Star Micronics NX-2410 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119

Go to page of

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Star Micronics NX-2410, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Star Micronics NX-2410 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Star Micronics NX-2410. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Star Micronics NX-2410 should contain:
- informations concerning technical data of Star Micronics NX-2410
- name of the manufacturer and a year of construction of the Star Micronics NX-2410 item
- rules of operation, control and maintenance of the Star Micronics NX-2410 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Star Micronics NX-2410 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Star Micronics NX-2410, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Star Micronics service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Star Micronics NX-2410.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Star Micronics NX-2410 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    MULTI-FONT USERS MANUAL NOT INTENDED FOR SALE[...]

  • Page 2

    Federal Communications Commission Radio Frequency Interference Statement ‘his equipment generates and uses radio frequency energy and if not installed and used properly. that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio and is no guarantee that interfemnce wilJ not occur in a particular instaUat[...]

  • Page 3

    HOW TO USE THIS MANUAL This manual is organized into five chapters and four appendixes. To learn how to make the best use of your printer you are urged to read all of chapters 1 through 5. The appendixes can be referred to as necessary. Chapter 1 explains how to get the printer unpacked and set up. Read this chapter before you do anything else. Cha[...]

  • Page 4

    FEATURES OF THE PRINTER This printer is a compact, convenient, monochrome printer with a full complement of features, making it an excellent partner for a personal computer. It supports the IBM/Epson printer commands and character sets, enabling it to print just about anything your computer can generate, both text and graphics. Some of its main fea[...]

  • Page 5

    Type styles are: Draft characters, Courier characters, Prestige characters, ORATOR CHARACTERS, Sdp~ w, sfm' italics for ALL 4t.y&4. Print pitches are: Pica pitch (10 CPI), Semi-condensed pitch (15 CPI), Condensed elite pitch (10 CPI), Normal proportional, Elite pitch (12 CPI), Condensed pica pitch (17 CPI), and condensed proportional. Doub[...]

  • Page 6

    TABLEOFCONTENTS Chapter 1 SETTING UP THE PRINTER Locating the printer Unpacking and inspection Check the carton contents Setting up Mount the platen knob Remove the top cover Install the ribbon cartridge Replace the top cover Install the optional IC card Connect the printer to the computer Connect the printer’s power cord Loading single sheets Mo[...]

  • Page 7

    Page feed Top of form Forward micro-feed Reverse micro-feed Clearing the buffer Chapter 3 USING THE PRINTER WITH COMMERCIAL SOFTWARE 29 Installing your software 29 Printer menu Printer command options Type styles Page width Initialization sequence Setting the DIP switches 31 Using your software 31 Page alignment Type style and pitch selection Other[...]

  • Page 8

    Appendix C DOWNLOAD CHARACTER GENERATOR Draft character LQ character Appendix D CHARACTER SETS Standard character set IBM character set #2 IBM character set #l Additional character set International character sets 89 97 INDEX COMMAND SUMMARY 105 108[...]

  • Page 9

    Chapter 7 SET7NVG UP THE PRINTER Subjects covered in Chapter 1 include - l Locating the printer l Unpacking and inspection (names of parts) 0 Setting up l Loading single sheets l Loading and parking fanfold forms l Test printing l Adjusting the printing gap l Setting the DIP switches LOCATING THE PRINTER Give some thought to the best place to put t[...]

  • Page 10

    Figure 1-I. Check to make sure you have all five items: 1) Printer, 2) Paper guide, 3) Platen knob, 4) Ribbon cartridge, and 5) User’s mantial. Make an external inspection of the printer. Note the locations of the following parts: Bail lever: opens and closes the paper bail which holds the paper against the platen. 2[...]

  • Page 11

    Power 1 - Entrv slot Rear ‘Over / Bail lever xv,Release Platen knob Connector 1 Figure I-2. The printer’s external parts Release lever: releases the platen. This lever must be down for printing on single sheets, and up for fanfold forms. Top cover: protects the print head and other parts. Rear cover: protects the sprocket feed mechanism. Entr[...]

  • Page 12

    trgure nemovmg me rop cgver install the ribbon cartridge The top side of the ribbon cartridge has a handle for turning the ribbon. Turn this handle in the direction of the arrow to tighten the ribbon. &we T-4. Installing the ribbon cartridge 4[...]

  • Page 13

    Next place the ribbon cartridge on the print head carriage, guiding the ribbon between the print head and the platen. Press down firmly on the cartridge until it snaps into place. Replace the top cover Hold the cover upright and engage the tabs at the back. Then swing the front edge down until the cover is closed. Leave the cover closed during norm[...]

  • Page 14

    Connect the printer to the computer Connect the printer end of the interface cable to the connector socket on the right side of the printer as shown in Figure 1-6. Make sure the computer is turned OFF, then connect the other end of the cable to your computer as described in the computer manual. terface cable Figure I-6. Connecting the interface cab[...]

  • Page 15

    I guide I Figure i-7. Mounting the paper guide for single sheets Semiautomatic loading Single sheets can be loaded manually with power off, or semiauto- matically with power on. We will start the easy way with semiautomatic loading. Check that the release lever is down and the bail lever back (bail closed), then switch power on. You will hear a sho[...]

  • Page 16

    lever I Figure l-8. Loading a single sheet Manual loading It is also possible to load paper manually while the printer’s power is off. The procedure is: 1. 2. 3. 4. 5. 6. Check that printer power is off and the release lever at the back of the printer is down. Insert a single sheet of paper into the entry slot as far as it will go, the same way a[...]

