Toshiba P500 manual

GMAD00213010 08/09 If you need assistance: ❖ T oshiba’ s Support W eb site pcsupport.toshiba.com ❖ T oshiba Customer Support Center Calling within the United States (800) 457 -7777 Calling from outside the United States (949) 859 -4273 For more in formation, see “If Something Goes Wrong” on page 183 in this gui de. Satellite ® P500 Serie[...]

2 5.375 x 8.375 ver 2.3 Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling . Model: Satellite ® P500 Series Recordable and/or ReWritable Drive(s) and Associated Software W arranty The computer system you purchased may in[...]

3 5.375 x 8.375 ver 2.3 Critical Applications The computer you have purchased is not designed for any “critical applications. ” “Critical applications” means life s upport sy stems, medical applications, connections to implanted medi cal devi ces, commercial transportation, nuclear facilities or systems or an y other applicatio ns where pro[...]

4 5.375 x 8.375 ver 2.3 This device complies with P art 15 of the FCC Rules. Operation is subject to the following tw o conditions: ❖ This device may not cause harmful interference. ❖ This device must accept an y interferen ce received, including interference that may cause undesired operatio n. Contact either: ❖ T oshiba’ s Support W eb si[...]

5 5.375 x 8.375 ver 2.3 Connection to party line service is subject to state tarif fs. Contact the state public utility commission, public se rvice co mmission or corpor ation commission for information. T elephone Company Procedures The goal of the telephone company is to pro vide you with the best service it can. In order to do this, it may occas[...]

6 5.375 x 8.375 ver 2.3 Alarm Equipment If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable yo ur alarm equipment. If you hav e questions abou t what will disable alarm equipment, consult your telephone compan y or a qualified installer . Instructions for IC CS[...]

7 5.375 x 8.375 ver 2.3 Wireless Interoperability The TOSHIB A W ireless LAN Mini PCI Card products are designed to be interoperable with any wireless LAN product that is based on Direct Sequence Spread Spectrum (DSSS) radio technology , and is compliant to: ❖ The IEEE 802.11 Standard on W ireless LANs (Rev ision A/B/G), as defined and approv ed [...]

8 5.375 x 8.375 ver 2.3 Wireless LAN and Y our Health W ireless LAN products, like other radio de vices, emit radio frequency electromagnetic energy . The lev el of energy emitted by W i reless LAN devices howe ver is f ar much less than the elect romagnetic energy emitted by wireless devices lik e for example mobile phones. Because W ireless LAN p[...]

9 5.375 x 8.375 ver 2.3 Canada – Indust ry Canada (IC) This device complies with RS S 210 of Industry Canada. The installer of this radio equipment mu st ensure that the antenna is located or pointed such that it does not emit RF field in exces s of Health Canada limits for the general population; consu lt Safety Code 6, obta inable from Health C[...]

10 5.375 x 8.375 ver 2.3 EU Declaration of Conformity TOSHIB A declares that this product conforms to the follo wing Standards: This product is carrying the CE-Mark in accordance w ith the related European Directiv es. The party responsib le for CE-Marking is TOSHIB A Europe GmbH, Hammfelddamm 8, 41460 Neuss, Ger many . The European Union WEEE (W a[...]

11 5.375 x 8.375 ver 2.3 VCCI Class B Information Modem W arning Notice Conformity Statement The equipment has been ap prov ed to [Commission D ecision “CTR21”] for pan- European single terminal connection to the Public Switched T elephone Network (PSTN). Howe ver , due to dif ferences between the indi vidual PSTNs provided in dif ferent countr[...]

12 5.375 x 8.375 ver 2.3 Using this Equipment in Japan In Japan, the frequency bandwi dth of 2,400 MHz to 2,483.5 MHz for second generation low-po wer data communicatio n systems such as this equipment ov erlaps that of mobile object identifi cation systems (premises radio station and specified lo w-power radio station). 1. Sticker Please put the f[...]

13 5.375 x 8.375 ver 2.3 The indication sho wn belo w appears on this equipment. 1 2.4: This equipment uses a frequency of 2.4 GHz. 2 FH: This equipment uses FH-SS modulation. 3 The interference range of this equipment is less than 10m. 4 This equipment uses a frequenc y bandwidth from 2,400 MHz to 2,483.5 MHz. 3. TOSHIB A Direct PC Monday – Frid[...]

14 5.375 x 8.375 ver 2.3 Radio Approvals for Wireless Devices The following information is de pendent on what type of wi reless de vice is in your computer . Not all devices are avai lable on all models. Approved Countries/Regions for the Intel ® Wireless Wi-Fi ® Link 5100/5300 Series This equipment is approv ed to the radio standard by the count[...]

15 5.375 x 8.375 ver 2.3 Approved Countries/Regions for the Atheros ® Wireless Wi-Fi ® Link AR5B95 Series This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in th e countries/regions in the follow ing table. Malawi Malaysia Malta Martinique Mayotte Mexico Monaco Mont[...]

16 5.375 x 8.375 ver 2.3 Europe - Restrictions for us e of 2.4 GHz Frequencies in European Community Countries Finland France Germany Ghana Greece Guatemala Herzegovina Honduras Hong K ong Hungary Iceland India Indonesia Iraq Ireland Italy Jamaica Japan Jordan Kazakhstan K enya Kuwai t Kyrgyzs tan L atv ia Lebanon Lesotho Liechtenstein Lithuania Lu[...]

17 5.375 x 8.375 ver 2.3 Europe - Restrictions for Use of 5 GHz Frequencies in European Community Countries Dans le cas d’une utilisation privée, à l’extérieur d’un bâtiment, au- dessus d’un espace public, aucun en registrement n’est nécessaire pour une distance de moins de 300m. Pour une distance supérieure à 300m un enregistremen[...]

18 5.375 x 8.375 ver 2.3 O: allowed x: forbidden ❖ T o remain in conformance with Euro pean spectrum usage laws for Wireless LAN operation, the above 2.4 GHz and 5 GHz channel limitations apply . The user should use the wireless LAN utility to check the current channel of operation. If operation is occu rring ou tside of the allow able frequencie[...]

19 5.375 x 8.375 ver 2.3 Approved Countries/Regions for the Realtek ® RTL8192E This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table. Albania Ar gentina Australia Austria Azerbaijan Bahrain Bangladesh Belgium Bolivia Bosnia[...]

20 5.375 x 8.375 ver 2.3 Approved Countries/Regions for the Realtek ® RTL8191SE This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table. Albania Ar gentina Australia Austria Azerbaijan Bahrain Bangladesh Belgium Bolivia Bosni[...]

21 5.375 x 8.375 ver 2.3 Approved Countries/Regions for the Realtek ® RTL8187B This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in th e countries/regions in the follow ing table. U AE (United Arab Emirates) Ukraine United Kingdom Uruguay USA V enezuela V ietnam Zimb[...]

22 5.375 x 8.375 ver 2.3 Approved Countries/Regions for use for the Intel ® PRO/Wireless 3945ABG Network Connection This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in th e countries/regions in the follow ing table. An adhoc mode is available in Ch1- Ch11(802.11b/g)[...]

23 5.375 x 8.375 ver 2.3 Approved Countries/Regions for the Intel ® Wireless Wi-Fi ® Link 4965AGN This equipment is approv ed to the radio standard by the countries/regions in the following table. Do not use this equipment except in th e countries/regions in the follow ing table. An adhoc mode is available in Ch1- Ch11(802.11b/g), An Infrastructu[...]

24 5.375 x 8.375 ver 2.3 Bluetooth ® Wireless T echnolo gy Interoperability Bluetooth ® Cards from TOSHIB A are designed to be interoperable with an y product with Bluetooth wireless technology that is based on Freque ncy Hopping Spread Spectrum (FHSS) radio t echnology , and is compliant to: ❖ Bluetooth Specification as def ined and approv ed [...]

25 5.375 x 8.375 ver 2.3 Approved Countries/Regions for use ( Bluetooth ® wireless technology) Bluetooth ® Card from T oshiba equipment is ap proved to the radio standard by the countries/regions in the follo wing table. Do not use this equipment except in th e countries/regions in the follow ing table. Bluetooth ® Wireless T echnology and Y our[...]

26 5.375 x 8.375 ver 2.3 In some situatio ns or en vironments, the use of Bluetooth wireless technology may be restricted by the proprietor of th e building or responsible representati ves of the organization. These situations may for example include: ❖ Using the equipment with Bluetooth wireless technology on boar d airplanes, or ❖ In any othe[...]

27 5.375 x 8.375 ver 2.3 The legal communications mentioned in the abov e item refer to radio communications operated in accordan ce with telecommunication laws and regulations. Lo w power radio frequency electric machin ery shall resist ag ainst interference from legal communications or from industrial, scientific and medical radio emission electr[...]

28 5.375 x 8.375 ver 2.3 Copyright This guide is copyrighted by T oshiba Amer ica Information Systems, Inc. with all rights reserved. Under the copyright laws, this guide canno t be reproduced in any form without the prior written permission of T o shiba. No patent liability is assumed, howe ver , with respect to the use of the information containe[...]

29 5.375 x 8.375 ver 2.3 T rademarks Satellite, ConfigFree, and eco utility ar e either registered trademarks or trademarks of T oshiba Am erica Information Systems, Inc. and/or T oshiba Corporation. Adobe and Photoshop are either registered trademarks or tr ademarks of Adobe Systems Incorporated in the Unite d States and/or other countries. Athero[...]

30 5.375 x 8.375 v er 2.3 Contents Introduction ................ ................................................................ 38 This guide ...............................................................40 Safety icons ............................................................41 Other icons used ...............................................[...]

