English dropdown-ico

Texas Instruments PCM1796 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Texas Instruments PCM1796, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Texas Instruments PCM1796 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Texas Instruments PCM1796. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Texas Instruments PCM1796 should contain:
- informations concerning technical data of Texas Instruments PCM1796
- name of the manufacturer and a year of construction of the Texas Instruments PCM1796 item
- rules of operation, control and maintenance of the Texas Instruments PCM1796 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Texas Instruments PCM1796 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Texas Instruments PCM1796, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Texas Instruments service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Texas Instruments PCM1796.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Texas Instruments PCM1796 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    DEM-DSD1796/PCM1795/PCM1796/PCM1798 DSD1796/PCM1795/PCM1796/PCM1798 Evaluation Module User's Guide Literature Number: SLEU057A September 2004 – Revised May 2009[...]

  • Page 2

    2 SLEU057A – September 2004 – Revised May 2009 Submit Documentation Feedback[...]

  • Page 3

    Contents Preface ............................................................................................................................... 5 1 Description ................................................................................................................ 7 1.1 Functional Block Diagram .............................................[...]

  • Page 4

    www.ti.com List of Figures 1-1 DEM-DSD1796/PCM1795/PCM1796/PCM1798 Block Diagram ...................................................... 8 2-1 DEM-DAI/ASDAC Silkscreen ............................................................................................. 12 2-2 DEM-DAI/ASDAC (Top View) .........................................................[...]

  • Page 5

    Preface SLEU057A – September 2004 – Revised May 2009 Read This First About This Manual This document provides the information needed to set up and operate the DEM-DSD1796/PCM1795/PCM1796/PCM1798 EVM evaluation module, a test platform for the 24-bit, 192-kHz, sampling stereo DSD1796 , PCM1795 , PCM1796 , and PCM1798 audio digital-to-analog conve[...]

  • Page 6

    Trademarks www.ti.com Trademarks All trademarks are the property of their respective owners. Read This First 6 SLEU057A – September 2004 – Revised May 2009 Submit Documentation Feedback[...]

  • Page 7

    Chapter 1 SLEU057A – September 2004 – Revised May 2009 Description The DEM-DSD1796/PCM1795/PCM1796/PCM1798 is an evaluation fixture for the DSD1796/PCM1795/ PCM1796/PCM1798 series of 24-bit, 192-kHz sampling stereo DACs. This EVM provides all necessary connectors and circuitry for interfacing to audio test systems and commercial audio equipment[...]

  • Page 8

    1.1 Functional Block Diagram CN003 Serial Connector I/V 5534a I/V 5534a I/V 5534a I/V 5534a BALAmp 5534a BALAmp 5534a LchOUT (4.5V ) RMS RchOUT (4.5V ) RMS DAI CS8414 SW001 003 ModeControl - S/PDIFIN OPT Coax DSDS1796 PCM1795 PCM1796 PCM1798 DEM-AS/CDACDaughterCard 3.3- V Regulator +VCC (5V) ± ± AVCC ( 15V) 1.2 EVM F[...]

  • Page 9

    1.3 System Requirements 1.4 Electrostatic Discharge Warning 1.5 Function Control for DAI Interface Format 1.6 Reset Operation www.ti.com System Requirements The DEM-DSD1796/PCM1795/PCM1796/PCM1798 EVM has the following requirements: • ± 15-V analog power supply at AVCC+, AVCC–, and GND • 5-V DAC power supply at VCC and GND • S/PDIF input ([...]

  • Page 10

    1.7 SW006 Operation Control for DAC 1.8 Jumper Connection 1.9 Demonstration Software SW006 Operation Control for DAC www.ti.com Switch SW006 is the register set and reset control for the PCM1796 and DSD1796. The RESET section of the switch must be set to H except to perform a reset operation. Table 1-2 shows the options for SW006. Table 1-2. SW006 [...]

  • Page 11

    Chapter 2 SLEU057A – September 2004 – Revised May 2009 Schematics, PCB Layout, and Bill of Materials This chapter provides the DEM-DAI/ASDAC and the DEM-AS/CDAC printed circuit boards and schematics. The bill of materials (BOM) is included for component and manufacturer reference. Note: Board layouts are not to scale. These are intended to show[...]

  • Page 12

    2.1 DEM-DAI/ASDAC Printed Circuit Board Layout DEM-DAI/ASDAC Printed Circuit Board Layout www.ti.com Figure 2-1 through Figure 2-3 illustrate the printed circuit board (PCB) layout for the DEM-DAI/ASDAC. Figure 2-1. DEM-DAI/ASDAC Silkscreen 12 Schematics, PCB Layout, and Bill of Materials SLEU057A – September 2004 – Revised May 2009 Submit Docu[...]