  • Page 17

    LOADING AND PARKING FANFOLD FORMS Fanfold forms have holes along the sides and perforations between the sheets. They are also called sprocket forms, punched forms, or just plain “computer paper”. This printer accepts forms up to 10” wide. Fanfold forms are loaded, parked, and unparked as explained next. 1. Place a stack of fanfold paper behin[...]

  • Page 18

    Clamp lever , ,YYrF ,-,“. vv’c,,r,ry L,lr irv,vrnrc bu.Tra Iv rnrose tne sprocltet teetn 10. Fit the holes in the paper over the sprocket pins. Check that the paper is even. 11. Close the sprocket covers (Figure l-l 1). 12. Raise one of the clamp levers to lock one sprocket unit in place. 10[...]

  • Page 19

    13. Turn the platen knob to feed the paper forward until it comes out from under the top cover. 14. Move the bail lever back to close the bail. 15. Check that the paper is feeding in flat, then raise the other clamp lever to lock the other sprocket unit. 16. Replace the rear cover. Hold it tilted upward and insert the two tabs at the bottom into th[...]

  • Page 20

    3. Tear off the printed form at the last perforation, leaving not more than about half a page showing above the top cover. If necessary, press the Paper Feed switch to feed paper forward until a perforation is located just above the top cover, and tear there. 4. Press the Quiet Mode switch on the control panel and hold it down. 5. Still holding the[...]

  • Page 21

    I Figure l-73. Short test pattern Long self test To see the printer’s variety of type styles, you can run the long version of the printer’s self test. 1. Check that paper is in position for printing. 2. With power off, press the Paper Feed switch on the control panel and hold it down. 3. Still holding the Paper Feed switch down, turn the printe[...]

  • Page 22

    ADJUSTING THE PRINTING GAP The distance between the print head and the platen can be adjusted to accommodate different paper thicknesses. To make this adjustment, open the top cover. The adjustment lever is located near the left end of the paper bail. Pulling the adjustment lever towards you widens the gap; pushing it away from you narrows the gap.[...]

  • Page 23

    Figure l-15. DIP switches Switch 1 Function 1 ON 1 OFF 1 l-l Page length 11 inches 12 inches l-2 Auto CR Yes No l-3 Bottom margin None 1 inch 1 1-4 1 Auto sheet feeder 1 Inactive 1 Active 1 l-5 Paper-out detector Enabled Disabled l-6 Printer mode Standard IBM Chamcter set (Std. Mode) Italics Graphics I ‘-’ I Character set (IBM Mode) I Set #2 I [...]

  • Page 24

    Switch l-l: Is the page length of your paper 11 inches or 12 inches? Leave this switch ON if you will be using 11-inch forms. Move it to the OFF position if you will be using 12-inch forms. Switch l-2: Do you want an automatic carriage return? Normally you should leave this switch ON. The printer will automatically perform a carriage return by movi[...]

  • Page 25

    If selected mode, you IBM set or ON character #2, is computers an interface most kind). selects set for with 7-bit Switch l-8: Do you want an automatic line feed? If you leave this switch at the ON position, a separate line-feed code is re- quired to obtain a line feed. If you move this switch to the OFF position, the printer performs both a carria[...]

  • Page 26

    Option * Option * 10 CPI OFF OFF OFF ON 12 CPI OFF OFF OFF OFF * If there is no Font Card in the slot, Courier style is selected. 18[...]

  • Page 27

    Chapter 2 CONTROL PANEL OPERATIONS The control panel switches can be pressed singly to perform the oper- ations indicated by their names. Other functions can be obtained by holding these switches down when you turn the printer’s power on. Still further functions can be executed by pressing the control panel switches in com- bination. This chapter[...]

  • Page 28

    On Line switch The On Line switch sets the printer on-line and off-line. The state changes each time you press the switch. In the on-line state the printer receives data from the computer and prints the data. In the off-line state the printer stops printing and sends the computer a signal indicating that it cannot accept data. The printer powers up[...]

  • Page 29

    Quiet Mode switch This switch operates off-line to select the printing mode. The printer powers up in normal printing mode. To select the quiet mode, press the On Line switch to go off-line, then press the Quiet Mode switch. The printer will make two passes for each line, resulting in reduced sound (and slower printing). To switch the quiet mode of[...]

  • Page 30

    The selections cycle in the following order when using the Quiet Mode switch: Pica (10 characters per inch) Elite (12 characters per inch) Semi-condensed (15 characters per inch) Condensed pica (17 characters per inch) Condensed elite (20 characters per inch) Proportional Condensed proportional When using the Paper Feed switch, the selections cycle[...]

  • Page 31

    Stay in pane/ pitch: Style/Pitch and Paper Feed switch By holding these switches down during power-up, you can prevent software interference with the print pitch selected from the control panel. You will hear an acknowledging beep as power comes on. After the beep tone, you can set the printer off-line, select a print pitch, then return to on-line [...]

  • Page 32

    If your system passes the codes directly to the printer without changing them, you will get a printout like Figure 2-3. 00 01 02 03 04 05 06 07 08 09 OA 08 OC OD OE OF 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 24 25 26 27 28 29 2A 25 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 38 3C 3D 3E 3F 40 41 42 43 44 45 46 47 48 49 4A 48 4C[...]