31 Contents 5.375 x 8.375 v er 2.3 Turning on the power .......................................51 Setting up your software ...................................52 Registering your computer with Toshiba ................52 Adding optional external devices.............................52 Adding memory (optional) ......................................53 I[...]

32 Contents 5.375 x 8.375 v er 2.3 Using and configuring Sleep mode ...................91 Closing the display panel ..................................94 Customizing your co mputer’s settings ....................94 Caring for your computer ........................................94 Cleaning the computer ......................................94 Mov[...]

33 Contents 5.375 x 8.375 v er 2.3 Removing a disc with the computer on (tray-type drive) ........................................114 Removing a disc with the computer off (tray-type drive) ........................................114 Caring for optical discs ..................................115 Toshiba’s online resources ........................[...]

34 Contents 5.375 x 8.375 v er 2.3 Chapter 4: Exploring Y our Computer’ s Features ................... 134 Exploring the desktop ........................................... 134 Finding your way around the desktop .............135 Setting up for co mmunications .............................137 Connecting your computer to a network .........138 Con[...]

35 Contents 5.375 x 8.375 v er 2.3 Using an instant password ..............................156 Using a supervisor password ..........................157 Using a user password ...................................158 Deleting a user password ................................159 TOSHIBA Face Recognition Utility ......................... 160 TOSHIBA PC D[...]

36 Contents 5.375 x 8.375 v er 2.3 Chapter 6: If Something Goes Wrong ............ ........................ 183 Problems that are easy to fix ................................183 Problems when you turn on the computer ............184 The Windows ® operating system is not working ..187 Using Startup options to fix problems ............ 187 Internet [...]

37 Contents 5.375 x 8.375 v er 2.3 Appendix A: Hot Keys/TOSHI BA Cards ........... ...................... 213 Hot Key Cards .......................................................213 Using the Hot K ey Cards .................................214 Application Cards .................................................. 215 Using the Application Cards ....[...]

38 I n t roduct ion W elcome to the world of powerful, portable, multimedia computing. W ith your T osh iba computer , your work and entertainment can accompan y you where ver you go. Y our co mputer model may be ENERGY ST AR ® compliant. If the model you purchased is compliant, it is labeled with the ENER GY ST AR ® log o on the computer and the[...]

39 Introduction 5.375 x 8.375 ver 2.3 According to the EP A, a computer meeting the new ENERGY ST AR ® specifications will use between 20% and 50% less energ y depending on how it is used. If all U.S. household and businesses replaced old computers with ne w ENERGY ST AR ® qualified models, we would sav e more than $1.8 billion in energy costs ov[...]

40 Introd uctio n This guide 5.375 x 8.375 ver 2.3 The product specifications and configuration information are designed for a product Series. Y our particular model may not have all the features and specifications listed or illustrated. For more detailed information about the features and specifications on your particular model, please visit T osh[...]

41 Introduction Safety icons 5.375 x 8.375 ver 2.3 Safety icons This manual contains safety inst ructions that must be observed to av oid potential hazards that co uld result in personal injuries, damage to your equipmen t, or loss of data. These safety cautions hav e been classif ied according to the seriousness of the risk, and icons highlight th[...]

42 Introd uctio n Other documentation 5.375 x 8.375 ver 2.3 Y our computer’ s features and specifications Certain computer chassis are de signed to accommodate all possible configurations for an entire product Series. Y our select model may not ha ve all the features and speci fications correspond ing to all of the icons or switches shown on th e[...]

43 Chapter 1 Getting Started This chapter provides tips for us ing your computer ef fecti vely , summarizes how to connect components, and explains what to do the first time you use your computer . The “Instruction Manual for Safet y and Comfort, ” that is shipped with your computer, contains impo rtant safety information. Please read the safet[...]

44 Getting Started Selecting a place to work T o keep your computer in prime operating condition, protect you r work area from: ❖ Dust, moisture, and direct sunlig ht. ❖ Equipment that generates a strong electromagnetic field, such as stereo speakers (other than speakers that are connected to the computer) or speakerphones. ❖ Rapid changes in[...]

45 Getting Started Selecting a place to work ❖ Avoid prolonged physical contact with the underside or s urface of the computer . ❖ Computer base and palm rest can become hot! Avoid prolonged contact to prevent heat injur y to skin. Read the “ A void e xtended contact between computer base/palm rest and skin” section in the “Instruction Ma[...]

46 Getting Started Setting up your computer Important information on your computer’ s cooling fan Y our computer may have a CPU cooling fan that coo ls the CPU by drawing outside air into the computer . Always mak e sure your compute r and AC adapt or have adequate ventilation and are protected from overheating when the power is turne d on or whe[...]

47 Getting Started Connecting to a po wer sour ce Please handle your computer carefully to avoi d scratching or damaging the surface. Connecting to a power source Y our computer requires power to operate. Use the po wer cord/cable and A C adaptor to connect the comput er to a liv e electrical outlet, or to charge the computer’ s battery . Never p[...]

48 Getting Started Connecting to a power so ur ce T o connect A C power to the computer: 1 Connect the po wer cord/cable to the A C adaptor . (Sample Illustration) Connecting the power cord/cable to the A C adaptor Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other [...]

49 Getting Started Char ging the main battery The computer’ s main battery light gives you an indication of the main battery’ s current char ge: ❖ Glows amber while the main battery is bei ng charged (A C adaptor connected) ❖ Glows white when the main battery is fully charged ❖ Is unlit when t he main battery has d ischarged, the battery [...]

50 Getting Started Using the computer for the fir st time Battery life and charge time may var y depending on the applications, power management settings, and features used. Using the computer for the first time The computer is now ready for you to turn it on and be gin using it. Opening the display panel 1 Facing the front of the com puter, locate[...]

51 Getting Started Using the computer for the f irst time Small bright dots ma y appear on your screen displa y when you turn on your computer . Y our disp lay contains an extremely large number of thin-film transistors (TFT) and is manufactured using high- precision technology . An y small bright dots that may appear on your display are an intrins[...]

52 Getting Started Re gistering your computer with T oshiba Setting up your software When you turn on the computer for the first time, do not turn off t he power again until the operating system has loaded completely . The names of windows displa yed, and the order in which windows appear , may va ry acco rding to your software setup c hoices. The [...]

53 Getting Started Adding memory (optional) ❖ Install an ExpressCard ® (see “Using an ExpressCard®” on page 145 ) Adding memory (optional) HINT : T o purchase additional memory modules, see the accessories information packaged with your system or visit accessories.toshiba.com . Y o u r c o m pu t e r comes with enough memory to run most of [...]

54 Getting Started Adding memory (optional) Before you install or remove a memory module, turn off the computer using the Start menu. If you install or remove a memory module while the computer is in Sleep or Hibernation mode, data will be lost. For this model, Slot A is the bottom slot. Slot B is the top slot. If only one memory module is to be in[...]

55 Getting Started Adding memory (optional) (Sample Illustration) Locati ng the memory module slot cover 6 Using a small Phillips screwdri ver , loosen the captiv e screws that secure the memory module slot co ver . (Sample Illustration) Removing the memory module slot cover 7 Remove the memory module slot cover . 8 Place the scre ws and the co ver[...]

56 Getting Started Adding memory (optional) Avoid touch ing the connector on the memory module or on the computer . Grease or dust on the connector may cause memor y access problems. 9 Carefully remove the ne w memory module from its antistatic packaging, without t ouching its connector . 10 Locate an empty memory module slot on the underside of th[...]

57 Getting Started Adding memory (optional) 12 Firmly press the mem ory module into the memory slot’ s socket at approximately a 30-de gree angle (to the horizontal surface of the computer). (Sample Illustration) Inserti ng the memory m odule into the so ck et 13 Once the module’ s connector is fu lly inserted into the socket, press downw ard o[...]

58 Getting Started Adding memory (optional) (Sample Illustration) Inserting the memory m odule into the slot For this model, Slot A is the bottom slot. Slot B is the top slot. If only one memory module is to be installed, it must be installed in Slot A. 14 Replace the memory modu le slot cov er and secure it using the screws. 15 Re-insert the main [...]

59 Getting Started Adding memory (optional) Removing a memor y module If you need to remov e a memory modul e: 1 Complete steps 1 – 8 in “Installing a memory modu le” on page 53 to shut down the computer an d open the memo ry module slot cov er . Do not try to remove a memor y module with the computer turned on. Y ou can damage the computer a[...]

60 Getting Started Adding memory (optional) 3 Gently lift the me m o ry module to a 30-degree angle and slide it out of the slot. (Sample Illustration) Removing the memory module 4 Replace the memory modu le slot cov er and secure it using the screws. 5 Re-insert the main battery . For more information on inserting the main battery , see “Inserti[...]

61 Getting Started Recovering the Internal Stora ge Drive From time to time, Windows ® will display a pop-up that says, “Do you want to allow the following program to make changes to this computer?” This is a security feature to prevent programs or people from doing things on your computer without your permission. If you were trying to perform[...]

62 Getting Started Recovering the Internal Stor age Drive ❖ During the internal storage drive recovery process it is strongly recommended that your computer be connected to an external power source via the AC adaptor . ❖ It is strongly recommended that you create recov er y DVDs/media before using your system for the first time. For more inform[...]

63 Getting Started Recovering the Internal Stora ge Drive 4 A warning screen appears, statin g that when the reco very is ex ecuted all data will be deleted and rewritten. Click Ye s to continue. (Sample Image) W arning screen 5 When the T oshiba Recov ery W i zard opens and the Selecting a process screen displays, select Recovery of F actory Defau[...]

