

  • Page 6

    6 ► CS05/CS06 User Manual – maintenance instructions for the saw chain. – Only use replacement bars and chains specied by Stanley Hydraulic T ools. Chains must meet the requirements of ANSI B175.1 for low kick - back performance. • Always be well rested and mentally alert before op - erating the chain saw . • Do not allow other persons[...]

  • Page 7

    CS05/CS06 User Manual ◄ 7 The following guidelines must be followed to prevent accidental contact with overhead electrical conductors and/or communication wires and cables. (ref. ANSI Z133.1-2000) Working in Proximity to Electrical Hazards: An inspection shall be made by a qualied arborist to determine whether an electrical hazard exists befor[...]

  • Page 8

    8 ► CS05/CS06 User Manual T able 2 – Minimum approach distances to energized conductors for persons other than qualied line-clearance arborists and qualied line-clearance ar - borist trainees. Nominal V oltage kV phase-to-phase 1 Distance ft-in m 0.0 to 1.0 10–00 3.05 1.1 to 15.0 10–00 3.05 15.1 to 36.0 10–00 3.05 36.1 to 50.0 10–[...]

  • Page 9

    CS05/CS06 User Manual ◄ 9 28323 CE Decal (CE Models Only) 28409 Composite Decal (CE Models Only) D 30 LPM @ 138 BA R EHTMA CA TEGORY 1 1207 Circuit T ype D Decal (CE Models Only) Fa ilure to use hydraulic hose labeled and certified as non-conductive when using hydraulic tool so n or near electric lines ma yr esul ti n deat ho r Fo rp roper and sa[...]

  • Page 10

    10 ► CS05/CS06 User Manual The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy - draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic T ools. They are: Certied non-conductive — constructed of thermop[...]

  • Page 11

    CS05/CS06 User Manual ◄ 1 1 Oil Flow Hose Lengths Inside Diameter USE ( Press/Return) Min. Working Pressure GPM LPM FEET METERS INCH MM PSI BAR Certied Non-Conductive Hose - Fiber Braid - for Utility Bucket T rucks 4-9 15-34 up to 10 up to 3 3/8 10 Both 2250 155 Conductive Hose - Wire Braid or Fiber Braid -DO NOT USE NEAR ELECTRICAL CONDUCT OR[...]

  • Page 12

    12 ► CS05/CS06 User Manual Flow Range Nominal Operating Pressure (at the power supply outlet) System relief valve setting (at the power supply outlet) Maximum back pressure (at tool end of the return hose) Measured at a max. uid viscosity of: (at min. operating temperature) T emperature: Sufcient heat rejection capacity to limit max. uid[...]

  • Page 13

    CS05/CS06 User Manual ◄ 13 OPERA TING PROCEDURES The following are general wood cut ting procedures and techniques. Dif ferences in the terrain, vegetation, and type of wood will make this infor mation more or less val - id for particu lar areas. For advice on specic woodcut - ting problems or techniques for your area, consult your local Stanl[...]

  • Page 14

    14 ► CS05/CS06 User Manual FELLING OR BACK CUT 4. The felling or back cut is made on the side opposite and at least 2 inches above the hori zontal undercut (the felling cut is made higher as the size of the tree increases). Place the saw so the hand guard is close to the tree trunk and the bucking cleat is dug in. 5. Start the cut horizontally . [...]

  • Page 15

    CS05/CS06 User Manual ◄ 15 Figure 4. Crosscutting Logs Larger than Bar Length With Pressure on T op LOGS WITH PRESSURE ON TOP (FIGURE 3) 1. Observe all safety precautions. 2. Begin with an upper cut, down from the top. Do not cut too deeply . A cut of about 1/3 of the log diameter is enough. 3. Finish with a bottom cut. They should meet. Figure 3[...]

  • Page 16

    16 ► CS05/CS06 User Manual Figure 6. Crosscutting Thick Logs with Pressure on Bottom LOGS/LIMBS WITH PRESSURE ON BOTTOM (FIGURE 5) 1. Observe all safety precautions. 2. Begin with a bottom cut. The depth of the cut should be about 1/3 of the log diameter . 3. Finish with an upper cut, down from the top. The saw cuts should meet. Figure 5. Crosscu[...]

  • Page 17

    CS05/CS06 User Manual ◄ 17 PRUNING AND DEBRANCHING 1. Observe all safety precautions. 2. Use both hands. Keep a rm grip. 3. Be alert for kickback. Do not allow the tip of the bar to touch anything while the chain is in motion. 4. Do not cut overhead. Keep the saw below chest lev - el. The chain is too close to your face in this position. COLD [...]

  • Page 18

    18 ► CS05/CS06 User Manual • Make sure all couplers are wiped clean before con - nection. • The hydraulic circuit control valve must be in the “OFF” position when coupling or uncoupling hydrau - lic tools. Failure to do so may result in damage to the quick couplers and cause overheating of the hy - draulic system. • Always store the too[...]

  • Page 19

    CS05/CS06 User Manual ◄ 19 If symptoms of poor performance develop, the following chart can be used as a guide to correct the problem. When diagnosing faults in operation of the saw , always make sure the hydraulic power source is supplying the correct hydraulic ow and pressure to the saw as listed in the table. Use a owmeter known to be ac[...]

  • Page 20

    20 ► CS05/CS06 User Manual Capacity CS05 ..................................................................................................... 12 and 15 inch/30 and 38 cm Cut Lengths CS06 ......................................................................................... 12, 15 and 20 inch/30, 38 and 51 cm Cut Lengths Weight (w/o bar) .....[...]

  • Page 21

    CS05/CS06 User Manual ◄ 21 CS05/CS06 P ARTS ILLUSTRA TION[...]

  • Page 22

    22 ► CS05/CS06 User Manual ITEM NO. P ART NO. QTY DESCRIPTION 1 00753 09622 8 CAPSCREW CAPSCREW U/W MODEL 2 07636 08202 1 NAME T AG—CS06 NAME T AG—CS05 3 28323 1 CE DECAL (CE ONL Y) 4 07652 1 REAR GEAR HSG ASSY (7–9 GPM) 07834 1 REAR GEAR HSG ASSY (4–6 GPM) 5 00289 2 DOWEL PIN 6 04041 4 BUSHING 7 00020 1 O-RING 8 07612 1 IDLER SHAFT 9 041[...]

  • Page 23

    CS05/CS06 User Manual ◄ 23 ITEM NO. P ART NO. QTY DESCRIPTION 71 07610 1 SPRING 72 00190 1 ROLL PIN 73 10537 1 KEEPER 74 07625 1 PLUG BUTTON 75 03786 1 GPM STICKER (7–9 GPM) 03782 1 GPM STICKER (4–6 GPM) 76 05144 1 BAR & CHAIN GUARD 77 00767 1 GREASE FITTING U/W MODEL ONL Y 00936 2 ADAPTER (NOT SHOWN) 26414 1 LOCK OUT KIT , SHIPPED INST A[...]

  • Page 24

    24 ► CS05/06 User Manual For underwater hydraulic tools the applications are broken down into four quadrants depending on type of tool and method of operation. The types of tools are percussive and rotational, each with different characteristics allowing for dif - ferent depth operation. With percussive tools, the nitrogen accumulator PSI must co[...]

  • Page 25

    CS05/06 User Manual ◄ 25 NOTES[...]

  • Page 26

    Stanley Hydraulic T ools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www .stanleyhydraulics.com[...]