  • Page 33

    F ,. Coding for IBM-PC with color adaptor: 20 GOSUB 100 100 O=INP(&H379) :IF 0<128 THEN 100 110 OUT &H378,1 :OUT &H37A,5 :OUT &H37A,4 120 RETURN SWITCH COMBINATION FUNCTIONS Several additional functions can be obtained by pressing the control panel switches in combinations. Reverse micro-feed Clearing the buffer Figure 2-5. Switc[...]

  • Page 34

    Page feed: Paper Feed and On Line switches If you are using single sheets, this operation ejects the current page. If you are using fanfold forms, it feeds to the top of the next page. 1. Press the On Line switch to set the printer off-line. 2. Press the Paper Feed switch and hold it down. The printer will start performing successive line feeds. 3.[...]

  • Page 35

    C/earing the buffer: On Line and Style/Pitch switches When DIP switch 2-l is ON, the printer stores received data in a large memory buffer. This creates a problem when you want to abandon a printing job and restart: the printer may be holding much more data in its buffer than it has actually printed, and this unprinted data must be cleared out befo[...]

  • Page 36

    MEMO[...]

  • Page 37

    Chapter 3 USING THE PRINTER WITH COMMERCIAL SOFTWARE There is an abundance of commercial software available: spreadsheet programs, word-processing programs, graphics programs, and more. This printer will work with any program that supports a Star, Epson or IBM dot-matrix printer. Before using the printer with commercial software, however, there are[...]

  • Page 38

    Selecting (or describing) a printer is the main step in the installation process and frequently the only step necessary. If you selected this printer or any Star, Epson or IBM printer you should be able to use software commands for all the standard printer functions, including bold or dou- ble-strike printing, underlining, subscripts, superscripts,[...]

  • Page 39

    Initialization sequence One of the installation options may be to specify the commands your software sends at the beginning of each printing job. These commands are called the “initialization sequence” or “setup string.” If necessary, you can use the initialization sequence to adjust the margins to your paper size or select a particular typ[...]

  • Page 40

    Type style and pitch selection If your software does not control the type style and pitch, you must make these selections on the control panel. The default selections depend on the settings of DIP switches 2-5 to 2-8. If you want a different style or pitch, proceed as follows: 1. Hold the Style/Pitch and Quiet Mode switches down when you turn the p[...]

  • Page 41

    1 Most printer commands consist of the escape code followed by one or more letters or numbers. Some examples are: <ESC>Wl Double-width characters <ESC>WO Normal width <ESC>4 Italic <ESC>5 Upright Two lines with these commands embedded are shown below, together with the printed result. File: <ESC>WlPRINTER COMMANDS<E[...]

  • Page 42

    MEMO[...]

  • Page 43

    C hapter 4 USING THE PRINTER WITH DOS AND BASIC Although you will probably do most of your printing with the aid of commercial software, at times you will want to employ direct commands or programs of your own. This chapter will give you some ideas. Three subjects are covered: l Hard-copying the screen l Programming the printer with DOS commands l [...]

  • Page 44

    To switch printer output off, press CTRL-PRTSC or CTRL-P again. Each time you press this key combination, hard copy toggles from on to off or from off to on. PROGRAMMING THE PRINTER WITH DOS COMMANDS If your system includes the file PRINT.COM you can use the main DOS printing command. Simply type the word PRINT followed by the name of the file you [...]

  • Page 45

    If you want a particular type style or print pitch you can make these settings from the control panel before you start printing. See Chapter 2. If you print from the DOS command level very often, it will be ad- vantageous to create a printer setup file. Then instead of setting pitches etc. manually each time, you can complete the setup with a singl[...]

  • Page 46

    l:*-V[xl-V[!-VAV[XVLl 2-*-c! . - *E ^V indicates that the following character is a control code. ^V[ enters the < ESC > code. < ESC > has character code 27, and “r’ is the 27th character in ASCII sequence from A. Similarly, ^VA enters the control code < 1 > and “VL enters the control code < 12 > . See your DOS manual i[...]

  • Page 47

    1000 1010 1020 1030 1040 1050 1060 1070 1080 1090 1100 1110 1120 1130 1140 1150 1160 1170 1180 1190 1200 1210 1220 1230 1240 1250 1260 1270 1280 1290 1300 1310 1320 1330 1340 1350 1360 1370 1380 1390 1400 1410 1420 1430 1440 1450 1460 1470 1480 1490 1500 1510 1520 1530 1540 1550 ) Set control codes E$=CHR$(27) D$=E$+"xO" L$=E$+"xl&qu[...]

  • Page 48

    1560 LPRINT ES;" ";CHR$(I); 'Increase character space 1570 LPRINT "THE SPACINGS ARE CHANGED" 1580 NEXT I 1590 LPRINT E$;"aO" 'Left justify 1600 LPRINT E$;"3";CHR$(30); 'Set l/6" line spacing 1610 LPRINT EQ;" ";CHI$(O); 'Normal character space 1620 LPRINT :LPRINT 1630 LPRINT [...]

  • Page 49

    2120 2130 2140 2500 2510 2520 2530 2540 2550 2560 2570 2580 2590 2600 2610 2620 2630 2640 2650 2660 2670 2680 2690 2700 2710 2720 2730 2740 2750 2760 3000 3010 3020 3030 3040 3050 3060 3070 3080 3090 3100 3110 3120 3130 3140 3150 3160 3170 3180 3190 3200 3210 3220 3230 3240 3250 NEXT ROW LPRINT ES;"@" END 'Initialize printer ' S[...]