64 Getting Started Recovering the Internal Stor age Drive 6 The Recov ery of Factory Defaul t Software screen appears. Select Recover to out-of-box state . (Sample Image) Reco very of F a ctory Default Software scr een 7 Click Next . A confirmation message displays reminding you that all data will be lost during the recovery process. Be sure to sa [...]

65 Getting Started Recovering the Internal Stora ge Drive The “Recov er to a custom size pa rtition” option restores you r C: dri ve to its out-of-box state, and allows you to specify the size for the C: partition. Y ou can resize an d recover the C: driv e using the utilities stored on y our computer’ s internal storage driv e or using recov[...]

66 Getting Started Recovering the Internal Stor age Drive 5 When the T oshiba Recov ery W izard opens and the Selecting a process screen displays, select Recovery of F actory Default Software and then click Next . (Sample Image) Selecting a Pr ocess scr een 6 The Recov ery of Factory Defaul t Software screen appears. Select Recover to a custom size[...]

67 Getting Started Recovering the Internal Stora ge Drive 8 Click Next . A confirmation message displays reminding you that all data will be lost during the recov ery process. Be sure to sav e your work to e xternal media before proceeding. 9 Click Next to be gin the recovery . When the process is complete, a message displays indicating that the C:[...]

68 Getting Started Recovering the Internal Stor age Drive 4 A warning screen appears stating that when the recovery is ex ecuted all data will be deleted and rewritten. Click Ye s to continue. (Sample Image) W arning screen 5 When the T oshiba Recov ery W izard opens and the Selecting a process screen displays, select Recovery of F actory Default S[...]

69 Getting Started Recovering the Internal Stora ge Drive 6 The Recov ery of Factory Defaul t Software screen appears. Select Recover without changing the hard drive partitions . (Sample Image) Reco very of F a ctory Defa ult Software scr een 7 Click Next . A confirmation message displays reminding you that all data on the C: dri ve will be lost du[...]

70 Getting Started Recovering the Internal Stor age Drive T o create recov ery D VDs/media: 1 Click Start , All Programs , My T oshiba , and then R ecovery Media Creator . 2 Select DV D (to create Recovery media on D VD). 3 Select the items you want to copy to D VD by clicking the check box next to each item’ s N ame—recov ery files, applicatio[...]

71 Getting Started Recovering the Internal Stora ge Drive W ith recov ery media, you can: ❖ Recov er to out-of-box state ❖ Recov er to a custom size partition ❖ Recov er without changing the in ternal storage driv e partitions For more information on these options, see “Recovering the Internal Storage Dri ve” on page 61 . T o recov er you[...]

72 Getting Started Erasing the Internal Stora ge Drive 9 Follo w the on-screen instructions to comp lete the recovery process. When the process is complete, a message displays, indicating that the dri ve has been recov ered. 10 Press any k ey on the keyboard to restart the computer . Erasing the Internal Storage Drive Erasing the internal storage d[...]

73 Getting Started Erasing the Internal Storag e Drive 3 Choose one of the following options on the Erase the hard disk screen: ❖ Delete all data and parti tions from the hard disk —This option deletes all of the data on the in ternal storage drive without overwriting the dri ve. ❖ Delete all partitions an d ov erwrite all sectors on the hard[...]

74 Getting Started Checking the inte rnal stor age drive operating status Checking the internal storage drive operating status After restoring your inte rnal storag e driv e, you can check its status as follo ws: 1 Click Start . 2 Right-click Computer . 3 Select Manage . 4 Click Disk Manageme nt . 5 Highlight the internal storage dri v e in the V o[...]

75 Getting Started Using the T ouchP ad™ Using the T ouchPad™ Some of the T ouchPad operations described in this section are supported in certain applications only . Y ou can use the T ou chPad™ (the small, touch-sensiti ve area in front of the ke yboard) and th e adjacent control buttons to: ❖ Mov e the pointer on the screen ❖ Select an [...]

76 Getting Started Using the T ouchP ad™ Select a n item 1 Move the pointer to the item you want to select. 2 Do one of the following: ❖ T ap the T ouchp ad once OR ❖ Press and release the primar y (left-hand) control button (Sample Illustration) T ap once to select Open or activate an item 1 Move the pointer to the item you want to open/acti[...]

77 Getting Started Using the T ouchP ad™ Scroll continu ously (Circular scrolling) 1 Begin scrolling vertically or horizonta lly by sliding your finger along the right or bottom edge of the T ouchPad as described above. 2 Without lifting your finger from the T ouchPad, start movi ng your finge r in a circular motion on the T ouchPad. 3 T o scroll[...]

78 Getting Started Using the T ouchP ad™ Adjusting T ouchPad™ settings While you are typing, the mo use pointer may seem to move or jump around “by itself” to random locations on the screen. The mouse pointer may also seem to automati cally select te xt, click buttons, and activ ate other user interface elements. For he lp with these proble[...]

79 Getting Started Using external display de vices Using external display devices Y our computer comes with a built-in display , but you can also connect the following types of external display devices to the video ports described below: ❖ An HDMI™-compatible television or VCR/D VD player via the HDMI Out port * ❖ An external monitor or proje[...]

80 Getting Started Using external display de vices Refer to the manual that came with the television for more information. Y our computer will automaticall y detect the external display devic e and activ ate a scr een with display options. Connecting to a TV using HDMI™-CEC (A vailable on certain models) HDMI™-CEC (Consumer Electronics Co ntrol[...]

81 Getting Started Using external display de vices 4 T urn on the external de vice. Y our computer will automaticall y detect the external display devic e and acti vate a scr een with display options. In the future you can change the display settings by pressing Fn+F5 , or by configuring the display properties settings. Directing the display output[...]

82 Getting Started Using an e xternal ke yboar d ❖ Swap—Swi tch primary disp lay between internal display and external monitor when using extended desktop (Sample Image) Display options window 3 Release the Fn key . Adjusting the quality of the external display T o obtain the best picture quality from your television (or other video display dev[...]

83 Getting Started Connecting a printer Connecting a printer Y our printer documentation may require you to install the printer software before physically connecting the printe r to your computer . If you do not install the software as instructed by the printer manufacturer , the printer may not function correctly . Read the documentation that came[...]

84 Getting Started T urning off the computer Setting up a printer Some printers require a specific installation process. Refer to your printer installation guide for instructions before completing the following procedure. If your printer does not support Plug and Play , follo w these steps to set it up for the first time. Y ou only need to set up t[...]

85 Getting Started T urning off the computer Options for turning off the computer Depending on the operating sy stem installed, you have more than one option av ailable for turning off the computer: Shut down, Hibernate, and Sleep. Each option has its advantages. ❖ Use the Shut down or Hibernate command if you will not be using the computer for s[...]

86 Getting Started T urning off the computer For information on ho w to use and configure Hibernation mode see “Using and configuring Hibernation mode” on page 89 . Sleep mode The Sleep command places the comput er into a power -saving mode. Sleep sa ves the current state of the computer to memory so that, when you restart the comp uter , you c[...]

87 Getting Started T urning off the computer Using the Shut down command The Shut do wn command complet ely shuts down the computer without saving your work or the cu rrent state of th e computer . This command closes all open program s, shuts down the operating system, and then turns of f your computer . T o turn off your computer using the Shut d[...]

88 Getting Started T urning off the computer 3 Click Change advanced power settings . The Advanced settings tab of the Po wer Options window appears. 4 Double-click P ower b uttons and lid to display the actions that you can configure. (Sample Image) Advanced settings tab of P ower Options screen 5 Select the options you want from the drop-down lis[...]

89 Getting Started T urning off the computer Restarting your computer T o start the computer up again, press the po wer b utton unti l the ON/OFF light glows white. If you turn off the computer by closing the display panel, you can start it again by open i ng the display panel . Using and configuring Hibernation mode T o turn off the com puter usin[...]

90 Getting Started T urning off the computer 2 Click Change pl an settings under the power plan to be customized. The Edit Plan Settin gs window appears. 3 Click Change advanced power settings . The Advanced settings tab of the Po wer Options window appears. 4 Double-click P ower b uttons and lid to display the actions that you can configure. (Samp[...]

91 Getting Started T urning off the computer 6 Click App l y . 7 Click OK . Once the computer is conf igured, you can place it into Hibernation mode by either pressing the po wer button or closing the display panel, depending on the Hibernation options set. Starting again from Hibernation mode T o start up the computer from Hibernation mode, press [...]

92 Getting Started T urning off the computer Configuring Sleep mode options Y ou can place the computer into Sleep mode by either pressing the power b utton or closing the display panel. Y ou can also specify an amount of time after which the computer au tomatically g oes into Sleep mode. T o use any of these methods, you f irst need to enable them[...]

93 Getting Started T urning off the computer 4 Click Change advanced power settings . The Advanced settings tab of the Po wer Options window appears. 5 Double-click P ower b uttons and lid to display the actions that you can configure. (Sample Image) Advanced settings tab of P ower Options scr een 6 Select Sleep for the options you want. These opti[...]

94 Getting Started Customizing your comp uter’ s settings Starting again from Sleep mode T o start up the computer from Sleep mode, press the power b utton until the ON/OF F light glows white. The computer retu rns to the screen(s) you were using. If you place the comput er in Sleep mode b y closing the display panel, you can start it again by op[...]

95 Getting Started Caring for your computer Moving the computer Before moving your computer, e ven across the room, make sure all dri ve acti vity has ended (the internal storage drive and optical dri v e indicator lights stop glowing) and al l external peripheral cables are disconnected. Do not pick up the computer by its display panel or by the b[...]

96 Getting Started Caring for your computer 3 Insert the cable’ s locking end into the security lo ck slot on your computer , then engage the locking de vice. The computer is no w securely locked. (Sample Illustration) Attaching security lock cable[...]

