English dropdown-ico

Toshiba 4200FA XT1 manual

1
2
3
4
5
6
7
8
9
10

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of Toshiba 4200FA XT1, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of Toshiba 4200FA XT1 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of Toshiba 4200FA XT1. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of Toshiba 4200FA XT1 should contain:
- informations concerning technical data of Toshiba 4200FA XT1
- name of the manufacturer and a year of construction of the Toshiba 4200FA XT1 item
- rules of operation, control and maintenance of the Toshiba 4200FA XT1 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of Toshiba 4200FA XT1 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of Toshiba 4200FA XT1, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the Toshiba service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of Toshiba 4200FA XT1.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the Toshiba 4200FA XT1 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    4200 FA XT1 September 6, 2004 1 TOSHIBA International Corp GUIDE SPECIFICATIONS THREE PHASE UNINTERRUPTIBLE POWER SYSTEM TOSHIBA 4200 FA 50 kVA XT – Transformer / External Battery 208v Input / 208/120v Output UPS GUIDE SPECIFICATIONS[...]

  • Page 2

    4200 FA XT1 September 6, 2004 2 (50 kVA XT) 1.0 SCOPE 1.1 System This specification describes a conti nuous duty, three-phase, on-line, solid- state uninterruptible power supply system, hereafter referred to as the UPS. 2.0 SYSTEM DESCRIPTION 2.1 Applicable Standards The UPS shall be designed in accor dance with and be compliant with the following [...]

  • Page 3

    4200 FA XT1 September 6, 2004 3 H. Input / Output EMI / RFI Filters 2.3 System Operation The UPS shall operate as an on-line, fully automatic system in the following modes: A. NORMAL - Incoming AC power is boosted using a chopper circuit, and converted into DC power. The DC power is then used to charge the battery bank while at the same time provid[...]

  • Page 4

    4200 FA XT1 September 6, 2004 4 protection against spikes, common/normal mode noise, load steps and frequency shifts (without battery back-up capability). 3.0 SYSTEM PARAMETERS A. UPS Input 1) Input Voltage 208VAC 2) Input Voltage Requirement 3 Phase, 3 Wire + Ground 3) Voltage Variation +10% to -30% 4) Rated Frequency 50/60 Hz 5) Frequency Range 4[...]

  • Page 5

    4200 FA XT1 September 6, 2004 5 +/- 3% (loss or return of input power) +/- 8% (bypass to inverter) 13) Transient Voltage Recovery 50ms maximum to within 2% of nominal 14) Overload Cap. (on inverter) 125% for 90 sec., 150% for 30 sec. 15) Overload Cap. (on bypass) 1000% for 10ms, 125% for 10 min. 16) Crest Factor 3.0 17) Harmonic Voltage Distortion [...]

  • Page 6

    4200 FA XT1 September 6, 2004 6 4.0 FUNCTIONAL DESCRIPTION A. Converter / Charger / DC Chopper DESCRIPTION - The converter/charger s hall consist of a solid-state three phase rectifier, DC to DC converter (chopper), output filter, and transient suppresser network to regulate and maintain DC power to the inverter. 1) TRANSIENT SUPPRESSER - The incom[...]

  • Page 7

    4200 FA XT1 September 6, 2004 7 2) INPUT ISOLATION TRANSFORMER - The inverter network shall incorporate a shielded isolation transfo rmer to provide complete isolation of the load from utility AC, as well as providing attenuation for high frequency noise common mode). Additi onally, the transformer shall have a set of windings to condition the inte[...]

  • Page 8

    4200 FA XT1 September 6, 2004 8 See “System Diagnostics” for specific fault. 3) SYSTEM METERING - The UPS s hall be provided with a single read- out display which displays, upon request, the following information: AC INPUT VOLTAGE (Line to Line) AC OUTPUT VOLTAGE (Line to Line, Line to Neutral) AC OUTPUT CURRENT BATTERY VOLTAGE BATTERY CHARGING[...]

  • Page 9

    4200 FA XT1 September 6, 2004 9 B. Matching Battery Enclosure The battery cabinet shall consist of a freestanding, matching NEMA1 enclosure equipped with casters and leve ling feet. The maximum overall dimensions and weights shall be as follows: UPS Size Dimensions Weight Runtimes 50 kVA 30”L x 32”W x 59.8”H ~1,832 lbs. 4-29 Min C. Cable Entr[...]

  • Page 10

    4200 FA XT1 September 6, 2004 10 D. Battery Test Function The UPS shall be provided with a “Battery Test” pushbutton to periodically check the condition of the batteries. Upon detection of a battery problem, the UPS shall notify the us er of this condition allowing the user to perform a detailed check of the battery string. 7.0 SERVICE AND WARR[...]