  • Page 50

    3260 DATA 3270 DATA 3280 DATA 3290 DATA 3300 DATA 3310 DATA 3320 DATA 3330 DATA 15, 15, 0, 0, 0, 0, 0, 0, 0, 0 0, 1, 3, 3, 7, 7, 15, 14, 14, 14 14, 15, 7, 7, 7, 3, 0, 0, 0, 0 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 1, 3, 7, 7, 7, 15, 14, 14, 14, 14 14, 7, 7, 3, 3, 15, 15, 15, 0, 0 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 3340 DATA 0, 0, 60,25[...]

  • Page 51

    Actual printing begins in line 1120. Using the preassigned commands, the program prints samples of its different type styles, including a line showing all styles in italics, followed by samples of the print pitches, then some double and quadruple-sized printing. Next comes the central attraction of the program: a line of text printed fourteen times[...]

  • Page 52

    1600 LPRINT E$;"3";CHR$(36); 'Set l/6" line spacing 1610 ' LPRINT ES;" ";CHR$(O); 'Normal character space 1640 ' LPRINT H$;E$;"q";CHR$(l);'OUTLINED";", ";E$;"q";CHR$(O); 1650 ' LPRINT E$;"q";CHR$(2);'SHADOWED";", ";E$;"q"[...]

  • Page 53

    Chapter 5 MAIAITEIVAIVCE AND TROUBLESHOOTING Dust and heat will make any mechanism wear more quickly. The best maintenance is preventive, and the first step is correct location of the printer. This is covered in greater detail in Chapter 1, but in general an environment comfortable for humans is best for both the computer and the printer. Subjects [...]

  • Page 54

    Figure 5-1. Replacing the ribbon cartridge REPLACING THE PRINT HEAD The dot matrix print head has a life of about 200 million dots, or years of normal use. When printing is too light even after replacing the ribbon, you’ll know that the print head has reached the end of its service life. To replace the print head, follow the procedure below. As y[...]

  • Page 55

    - 7. Place the new print head on its support, seating it on the two pins. 8. Thread the new cable the same way as the old, securing it under the tabs on the print head carriage. 9. Plug the cable into the connector, inserting it as far as it will go, Connector screws Prmt head Figure 5-2. Replacing the print head 10. Fasten the print head down with[...]

  • Page 56

    REPLACING THE BATTERY IN THE RAM CARD The optional RAM card has an internal battery that backs up the stored data even when the card is removed from the printer. This battery can be used for more than four years. To avoid losing data from the RAM card, you should replace the battery before the end of its service life. Follow the procedure below. 1.[...]

  • Page 57

    TROUBLESHOOTING n If the printer doesn’t print: l Check the Power and On Line indicators. Both must be on. l Check that the interface cable is securely plugged in at the computer and printer ends. l Make a test print. (Turn power OFF, hold the On Line or Paper Feed switch down, then turn power ON.) If the test print succeeds, the problem is not w[...]

  • Page 58

    n If the printed characters don’t match the characters on the screen: l Check DIP switches 2-2 to 2-4. When these switches are not all ON (back), an international character set is selected and some ASCII symbols are changed to other characters. See Appendix D. l Some software is not able to display international characters on the screen. If you u[...]

  • Page 59

    I : TECHNICAL SPECIFICATIONS n Printing Mechanism Printing method Printing speed Printing direction Text: Dot graphics: Print head Serial impact dot matrix 150 characters per second (draft pica) 50 characters per second (LQ pica) Bidirectional or unidirectional (select- able), logic seeking Unidirectional, logic seeking 24 Pins Life: 200 million do[...]

  • Page 60

    Special features 4 Dot Matrix Size Draft character: LQ characters: Dot graphics: n Character Sets Standard character set IBM character set Download characters International character sets Panel pitch/style lock-in Forward and reverse micro-feed Paper parking Hexadecimal dump 24 x 9 dots (Pica) 24 x 9 dots (Elite) 16 x 7 dots (Semi-condensed) 24 x 9[...]

  • Page 61

    n Type Sty/es and Pitches Type styles Extra-large characters Print pitches Line spacing Column width Pica: Elite: Semi-condensed: Condensed pica: Condensed elite: w Paper Specifications ’ Single sheets Fanfold paper Number of copies Draft 12, Draft 15, Courier 10, Courier 12, Courier 15, Courier proportional, Prestige 10, Prestige 12, Prestige 15[...]

  • Page 62

    1 Electrical Specifications Line voltage 120 VAC + 10% 220 VAC f 10% 240 VAC + 10% Line frequency Power consumption Insulation resistance Dielectric strength (varies according to the country of pur- chase) 50 or 60 Hz Typ. 39W, Max. 135W 10 megohms between AC power line and chassis Withstands 1 kVAC rms at 50 or 60 Hz between AC power line and chas[...]

  • Page 63

    Pin No. Signal Name 10 KCK Direction Function OUT 5-Microsecond Low pulse acknowledees receipt of data. 11 12 BUSY PAPER OUT OUT OUT Low when the printer is ready to accept data. Goes High if the printer runs out of paper. Can be held Low permanently by turning DIP switch l-5 off. 13 SELECTED OUT 14-15 N/C 16 SIGNAL GND High when the printer is on-[...]

  • Page 64

    MEMO - 56[...]

  • Page 65

    PRINTER CONTROL COMMANDS This appendix describes the printer’s control commands. The commands are arranged by function. The name of each command is followed by a table like the one below: Mode ASCII Decimal Hexadecimal <ESC> 3” c‘ ” 1 27 120 49 1B 78 31 Both <ESC> “X” <I> 27 120 1 IB 78 01 Mode: Indicates the mode in w[...]