97 Chapter 2 Learning t he Basics This chapter giv es some computing tips and provides important information about basic features. Computing tips ❖ Sav e your work frequently . Y our work stays in the computer’ s temporary memory until you sav e it to the internal storage drive. If the netw ork you are using goes down and you must restart your [...]

98 Learning the Basics Computing tips ❖ Back up your files to ex ternal media on a regular basis. Label the backup copies clearly and store them in a safe place. It is easy to put of f backing up because it takes time. Ho wev er , if your internal storage dri ve suddenly fails, you will lose all the data on it unless you hav e a separate backup c[...]

99 Learning the Basics Using the ke yboar d Using the keyboard Y our computer’ s ke yboard contai ns character keys, control ke ys, function ke ys, and special W indo ws ® k eys. (Sample Illustration) Ke yboar d Character keys T y ping with the character keys is very mu ch li ke t yp in g o n a typewriter , e xcept that: ❖ The space bar create[...]

100 Learning the Basics Using the ke yboar d Function keys The functio n keys (no t to be confused with the Fn key) are the 12 keys at the top of the k eyboard. (Sample Illustration) Function ke ys F1 through F12 are called function keys because the y ex ecute programmed functions when pressed. Used in combin ation with the Fn key , fun ction keys [...]

101 Learning the Basics Starting a pr og ram Starting a program The easiest way to start a program is to double-click the name of the file that contains the information you want to work on. T o find the file, use the Start menu or W indo ws ® Explorer . If you prefer to open the program f i rst, you hav e four options. Y ou can: ❖ Double-click t[...]

102 Learning the Basics Starting a pr ogram Starting a program from Windows ® Explorer If a program is not listed in th e All Programs menu, yo u can start it from W indows ® E xplorer . W indo ws ® Explorer gi ves you a view of your computer’ s contents as a hi erarchy or “tree. ” Y ou can easily see the contents of each driv e and folder[...]

103 Learning the Basics Saving your work Starting a program using the Search programs and files field This example uses the Start menu’ s Search programs and f iles field to start W ordPad: 1 Click Start to display the Start menu. The Search programs and files f ield appears at the bottom of the Start menu. (Sample Image) Sear c h pr ograms and f[...]

104 Learning the Basics Saving your work Saving files 1 Click on the arrow in the upper -left corner of your W indows ® -based application to display the drop-down menu, and then click Sav e . If you are working with a docum ent that already has a f ile name, this i s all you need to do. If you created a ne w document, your program displays a Sav [...]

105 Learning the Basics Printing your work Microsoft ® W ord file. Creating your own extension is usually unwise, since the program is unlikely to recognize a strange extension and may refuse to handle your file correctly . TECHNICAL NOTE: By default, the Windows ® operating system does not show file extensions. For information on showing or hidi[...]

106 Learning the Basics Backing up your work 4 Click Print . Backing up your work Back up all the files you create in case something happens to your computer . Y ou can back up your files to dif ferent types of media such as CDs, D VDs, diskettes, or to a network, if a vailable. T o back up sev eral files at one time, use the Microsoft ® Win d o w[...]

107 Learning the Basics Using the optical drive TECHNICAL NOTE: When restoring files, the backup program prompts you if you try to over write a file that already exists on the internal storage drive. Make sure the backup v ersion is the one you want before overwriting the existing file. Using the optical drive Optical storage is a pop ular medium f[...]

108 Learning the Basics Using the optical drive ❖ If your computer includes a standard tray-type opt ical dri ve (av ailable on certain models), see “Inserting an optical disc (tray-type dr iv e)” on page 110 for more information. Drive in-use indicator light —Indicates when the driv e is in use. Eject button —Press to release the disc tr[...]

109 Learning the Basics Using the optical drive The Play/Pause button starts playing the disc or makes it pause if currently playing. The Previous track b utton returns to the preceding track on the disc. The Next track button skips to the follo wing track on the disc. The Vo l u m e c o n t r o l allows you to decr ease and increase the computer?[...]

110 Learning the Basics Using the optical drive Removing a disc (slot-type drive) Do not press the eject button or turn off the computer while the drive in-use indicator light is glowing. Doing so could damage the dis k or the drive. The computer must be powered on to eject a disc. 1 Locate and press the eject b utton. The disc partially ejects fro[...]

111 Learning the Basics Using the optical drive Never use a pencil to press the manual eject button. Pencil lead can break off inside the computer and damage it. T o insert an optical disc into the dri ve: 1 Make sure the computer is turned on. The dri ve will not open if the computer’ s power is of f. 2 Make sure the dri ve’ s in-use indicator[...]

112 Learning the Basics Using the optical drive 6 Place the disc carefully in th e disc tray , label side up. (Sample Illustration) P ositioning the disc in the drive 7 Gently press the disc onto the center spindle until it clicks into place. Handle DVDs and CDs carefully , making contact only with the center hole and edge. Do not touch the surface[...]

113 Learning the Basics Using the optical drive Playing an audio CD Insert an audio CD and close the disc tray . If the computer is turned on, the default player opens. ❖ T o play the CD or to pause, click the Play/Pause button. ❖ T o stop the CD, click the Stop button. Before putting on headphones to listen, turn the volume down. Do not set th[...]

114 Learning the Basics Using the optical drive Due to manufacturing and quality variations in third party optical media (e.g., CD or DVD) or optical media players/recorders, in certain cases, your T oshiba optical drive may not record on certain optical media that bear the applicable logo, or play back optical media recorded by other computers or [...]

115 Learning the Basics T oshiba’ s online r esour ces 2 Pull the tray out until it is fully open , remove the disc, and place it in its protecti ve co ver . 3 Gently press the tray in to close it. Caring for optical discs ❖ Store your discs in their original con tainers to protect them from scratches and k eep them clean. ❖ Do not bend a dis[...]

116 Chapter 3 Mobile Computing This chapter cov ers all aspects of using your com puter while trav eling. T oshiba’ s energy-saver design Y our computer enters a low-po wer suspension mode when it is not being used, thereby conserving energy and sa ving money in the process. It has a number of other features that enhanc e its energy ef ficiency .[...]

117 Mobile Computing Running the computer on battery power Running the computer on battery power The computer contains a remov abl e Lithium-Ion (Li-Ion) battery that provides po wer when you are aw ay from an A C outlet. Y ou can recharg e it many ti mes. Battery Notice Battery life may vary considerably from specif ications depending on product m[...]

118 Mobile Computing Char gi ng batteries TECHNICAL NOTE: Depending on your system, the RTC battery may only charge while the computer is turned on. Power management Y our computer ships with t he power management options preset to a configuration that will prov ide the most stable opera ting en vironment and optimum system performan ce for both A [...]

119 Mobile Computing Char ging ba tteries Charging the main battery T o charge the main battery while it is in your computer, plug the computer into a li ve electrical ou tlet. The battery char ges whether the computer is on or off. TECHNICAL NOTE: The rech arging of the batter y cannot occur when your computer is using all of the pow er provided b[...]

120 Mobile Computing Monitoring main battery power T o recharge the R TC battery , plug the computer into a li v e electrical outlet and leav e the computer powered on for 24 hours. It is seldom necessary to charge the RTC battery because it charges while the computer is on. If the RTC battery is low , the real-time clock and calendar may display t[...]

121 Mobile Computing Monitoring main battery power HINT : Be careful not to confuse the battery light ( ), the ON/OFF light ( ), and the powe r button light (near the upper -left corner of the keyboard). When the ON/OFF light or power button light flashes amber , it indicates that the system is suspended (us ing the Windows ® operating system Slee[...]

122 Mobile Computing Monitoring main battery power Determining remaining battery power Wait at least 16 se conds after turning on the computer before trying to monitor the remaining battery power . The computer needs this time to check the battery’ s remaining capac ity and perform its calculations. Mov e the pointer ov er the po wer icon in the [...]

123 Mobile Computing Monitoring main battery power Setting batter y notifications Y ou can set two notifi cations. Each notification can be set to alert you when a specified percentage of remaining battery po wer has been reached. Y ou can also set the computer to enter Sleep mode or Hibernation mode or to complet ely po wer do wn when the notif ic[...]

124 Mobile Computing Monitoring main battery power ❖ Ho w much you use the internal storage driv e, optical dri ve, diskette dri ves, or other optional de vices ❖ Where you are working, since operating time decr eases at low temperatures There are v arious ways in which you can conserv e power and extend the operating time of your battery: ❖ [...]

125 Mobile Computing Monitoring main battery power 2 Select an appropriate plan for your work en vironment or create your own custom plan. 3 Click Create a po wer plan in the left pane to set up a new plan. T o edit a plan or to edit advanced settings, continue to the following steps. 4 Click Change plan settin gs to choose the plan you want to edi[...]

126 Mobile Computing Using the T OSHIB A eco power plan 2 While continuing to press Fn , press F2 until you select the desired Power Plan. The Po wer Plan options are: eco and Balanced. 3 Release the Fn key . The hot ke y card disappears. Y ou are now in the selected mode. Using the TOSHIBA eco power plan This computer is equipped w ith the T oshib[...]

127 Mobile Computing Changing the main battery Changing the main batter y When your main battery has ru n out of power , you have two options: plug in the A C adaptor or install a char ged main battery . Never short circuit the battery pack by either accidentally or intentionally bringing the battery terminals in contact with another conductive obj[...]

128 Mobile Computing Changing the main battery 6 Slide the battery release latch to release the battery . 7 Pull the discharged battery out of the computer . (Sample Illustration) Removing the battery If the battery is leaking or its case is cracked, put on protective gloves to handle it, and discard it immediately . Always dispose of used battery [...]