  • Page 13

    www.ti.com DEM-DAI/ASDAC Printed Circuit Board Layout Figure 2-2. DEM-DAI/ASDAC (Top View) SLEU057A – September 2004 – Revised May 2009 Schematics, PCB Layout, and Bill of Materials 13 Submit Documentation Feedback[...]

  • Page 14

    DEM-DAI/ASDAC Printed Circuit Board Layout www.ti.com Figure 2-3. DEM-DAI/ASDAC (Bottom View) Schematics, PCB Layout, and Bill of Materials 14 SLEU057A – September 2004 – Revised May 2009 Submit Documentation Feedback[...]

  • Page 15

    2.2 DEM-AS/CDAC Printed Circuit Board Layout www.ti.com DEM-AS/CDAC Printed Circuit Board Layout Figure 2-4 through Figure 2-6 illustrate the PCB layout for the DEM-AS/CDAC. Figure 2-4. DEM-AS/CDAC Silkscreen Figure 2-5. DEM-AS/CDAC (Top View) SLEU057A – September 2004 – Revised May 2009 Schematics, PCB Layout, and Bill of Materials 15 Submit D[...]

  • Page 16

    DEM-AS/CDAC Printed Circuit Board Layout www.ti.com Figure 2-6. DEM-AS/CDAC (Bottom View) Schematics, PCB Layout, and Bill of Materials 16 SLEU057A – September 2004 – Revised May 2009 Submit Documentation Feedback[...]

  • Page 17

    2.3 DEM-DAI/ASDAC Schematics R101 220 U101 NJM5534 R105 180 C105 8200pF 2 3 6 4 R1 13 100 C103 0.027uF R109 200 C101 10uF RST MDO MDI MC ML SCLK V CC V CC GND GND (NC) (NC) (NC) (NC) V OUT L V OUT L+ GND GND V OUT R V OUT R+ (NC) AV CC AV CC + (NC) GND GND V DD /16V CLKO BCK LRCK DA T A (NC) MUTE V DD V DD GND GND RESET MDO MDI MC ML AGND D_SCLK CL[...]

  • Page 18

    FFC-4BMEP1 U003 74 VHC14 U004 74HC T32 U002 C Cd/F1 Cc/F0 Cb/E2 Ca/E1 C0/E0 VD+ DGND RXP RXN FSYNC SCK CS12/FCK U 28 27 26 25 24 23 22 21 20 19 18 17 16 15 VERF Ce/F2 SDA T A ERF M1 M0 VA + AGND FIL T MCK M2 M3 SEL CBL C S8414 2 1 3 U001 TORX173 CN001 RCA pj R001 75 C001 0.01uF C002 0.01uF C004 0.1uF C003 10uF /16V C005 10uF /16V C006 0.1uF C007 10[...]

  • Page 19

    2.4 DEM-AS/CDAC Schematics C024 C020 C016 C012 C002 0.1uF V cc 1 (NC) MUTE V DD V DD GND GND RESET MDO MDI MC ML AGND D_SCLK CLKO/D_BCK P_SCLK DSD_R P_BCK P_LRCK P_DA T A DSD_L U002 NJM5534 R005 820 C01 1 2700pF C005 10uF /16V (R003) C014 10uF/16V C013 10uF/16V C010 Jumper (R004) V CC V CC GND GND (NC) (NC) (NC) (NC) V OUT L V OUT L+ GND GND V OUT [...]

  • Page 20

    2.5 Component Lists 2.5.1 DEM-AS/CDAC_96/98 Parts List 2.5.2 DEM-DAI/ASDAC_96/98 Parts List Component Lists www.ti.com Table 2-1 lists the bill of materials for the DEM-AS/CDAC_96/98. Table 2-1. Bill of Materials Qty RefDes Item Value Mfr Part No Manufacturer Remarks 11 C001, C003, C008, AL ELE capacitor 10 µ F/16 V ROA–16V100M ELNA C013, C014, [...]

  • Page 21

    www.ti.com Component Lists Table 2-2. Bill of Materials (continued) Qty RefDes Item Value Mfr Part No Manufacturer Remarks 1 FIL001 Filter Not mounted 1 CN003 L-type connector 57LE40360-7700(D3) Yamaichi 1 CN004 48-pin connector FFC-48BMEP1 Yamaichi CN002, CN058, 3 2-pin connector FFC-2BMEP1 Yamaichi JP002 1 CN104 RCA connector (red) LPR6520-0802 S[...]

  • Page 22

    Revision History Revision History www.ti.com Changes from Original (September, 2004) to A Revision .............................................................................................. Page • Updated document format to current standards ....................................................................................... 5 • Added PC[...]

  • Page 23

    EVALUATION BOARD/KIT IMPORTANT NOTICE Texas Instruments (TI) provides the enclosed product(s) under the following conditions: This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end-product fit for general consumer use. Persons handling th[...]

  • Page 24

    IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders[...]