  • Page 66

    Select LQ characters 1 Mode 1 ASCII 1 Decimal 1 Hexadecimal I <ESC> “x” “ 1 ” 27 120 49 IB 78 31 Both iESC> “X” <I> 27 120 1 IB 78 01 Changes from draft quality to letter quality. Ignored if the printer was set to stay in panel style at power-on. Select LQ type style Mode ASCII Decimal Hexadecimal Both <ESC> “k”[...]

  • Page 67

    Select upright characters Mode ASCII Decimal Hexadecimal Std. <ESC> “ ” 5 27 53 1B 35 IBM < FS > “ ” 5 28 53 1c 35 Stops italic printing and causes subsequent characters to be printed up- right. Ignored if the printer was set to stay in panel style at power-on. Emphasized printing Mode ASCII Decimal Hexadecimal Both <ESC> [...]

  • Page 68

    Stop underlining 1 Mode 1 ASCII 1 Decimal I Hexadecimal I < ESC > “-” "0" 27 45 48 1B 2D 30 Both < ESC > “-” co> 27 45 0 IB 2D 00 Stops underlining. Start overlining Mode ASCII Decimal Hexadecimal < ESC > “ 11 L‘, 31 27 95 49 IB 5F 31 Both < ESC > “_” <I> 27 95 1 IB 5F 01 Causes subsequent [...]

  • Page 69

    CHARACTER SET COMMANDS L Select standard character set pi Selects the standard character set. This is the power-up default in Standard mode if DIP switch l-7 is ON. Select IBM character set ~~ Selects an IBM character set. This is the power-up default in IBM mode if DIP switch 1-7 is OFF. Select character set ##7 Mode ASCII Both <ESC> “7”[...]

  • Page 70

    n Character set n Character set 0 U.S.A 1 France 2 Germany 3 England 4 Denmark I 5 Sweden 6 Italy 7 Spain I 8 Japan 9 Norway 10 Denmark II 11 Spain II 12 Latin America 13 Denmark/Norway The first eight of these character sets (from U.S.A. to Spain I) can be selected as power-up defaults by DIP switches 2-2 to 2-4. Enable printing of all character c[...]

  • Page 71

    CHARACTER SIZE AND PITCH COMMANDS Pica pitch Mode ASCII Decimal Hexadecimal Std. <ESC> “P” 27 80 IB 50 IBM <DC2> 18 12 In Standard mode, changes from either elite or semi-condensed to pica pitch (10 cpi) or from condensed elite to condensed pica (17 cpi). In IBM mode, changes from either elite or condensed to pica (IO cpi). Ignored [...]

  • Page 72

    Condensed printing Mode ASCII Decimal Hexadecimal I <Sl> 15 OF Both <ESC> < SI > 27 15 IB OF I In Standard mode, changes from pica to condensed pica (17 cpi) or from elite to condensed elite (20 cpi). In IBM mode, changes from pica to condensed (17 cpi). Ignored if the printer was set to stay in panel pitch at power-up. Cancel con[...]

  • Page 73

    Caocel one-line expanded printing Mode ASCII Decimal Hexadecimal Both 1 <DC4> I 20 I 14 Stops one-line expanded printing set with < SO > or < ESC > < SO > . Does not cancel < ESC > “W” 1. Select proportional spacing IModel ASCII I Decimal I Hexadecimal I ’ <ESC> “ 33 P “1” 27 112 49 1B 70 31 Both <[...]

  • Page 74

    increase character spacing IModel ASCII I Decimal I Hexadecimal I Std. 1 <ESC> “” n 21 32 n IB 20 n Increases the space between characters by n dots, where n is a number from 0 to 127. Used in microjustification. Select double or quadruple size Mode ASCII Decimal Hexadecimal Both <ESC> “h” n 27 104 n 1B 68 n Selects the size of [...]

  • Page 75

    Select character width Mode ASCII Decimal Hexadecimal Std. I <FS> “E” n 1 28 69 n IIC 45 n Selects a character width according to the value of n as shown below. n Character width 0 Normal-wide 1 Double-wide 2 Triple-wide Select character height, width, and line spacing Mode ASCII Decimal Hexadecimal <ESC> “[” “@” <4> 2[...]

  • Page 76

    Select character type and print pitch Mode ASCII Decimal Hexadecimal IBM < ESC > “I” n 27 73 n 1B 49 n Selects a combination of character type and print pitch according to the value of n as shown below. n Character type Print pitch 0 Resident Draft Pica 8 Resident Draft Elite 16 Resident Draft Condensed 2 Resident LQ Pica 10 Resident LQ E[...]

  • Page 77

    Set line spacing to 116 inch Mode ASCII Decimal Hexadecimal Std. 1 < ESC > “2” 27 50 IB 32 IBM <FS> “2” 28 50 IC 32 Sets the distance the paper advances or reverses in subsequent line feeds to l/6 inch. Set base unit for line spacing Mode ASCII Decimal Hexadecimal < ESC > “1.. “‘1 <4> 27 91 92 4 1B 5B 5C 04 IB[...]

  • Page 78

    Define line spacing to n/72 inch Mode ASCII Decimal Hexadecimal IBM <ESC> “A” n 27 65 n 1B 41 n Defines the distance the paper advances or reverses in subsequent lines feeds to n/72 inch, where n is between 1 and 85. If n = 0, this command is ignored. The new line spacing does not take effect until the next < ESC > “2” command. [...]