129 Mobile Computing Changing the main battery If the battery does not slide into the slot easily , move the battery release lock to the unlocked position and try again. Do not force the battery into position. (Sample Illustration) Inserting the ba ttery 3 Slide the battery release lo ck to the locked position. (Sample Illustration) Locking the bat[...]

130 Mobile Computing T aking car e of your battery T aking care of your batter y The follo wing sections offer tips on how to take care of your battery and prolong its life. Safety precautions ❖ If the battery pack produces an odor , o verheats or changes color or shape while it is being used or charged, turn of f the computer’ s power immediat[...]

131 Mobile Computing T aking car e of your battery Maintaining your batter y Fully discharging your battery pack will allo w better accurac y of the battery meter . T o fully discharge your battery pack: ❖ Periodically , disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges. Before doi[...]

132 Mobile Computing Disposing of used b atteries Disposing of used batteries The life of a battery pack depends on usage. When the battery pack needs replacing, the main battery light flashes amber shortly after you hav e fully rech arged the battery . Y ou must discard a batter y if it becomes damaged. Never attempt to dispose of a battery pack b[...]

133 Mobile Computing T raveling tips Notice regarding CR coin cell batteries, applicable to California, U.S.A. only: Perchlorate Material - special handling may apply . See http://www .dtsc.ca.gov/h azardouswaste/perchlorate/ T raveling tips The en vironmental precautions listed in “Selecting a place to work” on page 43 , also apply while trave[...]

134 Chapter 4 Exploring Y our Computer’ s Features In this chap ter , you will explore so me of the special features of your computer . Exploring the desktop The desktop is the launching pad for everything you can do in the W indows ® operating system. Y ou use its features to start programs, find documents, set up system components, and perform[...]

135 Exploring Y our Computer’ s Features Exploring the desktop Finding your way around the desktop Y our computer’ s desktop includes sev eral standard features: icons, Start button, taskbar , notification area, and background pattern. (Sample Image) W indows ® operating system desktop Icons An icon represents a folder , file, or program that [...]

136 Exploring Y our Computer’ s Features Explorin g the desktop Y our desktop may contain othe r icons depending on your configuration. See W indo ws ® online Help for more specific information on each icon and ho w to use it. Start button Y ou use the Start button to: ❖ Start programs ❖ Open documents ❖ Adjust system settings ❖ Find fil[...]

137 Exploring Y our Computer’ s Features Setting up for communications Setting up for communications T o connect to the Internet, use an online service, or communicate across the telephone lines with another computer , you need: ❖ A browser or communications program ❖ An Internet Service Pro vider (ISP ) or online service if you plan to use t[...]

138 Exploring Y our Computer’ s Features Setting up for communications Connecting your computer to a network Y ou can connect your computer to a network to increase its capabilities and functionali ty using one of its communication ports. Accessing a network T o access a network: ❖ At the of fice, c onnect an Ethernet cable to the Network port [...]

139 Exploring Y our Computer’ s Features Setting up for communications Connecting a modem to a telephone line (A vailable on certain models) Y our computer may come with a built-in modem th at can be connected to a standard voice-grade telephone line. The modem allows you to: ❖ Access the Internet ❖ Communicate with your of fice’ s local ar[...]

140 Exploring Y our Computer’ s Features An overview of using the Internet Connect the built-in modem only to ordinary analog phone lines. Never connect the built-in modem to a digital line (ISDN). Never connect the built-in modem to the digital connector on a public telephone or to a digital private branch exchange (PBX). Never connect the built[...]

141 Exploring Y our Computer’ s Features An overview of using the Internet Internet Service Providers T o connect a computer directly to the Internet, many people and businesses use an Internet Servi ce Provider (ISP). An ISP is a company that has the equipment and the telecommunication lines necessary to maintain an Internet connection. Y ou can[...]

142 Exploring Y our Computer’ s Features An overview of using the Internet Internet features The Internet offers man y types of communicati on tools to help you perform many tasks. ❖ Internet email T o send and recei ve email of yo ur o wn, you need a mailbox on the W eb or an email address. If you hav e an account with an ISP , you can probabl[...]

143 Exploring Y our Computer’ s Features Explorin g audio featur es Uploading to, and downloading files from, the Internet T ransferring files from one co mputer to another is termed uploading (transferring data from your computer to a site on the W eb), or downloading (transferring data from a site on the W eb to your computer). There are sev er[...]

144 Exploring Y our Computer’ s Features Using the W eb Camera Using external speakers or headphones Y our computer is equipped with a full stereo sound system with internal speakers. Instead of usin g the internal speakers, you can connect headphones or a pair of external ste reo speakers. Before putting on headphones to listen, turn the volume [...]

145 Exploring Y our Computer’ s Features Using an ExpressCar d ® The W eb Camera soft ware, by default, should already be running in the notification area. The W eb Came ra indi cator light glows when the W eb Camera is on . For more information o n the software, click Start , All Pr ograms , TOSH I BA , Utilities , and then W eb Camera A pplica[...]

146 Exploring Y our Computer’ s Features Using the Memory Car d Reader Removing an ExpressCard ® 1 Prepare the card for remov al by clicking on the Show hidden icons ( ), if necessary , in the notification area and then selecting the Safely Remo ve Hard ware icon. 2 Select the card or device you want to remo ve. If the system is unable to prepar[...]

147 Exploring Y our Computer’ s Features Using the Memory Car d Reader Inserting memory media The follo wing instructions apply to all types of supported media devices. 1 T urn the media so that the cont acts (metal areas ) are face do wn. 2 Push the media into the ad apter until it locks in place. (Sample Illustration) Inserting memory med ia Wh[...]

148 Exploring Y our Computer’ s Features Using the i.LINK ® port 3 Grasp the card and pull it straight out. (Sample Illustration) Removing memory media Do not remove memory media while data is being written or read. Even when the Windows ® message “copying...” disappears, writing to the media might still be in progress and your data could b[...]

149 Chapter 5 Utilities Y our computer includes sev eral utilities designed to help yo u to reconfigure your system to best meet your individual needs. T o gether , these allo w you to ascerta in certain system details, set additional options, or change default optio ns. These utilities are described in this chapter . The utilities described in thi[...]

150 Utilities TOSHIB A Assist ❖ TOSHIB A Zooming Utilit y ❖ TOSHIB A Button Su pport ❖ TOSHIB A Accessibility ❖ Fingerprint Authentication Utilit y ❖ TOSHIB A eco Utility™ ❖ TOSHIB A Service St ation ❖ TOSHIB A PC Health Monitor ❖ ConfigFree® TOSHIBA Assist The TOSHIB A Assist pro vides qui ck access to computer functions and all[...]

151 Utilities TOSHIB A Assist Connect The features av ailable in this category are: ❖ ConfigFree ® Connectivity Doctor ❖ Bluetooth ® Settings (Sample Image) T OSHIBA Assist window – Connect tab[...]

152 Utilities TOSHIB A Assist Secure The features av ailable in this category are: ❖ Supervisor password ❖ User password (Sample Image) T OSHIBA Assist window – Secur e tab[...]

153 Utilities TOSHIB A Assist Protect & Fix The features av ailable in this category are: ❖ TOSHIB A PC Diagnostic T ool Utility ❖ TOSHIB A HDD Protection Utility (Sample Image) T OSHIBA Assist window – Pr otect & Fi x tab[...]

154 Utilities TOSHIB A Assist Optimize The features av ailable in this category are: ❖ TOSHIB A SD™ Memor y Card Format Util ity ❖ Mouse Utility ❖ TOSHIB A Hardware Se tup (Hardware Settings) ❖ TOSHIB A Zooming Utilit y ❖ TOSHIB A Button Su pport ❖ TOSHIB A Accessibility ❖ TOSHIB A Face Recognition Utility ❖ USB Sleep and Charge U[...]

155 Utilities TOSHIB A Applicati on Installer TOSHIBA Application Installer The TOSHIB A Application Installer allows you to reinstall the dri vers and applications that were originally bundled with your computer . T o reinstall driv ers and applications: 1 Click Start , All Programs , My To s h i b a , and then TO SH I BA Application Installer . 2[...]

156 Utilities Setting passwor ds Setting passwords Setting a password lets you walk away from your computer while providing additional protection for your files. When you set a password, you must enter the password before you can w ork on your computer again. T oshiba supports se ve ral types of passwords on you r computer: ❖ An instant password?[...]

157 Utilities Setting passwor ds Using a supervisor password A supervisor password pre vents other users from changing hardware configuration options. Setting a supervisor password If you choose to set a supervisor or user password, T oshiba strongly recommends that you save your password in a location where you can later access it should you not r[...]

158 Utilities Setting passwor ds 6 Click OK . The supervisor password u tility dialog bo x appears. 7 Select Able to run HWSetup or Unable to run HWSetup and then Click OK . 8 Restart the system to complete the process. Deleting a supervisor password T o delete a supervisor passwor d: 1 Click Start , All Programs , TOSH IBA , Utilities , and then T[...]

159 Utilities Setting passwor ds T o register a password for the po wer- on password functions: 1 Click Start , All Programs , TOSH IBA , Utilities , and then TOS H IBA HWSetup . The TOSHIB A HWSetup windo w appears. (Sample Image) TOSHIB A P asswor d tab 2 Select the Passw ord tab . 3 Click Registered . 4 Enter your pas sword, and then enter it ag[...]

160 Utilities TOSHIB A F ace Recognition Utility TOSHIBA Face Recognition Utility Y our computer may come with the TOSHIB A Face Recognition utility . This utility provides another way to log on to y our computer . For high security purposes, TOSHIBA Face Recognition is not a suitable substitute for Windows ® passwords. T o ensure the security of [...]

161 Utilities TOSHIB A PC Dia gnostic T ool Utility TOSHIBA PC Diagnostic T ool Utility This utility can h elp diagnose pro blems with devices in your computer . Refer to the online Help documentatio n within the application for additional help. The TOSHIBA PC Diagnostic T ool u tility may show tests for features you do not have. This is normal and[...]

162 Utilities TOSHIB A HDD Pr otection Utility TOSHIBA HDD Protection Utility The TOSHIB A HDD Protection Utility controls your compu ter’ s hard disk dri ve (HDD) protection feature, which parks the HDD whene ver motion is detected on the computer . Using this utility , you can enable or disable hard disk driv e (HDD) protection, and set the mot[...]

163 Utilities TOSHIB A SD™ Memory Car d F ormat Utility TOSHIBA SD ™ Memor y Card Format Utility This utility is u sed to format SD ™ cards used with the Memory Card Reader . T o format an SD memory card using this utility: 1 Click Start , All Pr ograms , TOS HI BA , Utilities , and then SD Memory Card F ormat . The TOSHIB A SD Memory Card F [...]

164 Utilities Mouse Utility Mouse Utility The Mouse utility allows you to change your pointing device or mouse settings. T o access the Mouse utility: 1 Click Start , Contro l Panel , Hardware and Sound , and then under Devices and Printers , click Mouse , or click the Mouse icon in the Op timize tab of TOSHIB A Assist . The Mouse Properties screen[...]

165 Utilities TO S H I B A H a rd w a re S e t u p TOSHIBA Hardware Setup TOSHIB A Hardware Setup is the T oshiba con figuration management tool av ailable through th e W indows ® operating system. T o access it: ❖ Click Start , All Programs , TOSH IBA , Utilities , and then HWSetup , or click the TO S HI BA H a rdw a re S e tt in g s icon in th[...]

166 Utilities TO S H I B A H a rd w a re S e t u p Select the boot device b y pressing the arro w keys, then pressing the Enter key . Since the system is a quick-booting sy stem, you must press the keys immediately after pressing the power button. ❖ Button Sett ing —Lets you set the conditions for th e po wer button and/or the other buttons (Sa[...]

167 Utilities TO S H I B A H a rd w a re S e t u p ❖ General —Allows you to vie w the current BIOS version or change certain settings back to their default values ❖ Ke y b oa rd —All ows you to access the w ake-on keyboard function ❖ LAN —Allows you to set networking functions ❖ Illumination— Allows you to set the panel LED and ke y[...]

168 Utilities USB Sleep and Char ge Utility USB Sleep and Charge Utility This utility displays w hether the “USB Sleep and Charge function” is enabled or disabled and shows the position of the USB port that supports the “USB Sleep and Charge function. ” It also displays the remaining battery capacity . Starting the USB Sleep and Charge Util[...]

169 Utilities USB Sleep and Char ge Utility ❖ When “USB Sleep and Charge function” is set to Enabled, USB bus power (DC 5V) will be supplied to the compatible port even when the power of the computer is turned OFF . USB bus power (DC 5V) is similarly supplied to the external devices which are connected to the compatible ports. However , some [...]

170 Utilities USB Sleep and Char ge Utility Enabling USB Sleep and Charge This utility can b e used to enable or disable the “USB Sleep and Charge function” group . Check the check box fo r the group to enable the “USB Sleep and Charge function” for the USB port assigned to that group. In the default state, the group is disabled. Power supp[...]

171 Utilities TOSHIB A Zooming Utility TOSHIBA Zooming Utility This utility allows you to select which applications will work with the zoom in/out hot ke ys (see “Zoom (Display resolu tion)” on page 227 ). Y ou may select all applications or any subset of the following: ❖ Microsoft ® Internet Explorer ® ❖ Microsoft ® Of f ice ❖ W indo [...]

172 Utilities TOSHIB A Button Support TOSHIBA Button Support TOSHIB A Button Support allows you to customize the Mute and Media buttons . These buttons ar e located on the system control panel directly above the keyboard. T o access TOSHIB A Button Support: 1 Click the TOSHIB A Button Support icon in the Optimize tab of TOSHIB A Assist . The TOSHIB[...]

173 Utilities TOSHI BA A ccessibility TOSHIBA Accessibility The TOSHIB A Accessibility utility allows you to use the Fn ke y to create a hot key combination wit h one of the function ke ys without pressing the two keys simultaneously as is usually required. Using Accessibility lets you make the Fn key a sti cky key , meaning you can press it once, [...]

174 Utilities F ing erprint Authenticati on Utility Fingerprint Authentication Utility (A vailable on certain models) The fingerprint authentication utility (av ailable on certain models) can be used to replace the ke yboard-based user password authentication system when booting up. The fingerprint authentication uti lity can also be us ed for user[...]

175 Utilities F ing erprint Authent ication Utility The Fast User Switching feature of the W indo ws ® operating sy stem is also supported. If user A is logged on and the fingerprint utilit y verif ies the fingerprint of user B (who is already enrolled), the utility recognizes the fingerprint and switches th e users. If your system support s power[...]

176 Utilities F ing erprint Authenticati on Utility Observe the follo wing to improve the fi ngerprin t recognition success rate. ❖ Enroll two or more fingers. ❖ Enroll additional fingers if r ecognition failure occurs often using enrolled fingers. ❖ Check your finger condition. Changed conditions, such as injured, rough, extremely dry , wet,[...]

177 Utilities TOSHI BA eco Utility™ TOSHIBA eco Utility™ The T oshiba eco u tility™ monitors y our power sa vings from using the eco po wer plan by tracking real-time po wer consumption and accumulated savings o ver time. T o access the T oshiba eco utility ™, do one of the follo wing: ❖ Click Start , All Programs , TOS H IBA , Utilities [...]

178 Utilities TOSHIB A Service Station TOSHIBA Service Station The TOSHIB A Service Station helps you keep your ne w computer running at its best by notifying you when updated software, firmw are, documentation or othe r information is av ailable for your computer . The TOSHIBA Service Station will alert you when updates are av ailable, and you can[...]

179 Utilities ConfigF r ee® The TOSHIB A PC Health Mo nitor software does n ot extend or modify T oshiba's obligatio ns under its standard limited warranty in any way . T oshiba's standard limit ed warranty te rms and limitat ions apply . ConfigFree ® All references to Bluetooth ® in this section are applicable only if Bluetooth ® is [...]

180 Utilities ConfigF r ee® If your computer is not connected to a network, the ConfigFree icon in the notification area is displayed with an “X.” ConfigFree ® Utilities Connectivity Doctor The Connectivity Doctor lets you analyze your network connections and fix network connection prob lems. Using Connectivity Doctor , you can vie w detailed[...]

181 Utilities ConfigF r ee® Profile Settings The Prof ile Settings utility lets you save network settings in “profiles . ” ConfigFree ® prof iles are useful for easily switching network settings an d devices. Y ou can switch network settings simply by selecting the profile with the desired settings. If you visit a client company occasionally [...]

182 Utilities ConfigF r ee® 3 Click Open Settings . The ConfigFree Prof ile Settings windo w appears. (Sample Image) ConfigF ree Pr ofile Settings windo w 4 Click Add to start the Creat e Profile W i zard.[...]

183 Chapter 6 If Somet hing G oes W r o ng Some problems you may encounter wh en using your computer are relativ ely easy to identify and solve. Others may require help fro m your network administrator or the manufacturer of the software program. This chapter aims to help you solve many problems b y yourself. It cov ers the problems you are most li[...]

184 If Something Goes Wrong Pr oblems when you turn on the computer 2 Click the A pplications tab . If a program has stopped responding, the words “not responding” appear beside its name in the list. 3 Select the program you want to close, then click End T ask . Closing the failed prog ram should allow you to continue working. If it does not, c[...]

185 If Something Goes Wrong Pr oblems when you turn on the computer If you are using an A C adaptor , v e rify that the computer is recei ving power from the external po wer source by looking at the A C power light. If the indicator is glo wing, th e computer is connected to a liv e external po wer source. The computer starts but when y ou pr ess a[...]

186 If Something Goes Wrong Pr oblems when you turn on the computer The computer displays the Non-System disk or disk error messag e. Make sure there is no diskette in the optional e xternal diskette driv e. If there is a diskette in th e dri ve, remo ve it and press an y key to continue. If pressing an y ke y does not work, press Ctrl, Alt , and D[...]

187 If Something Goes Wrong The W indo ws ® operating system is not working plug fits correctly in the DC -IN socket. The labels on the bottom of the computer and the A C adaptor show the specifications for v oltage ("V") and current ("A") for each device. The v oltage le vel must match exactly . The amperage rating of the A C [...]

188 If Something Goes Wrong The W indo ws ® operating system is not working ❖ Enable Boot Logging ❖ Enable low-resolution video (640x480) ❖ Last Kno wn Good Conf iguration (adv anced) ❖ Directory Services Restore Mode ❖ Deb uggin g Mode ❖ Disable automatic restar t on system failure ❖ Disable Driv er Signature Enforcement ❖ Start W[...]

189 If Something Goes Wrong F ixing a pr oblem with Device Manag er The Windows ® operating system can help you If the operating system has started properly but you still ha ve a problem using your co mputer , the onli ne Help can assist you in troubleshooting the pro blem. T o access the W indo ws ® operating system Hel p and Support: 1 Click St[...]

190 If Something Goes Wrong Memory pr oblems 3 T o view the properties, double-click the de vice. The operating system displays the de vice Properties dialog box, which provides an array of tabs. They may include: ❖ The General tab, which provides basi c information about the device. ❖ The Resources tab, which lists resources assigned to the de[...]