  • Page 79

    Perform one n/780-inch or n/276-inch line feed Mode ASCII Decimal Hexadecimal Both <ESC> “J” n 27 74 n 1B4A n Feeds the paper once by n/180 inches (Standard mode) or n/216 inches (IBM mode), where n is between 0 and 255. Does not move the print position right or left when DIP switch 1-2 is OFF; returns the carriage to the left margin if D[...]

  • Page 80

    Set page Iength to n inches Mode ASCII Decimal Hexadecimal Both <ESC> “C” co> n 27 67 0 n 1B 43 00 n Sets the page length to n inches, where n is between 1 and 22 in Standard mode or between 1 and 127 in IBM mode. The current line becomes the top of the page. Set fop margin Mode ASCII Decimal Hexadecimal Both <ESC> “C" n 2[...]

  • Page 81

    Disable paper-out detector Mode ASCII Decimal Hexadecimal Both 1 <ESC> “8” 1 21 56 IIB 38 Causes the printer to disregard the signal sent by the paper-out detector. enabling printing to the bottom of the paper. Overrides the setting of DIP switch 1-5. Enable paper-out detector Mode ASCII Decimal Hexadecimal Both I <ESC> “9” 127 [...]

  • Page 82

    Select vertical tab channel Mode 1 ASCII Decimal Both 1 < ESC > “i” no I 27 47 n0 Hexadecimal IlB 2F n0 Selects a set of vertical tab stops designated by a channel number (no) from 0 to 7. The tab stops in each channel are set by < ESC > “b”. Vertical tab Mode ASCII Decimal Hexadecimal Both 1 <VT> I 11 1 OB Feeds the paper[...]

  • Page 83

    Sets the right margin at column n in the current character pitch (pica pitch if proportional spacing is currently selected). Column n becomes the last character position in the line. The right margin does not move if the character pitch is changed later. The right margin must be within the limits below: Pica 4snn80 Elite 5sns96 Semi-condensed 6 sn [...]

  • Page 84

    Backspace Mode ASCII Decimal Hexadecimal Both CBS> 8 08 Moves the print position one column to the left. Ignored if the print position is at the left margin. This command can be used to overstrike or combine characters. Left justify Mode ASCII Decimal Hexadecimal <ESC> “a” “0” 27 91 48 1B 61 30 Both <ESC> “a” co> 27 97[...]

  • Page 85

    Set horizontal tab stops Mode ASCII Decimal Hexadecimal Both I <ESC> “D” nl n2 . ..<O> 27 68 nl n2... 0 IB 44 nl n2...00 Cancels all current horizontal tab stops and sets new tab stops at columns nl, a?, etc. in the current character pitch (pica pitch if proportional spacing is currently selected), where nl, ~2, etc. are numbers bet[...]

  • Page 86

    Relative horizontal tab Mode ASCII Decimal Hexadecimal Std. <ESC> I“’ nl n? 21 92 nl n2 1B 5C nl n2 IBM < FS > “” nl n2 28 92 nl n2 1C 5C nl n2 Moves the print position right or left a specified distance (maximum 6 inches). Ignored if the resulting position is beyond the right or left margin. The formulas for the distance and[...]

  • Page 87

    GRAPHICS COMMANDS Print 8-bit sing/e-density graphics Mode ASCII Decimal Hexadecimal <ESC> “K” nl n2 27 15 nl n2 Both 1B 4B nl n? ml m2 ___ ml m2 ml m? Prints 8-bit dot graphics at 60 dots per inch horizontally. The graphic image is 8 dots high and nl + n2 x 256 dots wide. Maximum width is 8 inches (480 dots). ml, m2, . . . are the dot da[...]

  • Page 88

    Print 24bit hex-density graphics Mode ASCII Decimal Hexadecimal < FS > “2” nl n2 28 90 nl ni’ 1C 5A nl n2 Both ml m2 m3 ___ ml m2 m3 ml m2 m3 ___ Prints 24-bit dot graphics at 360 dots per inch horizontally. The graphic image is 24 dots high and nl + nZ x 256 dots wide. Maximum width is 8 inches (2880 dots). In the data ml, m2, m3 . . .[...]

  • Page 89

    Select graphics mode Mode ASCII Decimal Hexadecimal “ ” nl 27 91 103 nl IBM <ESC> “[” g 1B SB 67 nl n2 m0 ml m2 n2 m0 ml m2... n2 m0 ml m2 .,. Selects one of eight graphics modes depending on the value of m(J and prints dot graphics in this mode. The graphic image is (nl + nZ x 256) - 1 dots wide. See <ESC> “K” (for &bit[...]

  • Page 90

    Define download characters Mode ASCII Decimal Hexadecimal <ESC> “I%” co> nl 27 38 0 nl 1B 26 00 nl Std. n2 m0 ml m2 n2 m0 ml m2 n2 m0 ml m2 dl d2 dx dr dz dx dr d.? dx <ESC> “=” -co> nl 21 61 0 nl 1B 3D 00 nl IBM n2 m0 ml m2 n2 m0 ml m2 n2 m0 ml m2 dl d2 . dx dl d.2 dx dl dz? . . . dx Defines one or more new characters and[...]