191 If Something Goes Wrong P ower and the batteries TECHNICAL NOTE: Y ou must have at least one memory module installed for the computer to work. For this model, Slot A is the bottom slot. Slot B is the top slot. If only one memory module is to be installed, it must be installed in Slot A. Power and the batteries Y our computer receive s its po we[...]

192 If Something Goes Wrong K e yboar d pr oblems If the battery light does not glow after 20 minutes, the batter y may hav e reached the end of its useful life. T ry replacing it. The battery appears not to power the computer f or as long as it usually does. If you frequently repeat shallow char ge and discha rge, the battery meter may beco me ina[...]

193 If Something Goes Wrong Display pr oblems Y ou may have acti v ated the instan t password feature by pressing Fn and F1 simultaneously . If you ha ve re gistered a password, press any ke y , type the password and press Enter . If no password is registered, press an y ke y . The s cr een reactiv ates and allo ws you to continue working . If you [...]

194 If Something Goes Wrong Disk or storag e drive pr oblems 2 Click Personalize , and then Di splay . 3 Adjust the screen resolution and/or color qualit y . 4 Click OK . The display mode is set to Simultaneous and the exter nal display de vice does not work. Make sure the e xternal monito r is capable of displaying at resolutions of 800 x 600 or h[...]

195 If Something Goes Wrong Disk or storag e drive pr oblems 3 On the pop-up menu, click Properties . The dri ve’ s Properties box appears. This feature is not available for optical drives. 4 Click the T ools tab. 5 Click the Check now ... button. The Check Disk box appears. 6 Y ou can choose one or both options: ❖ Automatically f ix f ile syst[...]

196 If Something Goes Wrong Optical drive pr oblems (tra y-type drive) replace the diskette. If the label is loose, replace the label and try inserting the diskette again. The drive cannot r ead a diskette. T ry another diskette. If you can access the second diskette, the first diskette (not the drive) is probably causi ng the problem. Run Error-ch[...]

197 If Something Goes Wrong Sound system pr oblems media formats, refer to the complete detail specifications for your computer at pcsupport.toshiba.com . If the problem is with an optical dat a disc, refer to the software’ s documentation and check that the hardware configuration meets the program’ s needs. The disc will not come out of the dr[...]

198 If Something Goes Wrong Expr essCar d ® pr oblems ❖ Occasionally a defecti ve ExpressCard ® slips through quality control. If another computer wit h a ExpressCard slot is av ailable, try the card in that machine. If the car d malfunctions again, it may be defecti ve. Resolving ExpressCard ® problems Here are some common problems and their [...]

199 If Something Goes Wrong Printer pr oblems Never swap modules when the computer is in Hibernation or Sleep mode. This is known as “warm swapping” and is not supported. For more information on Hibernation and Sleep modes see “Hibernation mode” on page 85 and “Sleep mode” on page 86 . The system does not r ecognize your ExpressCard ® [...]

200 If Something Goes Wrong Modem pr oblems If you cannot resolve the problem, contact the printer’ s manufacturer . The printer will not print wh at y ou see on the scr een. Many programs display information on the screen differently from the way they print it. S ee if your program has a print previe w mode. This mode lets you see your work exac[...]

201 If Something Goes Wrong W ireless networking pr oblems ❖ V e rify that your computer can det ect access points or routers. If it can detect a W i-Fi ® access point or router then it may be a configuration issue. ❖ V erify that signal strength is good usin g the utility provided with the W i-Fi ® adapter . ❖ If another computer is on the[...]

202 If Something Goes Wrong D VD operating pr ob lems ❖ Use the PING command to verify a connection to the gate way at 192.168.1.1 (a default gatew ay for most wireless routers). 1 Click Start to open the Start menu. 2 T y pe Cmd in the Search programs and files f ield. 3 Enter PING 192.168.1.1 at the command pr ompt, and press Enter . If “Requ[...]

203 If Something Goes Wrong Develop good computing habits 6 See “Checking device properties” on page 189 for instruc tions on using Device Manager to vie w the optical driv e properties. 7 Check the T oshiba W eb site for new information on optical dri ves and their operation. A blank scr een appears while watching a D VD-R OM movie or title. C[...]

204 If Something Goes Wrong Develop good computing habits Some people use a combination of th ese methods, backing up all files to tape weekly and copying cr itical files to diskette on a daily basis. If you hav e installed your own programs, you should back up these programs as well as your data file s. If something goes wrong that requires you to[...]

205 If Something Goes Wrong Develop good computing habits Follo w these steps to create a restore point using the System Restore utility: 1 Click Start , Contro l Panel , System and Security , and then System . 2 In the left pane click Sys tem protection . The System Protecti on tab of th e System Properties windo w appears. 3 Click Create... 4 In [...]

206 If Something Goes Wrong Develop good computing habits Backing up your data or your entire computer with the Windows ® operating system The most v aluable component of y our computer system is the data you create and store on its internal storage drive. Since problems with either hardware or softw are can make the data inacces sible or ev en de[...]

207 If Something Goes Wrong Develop good computing habits then be able to easily restore the W indows ® operating system to the state it was in prior to the installation, undoing any changes that the installatio n process introduced. ❖ Back up your critical data (see “Backing up your data o r your entire computer with the Windo ws® operating [...]

208 If Something Goes Wrong Develop good computing habits Cannot use the “USB Sleep and Char ge function. ” ❖ The setting of “USB Sleep and Charge function” may be Disabled. Change the setting to Enabled. ❖ Some external devices may not be able to use the “USB Sleep and Charge function. ” In this case, please try one or more of the [...]

209 If Something Goes Wrong If you need further assistance If you need further assistance If you have follo wed the recomm endations in this chapter and are still having problems, you may n eed additional technical assistance. This section contains the step s to take to ask for help. Before you contact T oshiba Since some problems m ay be related t[...]

210 If Something Goes Wrong Other T oshiba Internet W eb sites T oshiba voice contact Before calling T o shiba, make sure you have: ❖ Y our computer’ s serial number ❖ The computer and any optional devices related to the problem ❖ Backup copies of your W indows ® operating system and all other preloaded software on your choice of media ❖[...]

211 If Something Goes Wrong T oshiba’ s worldwide of fices T oshiba’ s worldwide offices A ustralia T oshiba (Australia) P ty . Limited 84-92 T alav era Road North Ryde NSW 2113 Sydney Australia Canada T oshiba Canada Ltd. 191 McNabb Street Markham, Ontario L3R - 8H2 Canada France T o shiba Systèmes (France) S.A. 7, Rue Ampère; B. P . 131 928[...]

212 If Something Goes Wrong T oshiba’ s worldwide off ices For more information on additio nal T osh iba worldwide locations, please visit: www .t oshiba.co.jp/index.htm . United States T o shiba America Information Systems, Inc. 9740 Irvine Boulev ard Irvine, California 92618 United States The Rest of Europe T oshiba Europe (I .E.) GmbH Hammfeld[...]

213 5.375 x 8.375 ver 2.3 Appendix A Hot Keys/TOSHIBA Cards Hot ke ys and TO SHIB A Cards provi de a quick way to modify selected system functions and to launch applications. There are two types of T OSHIB A Cards: Hot Ke y Cards and Application Cards. Hot Key Cards The Hot Ke y Cards are used to set or modify the following system functions: ❖ Mu[...]

214 Hot Keys/TOSHIBA Cards Hot K e y Car ds 5.375 x 8.375 ver 2.3 Using the Hot Key Cards The Hot Ke y Cards are normally hidden from view . The Cards appear when you press the Fn key . Hot keys are keys that, when pressed in combina tion with the Fn key , turn system functions on and off. Hot keys have a legend on the key indicating the option or [...]

215 Hot Keys /TOSHIBA Ca rds Application Cards 5.375 x 8.375 ver 2.3 Application Cards The Application Cards are used to launch these applications: TOSHIB A Assist For more information, refer to “TOSHIB A Assist” on page 150 . TOSHIB A HDD Protection utility For more information, refer to “TOSHIB A HDD Protection Utility” on page 16 2 . PC [...]

216 Hot Keys/TOSHIBA Cards Application Car ds 5.375 x 8.375 ver 2.3 Not all functions are supported on all models. Using the Application Cards T o launch an application using the Applicati on Cards: 1 Press and hold the Fn ke y . The TOSHIB A Cards display at the top of the screen. (Sample Image) TOSHIB A Car d display 2 Click the “stack ed” ca[...]

217 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Card Case The Card Case feature allows you to choose which cards appear in the Application Car d display (see “Using the Applicati on Cards” on page 216 ). T o use the Card Case: 1 Click Start , All Programs , TOSH IBA , Utilities , and then Settings for Flash Cards . (Sample[...]

218 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Volume Mute or Fn + This TOSHIB A Card or hot ke y enables/disables volume mute on your computer . When volume mute is enabled, n o sound will com e from the speakers or headphones. Selecting this Card or pressing the hot key displays the following options: (Sample Image) V olume M[...]

219 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Lock (Instant security) The Fn + F1 hot key function acti v ates instant security . The user logon screen will appear and a user with a valid account will need to log back on to gain access to the computer . or Fn + This TOSHIB A Card or hot ke y blanks the display . Selecting th[...]

220 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Power plan or Fn + This TOSHIB A Card or hot ke y displays the power plans and cycles through the power plans. The properties of each po wer plan, and the po wer plans that are displayed by this function, are set in the Power Options window . Selecting this Card or pressing the hot[...]