  • Page 91

    Select ROM character set Mode ASCII Decimal Hexadecimal <ESC> “O,o” “0” 21 37 48 IB 25 30 Both <ESC> ‘C% 93 <o> 27 37 0 1B 25 00 Stops using the download character set and returns to the built-in ROM character set. Ignored when DIP switch 2-l is ON. OTHER PRINTER CONTROL COMMANDS Set MS6 to 7 Mode ASCII Decimal Hexadecim[...]

  • Page 92

    Cancel last line Mode ASCII Decimal Hexadecimal Both <CAN> 24 18 Deletes the last line currently present in the print buffer. Repeat data Mode ASCII Decimal Hexadecimal <ESC> “v” n dl 27 86 n dl 1B 56 n dl Both dz dx dz __.... dx dz . . . . . . dx < ESC > “V” co> 27 86 0 1B 56 00 Repeats data, defined by dr, d.?, . . . [...]

  • Page 93

    Cancel immediate print Mode ASCII Decimal Hexadecimal c ESC > “i” “0” 27 105 48 1B 69 30 Both c ESC > “i” co> 27 105 0 1B 69 00 Cancels the immediate print mode. The printer waits for each line to be completed before printing it, and does not scroll the paper up and down. This command is ignored when friction feed is used. Set [...]

  • Page 94

    Bidirectional printing Mode ASCII Decimal Hexadecimal <ESC> “U” “0” 27 85 48 1B Both 55 30 <ESC> “II” co> 27 85 0 1B 55 00 Causes subsequent printing to be done in the normal bidirectional mode, which is faster than unidirectional printing. Unidirectional printing Mode ASCII Decimal Hexadecimal <ESC> “U” “ 1?[...]

  • Page 95

    Eject paper from ASF Mode ASCII Decimal Hexadecimal <ESC> <EM > “R” 21 25 82 1B 19 52 Both s.(,, ccr “R” “)” “)” 40 40 82 41 41 28 28 52 29 29 Ejects the current page. Ignored if DIP switch l-4 is ON (ASF inactive). Set print start position on ASF Mode ASCII Decimal Hexadecimal <ESC> <EM> “T” n 21 25 84 n[...]

  • Page 96

    MEMO[...]

  • Page 97

    Appendix c DOWNLOAD CHARACTER GENERATOR With this printer you can create new characters and symbols, download their dot data, and have them printed in place of selected characters in the regular character set. Characters that can be generated in this way range from simple but useful symbols like the check mark through complex Chinese or Japanese ch[...]

  • Page 98

    The normal character height is 24 cells, and the width is varied by the character mode as shown below. Character mode Character width Draft characters 9 LQ pica characters 29 LQ elite characters 23 LQ semi-condensed LQ proportional :: Figure C-l shows the matrix with the telephone symbol filled in. Note ihat there are no pairs of horizontally adjac[...]

  • Page 99

    I : By moving the cursor and pressing the Fl, F2, and F3 keys you can quickly build up the dot pattern. If necessary you can clear all dots by pressing F4 and start over. When the character is complete, press Return to store the dot data in the computer’s memory. The program will clear the character box and ask you to select the next character to[...]

  • Page 100

    If you select super/subscript, the character box now has 16 (high) x 7 (wide) dot positions for draft characters, or 16 x 23 dot positions for LQ characters. Each dot is represented by two adjacent solid blocks, occupying its own position and the position to the right. This reflects the fact that the printer still cannot print horizontally adjacent[...]

  • Page 101

    1250 1260 1270 1280 1290 1300 1310 1320 1330 1340 1350 1360 1370 1380 1390 1400 1410 1420 1430 1440 1450 1460 1470 1480 1490 1500 1510 1520 1530 1540 1550 1560 1570 1580 1590 1600 1610 1620 1630 1640 1650 1660 1670 16.30 1630 1700 1710 1720 1730 1740 1750 1760 1770 1780 1790 1800 1810 1820 1830 1840 1850 1860 ~ 1870 1880 IF HID$(I$,2,1)="p&quo[...]

  • Page 102

    I 1890 1900 1910 1920 1930 1940 1950 1960 1970 1980 1990 2000 2010 2020 2030 2040 2050 2060 2070 2080 2090 2100 2110 2120 2130 2140 2150 2160 2170 2180 2190 2200 2210 2220 2230 2240 2250 2260 2270 2280 2290 2300 2310 2320 2330 2340 2350 2360 2370 2360 2390 2400 2410 2420 2430 2440 2450 2460 2470 24.90 2490 2500 2510 2520 SO$="Continue" :S[...]

  • Page 103

    2530 2540 2550 2560 2570 2580 2590 2600 2610 2620 2630 2640 2650 2660 2670 2680 2690 2700 2710 2720 2730 2740 2750 2760 2770 2780 2790 2800 2810 2820 2830 2840 2850 2860 2870 2880 2890 2900 2910 2920 2930 2940 2950 2960 2970 2980 2990 3000 3010 3020 3030 3040 3050 3060 3070 3080 3090 3100 3110 3120 3130 3140 3150 3160 IF Y<Al THEN DT(X,Y+l)=O :C[...]

  • Page 104

    3170 IF FL=0 THEN A(CC)=-1 3180 BEEP 3190 CC=CC+l : IF CC=127 THEN CC=33 3200 GOT0 1920 3210 I_---__ Wrap-up --------------_--___---------------------------- 3220 CLS :LOCATE 1,l :PRINT "SAVE TO FILE?" 3230 S=O :PX=2 :PY=l :SD$="Yes" :Sl$="No" :GOSUB 2820 3240 IF S THEN 3310 3250 LOCATE 5,lO :PRINT "Output file na[...]

  • Page 105

    CHARACTER SETS This appendix gives tables of the printer’s standard and IBM character sets. The decimal character code of each character is shown in an inset to the lower right of the character. The hexadecimal code can be found by reading the entries at the top and left edges of the table. For example, the character “A” is in column 4 and ro[...]

  • Page 106

    STANDARDCHARACTERSET - 1 - 93 1125 . > N A n N 46 62 78 94 110 126 / -?’ 0 0 <DEL> - 47 1 79 95 111 127[...]

  • Page 107

    0 . -- ” c 1 128 144 160 176 192 1 <DCl> I 1 A 1 1 Q U 3 229 245 Ic -V 230 246 -W 1 I SI- 1231 247 Iu IX Ih Y E <so> * > N * n 142 158 174 190 206 222 238 254 F <SI> / ? 0 0 <DEL> - 143 159 175 191 207 223 239 255 r 17 Ii 99[...]

  • Page 108

    CHARACTER SET #2 U 101 117 v f v 70 86 102 118 I? * . . . I<CR>i = M I 1 m II D - II J 111 I 13 29 61 77 /F/-r- 109 125 E <so> . > j--G- I-G- I-G- l-7 N riir n n N rGi-- 1110 l-i% F <SI> / ? 0 0 15 31 47 63 III 127 100[...]

  • Page 109

    [...]

  • Page 110

    IBM CHARACTER SET #l Hexa- I all decim I D I‘? 13 29 il E <so> 14 30 F < SI > 15 31 Other characters are identical to IBM character set #2. The duplication of control codes enables systems with a 7-bit interface to obtain control functions when the most significant bit is set to 1 by the -=ESC> “ > ” command.[...]

  • Page 111

    ADDITIONAL CHARACTER SET t 24 +I 9 OuL25 -3 26 In IBM mode, additional characters can be printed by special commands. 103[...]

  • Page 112

    INTERNATIONAL CHARACTER SETS When an international character set is selected by DIP switches 2-2 to 2-4 or by a command from software, the following changes are made in the character set: Country 23 24 40 5B 5C 5D 5E 60 7B 7C 7D 7E 9B 9D 1 U.S.A. I FRANCE 1 GERMANY # $ h +I- #$§ o 0 § +I- A a ii -I ’ T-/T-/T 1 ENGLAND rlsie * t -I- A t B 0 1% -[...]

  • Page 113

    INDEX r--- L& Absolute tab, 78 Auto feed, 86 Automatic carriage return, 16 Automatic line feed, 17, 75 Automatic sheet feeder, 6, 16 -- B Backspace, 76 Bail lever, 2, 7, 8, 9, II, 12 Battery, RAM card, 48 BASIC, 23, 38, 92 Beeper, 20, 22, 26, 27, 86 Bidirectional printing, 86 Bit-image printing, 35, 43. 50, 79, 80, 81 Bold printing, 59 Bottom m[...]

  • Page 114

    Irl IBM character sets, 61, 100 - 103 IBM mode, 16, 43 IBM printers, 29 IBM-PC, 24 IC card, 5 Immediate print, 85 Initialization sequence, 31 Installing software, 29 Interface: signals, 54 - 55 specifications, 51 test, 13 International characters, 17. 50, 62, 104 Italic printing, 21, 33, 58 /JI Justification, 76 Eel printing 49 Left margin, 74, 76 [...]

  • Page 115

    Star printers, 29 Style/Pitch switch, 21, 23, 26 Subscripts, 60 Super/subscript character, 91 Superscripts, 60 Tabulation, 50, 73, 74. 77 Test patterns, 12, IS, 22 Top cover, 3, 5 Top margin, 7, 72 Top of page (form), 26, 31, 72 Tractor feed, 9 - 12. 51 Troubleshooting, 49 - 50 Type style, 17, 21, 32, 53, 58, 68 Type style commands, 32 Underlining,[...]

  • Page 116

    COMMAND SUMMARY MODE CONTROL CODE FUNCTION IBM Std. Std. IBM Std. IBM Std. Std. IBM IBM <BEL> Bell CBS> Backspace <HT> Horizontal tab <LF> Line feed <VT> Vertical tab <FF> Form feed <CR> Carriage return <so> <SI> Expanded printing for one line Condensed printing <DC]> <DC2> <DC2> [...]

  • Page 117

    MODE CONTROL CODE FUNCTION PAGE < ESC > “8” Disable paper-out detector < ESC > “9” Enable paper-out detector IBM < ESC > “:” Elite pitch Std. <ESC> “:” <O> ,, co> Copy character set from ROM into RAM card <ESC> “<” One-line unidirectional printing Std. <ESC> “=” Set MSB to 0 IB[...]

  • Page 118

    MODE CONTROL CODE FUNCTION Std. c ESC > “1” nl n2 IBM <ESC> “n” I BM <ESC> “[““” <4> <O> <O> -co> <O> n .._ Select base unit for line spacing IBM < ESC > “[” *‘g” nl n2 rn0 ml m2 Select graphics mode IBM <ESC> “” nl n2 Enable printing of all character codes Relative[...]

  • Page 119

    MODE CONTROL CODE < ESC > “x” < 1 > < ESC > “x” “0” < ESC > “x” “1” <ESC> “-” <O> <ESC> -.w” < l> < ESC > “ - ” “0” <ESC> “A.” ‘$1” IBM <FS> “2” < FS > “3” n IBM <FS> “4” IBM < FS > “5” IBM IFS> “:” &l[...]