221 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Sleep mode or Fn + This TOSHIB A Card or hot k e y places the computer into Sleep mode. For more information about Sleep mode, please see “Using and configuring Sleep m ode” on page 91 . Selecting this Card or pressing the hot ke y displays the following options: (Sample Imag[...]

222 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Hibernation mode or Fn + This TOSHIB A Card or hot k e y places the computer into Hibernatio n mode. If Hibernation mode is disabled, this hot key will not respond. For more information on Hibernation mode, see “Using and configuring Hibernation mode” on page 89 . Selecting thi[...]

223 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Output (Display switch) or Fn + This TOSHIB A Card or hot ke y cycles through the power - o n d i sp l a y o p t io n s (only the f irst option is av ailable when you do not have an external monitor attached) (the last option is available only if you are in Extend ed Display Mode[...]

224 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Display brightness Cycle through the display modes, th en select the desired mode. Not all functions are supported on all models. Some systems also support an additional Swap Image Display mode. This mode is available only if the current setting is an extended desktop mode (Built-i[...]

225 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Disabling or enabling wireless devices or Fn + This TOSHIB A Card or hot ke y enables/disables th e optional wireless devices installed in your computer . The wireless modes are: ❖ Wi - F i ® enabled—Enables just the Wi-Fi ® module. ❖ Bluetooth ® enabled—Enables just t[...]

226 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Disabling or enabling the T ouchPad™ or Fn + This TOSHIB A Card or hot ke y enables/disables th e T o uchPad. For more information on using the T ou chPad, see “Using the T o uchPad™” on page 75 . Selecting this Card or pressing the hot key displays the following options: ([...]

227 Hot Keys /TOSHIBA Ca rds Hot ke y functions 5.375 x 8.375 ver 2.3 Zoom (Display resolution) or Fn + [ Space bar ] This TOSHIB A Card or hot key switches screen resolution. Selecting this Card or pressing the hot ke y displays the following options: (Sample Image) Scr een r esolution options Cycle through the screen resolu tions, then select the[...]

228 Hot Keys/TOSHIBA Cards Hot ke y functions 5.375 x 8.375 ver 2.3 Keyboard hot key functions Fn + This hot ke y t urns the T OSHIB A Z oo mi n g Utility to zoom out. Fn + This hot ke y turns th e TOSHIB A Zooming Utility to zoom in. Fn + This hot key turns the backlit keyboard off and on. (A vailable on certain models) The default Fn + Z toggle f[...]

229 5.375 x 8.375 ver 2.3 Appendix B P o wer Cord/Cable C o nnector s Y our computer ships w ith the correct power su pply for the country of purchase. This appendix shows the shapes of the typical A C po wer cord/cable connectors fo r v arious parts of the world. USA UL ap pr oved Canada CSA approv ed United Kingdom BS ap pr oved Europe VD A appro[...]

230 Glossar y TECHNICAL NOTE: Some features defined in this glossary may not be available on your computer . Acronyms The follo wing acronyms may app ear in this user’ s guide. AC alternating current BIOS basic input/output system bps bits per second CD compact disc CD-R OM compact disc read-only memory CD-R W compact disc rewrite memory CMOS com[...]

Glossary 231 DOS disk operating system DPI dots per inch DSTN dual supertwist nem atic DV D digital versatile (or video) disc DV D - R O M dig ital versatile (or video) disc read-only memory ECP enhanced capabil ities port EPR OM erasable programmable read-only memory eSA T A external Serial Advanced T echno logy Attachment FAT f ile allocation tab[...]

232 Glossary RFI radio frequency interference RO M read-only memory RT C real-time clock SCSI small computer system interface SD Secure Digital SDRAM synchronous dynamic ran dom access memory SRAM static random access memory SSD Solid State Driv e SVGA super video graphics adapter TFT thin film transistor USB universal serial bu s URL uniform resou[...]

Glossary 233 application — A computer program that yo u use to perform tasks of a specific type. Applications includ e wo rd processors, spreadsheets, and database management systems. See also pro gram . B backup — A copy of a file, usually on a remov able disk, kept in case the original file is lost or damaged. basic input/o utpu t system (BIO[...]

234 Glossary CD — An individual compact disc. See also CD-R OM. CD-R OM (compact disc r ead-only memory) — A form of high- capacity storage that uses laser opt ics instead of magnetic means for reading data. See also CD . Compare DV D - RO M . central processing unit (CPU) — The chip that functions as the “brain” of the computer . It take[...]

Glossary 235 cursor — An on-screen symbol (usually a flas hing verti cal line) that indicates the position where charact ers will appear when you enter data. D default — The setting selected by a program when the user does not specify an alternati ve setting. device — A component attached to the computer . Devices may be external (outside the[...]

236 Glossary document — Any file created with an application and, if sa ved to disk, gi ven a name by which it can be retrie ved. See also fil e . double-click — T o press and release the pointing device’ s primary button rapidly twice without moving the pointing device. In the W indows ® operating system, this refers to the pointing device?[...]

Glossary 237 F fil e — A collect ion of related information, saved on disk with a unique name. A file may be a program, information used by a program, or a document. See also docum ent. f ile allocation table (F A T) — The section of a s t o r a g e d r ive that keeps track of the location of stored files. fil e n am e — A set of char acters [...]

238 Glossary Hibern ation — A feature of many T oshiba computers that saves to the i n t e r n a l s t o r a g e d r iv e the current state of your work, including all open files and programs, when you turn the computer off. When you turn on the computer again, your work is returned to the same state it was when the computer was turned of f. See [...]

Glossary 239 liquid crystal disp lay (LCD) — A type of display that uses a liquid substance between two transparent electrode panels. When an electric current passes through the electrodes, the molecules in the liquid form a crystalline pattern that polarizes the light passing through it. A filter o ver the electrodes permits only non-polarized l[...]

240 Glossary N network — A collection of computers a nd associated de vices that are connected by communications facilities. A network allows you to share data and peripheral de vices, su ch as printers, with other users and to exchange electronic mail. non-interlaced — A method of refreshing a computer scr een, in which each pixel of e very li[...]

Glossary 241 Plug and Play — Generally , refers to the com puter’ s ability to automatically configure itsel f to work with peripheral devices. When capitalized, refers to a sta ndard that, when followed by a device manufacturer , allo ws a computer to conf igure itself automatically to work with the device. pointer — An icon (usually an arro[...]

242 Glossary res ta r t — Synonymous with reboot. T o reset the computer by reloading the operating system without tu rn ing the computer off. See also boot . RJ11 — A modular connector used o n most U.S. telephone syst ems and direct-connect modems. The RJ11 co nnector is a 6-wire connector . R OM (read-only memory) — Non-v olatile memory th[...]

Glossary 243 system prompt — The symbol (in the MS-DOS ® operating system, generally a drive letter followed b y a “greater than” sign) indicating where users are to enter commands. T TFT display — See active-matr ix display . U universal serial bus (USB) — USB is a serial b us that supports a data transfer rate of up to 4 80 Mbps (480 m[...]

244 Index A A C adaptor 47 A C po wer (DC-IN) connecting adaptor 48 A C power light 47 Alt keys 99 Application Cards 215 audio fil e s 143 audio features 143 B backing up files 98 battery Call2Recycle™ 132 changing 127 charge indicator light 49 charge not lasting 192 charging 49 , 119 conserving po wer 123 disposal 132 installing 12 7 , 128 lo w [...]

245 Index changing main battery 127 character keys 99 charging the battery 49 checking device properties 189 communications network connection 138 set up 137 compact discs handling 109 inserting 109 compact discs (slot-type driv e) removing 110 computer caring for 94 cleaning 94 moving 95 non-system disk or disk error message 186 not accessing disk[...]

246 Index eject, optical driv e 108 , 110 ENERGY ST AR® 38 error messages non-system disk or disk error 186 problem with display settings/ current settings not wor king with hardware 193 warning resume failure 185 Error-checking 194 eSA T A connecting to the eSA T A/USB combo port 208 eSA T A/USB combo port Using 148 exploring the desktop 134 Expr[...]

247 Index desktop 135 moving to desktop 135 recycle bin 135 safety 41 inserting CDs and D VDs 109 ExpressCards® 145 installation memory module 53 installing main battery 127 , 128 memory modules 53 mouse 82 Internet bookmarked site not found 188 connecting to 141 features 142 slow connection 188 surfing 141 uploading and downloading files 143 URL [...]

248 Index notification area 136 O optical disc handling 112 inserting (slot-type driv e) 109 inserting (tray-type drive) 110 positioning 112 optical driv e driv e in-use indicator light 108 , 110 eject button 10 8 , 110 manual eject hole 108 , 110 problems 196 remo ving disc 114 troubleshooting 196 using 107 optical media recording 113 other docume[...]

249 Index high-pitched noise 19 7 Internet bookmarked site n ot found 188 Internet connection is slo w 188 keyboard not responding 185 missing files /trouble accessing a dri ve 194 modem not recei ving or transmitting 200 no sound 197 non-system disk or disk error 186 power and batteries 191 printer 199 , 200 program not responding 183 program not [...]

250 Index start button 136 starting a program 101 Search programs and f iles field 103 W indo ws® Explorer 102 W indows® Start menu 101 starting up the computer from Shut down 89 from Sleep 94 Startup menu problem solving 187 supervisor password, deleting 158 supervisor password, set up 157 T taskbar 136 telephone line connecting to mo dem 139 te[...]

251 Index using 144 We b s i t e s 209 Wi - F i ® wireless netw orking 137 W indo ws® Explorer 102 W indows® operating system Help and Support 18 9 problem solving 187 W indows® operating system desktop 134 W indows® Start menu 101 wireless netw orking 137 W izards Connect to the Internet 138 wizards Connect to the Internet 138 W orld W ide W [...]